According to PLL1443XA and PLL1416X spec,
"When BYPASS is 0 and RESETB is changed from 0 to 1, FOUT starts to
output unstable clock until lock time passes. PLL1416X/PLL1443XA may
generate a glitch at FOUT."
So set BYPASS when RESETB is changed from 0 to 1 to avoid glitch.
In the end of set rate, BYPASS will be cleared.
When prepare clock, also need to take care to avoid glitch. So
we also follow Spec to set BYPASS before RESETB changed from 0 to 1.
And add a check if the RESETB is already 0, directly return 0;
Fixes: 8646d4dcc7fb ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN supports CPU running at 1.5GHz/1.4GHz/1.2GHz, add missing
frequency for ARM PLL table.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add .rate_count assignment which is necessary for searching required
PLL rate from the each PLL table.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To Frac pll, the gate shift is 13, however to Int PLL the gate shift
is 11.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is enabled by default but if it's not explicitly defined and marked
as critical then its parent might get turned off.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* Replace to audio_pll2_clk with audio_pll2_out
* Replace sys3_pll2_out with sys_pll3_out
* Replace sys1_pll_40m with sys_pll1_40m
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: 96d6392b54db ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* There is no video_pll2 on imx8mm, replace with dummy
* Replace reference to sys_pll3_clk with sys_pll3_out
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: ba5625c3e272 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "sys3_pll2_out" CLK was removed in refactoring so all references
need to be updated to "sys3_pll_out"
Fixes: e9dda4af685f ("clk: imx: Refactor entire sccg pll clk")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Initially, the TMU_ROOT clock was marked as critical, which automatically
made the AHB clock to stay always on. Since the TMU_ROOT clock is not
marked as critical anymore, following commit:
"clk: imx8mq: Remove CLK_IS_CRITICAL flag for IMX8MQ_CLK_TMU_ROOT"
all the clocks that derive from ipg_root clock (and implicitly ahb clock)
would also have to enable, along with their own gate, the AHB clock.
But considering that AHB is actually a bus that has to be always on, we mark
it as critical in the clock provider driver and then all the clocks that
derive from it can be controlled through the dedicated per IP gate which
follows after the ipg_root clock.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Call imx_register_uart_clocks() API to keep uart clocks enabled
when earlyprintk or earlycon is active.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_register_uart_clocks_hws() function is NOT implemented
at all, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Earlycon's clock could be disabled during kernel boot up,
if earlycon is enabled and its clock is gated, then kernel
boot up will fail. Make sure earlycon's clock is enabled
during kernel boot up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no strong reason for this to use CLK_OF_DECLARE instead
of being a platform driver. Plus, this will now be aligned with the
other i.MX8M clock drivers which are platform drivers.
In order to make the clock provider a platform driver
all the data and code needs to be outside of .init section.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e272 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has no sys3_pll2_out clock, PWM3 clock's mux option #4
should be sys_pll3_out, sys3_pll2_out is a typo, fix it.
Fixes: ba5625c3e272 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that the i.MX6 and i.MX7 clock drivers have been switched to clk_hw based,
we can remove the clk based API that is not used by any i.MX clock driver.
The following APIs are going away now:
- imx_clk_busy_divider
- imx_clk_busy_mux
- imx_clk_fixup_divider
- imx_clk_fixup_mux
- imx_clk_mux_ldb
- imx_clk_gate_dis_flags
- imx_clk_gate_flags
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mq datasheet of CCM, the parent of usb1_ctrl_root_clk
and usb2_ctrl_root_clk is usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX8MQ_CLK_TMU_ROOT is ONLY used for thermal module, the driver
should manage this clock, so no need to have CLK_IS_CRITICAL flag
set.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename 'share_count_dcss' to 'share_count_disp', since the
DCSS module does not exist on imx8mm platform. So rename it
to avoid any unnecessary confusion.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mm datasheet of CCM, the parent of usb1_ctrl_root_clk
should be usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For i.MX clock drivers probe fail case, clks should be unregistered
in the return path, this patch adds a common API for i.MX clock
drivers to unregister clocks when fail.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1416X/1443X PLL are used on i.MX8MM and i.MX8MN and maybe
other i.MX8M series SoC later, the macro definitions of
these PLLs' initialization should be common for usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix several warnings/errors in validation of binding schemas.
-----BEGIN PGP SIGNATURE-----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=IkH4
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"Fix several warnings/errors in validation of binding schemas"
* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
dt-bindings: iio: ad7124: Fix dtc warnings in example
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
dt-bindings: Ensure child nodes are of type 'object'
Pull vfs documentation typo fix from Al Viro.
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
typo fix: it's d_make_root, not d_make_inode...
-----BEGIN PGP SIGNATURE-----
iQGzBAABCgAdFiEE6fsu8pdIjtWE/DpLiiy9cAdyT1EFAl0zg9YACgkQiiy9cAdy
T1HEtQv/Vn2vb9jPoqbCc5QfSUDL13dNYyxhqt3xPdbb3m49a7XNHLoBByM/pnMu
TF10QdOPkPS5eP5OTDpR7iwS9iNX9+8KGtlqlbzX7z+bwQmGbBQXg3VoYahSeeGU
soJE8VgqoeoOkPV9Sl8tojOIVk6B+BAv4iRPpswt8iPD8Y8IPRg3ONZNoomybzfG
GlQBFabhxJU8VLkJIb4NVB+E4AlgMDueD7HpCXD2zh6xsEULgRs2wwxfEopZlyzh
prjNY6OZliXMuTMNLw2D07xlya3ZqaXOt+hHEuvSB//YxooTVxBme70ycLF47N3q
Gvmaw8QB6scl110PHud9luqpHhdJsEvKOKr0Amv2ND2Atb098D0kZ+VITRP3QHt5
LZcHtKNRXDpAvkHphgN0W5O0ngdFDFo197BaWdwPmi9rARPhuQPq61vkFpsrPwN2
AxkG7IQANNJh4bII6/+xBpSjmtInm0BQhxuojpHIYGiZvdHNYMrJfwFcAoVWfVvl
b9MtG9Qz
=rP0b
-----END PGP SIGNATURE-----
Merge tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two fixes for stable, one that had dependency on earlier patch in this
merge window and can now go in, and a perf improvement in SMB3 open"
* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
cifs: flush before set-info if we have writeable handles
smb3: optimize open to not send query file internal info
cifs: copy_file_range needs to strip setuid bits and update timestamps
CIFS: fix deadlock in cached root handling
The commit b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.
kernel BUG at drivers/iommu/iova.c:801!
Workqueue: kblockd blk_mq_run_work_fn
RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
Call Trace:
free_cpu_cached_iovas+0xbd/0x150
alloc_iova_fast+0x8c/0xba
dma_ops_alloc_iova.isra.6+0x65/0xa0
map_sg+0x8c/0x2a0
scsi_dma_map+0xc6/0x160
pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
scsi_queue_rq+0x79c/0x1200
blk_mq_dispatch_rq_list+0x4dc/0xb70
blk_mq_sched_dispatch_requests+0x249/0x310
__blk_mq_run_hw_queue+0x128/0x200
blk_mq_run_work_fn+0x27/0x30
process_one_work+0x522/0xa10
worker_thread+0x63/0x5b0
kthread+0x1d2/0x1f0
ret_from_fork+0x22/0x40
Fixes: b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.
Switch hexagon to use generic version of these functions.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
to test and use this feature in the NTB transport layer. Also, bug
fixes for the AMD and Switchtec drivers, as well as some general
patches.
-----BEGIN PGP SIGNATURE-----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=P1lR
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.3' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@2000: 'clocks' is a required property
Add the missing 'clocks' properties to the examples to fix the errors.
Fixes: 2c9239c125f0 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
With the conversion to DT schema, the examples are now compiled with
dtc. The ad7124 binding example has the following warning:
Documentation/devicetree/bindings/iio/adc/adi,ad7124.example.dts:19.11-21: \
Warning (reg_format): /example-0/adc@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
There's a default #size-cells and #address-cells values of 1 for
examples. For examples needing different values such as this one on a
SPI bus, they need to provide a SPI bus parent node.
Fixes: 26ae15e62d3c ("Convert AD7124 bindings documentation to YAML format.")
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Now that examples are validated against the DT schema, a typo in
avia-hx711 example generates a warning:
Documentation/devicetree/bindings/iio/adc/avia-hx711.example.dt.yaml: weight: 'avdd-supply' is a required property
Fix the typo.
Fixes: 5150ec3fe125 ("avia-hx711.yaml: transform DT binding to YAML")
Cc: Andreas Klinger <ak@it-klinger.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The schema examples are now validated against the schema itself. The
AST2500 pinctrl schema has a couple of errors:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
example-0: $nodename:0: 'example-0' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
pinctrl: aspeed,external-nodes: [[1, 2]] is too short
Fixes: 0a617de16730 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
The Aspeed pinctl schema have errors in the 'compatible' schema:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2400-pinctrl', 'aspeed', 'g4-pinctrl'] has non-unique elements
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2500-pinctrl', 'aspeed', 'g5-pinctrl'] has non-unique elements
Flow style sequences have to be quoted if the vales contain ','. Fix
this by using the more common one line per entry formatting.
Fixes: 0a617de16730 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Fixes: 07457937bb5c ("dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Matching on the 'cpus' node was a bad choice because the schema is
incorrectly applied to non-RiscV cpus nodes. As we now have a common cpus
schema which checks the general structure, it is also redundant to do so
in the Risc-V CPU schema.
The downside is one could conceivably mix different architecture's cpu
nodes or have typos in the compatible string. The latter problem pretty
much exists for every schema.
Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Properties which are child node definitions need to have an explict
type. Otherwise, a matching (DT) property can silently match when an
error is desired. Fix this up tree-wide. Once this is fixed, the
meta-schema will enforce this on any child node definitions.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-spi@vger.kernel.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull more input updates from Dmitry Torokhov:
- Apple SPI keyboard and trackpad driver for newer Macs
- ALPS driver will ignore trackpoint-only devices to give the
trackpoint driver a chance to handle them properly
- another Lenovo is switched over to SMbus from PS/2
- assorted driver fixups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - fix a mismatch between a condition check and its comment
Input: psmouse - fix build error of multiple definition
Input: applespi - remove set but not used variables 'sts'
Input: add Apple SPI keyboard and trackpad driver
Input: alps - don't handle ALPS cs19 trackpoint-only device
Input: hyperv-keyboard - remove dependencies on PAGE_SIZE for ring buffer
Input: adp5589 - initialize GPIO controller parent device
Input: iforce - remove empty multiline comments
Input: synaptics - fix misuse of strlcpy
Input: auo-pixcir-ts - switch to using devm_add_action_or_reset()
Input: gtco - bounds check collection indent level
Input: mtk-pmic-keys - add of_node_put() before return
Input: sun4i-lradc-keys - add of_node_put() before return
Input: synaptics - whitelist Lenovo T580 SMBus intertouch
Fix various regressions:
- force unencrypted dma-coherent buffers if encryption bit can't fit
into the dma coherent mask (Tom Lendacky)
- avoid limiting request size if swiotlb is not used (me)
- fix swiotlb handling in dma_direct_sync_sg_for_cpu/device
(Fugang Duan)
-----BEGIN PGP SIGNATURE-----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=Bv+Q
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions:
- force unencrypted dma-coherent buffers if encryption bit can't fit
into the dma coherent mask (Tom Lendacky)
- avoid limiting request size if swiotlb is not used (me)
- fix swiotlb handling in dma_direct_sync_sg_for_cpu/device (Fugang
Duan)"
* tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device
dma-direct: only limit the mapping size if swiotlb could be used
dma-mapping: add a dma_addressing_limited helper
dma-direct: Force unencrypted DMA under SME for certain DMA masks
Pull x86 fixes from Thomas Gleixner:
"A set of x86 specific fixes and updates:
- The CR2 corruption fixes which store CR2 early in the entry code
and hand the stored address to the fault handlers.
- Revert a forgotten leftover of the dropped FSGSBASE series.
- Plug a memory leak in the boot code.
- Make the Hyper-V assist functionality robust by zeroing the shadow
page.
- Remove a useless check for dead processes with LDT
- Update paravirt and VMware maintainers entries.
- A few cleanup patches addressing various compiler warnings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Prevent clobbering of saved CR2 value
x86/hyper-v: Zero out the VP ASSIST PAGE on allocation
x86, boot: Remove multiple copy of static function sanitize_boot_params()
x86/boot/compressed/64: Remove unused variable
x86/boot/efi: Remove unused variables
x86/mm, tracing: Fix CR2 corruption
x86/entry/64: Update comments and sanity tests for create_gap
x86/entry/64: Simplify idtentry a little
x86/entry/32: Simplify common_exception
x86/paravirt: Make read_cr2() CALLEE_SAVE
MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
x86/process: Delete useless check for dead process with LDT
x86: math-emu: Hide clang warnings for 16-bit overflow
x86/e820: Use proper booleans instead of 0/1
x86/apic: Silence -Wtype-limits compiler warnings
x86/mm: Free sme_early_buffer after init
x86/boot: Fix memory leak in default_get_smp_config()
Revert "x86/ptrace: Prevent ptrace from clearing the FS/GS selector" and fix the test
Pull perf tooling updates from Thomas Gleixner:
"A set of perf improvements and fixes:
perf db-export:
- Improvements in how COMM details are exported to databases for post
processing and use in the sql-viewer.py UI.
- Export switch events to the database.
BPF:
- Bump rlimit(MEMLOCK) for 'perf test bpf' and 'perf trace', just
like selftests/bpf/bpf_rlimit.h do, which makes errors due to
exhaustion of this limit, which are kinda cryptic (EPERM sometimes)
less frequent.
perf version:
- Fix segfault due to missing OPT_END(), noticed on PowerPC.
perf vendor events:
- Add JSON files for IBM s/390 machine type 8561.
perf cs-etm (ARM):
- Fix two cases of error returns not bing done properly: Invalid
ERR_PTR() use and loss of propagation error codes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
perf version: Fix segfault due to missing OPT_END()
perf vendor events s390: Add JSON files for machine type 8561
perf cs-etm: Return errcode in cs_etm__process_auxtrace_info()
perf cs-etm: Remove errnoeous ERR_PTR() usage in cs_etm__process_auxtrace_info
perf scripts python: export-to-postgresql.py: Export switch events
perf scripts python: export-to-sqlite.py: Export switch events
perf db-export: Export switch events
perf db-export: Factor out db_export__threads()
perf script: Add scripting operation process_switch()
perf scripts python: exported-sql-viewer.py: Use new 'has_calls' column
perf scripts python: exported-sql-viewer.py: Remove redundant semi-colons
perf scripts python: export-to-postgresql.py: Add has_calls column to comms table
perf scripts python: export-to-sqlite.py: Add has_calls column to comms table
perf db-export: Also export thread's current comm
perf db-export: Factor out db_export__comm()
perf scripts python: export-to-postgresql.py: Export comm details
perf scripts python: export-to-sqlite.py: Export comm details
perf db-export: Export comm details
perf db-export: Fix a white space issue in db_export__sample()
perf db-export: Move export__comm_thread into db_export__sample()
...
Pull core fixes from Thomas Gleixner:
- A collection of objtool fixes which address recent fallout partially
exposed by newer toolchains, clang, BPF and general code changes.
- Force USER_DS for user stack traces
[ Note: the "objtool fixes" are not all to objtool itself, but for
kernel code that triggers objtool warnings.
Things like missing function size annotations, or code that confuses
the unwinder etc. - Linus]
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
objtool: Support conditional retpolines
objtool: Convert insn type to enum
objtool: Fix seg fault on bad switch table entry
objtool: Support repeated uses of the same C jump table
objtool: Refactor jump table code
objtool: Refactor sibling call detection logic
objtool: Do frame pointer check before dead end check
objtool: Change dead_end_function() to return boolean
objtool: Warn on zero-length functions
objtool: Refactor function alias logic
objtool: Track original function across branches
objtool: Add mcsafe_handle_tail() to the uaccess safe list
bpf: Disable GCC -fgcse optimization for ___bpf_prog_run()
x86/uaccess: Remove redundant CLACs in getuser/putuser error paths
x86/uaccess: Don't leak AC flag into fentry from mcsafe_handle_tail()
x86/uaccess: Remove ELF function annotation from copy_user_handle_tail()
x86/head/64: Annotate start_cpu0() as non-callable
x86/entry: Fix thunk function ELF sizes
x86/kvm: Don't call kvm_spurious_fault() from .fixup
x86/kvm: Replace vmx_vmenter()'s call to kvm_spurious_fault() with UD2
...
