Leaving for_each_child_of_node loop we should release child device node,
if it is not stored for future use.
Found by Linux Driver Verification project (linuxtesting.org).
JC: I'm not sending this as a quick fix as it's been wrong for years,
but good to pick up for stable after the merge window.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 6df2e98c3ea56 ("iio: adc: Add imx25-gcq ADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This changes how the SPI message for the triggered buffer is setup in
the TI ADS7950 A/DC driver. By using the SPI_CS_WORD flag, we can read
multiple samples in a single SPI transfer. If the SPI controller
supports DMA transfers, we can see a significant reduction in CPU usage.
For example, on an ARM9 system running at 456MHz reading just 4 channels
at 100Hz: before this change, top shows the CPU usage of the IRQ thread
of this driver to be ~7.7%. After this change, the CPU usage drops to
~3.8%.
The use of big-endian for the raw data was cargo culted from another
driver when this driver was originally written. It used an SPI word size
of 8 bits and big-endian byte ordering to effectively emulate 16 bit
words.
Now, in order to inject a CS toggle between each word, we need to use
the correct word size, otherwise we would get a CS toggle half way
through each word 16-bit. The SPI subsystem uses CPU byte ordering for
multi-byte words. So, the data we get back from the SPI is going to be
CPU endian now no matter what. Converting that to big endian will just
add overhead on little endian systems so we opt to change the raw data
format from big endian to CPU endian.
There is a small risk that this could break some lazy userspace programs
that use the raw data without checking the data format. We can address
this if/when it actually comes up.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a merge commit in here to pull in regmap support for repeatedly
reading the same register (to read out FIFOs). Used by the adxl372 driver.
This will find uses elsewhere once we tidy up various drivers that are
effectively doing this and relying on not enabling regcache.
New device support
* Analog devices ADXL372 accelerometer
- new driver for this accelerometer including fifo and and interrupt support.
Follow up patches enforce trigger validation, add sampling frequency
control and filter bandwidth control. A later series added i2c support
to the existing SPI support.
* ST lsm6dsx
- rework and add support fo the LSM6DSO 6 axis mems sensor.
* Linear LTC 1660 DAC
- new driver supporting the LTC 1660 and LTC 1665 SPI DACs.
* Microchip mcp3911 ADC.
- new driver for this integrated analog front end and ADC.
* Qualcomm SPMI PMIC5 adc driver
- using the spmi framework, new driver and bindings for this ADC.
Follow up patch adds some missing channels.
Features
* ad5758
- support hard reset using a gpio (if provided).
* mpu6050
- Regulator support
* qcom-spmi-adc5
- Sanity check the channel numbers provided by DT to make sure the
driver actually knows about them.
* sc27xx
- give raw data for channel 20 as it's used on all known boards for
the headset which needs a custom converstion function. If it turns
out someone builds a board where this isn't true we will deal with it
when it happens.
- add ADC scale calibration.
* tsl2772
- support device tree binding to set the proximity led settings.
- regulator supprot.
- binding for apds9930 - trivial addition as register compatible with tsl2772.
Cleanups / Minor fixes
* adxl345
- supress a static checker warning but explicitly checking if the id
object is null.
* bh1750
- avoid CONFIG_PM_SLEEP checks.
- SPDX.
* bme680
- spelling mistake
- use clamp rather than open coding.
- white space and other similar fixes.
- rename MSK to MASK for clarifty and use GENMASK to specify them.
- use the FIELD_GET macro rather than a very odd accessor of dividing by
16 to get the shift.
- rework to share handing for oversampling of the various channels in a
unified way.
- check explicitly for val2 in write_raw function to ensure it is 0.
- drop some field defines that don't add anything.
* dpot-adc
- SPDX
* envelope detector
- SPDX
* isl29501
- fix an ancient compiler warning mostly because it results in much
nicer code.
* max30102
- mark switch fall throughs.
* max44000
- drop an unused variable.
* max512
- avoid CONFIG_PM_SLEEP checks.
* max5481
- use of_device_get_match_data rather than open coding it.
* max5821
- avoid CONFIG_PM_SLEEP checks.
* max9611
- explicity cast an enum to an integer to make it totally clear that
this is intended.
* mcp4018
- fix an inconsistent MODULE_LICENSE.
- use of_device_get_match_data rather than open coding it.
* mcp4531
- use of_device_get_match_data rather than open coding it.
- SPDX
* mcp4725
- avoid CONFIG_PM_SLEEP checks.
* mcp4922
- Fix error handling and prevent writing a negative to when setting the
output voltage.
* ms5611
- drop deprecated compatible strings without manufacturer from being
explicitly listed. They are handled anyway.
- SPDX
* multiplexer
- SPDX
* qcom-vadc
- fix inconsistent documentation for reg.
* ti-dac5571
- provide and of_match_table.
* treewide
- update Michael Hennerich's email address.
- Use %pOFn rather than device_node.name.
* documentation.
- tidy up a wrong kernel version for the introduction of the
position_relative ABI.
-----BEGIN PGP SIGNATURE-----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=+9gG
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st round of IIO new device support, features and cleanups in the 4.20 cycle.
There is a merge commit in here to pull in regmap support for repeatedly
reading the same register (to read out FIFOs). Used by the adxl372 driver.
This will find uses elsewhere once we tidy up various drivers that are
effectively doing this and relying on not enabling regcache.
New device support
* Analog devices ADXL372 accelerometer
- new driver for this accelerometer including fifo and and interrupt support.
Follow up patches enforce trigger validation, add sampling frequency
control and filter bandwidth control. A later series added i2c support
to the existing SPI support.
* ST lsm6dsx
- rework and add support fo the LSM6DSO 6 axis mems sensor.
* Linear LTC 1660 DAC
- new driver supporting the LTC 1660 and LTC 1665 SPI DACs.
* Microchip mcp3911 ADC.
- new driver for this integrated analog front end and ADC.
* Qualcomm SPMI PMIC5 adc driver
- using the spmi framework, new driver and bindings for this ADC.
Follow up patch adds some missing channels.
Features
* ad5758
- support hard reset using a gpio (if provided).
* mpu6050
- Regulator support
* qcom-spmi-adc5
- Sanity check the channel numbers provided by DT to make sure the
driver actually knows about them.
* sc27xx
- give raw data for channel 20 as it's used on all known boards for
the headset which needs a custom converstion function. If it turns
out someone builds a board where this isn't true we will deal with it
when it happens.
- add ADC scale calibration.
* tsl2772
- support device tree binding to set the proximity led settings.
- regulator supprot.
- binding for apds9930 - trivial addition as register compatible with tsl2772.
Cleanups / Minor fixes
* adxl345
- supress a static checker warning but explicitly checking if the id
object is null.
* bh1750
- avoid CONFIG_PM_SLEEP checks.
- SPDX.
* bme680
- spelling mistake
- use clamp rather than open coding.
- white space and other similar fixes.
- rename MSK to MASK for clarifty and use GENMASK to specify them.
- use the FIELD_GET macro rather than a very odd accessor of dividing by
16 to get the shift.
- rework to share handing for oversampling of the various channels in a
unified way.
- check explicitly for val2 in write_raw function to ensure it is 0.
- drop some field defines that don't add anything.
* dpot-adc
- SPDX
* envelope detector
- SPDX
* isl29501
- fix an ancient compiler warning mostly because it results in much
nicer code.
* max30102
- mark switch fall throughs.
* max44000
- drop an unused variable.
* max512
- avoid CONFIG_PM_SLEEP checks.
* max5481
- use of_device_get_match_data rather than open coding it.
* max5821
- avoid CONFIG_PM_SLEEP checks.
* max9611
- explicity cast an enum to an integer to make it totally clear that
this is intended.
* mcp4018
- fix an inconsistent MODULE_LICENSE.
- use of_device_get_match_data rather than open coding it.
* mcp4531
- use of_device_get_match_data rather than open coding it.
- SPDX
* mcp4725
- avoid CONFIG_PM_SLEEP checks.
* mcp4922
- Fix error handling and prevent writing a negative to when setting the
output voltage.
* ms5611
- drop deprecated compatible strings without manufacturer from being
explicitly listed. They are handled anyway.
- SPDX
* multiplexer
- SPDX
* qcom-vadc
- fix inconsistent documentation for reg.
* ti-dac5571
- provide and of_match_table.
* treewide
- update Michael Hennerich's email address.
- Use %pOFn rather than device_node.name.
* documentation.
- tidy up a wrong kernel version for the introduction of the
position_relative ABI.
Relying on CONFIG_PM_SLEEP to set PM ops is not necessary
since core will handle everything internally. One have to only make sure
that functions that can go unused are marked with __maybe_unused.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adxl372 is designed to communicate in either SPI or I2C protocol. It
autodetects the format being used, requiring no configuration control to
select the format.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch restructures the existing adxl372 driver by adding a module for
SPI and a header file, while the baseline module deals with the chip-logic.
This is a necessary step, as this driver should support in the future
a similar device which differs only in the type of interface used (I2C
instead of SPI).
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop boilerplate license text and use SPDX identifier instead.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop boilerplate license text and use SPDX identifier instead.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSO 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dso.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add reg addr and max_word_len parameters to st_lsm6dsx_read_block
since LSM6DSO will use a different register address to read samples
from the FIFO and a different sample len
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove static qualifier from st_lsm6dsx_check_odr() definition in order to
use it for the support of new devices
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove static qualifier from st_lsm6dsx_read_fifo definition and
introduce read_fifo function pointer in fifo_ops data structure
in order to run the proper read_fifo routine since other compliant
devices will use a different FIFO queueing scheme.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad5758 has a hardware reset active low input pin. This patch adds a
devicetree entry for a reset GPIO and a new ad5758_reset() function.
During
initialization, it is checked if the reset property is specified and the
the GPIO is being asserted, therefore the device will become active.
When the reset function is called, if the gpio_reset var is set, then
the
GPIO will be toggled, otherwise a software reset is performed.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver only defines a subset of all possible ADC channels. Channel
numbers read from the device tree are accepted as long as they don't
exceed a max value, even when no channel definition exists. Add a
check to abort initialization in this case.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With gcc 4.1.2:
drivers/iio/proximity/isl29501.c: In function ‘isl29501_register_write’:
drivers/iio/proximity/isl29501.c:235: warning: ‘msb’ may be used uninitialized in this function
While this is a false positive, it can easily be avoided by removing the
"msb" intermediate variable.
Remove the "lsb" intermediate variable for consistency.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support to read calibration values from the eFuse
controller to calibrate the ADC channel scales, which can make ADC
sample data more accurate.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The headset device will use channel 20 of ADC controller to detect events,
but it needs the raw ADC data to do conversion according to its own formula.
Thus we should configure the channel mask separately and configure channel
20 as IIO_CHAN_INFO_RAW, as well as adding raw data read support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the created list of of_device_id's as a match table.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not try to write negative values and make sure that the write goes well.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
LTC1665/LTC1660 is a 8/10-bit Digital-to-Analog Converter
(DAC) with eight individual channels.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the option for the user to select the filter bandwidth. The
user can also read the available bandwidths which are always adjusted to be
at most half of the sampling frequency. Furthermore, the currently selected
bandwidth can be read via the read_raw function, while the write_raw sets a
new bandwidth value.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the option for the user to select the sampling frequency.
Also, the user can read the available frequencies and read the currently
set frequency via the read_raw function. The frequency can be set via the
write_raw function.
When the frequency is set, the bandwidth is also checked and ensured
that it is constrained to at most half of the sampling frequency. Also, the
activity and inactivity timers have to be updated because they depend on
the selected ODR.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch provides a validate_device callback for the trigger which makes
sure that other devices are rejected.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove BME680_RUN_GAS_EN_BIT and BME680_NB_CONV_0_VAL field value
definitions because the fields are simply boolean and integer
respectively.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Tested-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Almost all files in the kernel are either plain text or UTF-8 encoded. A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.
This converts them all to UTF-8 for consistency.
Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
Drop the boilerplate license text and use the correct MODULE_LICENSE.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop call to of_match_device, which is subsumed by the subsequent
call to of_device_get_match_data. The code becomes simpler, and a
temporary variable can be dropped.
The semantic match that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression match;
identifier i;
expression x, dev, e, e1;
@@
- match@i = of_match_device(x, dev);
- if (match) e = of_device_get_match_data(dev);
- else e = e1;
+ e = of_device_get_match_data(dev);
+ if (!e) e = e1;
@@
identifier r.i;
@@
- const struct of_device_id *i;
... when != i
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
val2 is responsible for the floating part of the number to be
written to the device. We don't need the floating part
while writing the oversampling ratio for BME680 since the
available oversampling ratios are pure natural numbers.
So, add a sanity check to make sure val2 is 0.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MCP3911 is a dual channel Analog Front End (AFE) containing two
synchronous sampling delta-sigma Analog-to-Digital Converters (ADC).
Co-developed-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes ef89f4b96a2 ("iio: adxl345: Add support for the ADXL375").
This was found via static checker.
After looking into the code a bit, it's unlikely that there will be a NULL
dereference if the `id` object in that specific code path.
However, it's safe to add a NULL (paranoid) check just to make sure and
remove any uncertainties.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Variable max44000_alstim_shift is defined but is never used hence it is
redundant and can be removed. This variable has been like this since
the driver was added back in 2016.
Cleans up clang warning:
warning: 'max44000_alstim_shift' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for the adxl372 FIFO. In order to accomplish this,
triggered buffers were used.
The number of FIFO samples which trigger the watermark interrupt can be
configured by using the buffer watermark. The FIFO format is determined by
configuring the scan elements for each axis. The FIFO data is pushed to the
IIO device's buffer.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds basic support for Analog Devices ADXL372 SPI-Bus
Three-Axis Digital Accelerometer.
The device is probed and configured the with some initial default
values. With this basic driver, it is possible to read raw acceleration
data.
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL372.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ADC5_AMUX_THM2_100K_PU and ADC5_AMUX_THM4_100K_PU to the list of
rev2 ADC channels.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After finding a reasonable gain, the function converts the configured
gain to a gain configuration option selector enum max9611_csa_gain.
Make the conversion clearly visible by using an explicit cast. This
also avoids a warning seen with clang:
drivers/iio/adc/max9611.c:292:16: warning: implicit conversion from
enumeration type 'enum max9611_conf_ids' to different enumeration
type 'enum max9611_csa_gain' [-Wenum-conversion]
*csa_gain = gain_selectors[i];
~ ^~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is already handled by SIMPLE_DEV_PM_OPS().
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is already handled by SIMPLE_DEV_PM_OPS().
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is already handled by SIMPLE_DEV_PM_OPS().
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I placed the "fall through"
annotation at the bottom of the case, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 1458342 ("Missing break in switch")
Addresses-Coverity-ID: 1458345 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Compatible strings tend to follow manufacturer,model format.
In case one wants to do a matching with manufacturer stripped
off he can still do so since SPI/I2C core will try id_table
based matching anyway.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Temperature, pressure and humidity all expose and oversampling setting
that works in the same way. Provide common handling for the
oversampling sysfs attributes.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Tested-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the FIELD_GET macro instead of explicit mask and shift.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Tested-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
