Fix wording based on checkpatch.pl
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
E.g. pm_runtime_set_active must be called while the power
management system is disabled. Fixes extra hanging clk_enable.
Signed-off-by: Topi Kuutela <topi.kuutela@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not print error in case of EPROBE_DEFER.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Under certain conditions, Cadence's I2C controller's transfer_size
register will roll over and generate invalid read transactions. Before
this change, the ISR relied solely on the RXDV bit to determine when to
write more data to the user's buffer. The invalid read data would cause
overruns, smashing stacks and worse.
This change stops the buffer writes to the requested boundary and
reports the error. The controller will be reset so normal transactions
may resume.
Signed-off-by: Alex Williams <alex.williams@ni.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> # in a seperate mail
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for Intel Comet Lake PCH-V which is based on Intel Kaby
Lake. Difference between it and other Comet Lake variants is that former
uses previous iTCO version 4 and latter use version 6 like Intel Cannon
Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In I2C there is no such thing as a "stop bit". Use the proper naming: "stop
condition".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In smbus-protocol.rst we use the text "Implemented by" for the same meaning
as "This corresponds to". Change everything to "Implemented by" for
coherency.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some of the section names are not very clear. Reading those names in the
index.rst page does not help much in grasping what the content is supposed
to be.
Rename those sections to clarify their content, especially when reading
the index page.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a monospace (literal) formatting for better readability of sysfs
attributes and the "dummy" client name. This looks much more readable in
ReST-generated output.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This section applies only to code for very old kernels. Avoid people
reading this unnecessarily.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use ReST syntax so that a proper hyperlink is generated.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a monospace (literal) formatting for better readability of sysfs
attributes.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Among the "static" instantiation methods the "board file" method is
described first. Move it as last, since it is being replaced by the other
methods.
Also fix subsubsection heading syntax and remove the "Method 1[abc]"
prefix as the subsubsection structure clarifies the logical hierarchy.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use ReST syntax so that a proper hyperlink is generated.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clarify from the beginning what these transactions are, and specifically
how they differ from the SMBus counterparts, i.e. the lack of a Count byte.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The subject is plural, fix the verb.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This clarifies these are functions (and would/will adds a hyperlink to the
function documentation if/when documented).
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hyperlinks from function names are not generated in headings. Move them in
the plain text so they are rendered as clickable hyperlinks.
While there also remove an unneeded colon in a heading.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the proper ACK and NACK naming from the I2C specification instead of
"accept" and "reverse accept".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These colons are not needed: the columns already nicely separate the
symbols from their description. They are also inconsistently preceded by
whitespace.
Remove the colons completely to simplify and clean up.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In I2C there is no such thing as a "start bit" or a "stop bit". Use the
proper naming: "start condition" and "stop condition".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the proper ReST syntax to generate a valid hyperlink.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the proper ACK and NACK naming from the I2C specification instead of
"accept" and "reverse accept".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These colons are not needed: the columns already nicely separate the
symbols from their description. They are also inconsistently preceded by
whitespace.
Remove the colons completely to simplify and clean up.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In I2C there is no such thing as a "start bit" or a "stop bit". Use the
proper naming: "start condition" and "stop condition".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This clarifies these are functions and adds a hyperlink to the function
documentation.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"I2C transfer" is a legitimate english sentence, no need for a hyphen
between the two words, as as such it is used in most of the
documentation. Remove the hyphen in the few places where it is present.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Uppercase "I2C" is used almost everywhere in the docs, but the lowercase
version "i2c" is used somewhere. Use the uppercase form consistently.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This section, partly dating back to the pre-git era, is somewhat
unclear and partly incorrect. Rewrite it almost completely including a
reference figure, concise but precise definition of each term and the
paths where drivers are found. Particular care has been put in clarifying
the relation between adapter and algorithm, which has no correspondence
in the I2C spec terminology.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- state the "official" name (I²C, not I2C, according to the spec) at
the beginning but keep using the more practical I2C elsewhere
- mention some known different names
- add link to the specification document
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The index page currently lists sections in alphabetical file order without
caring about their content. Sort sections based on their content logically,
according to the following structure:
* Intro to I2C/SMBus and their usage in Linux: summary, i2c-protocol,
smbus-protocol, instantiating-devices, busses/index, i2c-topology,
muxes/i2c-mux-gpio
* Implementing drivers: writing-clients, dev-interface,
dma-considerations, fault-codes, functionality
* Debugging: gpio-fault-injection, i2c-stub
* Slave I2C: slave-interface, slave-eeprom-backend
* Advanced: ten-bit-addresses
* Obsolete info: upgrading-clients, old-module-parameters
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- minor maintenance: update the license tag, sort headers
- move support for the write-protect pin into nvmem core
- add a reference to the new wp-gpios property in nvmem to at25 bindings
- add support for regulator and pm_runtime control
-----BEGIN PGP SIGNATURE-----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=jh24
-----END PGP SIGNATURE-----
Merge tag 'at24-updates-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.6
at24 updates for linux v5.6
- minor maintenance: update the license tag, sort headers
- move support for the write-protect pin into nvmem core
- add a reference to the new wp-gpios property in nvmem to at25 bindings
- add support for regulator and pm_runtime control
There is a statement that is indented one level too deeply, remove
the extraneous tab.
Fixes: b4c119dbc300 ("i2c: xiic: Add timeout to the rx fifo wait loop")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a spelling mistake in a module parameter description.
Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although in the most platforms, the power of eeprom are alway
on, some platforms disable the eeprom power in order to meet
low power request. This patch add the pm_runtime ops to control
power to support all platforms.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
[Bartosz: rebased on top of current at24/for-next]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In some platforms, they disable the power-supply of eeprom due
to power consumption reduction. This patch add vcc-supply property.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Update the help text to reflect current support devices:
1. The Exynos high speed I2C driver supports Exynos5 (ARMv7), Exynos5433
and Exynos7 (both ARMv8) SoCs,
2. The S3C I2C driver supports S3C, S5Pv210 and Exynos{3,4,5} SoCs.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some of the I2C bus drivers can be compile tested to increase build
coverage. This requires also:
1. Adding dependencies on COMMON_CLK for BCM2835 and Meson I2C
controllers,
2. Adding 'if' conditional to 'default y' so they will not get enabled
by default on all other architectures,
3. Limiting few compile test options to supported architectures (which
provide the readsX()/writesX() primitives).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[wsa: revert chunk for ZX2967. it needs more preparation]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The recommendation is that the set_active should be done
with pm runtime disabled.
Also fix the remove path for clocking.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It's not always the case that clock is already available when i2c
driver get probed at the first time, e.g. the clock is provided by
clock wizard which may be probed after i2c driver. So let's defer
the probe when devm_clk_get() call fails and give it chance to
try later.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add timeout to the rx fifo empty wait loop. Also check for the return
value for xiic_reinit and pass it to xiic_start_xfer.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
size_t should be printed with its own format to be 64-bit friendly and
fix warning when compiling on 64-bit platform (e.g. with COMPILE_TEST):
drivers/i2c/busses/i2c-highlander.c: In function ‘highlander_i2c_smbus_xfer’:
drivers/i2c/busses/i2c-highlander.c:325:22: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pnx.c: In function ‘i2c_pnx_probe’:
drivers/i2c/busses/i2c-pnx.c:737:47: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 5 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pmcmsp.c: In function ‘pmcmsptwi_probe’:
drivers/i2c/busses/i2c-pmcmsp.c:276:25: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 3 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_new_device is deprecated, use i2c_new_client_device. Also, align a
paragraph while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_new_device is deprecated, use i2c_new_client_device.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
