Remove warnings in ep93xx-i2s.c
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Extend range of supported sample rates for CS4271 CODEC.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a codec driver for the dfbmcs320 bluetooth module, which is used
on the neo1973 boards.
The patch also modifies the neo1937_wm8753 sound board driver to use the new
driver instead of registering the bluetooth DAI manually.
Previously there was a name mismatch between the bluetooth DAI and the bluetooth
DAI link and the sound card was not instantiated, with this patch the issue is
no longer present and sound support works again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The neo1973(GTA01) and neo1973_gta02(GTA02) have a very similar audio hardware
setup. They both use the same codec with the same routing to the gsm modem and
bluetooth chip. But they do use different AMPs though and there are some minor
differences in the speaker setup.
As a result most of the code of those two drivers is identical.
So from a maintenance point of view it makes sense to merge them into a single
driver. It also reduces the size of kernel images supporting both the GTA01 and
GTA02.
As a side-effect of this merge the GTA01 for example gains support for routing
audio to and from the bluetooth DAI.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using gpio_request_array instead of requesting and setting up each gpio by hand
makes the code more readable and more compact.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch drops the lm4853_{set,get}_state functions and the "Amp State Switch"
control.
Those were noops which existed to maintain alsa state file compatibility. Since
the control names have changed due to internal changes in the ASoC core and
state file compatibility was broken anyway it makes sense to drop them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch moves the code for the lm4857 AMP from the neo1973_wm8753 sound
board driver to its own module.
The lm4857 is a generic AMP IC and not specific to the neo1973.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has been proven to be inflexible to do scenario management in kernel space.
Since actual neo1973 board support has not been merged in mainline and this
patch has been in the neo1973 tree for some time now it should be safe to remove
this functionality without breaking existing userspace.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Visstrim_M10 boards have an external tlcv320aic3205 codec
attached to SSI1. This driver glues together both interfaces.
External amplifier is not supported in this first version.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for tlv320aic3205 and tlv320aic3254 codecs.
It doesn't include miniDSP support for aic3254.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is run after the DAPM widgets and routes are added, allowing setup
of things like jacks using the routes. The main card probe() is run before
anything else so can't be used for this purpose.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
These will be added after all devices are registered and allow most DAI
init functions in machine drivers to be replaced by simple data.
Regular controls are not supported as the registration function still
works in terms of CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This means that rather than adding the board specific DAPM widgets to a
random CODEC DAPM context they can be added to the card itself which is
a bit cleaner. Previously there only was one DAPM context and it was
tied to the single supported CODEC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
A CODEC pointer is optional (and is checked for in most contexts within
DAPM) - add checks to the few places where it was missed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than indirecting through the CODEC we can look the card up directly
from the card pointer in the DAPM context.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9081 IRQ output can be either active high or active low and can
support either CMOS or open drain modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
When choosing IMX_DMA flag, burtsizes are set to its default
value (0) which leads to driver malfunction. Change them to 4.
DSP_B interface needs additional flag to match DSP_B formats
as described in several codecs as wm8741 and aic3205.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the ADCs are provided with a clock as the previous patch
"ASoC: WM8994: Improve playback robustness" did not handle this case
properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Since we began using the late clock disable functionality, ensure that
we don't disable the clock if any of the ADC or DAC paths are still
enabled. This happens when we have simultaneous playback and recording.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
It went AWOL in the multi-component conversion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Get rid of users of of_platform_driver in drivers/sound. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
tegra_dma_allocate_channel() returns NULL on errors, not an error pointer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove unnecessary headers:
- mach/hardware.h in sgtl5000.c
- linux/i2c.h in sgtl5000.h
Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's a general move to use dev_pm_ops rather than bus specific functions
in order to facilitate work on the PM core. Do this conversion to WM2000.
The driver ought to be updated to work better in a multi-component model
but the mechanical conversion ensures that we avoid blocking PM core work
until that happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
commit f0fba2ad1b6b53d5360125c41953b7afcd6deff0 included a mistake
on the name of the platform in the snd_soc_dai_link structure.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The utilities will be required by every machine driver. Including the
utility object directly into every machine driver causes a build failure
if the modules are actually built into the kernel, since each will define
the symbols exported by the utility file. Solve this by moving the
utility object into a separate module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes the name of the control switch of a dapm route contains
spaces which makes it impossible to distinguish it from the source widget.
Add quotes around the names of the widgets to makes these parsable.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct names for pxa AC97 DAI are pxa2xx-ac97 and pxa2xx-ac97-aux. Fix
that for all PXA platforms.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
