Handle DCS-AWGN event and take actions accordingly:
For STA mode, if the interference locates on primary 20MHz,
disconnect from AP; otherwise, find a max interference free width
and trigger channel change.
For SAP mode, if the interference locates on primary 20MHz,
try to select a random interference free channel and trigger channel
change (stop SAP if no channel is selected); otherwise, find a max
interference free width and trigger channel change.
Change-Id: I33e79f454b459b12ad84f8b0f3259403037464ee
CRs-Fixed: 2958675
Extend hdd_config_modulated_dtim() to configure moddtim
dynamically in the both non li offload and li offload mode.
Change-Id: I8669ec618d4aa9cd87c4c234972ca500c98119b6
CRs-Fixed: 2970090
Add function to populate the rx average rssi received from target in
pkt_capture vdev_priv structure. The rx average rssi is received in
wmi smart monitor event.
Change-Id: I9206669b418a2245bb8d53920040fddea77ce06c
CRs-Fixed: 2969242
Register handler for wmi smart monitor event in packet capture
mode in lithium. Currently, wmi smart monitor event provides
average rssi of last ten received data packets.
Change-Id: Ieeea5cbef328b04f139f54e7a42d52a3cf25824b
CRs-Fixed: 2969245
Currently the 6G edge channel feature is MCC specific.
Make the 6G edge channel feature common for WIN and MCC.
Change-Id: I723b6db1d74dca5a911eede4ec6e6167f6b3e6bc
CRs-Fixed: 2976871
This reverts change-id I176b9c09106cc0d7f5cfbc474912e4a48d633ff2.
The 0 count chan avoid event is used to clear all previous reported
chan avoid freq range, so it can't be skipped.
Change-Id: Ie01d88c353a7f71bbee70ae67f54147ea147f6d4
CRs-Fixed: 2970061
Return success when firmware doesn't support 11k offload, or else
subsequent roaming related wmi commands have no chance to issue.
Change-Id: I69d55cca63f2b7ab4787295a2825159395cf2a11
CRs-Fixed: 2976163
Provide ucfg api to configure qos null and trigger frames.
Ucfg api will send configuration to FW. Below configuration values
are allowed.
PACKET_CAPTURE_CONFIG_TRIGGER_QOS_DISABLE: disable capture for
trigger and qos frames.
PACKET_CAPTURE_CONFIG_TRIGGER_ENABLE: enable capture for trigger
frames only.
PACKET_CAPTURE_CONFIG_QOS_ENABLE: enable capture for qos frames only.
PACKET_CAPTURE_CONFIG_TRIGGER_QOS_ENABLE: enable capture for both
trigger and qos frames.
The packet capture config old value will be over written by new value.
For example, first if we configure value as
PACKET_CAPTURE_CONFIG_TRIGGER_ENABLE and then if we send config as
PACKET_CAPTURE_CONFIG_QOS_ENABLE then config is enabled only for qos.
Change-Id: I02dcd4372c7194ec3e477694ad0e2c045fe6c942
CRs-Fixed: 2967824
Add parameter 'bool sync' for wlan_cfg80211_crypto_add_key()
to indicate whether or not to add key synchronously.
If it's set to true, wait until install key complete event
is received.
Change-Id: I9a69d486665fb3f65a5720ccfbfb638c09329418
CRs-Fixed: 2865832
Add mcs rate, gI type and other SU sig info to cfr metadata.
For Tx based capture mcs rate & gI type is applicable
MCS For legacy mode
0: 48 Mbps
1: 24 Mbps
2: 12 Mbps
3: 6 Mbps
4: 54 Mbps
5: 36 Mbps
6: 18 Mbps
7: 9 Mbps
8: invalid entry
MCS for HT, 0-7: MCS0-MCS7,
MCS for VHT, 0-9: MCS0-MCS9,
MCS for HE, 0-11 MCS0-MCS11, 12-13: 4096QAM
GI:
0: 0.8 us
1: 0.4 us
2: 1.6 us
3: 3.2 us
ltf_size:
0: he_ltf_1_x
1: he_ltf_2_x
2: he_ltf_4_x
dcm: Indicates if DCM set
0: No DCM
1: DCM
sgi: Indicates if short gI used
0: No short gI
1: short gI
beamformed: Is packet beamformed
0: non-beamformed
1: beamformed
stbc: Indicates if stbc applied
0: No STBC
1: STBC
Coding:
0: BCC
1: LDPC
Change-Id: If6ab4b4878ab24406aba0e890ec08a2dae2b4634
Firmware sends NAN log events to driver and these are logged
with info level to capture complete NAN state machine logs in kmsg.
Currently, these events are received/processed in soft IRQ context
and causes performance issues as logs introduce delays. Move the
event registration to RX_WORK context to avoid delays.
Change-Id: I15ba20059f55f002cfe276d62e68e3cc09136a23
CRs-Fixed: 2960359
Existing INI disable_4way_hs_offload is defined as a boolean
that controls the EAPOL Handshake to be offloaded to Firmware or
Not. There is no way to specify the EAPOL offload per AKM.
Hence extended the support of EAPOL handshake offload to firmware
per AKM by converting this INI to a bitmap integer.
With ini value as 0 by default Firmware takes care of 4-way HS
during roam for all AKMs except for SAE and OWE. If
this ini value is 1 then Host takes care of EAPOL for all AKMs.
Having the backward compatibility, added a new value to ini.
If this ini value is set to 2 and also if the SAE EAPOL offload
service bit is set by Firmware then the behavior is same as ini
with 0 except that Firmware takes care of 4-way HS for SAE roam
as well. And for OWE it is still handled by supplicant.
To achieve this, new roam offload flag is introduced to indicate
Firmware about SAE roam EAPOL offload, So that in Roam sync
indication Firmware will inform the status as connected but not
authenticated so that supplicant can take care of 4-way EAPOL HS.
Change-Id: I8b65a1768fad91fac7e427712d3ccf4586176f5f
CRs-Fixed: 2955029
Currently, cp stats are received through kworker thread context.
This causes race conditions/out of sync issues if any common data
structures are handled in parallel in scheduler thread context.
There is no need to receive the cp stats on kworker thread as per
current design. So, move the cp stats event handling to scheduler
thread to avoid any race conditions.
Change-Id: Id8134003e6f7a3e0368b20c496f650e0b7025b9e
CRs-Fixed: 2928876
Fix the compilation error post movement of CFR files to
cmndev and rename cfr init deinit APIs to be chip
independent. Also port fixes from component_dev.
CRs-Fixed: 2938886
Change-Id: I2f5637f5717ce5154e3b642c3ade646794e99602
Move CFR to common project and rename the files as it will
be shared with other targets as well. Fix checkpatch errors
too.
Change-Id: I66481848036212aedab74c9c18848070ac1a3511
When obss scan is enabled, FW will trigger scan periodically by
a timer. If a scan was triggered, FW need to access host memory
for data transfer. Occasionally, suspend may happen during one
scan, then FW is unable to access host memory and fw will crash.
So disable the obss scan before suspend.
Change-Id: Ie507da929a3701473cb57888e96e702e34d4c95a
CRs-Fixed: 2927239
When host failed to find out vaddr by paddr from FW, output more
information for debug further.
Change-Id: I65c4965c12c2ffa3fe2a26a82df01d1b91501c73
CRs-Fixed: 2925194
Driver gets vdev by wlan_objmgr_pdev_get_first_vdev and returns wrong
vdev in some platforms, and then gets wrong channel/phy_mode. This
change gets vdev by id and fix this issue.
Change-Id: I814d516361238afbd0345bc362c286d1cb55a7d4
CRs-Fixed: 2933525
Separate the common fields of csi_cfr_header and update
the logic of calculating the cfr_metadata_len.
Move cmn header update code to single place.
CRs-Fixed: 2916901
Change-Id: I97d99df45f667f4ed3b80264b12d3d09a3bcae95
Sometimes firmware sends spectral events repeatedly with
wrong vdev. This causes continuous error logs are
written to kmsg.
Replace info prints in target_if_consume_spectral_report_gen3()
with debug level prints.
Change-Id: I2ca4be7d0d13e841a6dbd4efbc02ecd2b12893f8
CRs-Fixed: 2926759
Agile scans (preCAC/RCAC) use the Agile Engine which is also needed
for the Agile spectral scan. Hence, both cannot run at the same time.
Currently, if Agile preCAC is enabled, Agile spectral scan is not
started. Do not start the spectral scan if either RCAC is enabled or
preCAC is enabled.
Change-Id: I242c28c2c3f8872ceab6314dde80361c283d3ac1
CRs-Fixed: 2922250
In the issue reported, the clear stats request from the
user space is timing out because event id from firmware is not received.
From the logs it is not clear whether host driver received it or dropped
it in the error path.
Add debug logs, to make sure cp_stats event id is received in the host
driver and also in error cases.
Change-Id: I634714281db4a82826791725ec38fd589334cde8
CRs-Fixed: 2926978
When agile spectral frequency is 0 and user tries to start agile spectral
scan, 'A parameter is not initialized' message is thrown from user space
but that message is not enough to identify that agile spectral frequency
is not initialized. To address this, print an error message from driver
when Agile spectral frequency is 0.
CRs-Fixed: 2921000
Change-Id: Ibbb144a57774ad274b31015c7a04aa6097daf09f
The regulatory wireless modes are populated by FW in
wlan_psoc_hal_reg_capability during service ready. This is copied
to the host regulatory data structure reg_cap. To accommodate the
802.11BE wireless modes, data type of wireless_modes in reg_cap is
changed from uint32_t to uint64_t, though FW still advertises as a 32
bit flag. As the wireless mode data type of host and FW are different,
structure copy using qdf_mem_copy does not work as expected and it corrupts
the adjacent elements.
Hence copy the elements individually from wlan_psoc_hal_reg_capability
to wlan_psoc_host_hal_reg_capabilities_ext structure. Also, typecast the
wireless_modes to 64 bit before storing in the host structure.
CRs-Fixed: 2901260
Change-Id: I42c8de831f97ec691c9b8cb50b8982662e39e7d9
Extract the 11BE flags advertised by FW in WMI_SERVICE_READY_EXT2_EVENTID
and update the regulatory pdev wireless modes. The wireless mode is
currently represented as 'uint32_t' and all the 32 bits are exhausted.
To accommodate the new 11BE flags, change the data type of wireless_modes
from 'uint32_t' to 'uint64_t'.
Add a regulatory phymode 'REG_PHYMODE_11BE' in enum reg_phymode.
If the chip does not support 11BE phymode, FW advertises it via
WMI_REGULATORY_PHYBITMAP enum with a value of REGULATORY_PHYMODE_NO11BE.
Extract the phybitmap and store it in the regualtory
as 'REGULATORY_PHYMODE_NO11BE' bitmap.
CRs-Fixed: 2901260
Change-Id: I4ed3fc7c907b1f76e59efb347c747acea2a163b0
offload igmp feature to fw in case of suspended state
to avoid high power consumption.
Change-Id: I05fbf23dc2836f8f5dc6e2f45b35bf2d30c39790
CRs-Fixed: 2907644
Updated the EHT related variables as per latest fw cmn headers.
Address review comments from previous EHT gerrits.
Change-Id: I67cd58a4efcf3e06d2ca3b5570432593b1d80825
CRs-Fixed: 2902607
In agile spectral scan scenario, if there is a chan switch,
it is possible for the new operating span to overlap with
the agile frequency, which results in erroneous outcome.
Make agile center freq 0 as part of every stop agile
scan. This ensures that a new frequency is mandated
as part of every agile scan.
Change-Id: I4531aa0636a62b918bace66098c2c287e72d55d3
CRs-Fixed: 2910449
EHT capapilities will be received as part of ext2 service ready message.
Update the structure as per firmware common header file and extract the
EHT capabilities field.
Change-Id: Id2dd170db4de588008742f95493d4d06a6431f1c
CRs-Fixed: 2857802
Add check to drop the avoid channel list event if the range count is 0
since it would not affect the channel list anyways.
Also, add the rate limited debug print for the target_if module.
Change-Id: I176b9c09106cc0d7f5cfbc474912e4a48d633ff2
CRs-fixed: 2909614
Change the get_target_if_spectral_handle_from_pdev() api to
non-inline for code size reduction.
CRs-Fixed: 2896467
Change-Id: Icb92643a9c0d85a1b4328cd0c516d6d771877a4f
In target_if_register_mgmt_data_offload_event(), check NULL value of
wmi_handle before it's used by wmi_service_enabled()
Change-Id: Iea51c59770258fd10468bb439f559094b563851f
CRs-Fixed: 2900533
target_if_dump_fft_report_gen3() function doesn't check if the FFT report
is present in the Spectral report. Add the report mode 0 check to avoid
printing FFT report when it is not there.
Change-Id: Ia825cd7927ec7ffa41473649d381c717b0ef26c9
CRs-Fixed: 2898904
Enable lower 6G edge channel ch2 (5935MHz) for APL2 6G regdmn
using a service bit WMI_SERVICE_ENABLE_LOWER_6G_EDGE_CH_SUPP,
which is not enabled by default.
Also, disable upper 6G edge channel (7115MHz) using another
service bit WMI_SERVICE_DISABLE_UPPER_6G_EDGE_CH_SUPP, that
is enabled by default.
Change-Id: Ia7cb7f7d3165375178adbe70adb19b8671496b6d
CRs-Fixed: 2885623
Add vendor command interface/feature through which the user
or vendor can set the dtim count as per their requirement.
Change-Id: I26010948c4ed7e3c49bfe0453119235d4f438c6f
CRs-Fixed: 2894349
In order to support different power levels of 6G AP and client,
the channel list event from FW namely "REG_CHAN_LIST_CC_EVENTID"
is modified to add few parameters specific to 6GHZ devices.
Hence the existing event is replaced by REG_CHAN_LIST_CC_EVENT_EXT for
all 2G/5G/6G pdevs in FW. Therefore, after the service ready event, FW
sends the channel list for the configured country/regdomain via
REG_CHAN_LIST_CC_EVENT_EXT. This mandates that all host software need
to have the processing capability of REG_CHAN_LIST_CC_EVENT_EXT to bring
up the AP.
As there can be host software which has not yet implemented the
version of "REG_CHAN_LIST_CC_EVENT_EXT", backward compatibility is lost
if "ONLY REG_CHAN_LIST_CC_EVENT_EXT" is sent by FW.
Hence a 3 way handshake between host and FW is established.
1. FW advertises its capability of processing REG_CHAN_LIST_CC_EVENT_EXT
id via wmi service bit 'wmi_service_reg_cc_ext_event_support'.
2. If the host is capable of processing the "REG_CHAN_LIST_CC_EVENT_EXT"
event id (which is done based on registration of this event), host
sends the capability in WMI_INIT_CMDID setting a bit in host_service_flags.
3. Based on host capability advertised in WMI_INIT_CMDID, FW decides to
send the old event ("REG_CHAN_LIST_CC_EVENTID") or the new event
("REG_CHAN_LIST_CC_EVENT_EXT").
4. If there is no flag indicated by host to FW in WMI_INIT_CMDID, FW
by default sends the old event ("REG_CHAN_LIST_CC_EVENTID").
CRs-Fixed: 2876360
Change-Id: Ibe95f414ad9fff0e5641bcc6e60450ef9afe245b
For the minidump feature, the wlan_minidump_remove function
definition is modified. So, update the function parameters
accordingly at all instances of the wlan_minidump_remove function.
Change-Id: I5a346f6cdf423ece02fb08d68e4422251af54876
CRs-Fixed: 2860435
Fix the wmi command id is not right issue for
enable/disable periodic peer CFR capture if
ENABLE_HOST_TO_TARGET_CONVERSION not enabled.
Change-Id: I82ba6c781f67aa73f373a0a914838f482d86f165
CRs-Fixed: 2865389
Fix compilation errors when DIRECT_BUF_RX_ENABLE compile-time flag is
disabled.
Change-Id: I2bbce6eb8838ecab02b6462c1c0ee28877accdb4
CRs-Fixed: 2883310
Reset the 160 MHz state machine on any error
while processing a Spectral report.
CRs-fixed: 2879610
Change-Id: I982d12edc5c9aa24b0255fbcb932d198a6da514b
For WIN, a specific raw event handler is used for handling
WMI_CTRL_PATH_STATS_EVENTID received from FW.
As a part of control path stats infrastructure, event handler
for WMI_CTRL_PATH_STATS_EVENTID is different and this results
in wifistats functionality break for WIN side.
Make changes to use WIN specific event handler.
Change-Id: I2ac677c3ca55cd783734d1137c39b8ee1d5dcbf5
CRs-Fixed: 2878466
The host will send TPC power to FW via the new WMI cmd
WMI_VDEV_SET_TPC_POWER_CMDID going forward instead of
WMI_VDEV_PARAM_TX_PWRLIMIT to accommodate 6GHz channels.
But, to support backward compatibility for New Host+old FW
the TPC power will be sent to FW via legacy WMI cmds
WMI_VDEV_SET_PARAM_CMDID (during initial connection) or
WMI_VDEV_PARAM_TX_PWRLIMIT (power value change during RRM
req/bcn processing from connected AP) with the help of a
service bit WMI_SERVICE_EXT_TPC_REG_SUPPORT.
Change-Id: I22e11ff847cd384fac8ea0061e5df42cea0c8de8
CRs-Fixed: 2874245
DBR srng details are not sent properly to F.W via WMI_DMA_CFG_REQ
msg, this leads to F.W accessing undefined address.
Fix this by passing DBR srng details properly.
Change-Id: I15b393ad809dc0757e3637558f0bddd05530149d
CRs-Fixed: 2861621
Add common target_if event handler for wmi_pdev_cp_fwstats_eventid
from the control path stats infrastructure of firmware and register
with the wmi.
CRs-Fixed: 2856380
Change-Id: Ia16e34c4dc1e12b817258c5e6d617a8cb560cf5b
TLV targets advertises the agile Spectral capability in the
chain mask table of extended service ready event.
For legacy targets, mac phy capabilities, which holds the
chain mask table is null. This leads to a load time crash
for some legacy platforms. To fix this, initialize
agile Spectral as disabled for the targets which doesn't
support extended service ready message.
CRs-Fixed: 2854348
Change-Id: I09a64259b31e3e5eb0441f35dbb9451dec001780
Following fields in the Spectral FFT report have been modified in the HW
in the version 2 of the Spectral report, reflect the same at the Host.
- fft_radar_check
- fft_peak_sidx
- fft_chn_idx
- fft_base_pwr_db
- fft_total_gain_db
CRs-Fixed: 2855909
Change-Id: I8dd190cae8da260d1fb639342ca980285bfd3d0e
Add sanity check for CFR payload length in case of QCA5018
before relaying CFR data buffers to user space.
Change-Id: I81f37bebd3b9372606906fc87ce8ee90fe4809a1
CRs-Fixed: 2855173
Bring down number of sub buffers in Relay FS from
470 to 255. Earlier 470 buffers were introduced to
maintain 2MB uniformity across platform for relayfs.
But, as IPQ5018 is 512M platform and having 255
buffers is sufficient enough to hold CFR data,
we have brought down the number to 255.
This saves 1MB memory.
Change-Id: Ibbd6926c6712b871e8174e44bd24abf703a8e736
CRs-Fixed: 2855173
Expose the API to send WMI_SET_TPC_POWER_CMDID within the target_if
module. Register the callback under tx_ops.
Change-Id: I1d075df717cff997e7ac85884fe587ed298cbb28
CRs-fixed: 2849695
Support has been added in common code to register both
common tx ops and MC/WIN specific tx ops. Add support to
register and tx ops for MC specific stats.
Change-Id: I4e5263e4685a707008ec3c5e96f50c707b071fe9
CRs-Fixed: 2851256
Add functions to handle the new WMI event,
WMI_REG_CHAN_LIST_CC_EXT_EVENTID. This includes processing new
data regarding standard power, low power indoor, and very low
power Clients and APs.
Process the regulatory rules from FW to populate the new 6G
channel lists. Fill in the current channel list with the
correct 6G master channel list. Copy other information from
the event into the regulatory private objects as needed.
Change-Id: I0c2001d809e4f0b292bac866780faa2850b1a8b1
CRs-fixed: 2799403
Currently there is no support to register both common cp stats
ops and MC specific cp stats ops. Add support to register common
ops and MC/WIN specific cp stats ops.
Change-Id: Ibaee9da8b1ce3185161821f2be751d8bb4bf10e2
CRs-Fixed: 2851235
In SAP on non DFS channel, there are double votes for PCIe
link down and later if there is PCIe link up, this counter
sends D3 WoW case instead of D0 WoW case to firmware.
To fix this, In vdev restart case, if SAP is on non DFS
channel and previously it was on DFS channel then vote
for PCIe link down and if SAP is on DFS channel and
previously it was on non DFS channel then vote for PCIe
link up. Also, the PCIe link down should be needed if
vdev stop response is for DFS channel.
Change-Id: I817ffceb482091b8d9c5441d80abb43b7d0f866b
CRs-Fixed: 2849706
Extract agc gain information, CFO & rx_start_ts from
rx status and cfr peer capture event to CFR host metadata
Change-Id: Id896554f1da6920bd3eeced1298b07857d41a68b
Return type of "target_if_is_spectral_active" and
"target_if_is_spectral_enabled" is bool. Wrong return values
are send for this APIs in case of errors.
CRs-Fixed: 2845250
Change-Id: I2344676a1ada51e041bb5f7acac8aa22847bee5c
If Spectral scan is disabled(agile and normal mode disabled)
skip init/deinit of Spectral module. Also avoid user requests
to configure/start/stop scan. If either agile or normal mode
is disabled block user requests for that mode alone.
CRs-Fixed: 2840335
Change-Id: I81148e5580fe4bf991b97cd086c8e3a9ca78e77d
Add utility APIs to check Spectral scan is disabled for
a given pdev/psoc/mode.
CRs-Fixed: 2840317
Change-Id: I6820cfc056c697434a138ddf9d8d93b5796a4722
Add APIs to init Spectral feature caps in the upper layer of the
Spectral module.
CRs-Fixed: 2840249
Change-Id: Idfb34a9eec3a66c6d193be7bb828eeec30548ae7
Add target if APIs to initialize normal and agile Spectral
feature caps for a pdev.
CRs-Fixed: 2840247
Change-Id: I6c5385c2050007a5ff3f668ab3d6176328294549
Add APIs to check the agile and normal Spectral scan
capability of the target. This information is derived from
the advertisements from halphy via WMI events.
CRs-Fixed: 2840227
Change-Id: I2aae79b3342d8d74a1f4c00e813cae843a71106a
Use the hal_srng APIs that handle byte-order conversion of ring pointers
for big-endian platforms.
Change-Id: I2664636d5d2a1abfd7b643ea4c4d63d328a9880f
CRs-Fixed: 2845047
Swap each word of key_data before sending key install command.
This is needed since copy engine swap is enabled for big endian platform
and key needs to be plumbed in network byte order for decoding to happen
correctly.
Handle the swap in wmi layer since all other big endian conversions are
handled in this layer.
Change-Id: Ia6f0d579f3edaf32193c353ea2fe35cc40f55399
Direct Buf Rx has a source ring to communicate with the target.
The target updates its tail pointer in little-endian format and this update
doesn't go through any byte-order conversion at the target. On a big-endian
Host platform, this tail pointer will be read in reverse order of bytes.
To fix this, convert the tail pointer to the Host order before using it.
Change-Id: Ibcaf3d7507910ea81eeb895772241ab9861ee45a
CRs-Fixed: 2843259
WLAN chip components are little-endian based. When such a chip is attached
to a big-endian Host platform, there will be a mismatch in the order of
bytes for the data that is transferred between the Host and target.
Spectral HW module transfers the Spectral report directly to the Host DDR.
This transfer doesn't go through any byte-order conversion at the HW side.
So, to avoid invalid reads at the Host side on a big-endian platform,
convert the Spectral report to the Host byte-order before using it.
Change-Id: I742537f3a95ffca2e12b83535e83e2870ad06b10
CRs-Fixed: 2838371
Periodically request pdev stats from FW to receive channel noise floor
information after monitor vdev has been brought up, based on the band
currently being sniffed. Use the band information as a secondary parameter
when sending periodic request to fw so a single noise floor value is sent
to host. Pass this noise floor information to dp_pdev to be populated in
radiotap header.
Change-Id: I488e4985392cb646ffdee914359fa995dbeb025e
CRs-Fixed: 2833458
Currently, Stats request commands are sent over qmi right from the
target suspend request is sent to FW. This is leading to a crash in
FW since it is trying to access PCI when it is in suspend state.
To address this, send stats request over QMI only after the ack is
received for the target suspend command.
Change-Id: I1b2b6a60c5d8c7ec4375d328e58a66d749794e3f
CRs-Fixed: 2835903
If module is not registered for dbr in any platform it
results into Null pointer dereference.
Added Sanity check to avoid Null pointer dereference for
cfg80211tool wifi0 g_dbr_ring_status.
Change-Id: I9e68dfc9d58d70693184f53913cd7f2324d788c1
FFT bin is 10-bit wide in Spectral pack-modes 0 and 1. However, HW packs
just one FFT bin in a 32-bit DWORD by adding extra padding bits in
pack-mode 0. Currently, the Host reads the entire 32-bit DWORD to figure
out the FFT bin value. Instead, read the only useful bytes i.e.,
least significant 2 bytes of a DWORD. This approach is efficient,
especially on a Host that implements a byte-swap mechanism on FFT bins on
a big-endian Host.
Also, while dumping FFT bins for debug purpose, print the first 2 bytes of
an FFT bin in pack-modes 0 and 1.
Change-Id: I20ca8c4905671e80251dca07f80ce17801b98f5c
CRs-Fixed: 2831530
Currently, host decrements beacon switch count and sends
channel switch frame every time until count becomes 0 this
may introduce sync issue between fw and host.
To avoid sync issue csa switch count is offloaded to fw. fw
will send CSA_SWITCH_COUNT_STATUS_EVENTID once beacon count
becomes 0 and host will send vdev restart once it recives
CSA_SWITCH_COUNT_STATUS_EVENTID.
Change-Id: I60238e8e83b56ca4c6490f9516d673d14ef9c323
CRs-Fixed: 2831356
WLAN chip components are little-endian based. When such a chip is attached
to a big-endian Host platform, there will be a mismatch in the order of
bytes for the data that is transferred between the Host and target.
Direct DMA framework writes 64-bit values to its DMA ring entries.
These DMA ring entries are present in the shared memory between the Host
and the FW and the data transfer doesn't go through any copy engine.
So, to avoid invalid reads at the FW side on a big-endian platform, write
ring entries in little-endian format so that the FW reads them correctly.
Change-Id: I9c9189f914fdda335723c25fc05484487985447c
CRs-Fixed: 2828746
check csa_beacon_template service and set
WLAN_SOC_CEXT_CSA_OFFLOAD/25th bit of
soc_fw_ext_caps in psoc if service is
supported by fw.
Change-Id: I8dca74c805cc8696f261e0f791818bca579c80c8
CRs-Fixed: 2826451
Use WMI_RX_SERIALIZER_CTX context for thermal event handler.
The default context is tasklet, it may cause issue when interact
with OS interface.
Change-Id: I349412c2afee9a081f0d38704541f77b5e4569f4
CRs-Fixed: 2824461
In function target_if_crypto_set_key(), array pn's size is 16,
while params.key_rsc_ctr's length is 8, so the length of src
buffer(params.key_rsc_ctr in this case) should be used when
copying data to dest buffer(pn).
Change-Id: Ifa9156963c3da0234dbf8755a4d1f7bf3b96d0ff
CRs-Fixed: 2822715
In mission mode, add support for virtual add/del monitor
mode interface. In addition to STA vdev, create and maintain
a new vdev for monitor interface.
Change-Id: I91ea8e56976cce92f9b1ae308d4bd0fb30815366
CRs-Fixed: 2818499
FFT bin values can span 10 bits for HKv1, HKv2 and Pine.
This change is to cap the values to 8 bits for such case
on these platforms.
Change-Id: I144b00b1ed21a3281f79050bb1ab63bd857e47b1
CRs-Fixed: 2804192
In Pine 160/165 MHz following are the expected sequence of events.
1. Start scan WMI command
2. FW param WMI event
3. Direct DMA completion WMI events
If 3 and 2 happens in the reverse order (i.e., host receives a direct
DMA completion event before receiving a FW param WMI event), host assert
will be triggered.
This change removes the assert and drops the Spectral reports till
FW param WMI event is received.
CRs-Fixed: 2812403
Change-Id: I537d0077737baab8d3a8e90bdc4f9138690010bc
Firmware advertises the service capability bit
WMI_SERVICE_SCAN_CONFIG_PER_CHANNEL when it supports per channel
scan config flags. Get this and cache in psoc.
If firmware supports WMI_SERVICE_SCAN_CONFIG_PER_CHANNEL, it uses
the upper-12 bits(bit-20 to bit 32) of channel_list for flags and
lower 20-bits(bit-0 to bit-19) for frequency. If firmware doesn't
support it, then channel_list holds the frequency value only.
Fill the flags and frequency accordingly.
Change-Id: I88a6f29f61e1ecea75bc5574cadcbbfbb7f8b188
CRs-Fixed: 2806405
Add API to get/set the target global mode when the driver
is loaded (or) dynamically switched between modes
Change-Id: I65857ef57a17645da94301e26c0daddc30c5ad79
CRs-Fixed: 2809955
Since new rso ROAM_OFFLOAD_V1 path is enabled, remove
the old rso path code for cm/wmi roam related files.
Change-Id: Iec350f032c3e037204f560199d4a6e258ac02688
CRs-Fixed: 2810145
Roaming between different PMF option APs has following issues:
1. Roaming between Optional -> Disabled -> Optional
When STA roam to optional, PMF is set to False from STA in reassoc
request and all management pkt not secured.
2. Roaming between Required -> Disabled -> Required
STA not able to find candidate AP when tried to roam to AP with PMF
Required.
Root cause: When LFR3 roam happens, vdev_crypto_params will be reset
including rsn_caps 11w PMF, if new AP hasn't enabled PMF, vdev rsn_caps
11w PMF is disabled too, and passed to F/W. Then F/W think DUT STA
doesn'tsupport PMF, then failed to roam to AP with PMF Required and
enabled.
Fix:
Get self-capability of 11w PMF from connected profile and pass to F/W in
WMI_ROAM_SCAN_MODE by wmi_fill_rso_tlvs after roaming.
Move target_if_cm_roam_fill_11w_params to csr_cm_roam_fill_11w_params,
put protocol part to csr connection manager.
Change-Id: I543799385ec8c0ec7afdf64e2310c24758305095
CRs-Fixed: 2807454
Move the resource configuration command after initializing
pdev wmi handle and just before wmi init command.
CRs-Fixed: 2801602
Change-Id: I3a476cbbccd5874c79cfa08f1252c728ebc9a5c6
Stats event from target might have several sub events, and some event
has no peer stats but have adv/ext2 peer stats.
Check ext/ext2 peer stats even no peer stats in
target_if_cp_stats_extract_peer_stats(). Fix copy adv stats size error
in tgt_mc_cp_stats_prepare_n_send_raw_station_stats(). Although
get_station_stats_cb and get_peer_stats_cb is union callbacks,
better to assign to get_station_stats_cb because it is for
TYPE_STATION_STATS.
Change-Id: I0bead0cbb8b549cc538ef4a7327f0a8303c90bd1
CRs-Fixed: 2801842
fft bin size adjust parameter is no longer applicable for
QCN9100. Remove QCN9100 in the check for setting this paramenter.
Change-Id: Ibff3d2d618e20563add79e65e31a442d8d36ba61
CRs-Fixed: 2804120
Handle firmware thermal stats event and populate the thermal
information to upper layer with vendor command event.
Change-Id: I83286367ab542c08a205a7636f3d03189b0500e5
CRs-Fixed: 2786623
Change return type of following APIs from int to QDF_STATUS.
wmi_unified_register_event()
wmi_unified_register_event_handler()
wmi_unified_register_raw_event_handler()
wmi_unified_unregister_event()
wmi_unified_unregister_event_handler()
Change-Id: I534b499edbcfec6eddea0e9ed48f9eb1a2e872c8
CRs-Fixed: 2791275
To discard 5G candidates based on RSSI threshold, Introduce
a new INI "min_rssi_for_2g_to_5g_roam" to configure the RSSI
for High RSSI Trigger.
Min: -120
Max: 0
Default: -70
Change-Id: If4545296ef1b53d18b8ae4abf12d450f5e690240
CRs-Fixed: 2789017
In the Rome IPA case, it need wlanhost side to
enble/disable intrabss by WMI_VDEV_PARAM_INTRA_BSS_FWD.
If set to 1, the ip data transfer between two wlan clients
should be:
wlan client1 -> wlan fw -> wlanhost -> wlan fw-> wlan client2.
If set to 0, the ip data transfer between two wlan cleints
should be:
wlan client1 -> wlan fw -> ipa -> wlan fw -> wlan clients2.
Change-Id: I105ddbdb58f2cd01bdf94521bd7934508889de5d
Host gets spectral scan data after stopped spectral scan, then it
can't find out current vdev since vdev id is reset when stopping
spectral scan.
Change-Id: I082b784e998a7600c7f8ef14bf67b790942f3a5f
CRs-Fixed: 2779397
Currently the roam scan scheme for each trigger is hardcoded to
either full scan or partial scan followed by full scan. Based on
the new requirement for home scenario,the user space configures
roam scan scheme for various triggers. Add support to send scan
scheme type for indvidual roam triggers enabled from userspace.
The default value of roam scan scheme can be modifed for
below roam triggers:
WMI_ROAM_TRIGGER_REASON_PER,WMI_ROAM_TRIGGER_REASON_BMISS,
WMI_ROAM_TRIGGER_REASON_LOW_RSSI,WMI_ROAM_TRIGGER_REASON_BSS_LOAD,
WMI_ROAM_TRIGGER_REASON_BTM
Change-Id: If8b185897b813afc44af362d31172705ea4d7b5c
CRs-Fixed: 2785233
QCA6490 expects twt_ap_pdev_count 2, to bring up twt sap on 2g.
Currently twt_ap_pdev_count is derived from num of radios and is
1 in case of MCC.
Configure twt_ap_pdev_count value equal to number of phy
advertised by firmware in wmi service ready ext event, configure
under flag WLAN_TWT_AP_PDEV_COUNT_NUM_PHY if defined in kbuild
Change-Id: Ib3fa81d140b473daa253e32cde2e11aad1b78b4d
CRs-Fixed: 2786512
User sends wfa test configs to host using vendor command
QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Host parses the
vendor command and sends wfa test configs to FW using WMI command
i.e. WMI_WFA_CONFIG_CMDID
Change-Id: I5aa0bc8b0a0064828b48368e47d53a5ad5e7ff2f
CRs-Fixed: 2772013
Add vdev id in RSO stop commands to make sure that command is sent
for proper vdev. Also add vdev id in all RSO commands logs
Change-Id: Iefa1e8ba177a64e141726ebaef15b250446a0af2
CRs-Fixed: 2789615
qdf_mem_malloc() function already takes care of logging the
caller function name and line number in case of any allocation error.
Hence there is no need to add the error log again.
Getting rid of these unnecessary logs reduces driver memory footprint.
Change-Id: If0b9425f82f9ed793c7639c0ed09eb1f868b6d5c
CRs-Fixed: 2781932
In the process of rso update config, need to send roam
scan_mode/deauth/idle/trigger commands when rso enabled.
Another fix is to call csr_cm_roam_scan_offload_fill_rso_configs()
with ROAM_SCAN_OFFLOAD_STOP in wlan_cm_roam_fill_stop_req().
Change-Id: Ibcc2ab5d7da1bf838b386e0e1e486cd43072225a
CRs-Fixed: 2779549
As part of WOW feature in WCN6750, send HOST wake up
to FW over QMI instead of WMI. To send HOST wake, add
PLD layer and call platform driver API to send QMI
EXIT_POWER_SAVE to FW.
When FW receive EXIT_POWER_SAVE QMI, it will implicitly
consider that it also received HOST_WAKEUP_FROM_SLEEP
and send ACK for it through CE2.
Change-Id: Ia0a3f4c15662f9ee58649f5c6de965f65aeafe32
CRs-Fixed: 2779370
Spectral parameter state information is accessed in both
process context and tasklet context. Currently
qdf_spin_lock/qdf_spin_unlock is used to protect these data structures.
This can lead to deadlock in the scenario where the process holding the
lock gets preempted by the tasklet. To avoid this use
qdf_spin_lock_bh/qdf_spin_unlock_bh.
CRs-Fixed: 2776902
Change-Id: I6d188e55d5066241b5f38a655f4a587c9edb0b8b
wmi_unified_register_event has a return type of QDF_STATUS.
Handle the same return type in the following callers:
1. target_if_dfs_reg_ocac_event
2. target_if_dfs_reg_offload_events
3. target_if_reg_phyerr_events_dfs2
Change-Id: I622f6f6c4ff3b428a6407b6526e823083cc1fd8a
CRs-Fixed: 2767507
Firmware advertizes its support to place FST in CMEM,
export this capability to DP.
Change-Id: I265246bcfd38a36e34c4ede66e117a92bb185032
CRs-Fixed: 2772238
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: I29fd5e645c7b43c74e28494c83a6f7d460165e2e
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: If77efc6a5b451bf2cf4acb59d5a2126ce486f02f
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: Ia6d1781f2bf1eea85d4af357e37a00b1f78e264e
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: I18c687ad0564ec70e28cf1f33f26501dda6ee5c5
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: I1dc098793e1df658666343d4293fe3f1c02daf34
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: Icfa7946a447f3cfe8c6ce933a618e8dbb67bd6a0
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: I87b1e6ee5e06e4e6af81395d977595335fe0bc5c
Host sets WMI_REQUEST_PMF_BCN_PROTECT_STAT bit in stats_id param of
WMI_REQUEST_STATS_CMDID command. Firmware supporting pmf beacon
protection stats responds host with stats in wmi_update_stats_id
event. Host extracts PMF beacon protection stats from wmi_update_stats_id
event. Host adds PMF beacon protection stats in the response of vendor
command QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO for STA mode.
Change-Id: Ib3cb06e03dbccdb9fa1782d414ed734bd97aa309
CRs-Fixed: 2705236
Add debug logs on the sending WMI_ROAM_SCAN_RSSI_THRESHOLD
/WMI_ROAM_FILTER_CMDID/WMI_ROAM_BTM_CONFIG_CMDID
/WMI_11K_OFFLOAD_REPORT_CMDID commands path.
If mawc roaming is not supported by firmware, don't send
WMI_ROAM_CONFIGURE_MAWC_CMDID command.
Add rssi reject AP list to the roam params process in function
csr_cm_roam_scan_filter().
Change-Id: I89e6dcac801e552877f7e918d1179dfa3466857a
CRs-Fixed: 2775101
3 ini:
roam_data_rssi_threshold_triggers
roam_data_rssi_threshold
rx_data_inactivity_time
If there's rx activity during latest rx_data_inactivity_time
and avg of data_rssi is better than roam_data_rssi_threshold, then
suppress roaming triggered by roam_data_rssi_threshold_triggers: low
RSSI or bg scan.
Change-Id: I5b41c4119e61392b50e52ab8ccb8650e5758f3b3
CRs-Fixed: 2768053
The logging macros implicitly takes care of embedding function name
in the log, hence there is no need to include __func__ again.
Getting rid of redundant __func__ reduces driver memory footprint.
Change-Id: Idf4685539991f65205f19b27551cef699230c82e
CRs-Fixed: 2768575
When user programs a non-zero scan count(say N), after receiving N
samples Spectral scan is supposed to be stopped. This change keeps track
of number of Spectral reports received from target and stops the
Spectral scan when programmed number of samples arrives at host.
CRS-Fixed: 2764935
Change-Id: Ibea0eeece4577fd6e0da302716869b05c900f917
The 2nd argument passed to the function is_primaryseg_expected
is used to index the array spectral->rparams.fragmentation_160 which
is of size 2.If the value of the argument is greater than or equal
to 2, the indexing will lead to array-out-of-bounds access.
The fix is adding the relevant validation check.
Change-Id: Iccf98b06c0546ad11ec67e93e14183214100107f
Add changes to send roam scan mode over RSO start/stop/update_cfg
from connection manager. Update the roaming params and roam scan
params to new structure.
Refine send_roam_scan_offload_mode_cmd_tlv().
Change-Id: I6adce2e8a24ece93a079032d0e66760393fcdccd
CRs-Fixed: 2766023
Add RSO logic to send roam trigger from target if along with
some optimization to move old logic in ROAM_OFFLOAD_V1.
Change-Id: I38e7fb4f8873328097df7e3a25d6c709f8d69b33
CRs-Fixed: 2765155
This change allow Tx VDEV of MBSS mode to configured
dynamically by reset the VDEVs.
This change includes FW service bit parsing, checking
VDEV state of all VDEVs, sending MBSS information in
VDEV start command
Change-Id: I46b13629bd1c07be86b408d72c2967642ce8542e
CRs-Fixed: 2759229
Release delete wakelock in delete response handler.
Release stop wakelock after sending the down command to
firmware so that it completes the disconnect sequence.
Change-Id: I0f47be04652178494d9cf0475af74ea573978005
CRs-Fixed: 2760116
Add support to send WMI_RSSI_CHANGE_THRESHOLD command to firmware
in connection manager.
Change-Id: I97d4b8f8fc0e938ede0e61d44eb8ffbcbb0fb4ff
CRs-Fixed: 2761043
To get the channel state for 5g bonded channel using the freq
use wlan_reg_get_5g_bonded_channel_state_for_freq.
Change-Id: I0b42e9c547ba70259e88137a5a26c238cd66da8d
CRs-Fixed: 2756463
When the option -Werror=tautological-compare is enabled, the compiler
reports error because bitwise comparison always evaluates to false.
Change-Id: I7532dc9bccb69e02be5f04897a6ecaff44e84a0d
CRs-Fixed: 2734883
Retrieve the max users per-PPDU supported in Uplink
and Downlink direction, from the fixed params of WMI
service ready ext2 event.
CRs-Fixed: 2747218
Change-Id: Ib9f9bd4313dd1955c607d4fe77b02e34761d1c20
The 'timestamp' field in CFR meta data corresponds to TSF
at the reception of PPDU in micro second unit. To capture
timestamp for one shot, periodic and repetitive channel
capture, this field is being used.
case 1:
For one shot and periodic capture, the clock used for
timestamp is private to the target and not visible to host.
So it is being passed by FW to host and the placeholder
being exchanged between Host and target is of 32 bit.
case 2:
In case of repetitive channel capture, the
timestamp is being populated from the received PPDU,
which is 64bit.
To accommodate the timestamp, in both above cases, change
the data type to u_int64_t from u_int32_t
Change-Id: Ifa612bd97dc4f597368daefcd4224b84f2484c03
CRs-Fixed: 2751408
Enable CFR support for IPQ5018.
Calculate stream FS buffer length based on CFR payload,
CFR uCode header and CSI metadata.
Change-Id: Idd903ead75d635ce87ffc0df80e5c32fb62d15aa
CRs-Fixed: 2751408
Repetitive channel capture configurations usually support
16 groups to be confugured. To check if a particular group
is enabled by user, qdf_test_bit is being used here.
qdf_test_bit usually operates with uint32_t and it takes
the argument as unsigned long type. Since,
modified_in_curr_session is declared as uint16_t, and then
typecasted into unsigned long.
Change the data type of modified_in_curr_session
from uint16_t to 'unsigned long' to avoid compiler
issues.
Change-Id: Iec778dc36d5671f2cfb643c9ced1bd2a6104de2b
CRs-Fixed: 2753267
Currently wifi positioning api to update channel bandwidth
info is invoking regulatory component api to set the channel
params with BW as CH_WIDTH_MAX, because of which regulatory
component is returning the maximum BW supported for the current
regdomain which is 160MHz. If target does not support 160MHz in
that case it may lead to undefined behavior.
To address this issue, pass max supported BW by target as
argument to regulatory component so that regulatory component
does not return the BW greater then the target supported BW.
CRs-Fixed: 2730665
Change-Id: I6051336ab2f3ea902a70ed80290e5a5f060de5b9
Host updates band to mac params and sends to FW in INIT command, FW uses
it to configure MACs. If host configures DBS in INIT command param but
FW doesn't advertise wmi_service_dual_band_simultaneous_support service
then host does not configure band to mac params in INIT command and let
the FW initialize MACs with default value.
As FW supports DBS and at the same time doesn't advertise
wmi_service_dual_band_simultaneous_support, host configures band to mac
params for only one MAC i.e. MAC0. FW either expects both the MACs
configuration from host or both not configured. If host configures only
one MAC, second MAC i.e. MAC1 configure remains empty. FW crashes as it
starts operation on MAC1. Hence host doesn't configure band to mac params
in INIT command.
Change-Id: I00104d7e6b911e0f792597346629b3c77c102c70
CRs-Fixed: 2752248
Add new code to implement below functions for connection manager
roam part:
And below two RSO command related process:
ROAM_SCAN_OFFLOAD_STOP
ROAM_SCAN_OFFLOAD_UPDATE_CFG
Change-Id: I378b969ddae77fff49ad1d4d8ce21764b292e5ac
CRs-Fixed: 2753011
Update the signal strength calculation logic in CFR to consider
negative SNR i.e., a signal below the noise floor.
CRs-Fixed: 2753751
Change-Id: I2e2b95cc2ac2cf50ad5b7e38977ab971ddeb1ecf
WMI handler is registered for twt_session_stats event.
Upon wmi event twt session parameters are extracted and
cached in peer mc_cp_stats. UMAC APIs are provided to
retrieve TWT session parameters from north bound
interface(hdd) using twt peer's mac_addr/session dialog_id
CRs-Fixed: 2730732
Change-Id: I8ce38ac6be97e844e26e03751c6d6cca981b82b4
Add freeze_tlv_version in cfir_enh_dma_hdr where,
version 1: Cypress/HastingsPrime which supports single user
channel capture
version 2: Maple/Spruce/Moselle which supports MU channel
capture for up to 4 users
version 3: Pine which supports MU channel capture for up to
37 users
CRs-Fixed: 2741027
Change-Id: Iadd6dc2ff82030f502776ce35988b4472450337e
For SAP on DFS channel, the PCIe link down should be prevented
so that HalPhy can access DDR memory to report Radar found event.
Change-Id: I5eb1076196c509f0279781dbe3269d62132aeabc
CRs-Fixed: 2712800
A new BDF option is added for scan radio boards to disable/enable DFS
detection. This flag is advertised to host via scan radio capabilities
TLV in ext2 service ready event. If customer sets the BDF so that DFS
need to be disabled, host skips the CAC timer and ignores the Radar
detection event. This change adds the following APIs.
1) Check given radio is a scan radio
2) DFS needs to be enabled/disabled for scan radio
CRs-Fixed: 2746779
Change-Id: Iabd34261aaa1067c7bbb76677aebcc8a3f89de43
FW advertises scan radio capabilities as part of service ready
ext2 event. This is an optional TLV, presence of which indicates scan
radio support for the that pdev.
CRS-Fixed: 2746769
Change-Id: I5a0231c54375e9f00c85f0ad92839e2fa6c79f39
With the newly introduced BLM enhancement, APs may get enlisted
and sent to FW for (re)assoc restraint. However, the FW side
AP restraint is only required when LFR3 is enabled.
With LFR2, no FW side AP (re)assoc restraint is required and all
actions will be done within driver code.
Use LFR3 specific conditional macro to enclose all the code
needed for sending reject AP list to FW.
Change-Id: I9a8bc0e25bc4b319bf1841324ef1b711f0659093
CRs-Fixed: 2751791
Add service ready parameter to update the capability for Preamble Puncturing
Tx support from target. Add WMI support for configuration of Punctured
band setting from Host.
Change-Id: If5714c162356c35c7c385c4596043c0bc671be9a
Change the receive and transmit Iv in wlan_crypto_set_wapi_key
such as:
tx_iv[16] = {0x5c, 0x36, 0x5c, 0x36, 0x5c,
0x36, 0x5c, 0x36, 0x5c, 0x36,
0x5c, 0x36, 0x5c, 0x36, 0x5c,
0x36};
rx_iv[16] = {0x5c, 0x36, 0x5c, 0x36, 0x5c,
0x36, 0x5c, 0x36, 0x5c, 0x36,
0x5c, 0x36, 0x5c, 0x36, 0x5c,
0x37};
This is done as wpi_key_tsc_counter sequence was been sent
in reverse order. 0x365C365C365C365C365C365C365C365C was
sent although 0x5C365C365C365C365C365C365C365C36 was expected.
This is because new chipset firware expects the format to be
in big endian. Also, taken care for the backward compatibility
required for the old chipset firware with the feature flag.
Change-Id: I8c795df5a9143e5089e93aaebe7787e51b570c74
CRs-Fixed: 2743162
In direct buf rx, if physical address is not intact or
is corrupt, the dbr lookup for vaddr will fail and result
in vaddr being NULL. There is no validation for this vaddr
in the caller and hence results in NULL access in the
callstack.
Add debug log and return error status when dbr
vaddr lookup fails, which indicates that there is
corruption in paddr received and avoid NULL access.
Change-Id: I76ee300ce3e686765dd5c4ee73fa71d1735c163a
CRs-Fixed: 2748529
Add connection manager changes to send roam scan offload init
deinit. Add new enum roam_offload_init_flags to fill the roam
init/deinit flags, 4-way handshake offload, bmiss skip full scan
flags at connection manager instead of getting the ini and filling
at target if.
Change-Id: I558e868efd341b508d3df76c8d6ab90eac512432
CRs-Fixed: 2745585
Support a new capture_interval_mode: capture_count, where after
capture_count+1 number of frames, MAC stops channel capture and
waits for capture_interval duration before enabling again.
Add nob(capture_intervalmode_sel) to switch to capture_count or
capture_duration mode in wlanconfig application, where
capture_intervalmode_sel=0 indicates the old capture_durarion
mode where MAC stops channel capture after capture_duration
instead of capture_count. capture_intervalmode_sel=1 indicates
the capture_count mode.
Support MO marking: Current ENH CFR uses the existing MD/MO,
type/subtype filters to filterin the packets with programmed
type/subtype as either MD/MO. But for m_TARA it is also required
to consider the bw/nss/ta/ra setting. Therefore, it is possible
that not all the filtered-in PPDUs have channel capture and lead
to processing of packets which does not have captured data.
To overcome this issue, from QCN9000 onwards, MAC has MO marking
feature added for M_TARA filter mode, where MAC will consider
all TARA group configuration as filterin criteria & provides
an option to HOST to choose either filterin mode as FP or MO.
en_ta_ra_filter_in_as_fp is added to support MO marking.
Based on the discussion between HOST, FW & MAC teams, 0 is the
recommended & default setting for en_ta_ra_filter_in_as_fp.
Add nob to configure en_ta_ra_filter_in_as_fp but do not expose
to user.
Change-Id: I790d7ce500a7d779ea571635690f73dbc582cf33
To handle no-inter-band MCC scenarios for dual MAC non-DBS solutions,
add changes to detect capability at run-time based on service bits.
If the service is set then code for only intra-band MCC will be
exercised.
Change-Id: I402311fcecfd03bba67fedfb2b52f779f60b81ce
CRS-Fixed: 2730374
It starts spectral scan without vdev object, and uses the first vdev
as current vdev. which cause vdev mismatch in some platforms. So pass
vdev object or id when finding current vdev.
Change-Id: Iab55afbe2c98906021a008918f186d3d2dce5871
CRS-Fixed: 2716460
Add new channel bonding pairs as well as frequency
pairs for 40, 80 and 160 MHz with the support of
three new 5.9 GHz channels 169, 173 and 177.
Add new API reg_modify_chan_list_for_5dot9_ghz_channels
to enable/disable these new channels based on
INI value and service bit.
Change-Id: I8598e705ba4047e96e7167661ba70d4236cde251
CRs-Fixed: 2696211
Add macro ROAM_OFFLOAD_V1 for new code and implement below functions
for connection manager roam part:
csr_handle_roam_state_change() roam offload state related handler.
Filling WMI_ROAM_SCAN_RSSI_THRESHOLD cmd parameters related process.
Change-Id: I0351155ca5a3d68ade6568c7527c5708582ccf1a
CRs-Fixed: 2730826
For adrastea targets, enhanced CFR is not supported. When only
CONFIG_WLAN_CFR_ENABLE is set, some compilation errors are
observed as CONFIG_WLAN_ENH_CFR_ENABLE is not set true.
Fix these compilation errors when only CONFIG_WLAN_CFR_ENABLE
is set for targets which do not support enhanced CFR.
Change-Id: I96a769d8f10144033e48e123bb68d48a54cdf8ab
CRs-Fixed: 2706904
Add wrapper functions to get the host pdev id from target pdev id and
vice versa.
Change-Id: Ib10f6f5625b4a9e1f44a13e9185de75f6df88b3c
CRs-Fixed: 2711423
a. Enable DDMA support and FFT bin length adjustment SWARs
b. Similar to QCN9000,
Skip 16 bytes of unused padding added after Spectral summary report
FFT report header length is 24
Change-Id: I870f198511771dccbb0300ff62fc15ab0d64ee7f
NAN protocol runs in firmware and controlled by framework.
Framework configures multiple NAN discovery params while enabling
NAN. Framework configurations would be based on the framework
constraints or realtime scenarios like resource(memory/power/..)
consumption. But some of these params might need to be controlled
explicitly based on the usage.
NAN DW is one such parameter, which is configured as 4 seconds
when the device is in sync role and the screen is off. But
for some usecases, this param might have to be 512ms always
irrespective of screen off/on for some targets. Add an ini param
"nan_feature_config" to set a bit to indicate firmware whether to
honor framework configured DW value or the firmware default value.
Send the vdev param on NAN supported vdev by setting the "bit 0"
to indicate firmware to allow framework configured DW value.
If this bit is not set, firmware shall consider its default value.
Change-Id: I0476bca2bbe676beccfff207f5b4ea31e89031e2
CRs-Fixed: 2721970
