[ Upstream commit db19d3aa77612983a02bd223b3f273f896b243cf ]
There is a race condition in the CMT interrupt handler. In the interrupt
handler the driver sets a driver private flag, FLAG_IRQCONTEXT. This
flag is used to indicate any call to set_next_event() should not be
directly propagated to the device, but instead cached. This is done as
the interrupt handler itself reprograms the device when needed before it
completes and this avoids this operation to take place twice.
It is unclear why this design was chosen, my suspicion is to allow the
struct clock_event_device.event_handler callback, which is called while
the FLAG_IRQCONTEXT is set, can update the next event without having to
write to the device twice.
Unfortunately there is a race between when the FLAG_IRQCONTEXT flag is
set and later cleared where the interrupt handler have already started to
write the next event to the device. If set_next_event() is called in
this window the value is only cached in the driver but not written. This
leads to the board to misbehave, or worse lockup and produce a splat.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 0-...!: (0 ticks this GP) idle=f5e0/0/0x0 softirq=519/519 fqs=0 (false positive?)
rcu: (detected by 1, t=6502 jiffies, g=-595, q=77 ncpus=2)
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.10.0-rc5-arm64-renesas-00019-g74a6f86eaf1c-dirty #20
Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : tick_check_broadcast_expired+0xc/0x40
lr : cpu_idle_poll.isra.0+0x8c/0x168
sp : ffff800081c63d70
x29: ffff800081c63d70 x28: 00000000580000c8 x27: 00000000bfee5610
x26: 0000000000000027 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00007fbb9100 x22: ffff8000818f1008 x21: ffff8000800ef07c
x20: ffff800081c79ec0 x19: ffff800081c70c28 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffc2c717d8
x14: 0000000000000000 x13: ffff000009c18080 x12: ffff8000825f7fc0
x11: 0000000000000000 x10: ffff8000818f3cd4 x9 : 0000000000000028
x8 : ffff800081c79ec0 x7 : ffff800081c73000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : ffff7ffffe286000 x3 : 0000000000000000
x2 : ffff7ffffe286000 x1 : ffff800082972900 x0 : ffff8000818f1008
Call trace:
tick_check_broadcast_expired+0xc/0x40
do_idle+0x9c/0x280
cpu_startup_entry+0x34/0x40
kernel_init+0x0/0x11c
do_one_initcall+0x0/0x260
__primary_switched+0x80/0x88
rcu: rcu_preempt kthread timer wakeup didn't happen for 6501 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
rcu: Possible timer handling issue on cpu=0 timer-softirq=262
rcu: rcu_preempt kthread starved for 6502 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 flags:0x00000008
Call trace:
__switch_to+0xbc/0x100
__schedule+0x358/0xbe0
schedule+0x48/0x148
schedule_timeout+0xc4/0x138
rcu_gp_fqs_loop+0x12c/0x764
rcu_gp_kthread+0x208/0x298
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
The design have been part of the driver since it was first merged in
early 2009. It becomes increasingly harder to trigger the issue the
older kernel version one tries. It only takes a few boots on v6.10-rc5,
while hundreds of boots are needed to trigger it on v5.10.
Close the race condition by using the CMT channel lock for the two
competing sections. The channel lock was added to the driver after its
initial design.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20240702190230.3825292-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d3bc4c02d59996d1d3180d8ed409a9d7d5900e0 ]
On SAM9 hardware two cascaded 16 bit timers are used to form a 32 bit
high resolution timer that is used as scheduler clock when the kernel
has been configured that way (CONFIG_ATMEL_CLOCKSOURCE_TCB).
The driver initially triggers a reset-to-zero of the two timers but this
reset is only performed on the next rising clock. For the first timer
this is ok - it will be in the next 60ns (16MHz clock). For the chained
second timer this will only happen after the first timer overflows, i.e.
after 2^16 clocks (~4ms with a 16MHz clock). So with other words the
scheduler clock resets to 0 after the first 2^16 clock cycles.
It looks like that the scheduler does not like this and behaves wrongly
over its lifetime, e.g. some tasks are scheduled with a long delay. Why
that is and if there are additional requirements for this behaviour has
not been further analysed.
There is a simple fix for resetting the second timer as well when the
first timer is reset and this is to set the ATMEL_TC_ASWTRG_SET bit in
the Channel Mode register (CMR) of the first timer. This will also rise
the TIOA line (clock input of the second timer) when a software trigger
respective SYNC is issued.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231007161803.31342-1-rwahl@gmx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b5bf64c89c7100c921bd807ba39b2eb003061ab ]
Smatch reports:
drivers/clocksource/timer-cadence-ttc.c:529 ttc_timer_probe()
warn: 'timer_baseaddr' from of_iomap() not released on lines: 498,508,516.
timer_baseaddr may have the problem of not being released after use,
I replaced it with the devm_of_iomap() function and added the clk_put()
function to cleanup the "clk_ce" and "clk_cs".
Fixes: e932900a32 ("arm: zynq: Use standard timer binding")
Fixes: 70504f311d ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Signed-off-by: Feng Mingxi <m202271825@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230425065611.702917-1-m202271825@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb73556386e074e9bee9fa2d253aeaefe4e063e0 ]
Smatch reports:
drivers/clocksource/timer-davinci.c:332 davinci_timer_register()
warn: 'base' from ioremap() not released on lines: 274.
Fix this and other potential memory leak problems
by adding a set of corresponding exit lables.
Fixes: 721154f972 ("clocksource/drivers/davinci: Add support for clockevents")
Signed-off-by: Qinrun Dai <flno@hust.edu.cn>
Link: https://lore.kernel.org/r/20230413135037.1505799-1-flno@hust.edu.cn
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 180d35a7c05d520314a590c99ad8643d0213f28b ]
If clk_get_rate() fails which is called after clk_prepare_enable(),
clk_disable_unprepare() need be called in error path to disable the
clock in dmtimer_systimer_init_clock().
Fixes: 52762fbd1c ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221029114427.946520-1-yangyingliang@huawei.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f44f7156f59cae06e9160eafb5d8b2dfd09e639 ]
Documentation for most CMTs say that it takes two input clocks before
changes propagate to the timer. This is especially relevant when the timer
is stopped to change further settings.
Implement the delays according to the spec. To avoid unnecessary delays in
atomic mode, also check if the to-be-written value actually differs.
CMCNT is a bit special because testing showed that it requires 3 cycles to
propagate, which affects all CMTs. Also, the WRFLAG needs to be checked
before writing. This fixes "cannot clear CMCNT" messages which occur often
on R-Car Gen4 SoCs, but only very rarely on older SoCs for some reason.
Fixes: 81b3b27110 ("clocksource: sh_cmt: Add support for multiple channels per device")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20221130210609.7718-1-wsa+renesas@sang-engineering.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a97d55333e4299f32c98cca6dc5c4db1c5855fc ]
The Renesas Compare Match Timer 0 and 1 (CMT0/1) variants have a
register to control the clock supply to the individual channels.
Currently the driver does not touch this register, and relies on the
documented initial value, which has the clock supply enabled for all
channels present.
However, when Linux starts on the APE6-EVM development board, only the
clock supply to the first CMT1 channel is enabled. Hence the first
channel (used as a clockevent) works, while the second channel (used as
a clocksource) does not. Note that the default system clocksource is
the Cortex-A15 architectured timer, and the user needs to manually
switch to the CMT1 clocksource to trigger the broken behavior.
Fix this by removing the fragile dependency on implicit reset and/or
boot loader state, and by enabling the clock supply explicitly for all
channels used instead. This requires postponing the clk_disable() call,
else the timer's registers cannot be accessed in sh_cmt_setup_channel().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210194648.2901899-1-geert+renesas@glider.be
Stable-dep-of: 3f44f7156f59 ("clocksource/drivers/sh_cmt: Access registers according to spec")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9f15a9de44affe733e34f93bc184945ba277e6d ]
This reverts commit 232ccac1bd9b5bfe73895f527c08623e7fa0752d.
On the subject of suspend, the RISC-V SBI spec states:
This does not cover whether any given events actually reach the hart or
not, just what the hart will do if it receives an event. On PolarFire
SoC, and potentially other SiFive based implementations, events from the
RISC-V timer do reach a hart during suspend. This is not the case for the
implementation on the Allwinner D1 - there timer events are not received
during suspend.
To fix this, the CLOCK_EVT_FEAT_C3STOP (mis)feature was enabled for the
timer driver - but this has broken both RCU stall detection and timers
generally on PolarFire SoC and potentially other SiFive based
implementations.
If an AXI read to the PCIe controller on PolarFire SoC times out, the
system will stall, however, with CLOCK_EVT_FEAT_C3STOP active, the system
just locks up without RCU stalling:
io scheduler mq-deadline registered
io scheduler kyber registered
microchip-pcie 2000000000.pcie: host bridge /soc/pcie@2000000000 ranges:
microchip-pcie 2000000000.pcie: MEM 0x2008000000..0x2087ffffff -> 0x0008000000
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: axi read request error
microchip-pcie 2000000000.pcie: axi read timeout
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
Freeing initrd memory: 7332K
Similarly issues were reported with clock_nanosleep() - with a test app
that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250 & the blamed
commit in place, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Fortunately, the D1 has a second timer, which is "currently used in
preference to the RISC-V/SBI timer driver" so a revert here does not
hurt operation of D1 in its current form.
Ultimately, a DeviceTree property (or node) will be added to encode the
behaviour of the timers, but until then revert the addition of
CLOCK_EVT_FEAT_C3STOP.
Fixes: 232ccac1bd9b ("clocksource/drivers/riscv: Events are stopped during CPU suspend")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/
Link: https://github.com/riscv-non-isa/riscv-sbi-doc/issues/98/
Link: https://lore.kernel.org/linux-riscv/bf6d3b1f-f703-4a25-833e-972a44a04114@sholland.org/
Link: https://lore.kernel.org/r/20221122121620.3522431-1-conor.dooley@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
ixp4xx_timer_setup is exported, and so can not be an __init function.
But it does not need to be exported as it is only called from one
in-kernel function, so just remove the EXPORT_SYMBOL_GPL() marking to
resolve the build warning.
This is fixed "properly" in commit 41929c9f628b
("clocksource/drivers/ixp4xx: Drop boardfile probe path") but that can
not be backported to older kernels as the reworking of the IXP4xx
codebase is not suitable for stable releases.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 245b993d8f6c4e25f19191edfbd8080b645e12b1 ]
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
arch/x86/kernel/cpu/mshyperv.c is never compiled as modular.
(CONFIG_HYPERVISOR_GUEST is boolean)
Fixes: dd2cb34861 ("clocksource/drivers: Continue making Hyper-V clocksource ISA agnostic")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220606050238.4162200-1-masahiroy@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a98399cbc1e05f7b977419f03905501d566cf54e ]
When a machine sports more than one SP804 timer instance, we only bring
up the first one, since multiple timers of the same kind are not useful
to Linux. As this is intentional behaviour, we should not return an
error message, as we do today:
===============
[ 0.000800] Failed to initialize '/bus@8000000/motherboard-bus@8000000/iofpga-bus@300000000/timer@120000': -22
===============
Replace the -EINVAL return with a debug message and return 0 instead.
Also we do not reach the init function anymore if the DT node is
disabled (as this is now handled by OF_DECLARE), so remove the explicit
check for that case.
This fixes a long standing bogus error when booting ARM's fastmodels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220506162522.3675399-1-andre.przywara@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 232ccac1bd9b5bfe73895f527c08623e7fa0752d ]
Some implementations of the SBI time extension depend on hart-local
state (for example, CSRs) that are lost or hardware that is powered
down when a CPU is suspended. To be safe, the clockevents driver
cannot assume that timer IRQs will be received during CPU suspend.
Fixes: 62b0194368 ("clocksource: new RISC-V SBI timer driver")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20220509012121.40031-1-samuel@sholland.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a861abceecb68497dd82a324fee45a5332dcece ]
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
The __setup() handler interface isn't meant to handle negative return
values -- they are non-zero, so they mean "handled" (like a return
value of 1 does), but that's just a quirk. So return 1 from
parse_pmtmr(). Also print a warning message if kstrtouint() returns
an error.
Fixes: 6b148507d3 ("pmtmr: allow command line override of ioport")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4467b8bad2401794fb89a0268c8c8257180bf60f ]
of_base->base can either be iomapped using of_io_request_and_map() or
of_iomap() depending whether or not an of_base->name has been set.
Thus check of_base->base against NULL as of_iomap() does not return a
PTR_ERR() in case of error.
Fixes: 9aea417afa ("clocksource/drivers/timer-of: Don't request the resource by name")
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://lore.kernel.org/r/20220307172656.4836-1-granquet@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab8da93dc06d82f464c47ab30e6c75190702f369 ]
The driver statically defines maximum number of interrupts it can
handle, however it does not respect that limit when configuring them.
When provided with a DTS with more interrupts than assumed, the driver
will overwrite static array mct_irqs leading to silent memory
corruption.
Validate the interrupts coming from DTS to avoid this. This does not
change the fact that such DTS might not boot at all, because it is
simply incompatible, however at least some warning will be printed.
Fixes: 36ba5d527e ("ARM: EXYNOS: add device tree support for MCT controller driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220220103815.135380-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cd925a8823d16de5614d3f0aabea9948747accd ]
Move interrupts allocation from exynos4_timer_resources() into separate
function together with the interrupt number parsing code from
mct_init_dt(), so the code for managing interrupts is kept together.
While touching exynos4_timer_resources() function, move of_iomap() to it.
No functional changes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211101193531.15078-2-semen.protsenko@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8840f5460a23759403f1f2860429dcbcc2f04a65 ]
Devkit8000 board seems to always used 32k_counter as clocksource.
Restore this behavior.
If clocksource is back to 32k_counter, timer12 is now the clockevent
source (as before) and timer2 is not longer needed here.
This commit fixes the same issue observed with commit 23885389dbbb
("ARM: dts: Fix timer regression for beagleboard revision c") when sleep
is blocked until hitting keys over serial console.
Fixes: aba1ad05da ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23885389dbbbbc698986e77a45c1fc44a6e3632e ]
Commit e428e250fd ("ARM: dts: Configure system timers for omap3")
caused a timer regression for beagleboard revision c where the system
clockevent stops working if omap3isp module is unloaded.
Turns out we still have beagleboard revisions a-b4 capacitor c70 quirks
applied that limit the usable timers for no good reason. This also affects
the power management as we use the system clock instead of the 32k clock
source.
Let's fix the issue by adding a new omap3-beagle-ab4.dts for the old timer
quirks. This allows us to remove the timer quirks for later beagleboard
revisions. We also need to update the related timer quirk check for the
correct compatible property.
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Cc: linux-kernel@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eda9a4f7af6ee47e9e131f20e4f8a41a97379293 ]
When building OMAP_DM_TIMER without TIMER_OF, there are orphan sections
due to the use of TIMER_OF_DELCARE() without CONFIG_TIMER_OF. Select
CONFIG_TIMER_OF when enaling OMAP_DM_TIMER:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ti-dm-systimer.o' being placed in section `__timer_of_table'
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202108282255.tkdt4ani-lkp@intel.com/
Cc: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Fixes: 52762fbd1c ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210828175747.3777891-1-keescook@chromium.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be83c3b6e7b8ff22f72827a613bf6f3aa5afadbb ]
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55 ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8b33dfe0ba1c84c1aab2456590b38195837f1e6e upstream.
Bad counter reads are experienced sometimes when bit 10 or greater rolls
over. Originally, testing showed that at least 10 lower bits would be
set to the same value during these bad reads. However, some users still
reported time skips.
Wider testing revealed that on some chips, occasionally only the lowest
9 bits would read as the anomalous value. During these reads (which
still happen only when bit 10), bit 9 would read as the correct value.
Reduce the mask by one bit to cover these cases as well.
Cc: stable@vger.kernel.org
Fixes: c950ca8c35 ("clocksource/drivers/arch_timer: Workaround for Allwinner A64 timer instability")
Reported-by: Roman Stratiienko <r.stratiienko@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210515021439.55316-1-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9517c577f9f722270584cfb1a7b4e1354e408658 ]
As we are using cpu_pm to save and restore context, we must also save and
restore the timer sysconfig register TIOCP_CFG. This is needed because
we are not calling PM runtime functions at all with cpu_pm.
Fixes: b34677b099 ("clocksource/drivers/timer-ti-dm: Implement cpu_pm notifier for context save and restore")
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210415085506.56828-1-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 25de4ce5ed02994aea8bc111d133308f6fd62566 upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
Let's do this as a single patch so it can be backported to v5.8 and later
kernels easily. Note that this patch depends on earlier timer-ti-dm
systimer posted mode fixes, and a preparatory clockevent patch
"clocksource/drivers/timer-ti-dm: Prepare to handle dra7 timer wrap issue".
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210323074326.28302-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3efe7a878a11c13b5297057bfc1e5639ce1241ce upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm timers instead.
Let's prepare for adding support for percpu timers by adding a common
dmtimer_clkevt_init_common() and call it from dmtimer_clockevent_init().
This patch makes no intentional functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210323074326.28302-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a65f7e2772613debd03fa2492e76a635aa04545 ]
In case of error, the function device_node_to_regmap() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: ca7b72b5a5 ("clocksource: Add driver for the Ingenic JZ47xx OST")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210308123031.2285083-1-weiyongjun1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac4daf737674b4d29e19b7c300caff3bcf7160d8 ]
To avoid spurious timer interrupts when KTIME_MAX is used, we need to
configure set_state_oneshot_stopped(). Although implementing this is
optional, it still affects things like power management for the extra
timer interrupt.
For more information, please see commit 8fff52fd50 ("clockevents:
Introduce CLOCK_EVT_STATE_ONESHOT_STOPPED state") and commit cf8c5009ee
("clockevents/drivers/arm_arch_timer: Implement
->set_state_oneshot_stopped()").
Fixes: 52762fbd1c ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210304072135.52712-4-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 212709926c5493a566ca4086ad4f4b0d4e66b553 ]
When the timer is configured in posted mode, we need to check the write-
posted status register (TWPS) before writing to the register.
We now check TWPS after the write starting with commit 52762fbd1c
("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource
support").
For example, in the TRM for am571x the following is documented in chapter
"22.2.4.13.1.1 Write Posting Synchronization Mode":
"For each register, a status bit is provided in the timer write-posted
status (TWPS) register. In this mode, it is mandatory that software check
this status bit before any write access. If a write is attempted to a
register with a previous access pending, the previous access is discarded
without notice."
The regression happened when I updated the code to use standard read/write
accessors for the driver instead of using __omap_dm_timer_load_start().
We have__omap_dm_timer_load_start() check the TWPS status correctly using
__omap_dm_timer_write().
Fixes: 52762fbd1c ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210304072135.52712-2-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7da390694afbaed8e0f05717a541dfaf1077ba51 ]
When DEBUG is defined this error occurs
drivers/clocksource/mxs_timer.c:138:1: error:
expected ‘;’ before ‘}’ token
The preceding statement needs a semicolon.
Replace pr_info() with pr_debug() and remove the unneeded ifdef.
Fixes: eb8703e2ef ("clockevents/drivers/mxs: Migrate to new 'set-state' interface")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210118211955.763609-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a3b8758bd6e45f7b671723b5c9fa2b69d0787ae ]
Compile-testing the ixp4xx timer with CONFIG_OF enabled but
CONFIG_TIMER_OF disabled leads to a harmless warning:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ixp4xx.o' being placed in section `__timer_of_table'
Move the select statement from the platform code into the driver
so it always gets enabled in configurations that rely on it.
Fixes: 40df14cc5c ("clocksource/drivers/ixp4xx: Add OF initialization support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210103135955.3808976-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b7770b877d187bfdae1eaf587bd2b792479a31c ]
ARM virtual counter supports event stream, it can only trigger an event
when the trigger bit (the value of CNTKCTL_EL1.EVNTI) of CNTVCT_EL0 changes,
so the actual period of event stream is 2^(cntkctl_evnti + 1). For example,
when the trigger bit is 0, then virtual counter trigger an event for every
two cycles.
While we're at it, rework the way we compute the trigger bit position
by making it more obvious that when bits [n:n-1] are both set (with n
being the most significant bit), we pick bit (n + 1).
Fixes: 037f637767 ("drivers: clocksource: add support for ARM architected timer event stream")
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201204073126.6920-3-zhukeqian1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8cc3905b8073c7cfbff94af889fa8dc71f21dd5 ]
In commit 0ea415390c ("clocksource/arm_arch_timer: Use arch_timer_read_counter
to access stable counters"), we separate stable and normal count reader to omit
unnecessary overhead on systems that have no timer erratum.
However, in erratum_set_next_event_tval_generic(), count reader becomes normal
reader. This converts it to stable reader.
Fixes: 0ea415390c ("clocksource/arm_arch_timer: Use arch_timer_read_counter to access stable counters")
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201204073126.6920-2-zhukeqian1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab3105446f1ec4e98fadfc998ee24feec271c16c ]
The riscv timer is set via SBI timer call, let's make RISCV_TIMER
depends on RISCV_SBI, and it also fixes some build issue.
Fixes: d5be89a8d1 ("RISC-V: Resurrect the MMIO timer implementation for M-mode systems")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201028131230.72907-1-wangkefeng.wang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bd7cb29eceb52e4b108917786fdbf2a2c2048ef ]
The function ingenic_tcu_get_clock() is annotated for the __init
section but it is actually called from the online cpu callback.
That will lead to a crash if a CPU is hotplugged after boot time.
Remove the __init annotation for the ingenic_tcu_get_clock()
function.
Fixes: f19d838d08 (clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT)
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20201125102346.1816310-1-daniel.lezcano@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eee422c46e6840a81c9db18a497b74387a557b29 ]
If clk_notifier_register() failed, ttc_setup_clockevent() will return
without freeing 'ttcce', which will leak memory.
Fixes: 70504f311d ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201116135123.2164033-1-yukuai3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1e6cad00aa2f17845e7270e38ff3cc82c7b022a ]
After calling clk_prepare_enable(), clk_disable_unprepare() need
be called on error path.
Fixes: fbe4b3566d ("clocksource/drivers/orion: Convert init function...")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201111064706.3397156-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl+FqrsTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXnN8B/4sRg7j9OTzVBlDiXF2vj6vbuplTIH6
JR6S5f4PNjUg4gV6ghzSnsx1zqNhPSOr78zDqYto8vv+wqqj3thmld8+gAnSbKtt
yoAa7mhbbN1ryJiwPlZzvX4ApzGZPC7byqEi3+zPIcag6TEl8eyYJOmvY3x1zv8x
CsAb57oCC4erD0n4xlTyfuc8TLpO+EiU53PXbR9AovKQHe4m2/8LWyEbmrm5cRUR
gx8RxoLkkrqK0unzcmanbm47QodiaOTUpycs3IvaBeWZQsqSgFZdI1RAdTZNg+U+
GT8eMRXAwpgDpilPm/0n1O0PKGAsVh9Lbw8Btb/ggqnjTUlA4Z3Df23E
=Wy5n
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
Core:
- Early boot support for the NMI safe timekeeper by utilizing
local_clock() up to the point where timekeeping is initialized. This
allows printk() to store multiple timestamps in the ringbuffer which is
useful for coordinating dmesg information across a fleet of machines.
- Provide a multi-timestamp accessor for printk()
- Make timer init more robust by checking for invalid timer flags.
- Comma vs. semicolon fixes
Drivers:
- Support for new platforms in existing drivers (SP804 and Renesas CMT)
- Comma vs. semicolon fixes
-----BEGIN PGP SIGNATURE-----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=h6YX
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timekeeping updates from Thomas Gleixner:
"Updates for timekeeping, timers and related drivers:
Core:
- Early boot support for the NMI safe timekeeper by utilizing
local_clock() up to the point where timekeeping is initialized.
This allows printk() to store multiple timestamps in the ringbuffer
which is useful for coordinating dmesg information across a fleet
of machines.
- Provide a multi-timestamp accessor for printk()
- Make timer init more robust by checking for invalid timer flags.
- Comma vs semicolon fixes
Drivers:
- Support for new platforms in existing drivers (SP804 and Renesas
CMT)
- Comma vs semicolon fixes
* tag 'timers-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/armada-370-xp: Use semicolons rather than commas to separate statements
clocksource/drivers/mps2-timer: Use semicolons rather than commas to separate statements
timers: Mask invalid flags in do_init_timer()
clocksource/drivers/sp804: Enable Hisilicon sp804 timer 64bit mode
clocksource/drivers/sp804: Add support for Hisilicon sp804 timer
clocksource/drivers/sp804: Support non-standard register offset
clocksource/drivers/sp804: Prepare for support non-standard register offset
clocksource/drivers/sp804: Remove a mismatched comment
clocksource/drivers/sp804: Delete the leading "__" of some functions
clocksource/drivers/sp804: Remove unused sp804_timer_disable() and timer-sp804.h
clocksource/drivers/sp804: Cleanup clk_get_sys()
dt-bindings: timer: renesas,cmt: Document r8a774e1 CMT support
dt-bindings: timer: renesas,cmt: Document r8a7742 CMT support
alarmtimer: Convert comma to semicolon
timekeeping: Provide multi-timestamp accessor to NMI safe timekeeper
timekeeping: Utilize local_clock() for NMI safe timekeeper during early boot
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1601233948-11629-17-git-send-email-Julia.Lawall@inria.fr
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1601233948-11629-12-git-send-email-Julia.Lawall@inria.fr
clint_time_val will soon be used by the RISC-V implementation of
random_get_entropy(), which is a static inline function that may be used by
modules (at least CRYPTO_JITTERENTROPY=m).
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
- Reset the TI/DM timer before enabling it instead of doing it the other
way round.
- Initialize the reload value for the GX6605s timer correctly so the
hardware counter starts at 0 again after overrun.
- Make error return value negative in the h8300 timer init function
-----BEGIN PGP SIGNATURE-----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=Htin
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A set of clocksource/clockevents updates:
- Reset the TI/DM timer before enabling it instead of doing it the
other way round.
- Initialize the reload value for the GX6605s timer correctly so the
hardware counter starts at 0 again after overrun.
- Make error return value negative in the h8300 timer init function"
* tag 'timers-urgent-2020-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-gx6605s: Fixup counter reload
clocksource/drivers/timer-ti-dm: Do reset before enable
clocksource/drivers/h8300_timer8: Fix wrong return value in h8300_8timer_init()
A 100MHZ 32-bit timer will be wrapped up less than 43s. Although the
kernel maintains a software high 32-bit count in the tick IRQ. But it's
not applicable to the user mode APPs.
Note: The kernel still uses the lower 32 bits of the timer.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-9-thunder.leizhen@huawei.com
The ARM SP804 supports a maximum of 32-bit counter, but Hisilicon extends
it to 64-bit. That means, the registers: TimerXload, TimerXValue and
TimerXBGLoad are 64bits, all other registers are the same as those in the
SP804. The driver code can be completely reused except that the register
offset is different.
Use compatible = "hisilicon,sp804" mark as Hisilicon sp804 timer.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-8-thunder.leizhen@huawei.com
The ARM SP804 supports a maximum of 32-bit counter, but Hisilicon extends
it to 64-bit. That means, the registers: TimerXload, TimerXValue and
TimerXBGLoad are 64bits, all other registers are the same as those in the
SP804. The driver code can be completely reused except that the register
offset is different.
Currently, we get a timer register address by: add the constant register
offset to the timer base address. e.g. "base + TIMER_CTRL". It can not be
dynamically adjusted at run time.
So create a new structure "sp804_timer" to record the original registers
offset, and create a new structure "sp804_clkevt" to record the
calculated registers address. So the "base + TIMER_CTRL" is changed to
"clkevt->ctrl", this will faster than "base + timer->ctrl".
For example:
struct sp804_timer arm_sp804_timer = {
.ctrl = TIMER_CTRL,
};
struct sp804_clkevt clkevt;
clkevt.ctrl = base + arm_sp804_timer.ctrl.
- writel(0, base + TIMER_CTRL);
+ writel(0, clkevt->ctrl);
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-7-thunder.leizhen@huawei.com
