[ Upstream commit 9c9509717b53e701469493a8d87ed42c7d782502 ]
Starting with 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845
controller support"), the ads7845 was partially converted to full duplex
mode.
Since it is not touchscreen controller specific, it is better to extend
this conversion to cover entire driver. This will reduce CPU load and make
driver more readable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-2-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 13f82ca3878d ("Input: ads7846 - always set last command to PWRDOWN")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3689abfc4e369a643d758a02fb9ad0b2403d6d6d ]
Unless it is being done as part of servicing a soft reset interrupt,
configuring channels on-the-fly (as is the case when writing to the
ati_trigger attribute) may cause GPIO3 (which reflects the state of
touch for a selected channel) to be inadvertently asserted.
To solve this problem, follow the vendor's recommendation and write
all channel configuration as well as the REDO_ATI register field as
part of a single block write. This ensures the device has been told
to re-calibrate itself following an I2C stop condition, after which
sensing resumes and GPIO3 may be asserted.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs8GyV7g0nF5Yy@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e023cc4abde3c01b895660b0e5a8488deb36b8c1 ]
The time the device takes to deassert its RDY output following an
I2C stop condition scales with the core clock frequency.
To prevent level-triggered interrupts from being reasserted after
the interrupt handler returns, increase the time before returning
to account for the worst-case delay (~140 us) plus margin.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs484ypy4dab5G@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59bc9cb3b80abaa42643abede0d5db8477901d9c ]
Each call to device/fwnode_get_named_child_node() must be matched
with a call to fwnode_handle_put() once the corresponding node is
no longer in use. This ensures a reference count remains balanced
in the case of dynamic device tree support.
Currently, the driver does not call fwnode_handle_put() on nested
event nodes. This patch solves this problem by adding the missing
instances of fwnode_handle_put().
As part of this change, the logic which parses each channel's key
code is gently refactored in order to reduce the number of places
from which fwnode_handle_put() is called.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/Y7Rsx68k/gvDVXAt@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c445d2637c938a800fcc8b5f0b10e60c94460c7 ]
The Clevo PCX0DX/TUXEDO XP1511, need quirks for the keyboard to not be
occasionally unresponsive after resume.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20230110134524.553620-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6a87c36165e6791eeaed88025cde270536c3198 ]
A lot of modern Clevo barebones have touchpad and/or keyboard issues after
suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of them
have an external PS/2 port so this can safely be set for all of them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use. No negative effects could be
observed when setting all four.
The list is quite massive as neither the TUXEDO nor the Clevo dmi strings
have been very consistent historically. I tried to keep the list as short
as possible without risking on missing an affected device.
This is revision 3. The Clevo N150CU barebone is still removed as it might
have problems with the fix and needs further investigations. The
SchenkerTechnologiesGmbH System-/Board-Vendor string variations are
added. This is now based in the quirk table refactor. This now also
includes the additional noaux flag for the NS7xMU.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-5-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff946268a0813c35b790dfbe07c3bfaa7bfb869c ]
Merge i8042 quirk tables to reduce code duplication for devices that need
more than one quirk. Before every quirk had its own table with devices
needing that quirk. If a new quirk needed to be added a new table had to
be created. When a device needed multiple quirks, it appeared in multiple
tables. Now only one table called i8042_dmi_quirk_table exists. In it every
device has one entry and required quirks are coded in the .driver_data
field of the struct dmi_system_id used by this table. Multiple quirks for
one device can be applied by bitwise-or of the new SERIO_QUIRK_* defines.
Also align quirkable options with command line parameters and make vendor
wide quirks per device overwriteable on a per device basis. The first match
is honored while following matches are ignored. So when a vendor wide quirk
is defined in the table, a device can inserted before and therefore
ignoring the vendor wide define.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-3-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95a9916c909f0b1d95e24b4232b4bc38ff755415 ]
Move __intconst from before i8042_dmi_laptop_table[] to after it for
consistent code styling.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-2-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3c44e2b6cde674797b76e76d3a903a63ce8a18bb upstream.
This reverts commit ac5408991ea6b06e29129b4d4861097c4c3e0d59 because
it causes loss of keyboard on HP 15-da1xxx.
Fixes: ac5408991ea6 ("Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode")
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/824effa5-8b9a-c28a-82bb-9b0ab24623e1@kernel.org
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1206358
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a85fbd6498441694475716a4d5c65f9d3e073faf ]
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
Fixes: afe10358e4 ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e13757f52496444b994a7ac67b6e517a15d89bbc ]
Like on the Acer Switch 10 SW5-012, the Acer Switch V 10 SW5-017's _LID
method messes with home- and power-button GPIO IRQ settings, causing an
IRQ storm.
Add a quirk entry for the Acer Switch V 10 to the dmi_use_low_level_irq[]
DMI quirk list, to use low-level IRQs on this model, fixing the IRQ storm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e9ada1d0e72b4737df400fe1bba48dc42a68df7 ]
It seems that the Windows drivers for the ACPI0011 soc_button_array
device use low level triggered IRQs rather then using edge triggering.
Some ACPI tables depend on this, directly poking the GPIO controller's
registers to clear the trigger type when closing a laptop's/2-in-1's lid
and re-instating the trigger when opening the lid again.
Linux sets the edge/level on which to trigger to both low+high since
it is using edge type IRQs, the ACPI tables then ends up also setting
the bit for level IRQs and since both low and high level have been
selected by Linux we get an IRQ storm leading to soft lockups.
As a workaround for this the soc_button_array already contains
a DMI quirk table with device models known to have this issue.
Add a module parameter for this so that users can easily test if their
device is affected too and so that they can use the module parameter
as a workaround.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e37cc6240767f794678d11704935d49cc81d59 ]
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac5408991ea6b06e29129b4d4861097c4c3e0d59 ]
The device works fine in native RMI mode, there is no reason to use legacy
PS/2 mode with it.
Signed-off-by: Aman Dhoot <amandhoot12@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81cd7e8489278d28794e7b272950c3e00c344e44 ]
Avoid resetting the module-wide i8042_platform_device pointer in
i8042_probe() or i8042_remove(), so that the device can be properly
destroyed by i8042_exit() on module unload.
Fixes: 9222ba68c3f4 ("Input: i8042 - add deferred probe support")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Link: https://lore.kernel.org/r/20221109034148.23821-1-chenjun102@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b8ebf250997c5fb253582f42bfe98673801ebebd upstream.
syzbot is reporting uninitialized value at iforce_init_device() [1], for
commit 6ac0aec6b0 ("Input: iforce - allow callers supply data buffer
when fetching device IDs") is checking that valid length is shorter than
bytes to read. Since iforce_get_id_packet() stores valid length when
returning 0, the caller needs to check that valid length is longer than or
equals to bytes to read.
Reported-by: syzbot <syzbot+4dd880c1184280378821@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 6ac0aec6b0 ("Input: iforce - allow callers supply data buffer when fetching device IDs")
Link: https://lore.kernel.org/r/531fb432-7396-ad37-ecba-3e42e7f56d5c@I-love.SAKURA.ne.jp
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17b9841152e7f4621619902b347e2cc39c32996 upstream.
Suspending and resuming the system can sometimes cause the out
URB to get hung after a reset_resume. This causes LED setting
and force feedback to break on resume. To avoid this, just drop
the reset_resume callback so the USB core rebinds xpad to the
wireless pads on resume if a reset happened.
A nice side effect of this change is the LED ring on wireless
controllers is now set correctly on system resume.
Cc: stable@vger.kernel.org
Fixes: 4220f7db1e ("Input: xpad - workaround dead irq_out after suspend/ resume")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Link: https://lore.kernel.org/r/20220818154411.510308-3-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e62563db857f81d75c5726a35bc0180bed6d1540 upstream.
Both i.MX6 and i.MX8 reference manuals list 0xBF8 as SNVS_HPVIDR1
(chapters 57.9 and 6.4.5 respectively).
Without this, trying to read the revision number results in 0 on
all revisions, causing the i.MX6 quirk to apply on all platforms,
which in turn causes the driver to synthesise power button release
events instead of passing the real one as they happen even on
platforms like i.MX8 where that's not wanted.
Fixes: 1a26c92071 ("Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q")
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4599101.ElGaqSPkdT@pliszka
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 425fe4709c76e35f93f4c0e50240f0b61b2a2e54 ]
This controller is used by PinePhone and PinePhone Pro. Support for
the PinePhone Pro will be added in a later patch set.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Jarrah Gosbell <kernel@undef.tools>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220809091200.290492-1-kernel@undef.tools
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99077ad668ddd9b4823cc8ce3f3c7a3fc56f6fd9 ]
Add the module alias so the rk805-pwrkey driver will
autoload when built as a module.
Fixes: 5a35b85c2d ("Input: add power key driver for Rockchip RK805 PMIC")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220612225437.3628788-1-pbrobinson@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 98e01215708b6d416345465c09dce2bd4868c67a upstream.
syzbot is reporting hung task at __input_unregister_device() [1], for
iforce_close() waiting at wait_event_interruptible() with dev->mutex held
is blocking input_disconnect_device() from __input_unregister_device().
It seems that the cause is simply that commit c2b27ef672 ("Input:
iforce - wait for command completion when closing the device") forgot to
call wake_up() after clear_bit().
Fix this problem by introducing a helper that calls clear_bit() followed
by wake_up_all().
Reported-by: syzbot <syzbot+deb6abc36aad4008f407@syzkaller.appspotmail.com>
Fixes: c2b27ef672 ("Input: iforce - wait for command completion when closing the device")
Tested-by: syzbot <syzbot+deb6abc36aad4008f407@syzkaller.appspotmail.com>
Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Co-developed-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/887021c3-4f13-40ce-c8b9-aa6e09faa3a7@I-love.SAKURA.ne.jp
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e61b3125a4f036b3c6b87ffd656fc1ab00440ae9 upstream.
The function ioremap() in gscps2_probe() can fail, so
its return value should be checked.
Fixes: 4bdc0d676a ("remove ioremap_nocache and devm_ioremap_nocache")
Cc: <stable@vger.kernel.org> # v5.6+
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: Xie Shaowen <studentxswpy@163.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit feedaacdadfc332e1a6e436f3adfbc67e244db47 ]
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab2e51898cd4343bbdf8587af8ce8fbabddbcb5 ]
Commit 223f61b8c5 ("Input: soc_button_array - add Lenovo Yoga Tablet2
1051L to the dmi_use_low_level_irq list") added the 1051L to this list
already, but the same problem applies to the 1051F. As there are no
further 1051 variants (just the F/L), we can just DMI match 1051.
Tested on a Lenovo Yoga Tablet2 1051F: Without this patch the
home-button stops working after a wakeup from suspend.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220603120246.3065-1-mail@mariushoch.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c42e65664390be7c1ef3838cd84956d3a2739d60 upstream.
The bcm5974 driver does the allocation and dma mapping of the usb urb
data buffer, but driver does not set the URB_NO_TRANSFER_DMA_MAP flag
to let usb core know the buffer is already mapped.
usb core tries to map the already mapped buffer, causing a warning:
"xhci_hcd 0000:00:14.0: rejecting DMA map of vmalloc memory"
Fix this by setting the URB_NO_TRANSFER_DMA_MAP, letting usb core
know buffer is already mapped by bcm5974 driver
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215890
Link: https://lore.kernel.org/r/20220606113636.588955-1-mathias.nyman@linux.intel.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f76955ab1e43e5795a9631b22ca4f918a0ae986 ]
The commit 26623eea0da3 attempted to deal with potential leak of runtime
PM counter when opening the touchscreen device, however it ended up
erroneously dropping the counter in the case of successfully enabling the
device.
Let's address this by using pm_runtime_resume_and_get() and then executing
pm_runtime_put_sync() only when we fail to send "sense on" command to the
device.
Fixes: 26623eea0da3 ("Input: stmfts - fix reference leak in stmfts_input_open")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8994b30d71d64d5dcc9bc0edbfdf367171aa96f ]
of_find_node_by_path() calls of_find_node_opts_by_path(),
which returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 9c1a5077fd ("input: Rewrite sparcspkr device probing.")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220516081018.42728-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e4920d42ce0e9c8aafb7f64b6d9d4ae02161e51e upstream.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c8035 ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26623eea0da3476446909af96c980768df07bbd9 ]
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stmfts_input_open, so we should fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220317131604.53538-1-zhengyongjun3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 409353cbe9fe48f6bc196114c442b1cff05a39bc ]
Update input_set_capability() to prevent kernel panic in case the
event code exceeds the bitmap for the given event type.
Suggested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220320032537.545250-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fd269e74f2feec973f45ee11d822faeda4fe284 ]
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8b188fba75195745026e11d408e4a7e94e01d701 upstream.
This reverts commit 37ef4c19b4c659926ce65a7ac709ceaefb211c40.
The touchpad present in the Dell Precision 7550 and 7750 laptops
reports a HID_DG_BUTTONTYPE of type MT_BUTTONTYPE_CLICKPAD. However,
the device is not a clickpad, it is a touchpad with physical buttons.
In order to fix this issue, a quirk for the device was introduced in
libinput [1] [2] to disable the INPUT_PROP_BUTTONPAD property:
[Precision 7x50 Touchpad]
MatchBus=i2c
MatchUdevType=touchpad
MatchDMIModalias=dmi:*svnDellInc.:pnPrecision7?50*
AttrInputPropDisable=INPUT_PROP_BUTTONPAD
However, because of the change introduced in 37ef4c19b4 ("Input: clear
BTN_RIGHT/MIDDLE on buttonpads") the BTN_RIGHT key bit is not mapped
anymore breaking the device right click button and making impossible to
workaround it in user space.
In order to avoid breakage on other present or future devices, revert
the patch causing the issue.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220321184404.20025-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e941dc13fd3717122207d74539ab95da07ef797f ]
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5600f6986628dde8881734090588474f54a540a8 upstream.
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba115adf61b36b8c167126425a62b0efc23f72c0 upstream.
Make the samsung-keypad driver explicitly depend on CONFIG_HAS_IOMEM, as it
calls devm_ioremap(). This prevents compile errors in some configs (e.g,
allyesconfig/randconfig under UML):
/usr/bin/ld: drivers/input/keyboard/samsung-keypad.o: in function `samsung_keypad_probe':
samsung-keypad.c:(.text+0xc60): undefined reference to `devm_ioremap'
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: anton ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20220225041727.1902850-1-davidgow@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b7762e37c95d9b965d16bb0e18dbd1fa2e2861 upstream.
Before these changes elan_suspend() would only disable the regulator
when device_may_wakeup() returns false; whereas elan_resume() would
unconditionally enable it, leading to an enable count imbalance when
device_may_wakeup() returns true.
This triggers the "WARN_ON(regulator->enable_count)" in regulator_put()
when the elan_i2c driver gets unbound, this happens e.g. with the
hot-plugable dock with Elan I2C touchpad for the Asus TF103C 2-in-1.
Fix this by making the regulator_enable() call also be conditional
on device_may_wakeup() returning false.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a36d8ce554b82b0a08e2b95d0bd44fcbff339b upstream.
elan_disable_power() is called conditionally on suspend, where as
elan_enable_power() is always called on resume. This leads to
an imbalance in the regulator's enable count.
Move the regulator_[en|dis]able() calls out of elan_[en|dis]able_power()
in preparation of fixing this.
No functional changes intended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-1-hdegoede@redhat.com
[dtor: consolidate elan_[en|dis]able() into elan_set_power()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 37ef4c19b4c659926ce65a7ac709ceaefb211c40 ]
Buttonpads are expected to map the INPUT_PROP_BUTTONPAD property bit
and the BTN_LEFT key bit.
As explained in the specification, where a device has a button type
value of 0 (click-pad) or 1 (pressure-pad) there should not be
discrete buttons:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/touchpad-windows-precision-touchpad-collection#device-capabilities-feature-report
However, some drivers map the BTN_RIGHT and/or BTN_MIDDLE key bits even
though the device is a buttonpad and therefore does not have those
buttons.
This behavior has forced userspace applications like libinput to
implement different workarounds and quirks to detect buttonpads and
offer to the user the right set of features and configuration options.
For more information:
https://gitlab.freedesktop.org/libinput/libinput/-/merge_requests/726
In order to avoid this issue clear the BTN_RIGHT and BTN_MIDDLE key
bits when the input device is register if the INPUT_PROP_BUTTONPAD
property bit is set.
Notice that this change will not affect udev because it does not check
for buttons. See systemd/src/udev/udev-builtin-input_id.c.
List of known affected hardware:
- Chuwi AeroBook Plus
- Chuwi Gemibook
- Framework Laptop
- GPD Win Max
- Huawei MateBook 2020
- Prestigio Smartbook 141 C2
- Purism Librem 14v1
- StarLite Mk II - AMI firmware
- StarLite Mk II - Coreboot firmware
- StarLite Mk III - AMI firmware
- StarLite Mk III - Coreboot firmware
- StarLabTop Mk IV - AMI firmware
- StarLabTop Mk IV - Coreboot firmware
- StarBook Mk V
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20220208174806.17183-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cf73ed894ee939d6706d65e0cd186e4a64e3af6d upstream.
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc7ec91718c49d938849697cfad98fcd9877cc26 upstream.
The spaceball.c module was not properly parsing the movement reports
coming from the device. The code read axis data as signed 16-bit
little-endian values starting at offset 2.
In fact, axis data in Spaceball movement reports are signed 16-bit
big-endian values starting at offset 3. This was determined first by
visually inspecting the data packets, and later verified by consulting:
http://spacemice.org/pdf/SpaceBall_2003-3003_Protocol.pdf
If this ever worked properly, it was in the time before Git...
Signed-off-by: Leo L. Schwab <ewhac@ewhac.org>
Link: https://lore.kernel.org/r/20211221101630.1146385-1-ewhac@ewhac.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f3ccdc3f6ef10084ceb3a47df0961bec6196fd0 upstream.
Syzbot has reported warning in __flush_work(). This warning is caused by
work->func == NULL, which means missing work initialization.
This may happen, since input_dev->close() calls
cancel_work_sync(&dev->work), but dev->work initalization happens _after_
input_register_device() call.
So this patch moves dev->work initialization before registering input
device
Fixes: 5a6eb676d3 ("Input: appletouch - improve powersaving for Geyser3 devices")
Reported-and-tested-by: syzbot+b88c5eae27386b252bbd@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20211230141151.17300-1-paskripkin@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44ee250aeeabb28b52a10397ac17ffb8bfe94839 ]
The ASUS UM325UA suffers from the same issue as the ASUS UX425UA, which
is a very similar laptop. The i8042 device is not usable immediately
after boot and fails to initialize, requiring a deferred retry.
Enable the deferred probe quirk for the UM325UA.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211204015615.232948-1-samuel@cavoj.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9222ba68c3f4065f6364b99cc641b6b019ef2d42 ]
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 81e818869be522bc8fa6f7df1b92d7e76537926c upstream.
Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ebfee2bbc1a9c343dd50565ba5ae249fac32267 upstream.
The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12f247ab590a08856441efdbd351cf2cc8f60a2d upstream.
The "id_buf" buffer is stored in "data->raw_info_block" and freed by
"mxt_free_object_table" in case of error.
Return instead of jumping to avoid a double free.
Addresses-Coverity-ID: 1474582 ("Double free")
Fixes: 068bdb67ef ("Input: atmel_mxt_ts - fix the firmware update")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20211212194257.68879-1-jose.exposito89@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a02dcde595f7cbd240ccd64de96034ad91cffc40 upstream.
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16e28abb7290c4ca3b3a0f333ba067f34bb18c86 upstream.
Fujitsu Lifebook T725 laptop requires, like a few other similar
models, the nomux and notimeout options to probe the touchpad
properly. This patch adds the corresponding quirk entries.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1191980
Tested-by: Neal Gompa <ngompa13@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211103070019.13374-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be896bd3b72b44126c55768f14c22a8729b0992e upstream.
Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 744d0090a5f6dfa4c81b53402ccdf08313100429 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 4873586278 ("Input: iforce - use DMA-safe buffer when getting IDs from USB")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 5.3
Link: https://lore.kernel.org/r/20211025115501.5190-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d997cc1715df7b6c3df798881fb9941acf0079f8 ]
On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)
This completes the fix in commit 135be16d35 ("ARM: dts: imx7s: add
snvs clock to pwrkey").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211013062848.2667192-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3378a07daa6cdd11e042797454c706d1c69f9ca6 upstream.
The Nacon GX100XF is already mapped, but it seems there is a Nacon
GC-100 (identified as NC5136Wht PCGC-100WHITE though I believe other
colours exist) with a different USB ID when in XInput mode.
Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Link: https://lore.kernel.org/r/20211015192051.5196-1-michael@michaelcullen.name
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cac7100d4c51c04979dacdfe6c9a5e400d3f0a27 ]
Inside function hideep_nvm_unlock(), variable "unmask_code" could
be uninitialized if hideep_pgm_r_reg() returns error, however, it
is used in the later if statement after an "and" operation, which
is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9b576917a1d0efa293801a264150a1b37691617 ]
Return error code -EINVAL rather than '0' when the combo devices are not
supported.
Fixes: fa71c605c2 ("Input: combine hil_kbd and hil_ptr drivers")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210515030053.6824-1-thunder.leizhen@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a6f0dbe621a5c20dc912ac474debf9f11129e03 ]
Move the DMI quirks for upside-down mounted Goodix touchscreens from
drivers/input/touchscreen/goodix.c to
drivers/platform/x86/touchscreen_dmi.c,
where all the other x86 touchscreen quirks live.
Note the touchscreen_dmi.c code attaches standard touchscreen
device-properties to an i2c-client device based on a combination of a
DMI match + a device-name match. I've verified that the: Teclast X98 Pro,
WinBook TW100 and WinBook TW700 uses an ACPI devicename of "GDIX1001:00"
based on acpidumps and/or dmesg output available on the web.
This patch was tested on a Teclast X89 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210504185746.175461-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f8f84af5da9ee04ef1d271528656dac42a090d00 upstream.
Even though we validate user-provided inputs we then traverse past
validated data when applying the new map. The issue was originally
discovered by Murray McAllister with this simple POC (if the following
is executed by an unprivileged user it will instantly panic the system):
int main(void) {
int fd, ret;
unsigned int buffer[10000];
fd = open("/dev/input/js0", O_RDONLY);
if (fd == -1)
printf("Error opening file\n");
ret = ioctl(fd, JSIOCSBTNMAP & ~IOCSIZE_MASK, &buffer);
printf("%d\n", ret);
}
The solution is to traverse internal buffer which is guaranteed to only
contain valid date when constructing the map.
Fixes: 182d679b2298 ("Input: joydev - prevent potential read overflow in ioctl")
Fixes: 999b874f4a ("Input: joydev - validate axis/button maps before clobbering current ones")
Reported-by: Murray McAllister <murray.mcallister@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alexander Larkin <avlarkin82@gmail.com>
Link: https://lore.kernel.org/r/20210620120030.1513655-1-avlarkin82@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41e81022a04a0294c55cfa7e366bc14b9634c66e upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the four control requests which erroneously used usb_rcvctrlpipe().
Fixes: 1d3e20236d ("[PATCH] USB: usbtouchscreen: unified USB touchscreen driver")
Fixes: 24ced062a2 ("usbtouchscreen: add support for DMC TSC-10/25 devices")
Fixes: 9e3b25837a ("Input: usbtouchscreen - add support for e2i touchscreen controller")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.17
Link: https://lore.kernel.org/r/20210524092048.4443-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e479187748a8f151a85116a7091c599b121fdea5 ]
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
[ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[ 55.373593] i2c_designware 808622C1:04: controller timed out
[ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65299e8bfb24774e6340e93ae49f6626598917c8 ]
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
[ 0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator
[ 0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator
[ 0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121
[ 0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121
[ 0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff
[ 1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121
[ 1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207759
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202756.16830-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ac05a8a927e5a1027592d8f98510a511dadeed14 upstream.
This adds the negation needed for proper finger detection on Ilitek
ili2107/ili210x. This fixes polling issues (on Amazon Kindle Fire)
caused by returning false for the cooresponding finger on the touchscreen.
Signed-off-by: Hansem Ro <hansemro@outlook.com>
Fixes: e3559442af ("ili210x - rework the touchscreen sample processing")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit daa58c8eec0a65ac8e2e77ff3ea8a233d8eec954 upstream.
The Zenbook Flip entry that was added overwrites a previous one
because of a typo:
In file included from drivers/input/serio/i8042.h:23,
from drivers/input/serio/i8042.c:131:
drivers/input/serio/i8042-x86ia64io.h:591:28: error: initialized field overwritten [-Werror=override-init]
591 | .matches = {
| ^
drivers/input/serio/i8042-x86ia64io.h:591:28: note: (near initialization for 'i8042_dmi_noselftest_table[0].matches')
Add the missing separator between the two.
Fixes: b5d6e7ab7fe7 ("Input: i8042 - add ASUS Zenbook Flip to noselftest list")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Link: https://lore.kernel.org/r/20210323130623.2302402-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30b3f68715595dee7fe4d9bd91a2252c3becdf0a upstream.
The touch coordinate register contains the following:
byte 3 byte 2 byte 1
+--------+--------+ +-----------------+ +-----------------+
| | | | | | |
| X[3:0] | Y[3:0] | | Y[11:4] | | X[11:4] |
| | | | | | |
+--------+--------+ +-----------------+ +-----------------+
Bytes 2 and 1 need to be shifted left by 4 bits, the least significant
nibble of each is stored in byte 3. Currently they are only
being shifted by 3 causing the reported coordinates to be incorrect.
This matches downstream examples, and has been confirmed on my
device (OnePlus 7 Pro).
Fixes: 0145a7141e ("Input: add support for the Samsung S6SY761 touchscreen")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20210305185710.225168-1-caleb@connolly.tech
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69d5ff3e9e51e23d5d81bf48480aa5671be67a71 ]
The driver registers an interrupt handler in _probe, but didn't configure
them until later when the _open function is called. In between, the keypad
can fire an IRQ due to touchpad activity, which the handler ignores. This
causes the kernel to disable the interrupt, blocking the keypad from
working.
Fix this by disabling interrupts before registering the handler.
Additionally, disable them in _close, so that they're only enabled while
open.
Fixes: fc4f314618 ("Input: add TI-Nspire keypad support")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/3383725.iizBOSrK1V@linux-e202.suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ce1ac23149c6da939a5926c098c270c58c317a0 ]
The response to a command may never arrive or it may be corrupted (and
hence dropped) for some reason. While exceedingly rare, when it did
happen it blocked all further commands. One way to fix this was to
do a suspend/resume. However, recovering automatically seems like a
nicer option. Hence this puts a time limit (1 sec) on how long we're
willing to wait for a response, after which we assume it got lost.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Link: https://lore.kernel.org/r/20210217190718.11035-1-ronald@innovation.ch
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 056115daede8d01f71732bc7d778fb85acee8eb6 upstream.
The 0x5F is a new trackpoint report type used by some modules.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071511.32349-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Nikolai Kostrigin <nickel@basealt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4c9062717feda88900b566463228d1c4910af6d upstream.
There are some version of Elan trackpads that send incorrect data when
in SMbus mode, unless they are switched to use 0x5f reports instead of
standard 0x5e. This patch implements querying device to retrieve chips
identifying data, and switching it, when needed to the alternative
report.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071531.32413-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5d6e7ab7fe7d186878142e9fc1a05e4c3b65eb9 upstream.
After commit 77b425399f ("Input: i8042 - use chassis info to skip
selftest on Asus laptops"), all modern Asus laptops have the i8042
selftest disabled. It has done by using chassys type "10" (laptop).
The Asus Zenbook Flip suffers from similar suspend/resume issues, but
it _sometimes_ work and sometimes it doesn't. Setting noselftest makes
it work reliably. In this case, we need to add chassis type "31"
(convertible) in order to avoid selftest in this device.
Reported-by: Ludvig Norgren Guldhag <ludvigng@gmail.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Link: https://lore.kernel.org/r/20210219164638.761-1-mpdesouza@suse.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 182d679b2298d62bf42bb14b12a8067b8e17b617 upstream.
The problem here is that "len" might be less than "joydev->nabs" so the
loops which verfy abspam[i] and keypam[] might read beyond the buffer.
Fixes: 999b874f4a ("Input: joydev - validate axis/button maps before clobbering current ones")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YCyzR8WvFRw4HWw6@mwanda
[dtor: additional check for len being even in joydev_handle_JSIOCSBTNMAP]
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0958351e93fa0ac142f6dd8bd844441594f30a57 ]
If elo_setup_10() fails then this should return an error code instead
of success.
Fixes: fae3006e4b ("Input: elo - add support for non-pressure-sensitive touchscreens")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKFd5CvDu+jVmfW@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b7d2815839024e5181bd2572f5d8d4f65363b3 ]
If v4l2_ctrl_handler_setup() fails then probe() should return an error
code instead of returning success.
Fixes: cee1e3e2ef ("media: add video control handlers using V4L2 control framework")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKFkbATXa5fA3xj@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b830a9c34d5897be07176ce4e6f2d75e2c8cfd7 ]
The tty line discipline .read() function was passed the final user
pointer destination as an argument, which doesn't match the 'write()'
function, and makes it very inconvenient to do a splice method for
ttys.
This is a conversion to use a kernel buffer instead.
NOTE! It does this by passing the tty line discipline ->read() function
an additional "cookie" to fill in, and an offset into the cookie data.
The line discipline can fill in the cookie data with its own private
information, and then the reader will repeat the read until either the
cookie is cleared or it runs out of data.
The only real user of this is N_HDLC, which can use this to handle big
packets, even if the kernel buffer is smaller than the whole packet.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 60159e9e7bc7e528c103b6b6d47dfd83af29669c upstream.
The ILI251x seems to report pressure information in the 5th byte of
each per-finger touch data element. On the available hardware, this
information has the values ranging from 0x0 to 0xa, which is also
matching the downstream example code. Report pressure information
on the ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201224071238.160098-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bbd77d5bbc9aff8cb74d805c31751f5f0691ba8 upstream.
There is a fork of this driver on GitHub [0] that has been updated
with new device IDs.
Merge those into the mainline driver, so the out-of-tree fork is not
needed for users of those devices anymore.
[0] https://github.com/paroj/xpad
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Link: https://lore.kernel.org/r/20210121142523.1b6b050f@rechenknecht2k11
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dce6db70c77bbe639f5cd9cc796fb8f2694a7d0 upstream.
The Goodix GT9286 is a capacitive touch sensor IC based on GT1x.
This chip can be found on a number of smartphones, including the
F(x)tec Pro 1 and the Elephone U.
This has been tested on F(x)Tec Pro1 (MSM8998).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210109135512.149032-2-angelogioacchino.delregno@somainline.org
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f051ae4f6c732c231046945b36234e977f8467c6 upstream.
gcc -Warray-bounds warns about a serious bug in
cyapa_pip_retrieve_data_structure:
drivers/input/mouse/cyapa_gen6.c: In function 'cyapa_pip_retrieve_data_structure.constprop':
include/linux/unaligned/access_ok.h:40:17: warning: array subscript -1 is outside array bounds of 'struct retrieve_data_struct_cmd[1]' [-Warray-bounds]
40 | *((__le16 *)p) = cpu_to_le16(val);
drivers/input/mouse/cyapa_gen6.c:569:13: note: while referencing 'cmd'
569 | } __packed cmd;
| ^~~
Apparently the '-2' was added to the pointer instead of the value,
writing garbage into the stack next to this variable.
Fixes: c2c06c41f7 ("Input: cyapa - add gen6 device module support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161332.3708389-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59bbf83835f591b95c3bdd09d900f3584fa227af ]
In omap4_keypad_probe, the patch fix several bugs.
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) In err_unmap, forget to disable runtime of device,
pm_runtime_enable will increase power disable depth. Thus a
pairing decrement is needed on the error handling path to keep
it balanced.
3) In err_pm_disable, it will call pm_runtime_put_sync twice not
one time.
To fix this we factor out code reading revision and disabling touchpad, and
drop PM reference once we are done talking to the device.
Fixes: f77621cc64 ("Input: omap-keypad - dynamically handle register offsets")
Fixes: 5ad567ffba ("Input: omap4-keypad - wire up runtime PM handling")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201120133918.2559681-1-zhangqilong3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03e2c9c782f721b661a0e42b1b58f394b5298544 ]
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820830ec918f6c3dcd77a54a1c6198ab57407916 ]
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e52cd628a03f72a547dbf90ccb703ee64800504a ]
If touchscreen is released while busy reading HWMON device, the release
can be missed. The IRQ thread is not started because no touch is active
and BTN_TOUCH release event is never sent.
Fixes: f5a28a7d48 ("Input: ads7846 - avoid pen up/down when reading hwmon")
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201027105416.18773-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull input fixes from Dmitry Torokhov:
- a fix for cm109 stomping on its own control URB if it tries to toggle
buzzer immediately after userspace opens input device (found by
syzcaller)
- another fix for Raydium touchscreens that do not like splitting
command transfers
- quirks for i8042, soc_button_array, and goodix drivers to make them
work better with certain hardware.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - add upside-down quirk for Teclast X98 Pro tablet
Input: cm109 - do not stomp on control URB
Input: i8042 - add Acer laptops to the i8042 reset list
Input: cros_ec_keyb - send 'scancodes' in addition to key events
Input: soc_button_array - add Lenovo Yoga Tablet2 1051L to the dmi_use_low_level_irq list
Input: raydium_ts_i2c - do not split tx transactions
The touchscreen on the Teclast x98 Pro is also mounted upside-down in
relation to the display orientation.
Signed-off-by: Simon Beginn <linux@simonmicro.de>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20201117004253.27A5A27EFD@localhost
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to make sure we are not stomping on the control URB that was
issued when opening the device when attempting to toggle buzzer.
To do that we need to mark it as pending in cm109_open().
Reported-and-tested-by: syzbot+150f793ac5bc18eee150@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad operates in Basic Mode by default in the Acer BIOS
setup, but some Aspire/TravelMate models require the i8042 to be
reset in order to be correctly detected.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Link: https://lore.kernel.org/r/20201207071250.15021-1-chiu@endlessos.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To let userspace know what 'scancodes' should be used in EVIOCGKEYCODE
and EVIOCSKEYCODE ioctls, we should send EV_MSC/MSC_SCAN events in
addition to EV_KEY/KEY_* events. The driver already declared MSC_SCAN
capability, so it is only matter of actually sending the events.
Link: https://lore.kernel.org/r/X87aOaSptPTvZ3nZ@google.com
Acked-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the Lenovo Yoga Tablet2 1051L to the list of devices where the
ACPI AML code is poking the GPIO config register directly changing
the IRQ type to a low_level_irq, which we need to work around.
This fixes the home button on the Lenovo Yoga Tablet2 1051L not
working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201206161245.24798-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Raydium device does not like splitting of tx transactions into multiple
messages - one for the register address and one for the actual data. This
results in incorrect behavior on the device side.
This change updates raydium_i2c_read and raydium_i2c_write to create
i2c_msg arrays separately and passes those arrays into raydium_i2c_xfer
which decides based on the address whether the bank switch command should
be sent. The bank switch header is still added by raydium_i2c_read and
raydium_i2c_write to ensure that all these operations are performed as part
of a single I2C transfer. It guarantees that no other transactions are
initiated to any other device on the same bus after the bank switch command
is sent.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Link: https://lore.kernel.org/r/20201205005941.1427643-1-furquan@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix for 'RETRIGEN' handling in Atmel touch controllers that was
causing lost interrupts on systems using edge-triggered interrupts, a
quirk for i8042 driver, and a couple more fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - fix lost interrupts
Input: xpad - support Ardwiino Controllers
Input: i8042 - add ByteSpeed touchpad to noloop table
Input: i8042 - fix error return code in i8042_setup_aux()
Input: soc_button_array - add missing include
