Add UTMI support for SAMA7G5. SAMA7G5's UTMI control is done via
XTALF register. Values written at bits 2..0 in this register
correspond to the on board crystal oscillator frequency.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-18-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some of the SAMA7G5 PLLs support multiple outputs (e.g. AUDIO PLL).
For these, split the PLL clock in two: fractional clock and
divider clock. In case PLLs supports multiple outputs (since these
outputs are dividers (with different settings) sharing the same
fractional part), it will register one fractional clock and multiple
divider clocks (dividers sharing the fractional clock).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-17-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some peripheral clocks on SAMA7G5 supports requesting parent to change
its rate (image related clocks: csi, csi2dc, isc). Add support
so that if registered with this option the clock rate to be
requested from parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-14-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add master clock support (MCK1..4) for SAMA7G5. SAMA7G5's PMC has
multiple master clocks feeding different subsystems. One of them
feeds image subsystem and is changeable based on image subsystem
needs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-13-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pass the ID of changeable parent at registration. This will allow
the scalability of this clock driver with regards to the changeable
parent ID for versions of this IP where changeable parent is not the
last one in the parents list (e.g. SAMA7G5). With this the clock flags
are set to zero in case we have no changeable parent. Also in
clk_generated_best_diff() the *best_diff variable is check against
tmp_diff variable using ">=" operator instead of ">" so that in case
the requested frequency could be obtained using fix parents + gck
dividers but the clock also supports changeable parent to be able
to force the usage of the changeable parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-11-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In commit a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
the fractional part of PLL wasn't set on registers but it was
calculated and taken into account for determining div and mul
(see sam9x60_pll_get_best_div_mul()).
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-7-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to datasheet the range of 600-1200MHz is for the
frequency generated by the fractional part of the PLL (namely
Fcorepllck according to datasheet). With this in mind the output
range of the PLL itself (fractional + div), taking into account
that the divider is 8 bits wide, is 600/256-1200Hz=2.3-1200MHz.
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use logical or for range check. In case bestrate is not in
characteristics->output[0].min..characteristics->output[0].max
range we should return -ERANGE.
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
__clk_determine_rate() may return error. Skip the current step
in case of error.
Fixes: 1a1a36d72e3d3 ("clk: at91: clk-generated: make gclk determine audio_pll rate")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
syscon_node_to_regmap() will make the created regmap get and enable the
first clock it can parse from the device tree. This clock is not needed to
access the registers and should not be enabled at that time.
Use device_node_to_regmap to resolve this as it looks up the regmap in
the same list but doesn't care about the clocks. This issue is detected
by lockdep when booting the sama5d3 with a device tree containing the
new clk bindings.
This fix already happened in 6956eb33abb5 ("clk: at91: fix possible
deadlock") for the drivers that had been migrated to the new clk binding
back then. This does the same for the new drivers as well.
Fixes: 01e2113de9a5 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200703073236.23923-1-a.fatoum@pengutronix.de
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For test and debug purposes, it's simple enough to enable or disable
clocks from shell. Add a new debugfs file 'clk_prepare_enable' that
calls clk_prepare_enable() when writing "1" and clk_disable_unprepare()
when writing "0".
This can have security implications, so only support it when the code
has been modified to #define CLOCK_ALLOW_WRITE_DEBUGFS.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200630003024.6282-1-mdtipton@codeaurora.org
[sboyd@kernel.org: Reword commit text and remove comment update]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Change from 'DIV_ROUND_UP' to 'DIV_ROUND_CLOSEST' when calculating the
clock divisor in the iProc ASIU clock driver to allow to get to the
closest clock rate.
Fixes: 5fe225c105fd ("clk: iproc: add initial common clock support")
Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Link: https://lore.kernel.org/r/20200612225212.124301-1-ray.jui@broadcom.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the graphics clock controller found on SM8250
based devices.
This is initially copied from the downstream kernel, but has
been modified to more closely match the upstream sc7180 driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-12-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the graphics clock controller found on SM8150
based devices.
This is initially copied from the downstream kernel, but has
been modified to more closely match the upstream sc7180 driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-11-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
All gpucc drivers need this, so move it to common code instead of
duplicating it in every gpucc driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-10-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The fixed alpha pll ops only use it for clamping in round_rate, which is
unnecessary. This is consistent with SM8250 GCC not using vco_table.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-6-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Lucid PCAL_DONE is different from trion.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-5-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixed ops were already identical, this adds support for non-fixed ops by
sharing between trion and lucid.
This also changes the names for trion ops to be consistent with the rest.
Note LUCID_PCAL_DONE is renamed to TRION_PCAL_DONE because it is wrong for
lucid, LUCID_PCAL_DONE should be BIT(27). Next patch will address this.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-4-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
0x44 isn't a register offset, it is the value that goes into CAL_L_VAL.
Fixes: 548a909597d5 ("clk: qcom: clk-alpha-pll: Add support for Trion PLLs")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-3-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix the parents and set BRANCH_HALT_SKIP. From the downstream driver it
should be a 500us delay and not skip, however this matches what was done
for other clocks that had 500us delay in downstream.
Fixes: f73a4230d5bb ("clk: qcom: gcc: Add GPU and NPU clocks for SM8150")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-2-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Reusing the generic struct vc5_hw_data for all blocks is handy. However it
implies we allocate space the div_int and div_frc fields even for the
output drivers where they are unused, and the clk_output_cfg0 and
clk_output_cfg0_mask fields for all components even though they are used
only for the output drivers.
Use a dedicated struct for the output drivers so that each block uses
exactly the fields it needs, not more.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20200723072603.1795-1-luca@lucaceresoli.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When getting the names of the child nodes, kasprintf is used to
allocate memory which is used to create the string for the node
name. Unfortunately, there is no memory check to determine
if this allocation fails, it may cause an error when trying
to get child node name.
This patch will check if the memory allocation fails, and returns
and -ENOMEM error instead of blindly moving on.
Fixes: 260249f929e8 ("clk: vc5: Enable addition output configurations of the Versaclock")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20200716122620.4538-1-aford173@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are a several places where printing an error message of
init.name occurs after init.name has been kfree'd. Also the failure
message is duplicated each time in the code. Fix this by adding
a registration error failure path for these cases, moving the
duplicated error messages to one common point and kfree'ing init.name
only after it has been used.
Changes also shrink the object code size by 171 bytes (x86-64, gcc 9.3):
Before:
text data bss dec hex filename
21057 3960 64 25081 61f9 drivers/clk/clk-versaclock5.o
After:
text data bss dec hex filename
20886 3960 64 24910 614e drivers/clk/clk-versaclock5.o
Addresses-Coverity: ("Use after free")
Fixes: f491276a5168 ("clk: vc5: Allow Versaclock driver to support multiple instances")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200625132736.88832-1-colin.king@canonical.com
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
[sboyd@kernel.org: Drop stray newline]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since the loopbacktest clock is not exported and is not touched in the
driver, it has to be added to rk3188_critical_clocks to be protected from
being disabled and in order to get the emac working.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20200722161820.5316-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The h_clk clock in the Actions Semi S500 SoC clock driver has an
invalid parent. Replace with the correct one.
Fixes: ed6b4795ece4 ("clk: actions: Add clock driver for S500 SoC")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/c57e7ebabfa970014f073b92fe95b47d3e5a70b1.1593788312.git.cristian.ciocaltea@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-qcom:
clk: qcom: gcc: Make disp gpll0 branch aon for sc7180/sdm845
ipq806x: gcc: add support for child probe
clk: qcom: msm8996: Make symbol 'cpu_msm8996_clks' static
clk: qcom: ipq8074: Add correct index for PCIe clocks
The display gpll0 branch clock inside GCC needs to always be enabled.
Otherwise the AHB clk (disp_cc_mdss_ahb_clk_src) for the display clk
controller (dispcc) will stop clocking while sourcing from gpll0 when
this branch inside GCC is turned off during unused clk disabling. We can
never turn this branch off because the AHB clk for the display subsystem
is needed to read/write any registers inside the display subsystem
including clk related ones. This makes this branch a really easy way to
turn off AHB access to the display subsystem and cause all sorts of
mayhem. Let's just make the clk ops keep the clk enabled forever and
ignore any attempts to disable this clk so that dispcc accesses keep
working.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reported-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/1594796050-14511-1-git-send-email-tdas@codeaurora.org
Fixes: 17269568f726 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180")
Fixes: 06391eddb60a ("clk: qcom: Add Global Clock controller (GCC) driver for SDM845")
[sboyd@kernel.org: Fill out commit text more]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for child probing needed for tsens driver that share the
same regs of gcc for this platform.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200716022817.30439-2-ansuelsmth@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The sparse tool complains as follows:
drivers/clk/qcom/clk-cpu-8996.c:341:19: warning:
symbol 'cpu_msm8996_clks' was not declared. Should it be static?
This variable is not used outside of clk-cpu-8996.c, so this commit
marks it static.
Fixes: 03e342dc45c9 ("clk: qcom: Add CPU clock driver for msm8996")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200714142155.35085-1-weiyongjun1@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
the eMMC clk on AST2600 SoCs that fixes the rate that is calculated by
the clk framework.
-----BEGIN PGP SIGNATURE-----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=TzDz
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux into master
Pull clk fixes from Stephen Boyd:
"A couple build fixes for issues exposed this merge window and a fix
for the eMMC clk on AST2600 SoCs that fixes the rate that is
calculated by the clk framework"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Specify IOMEM dependency for HSDK pll driver
clk: AST2600: Add mux for EMMC clock
clk: mvebu: ARMADA_AP_CPU_CLK needs to select ARMADA_AP_CP_HELPER
Currently we are not initializing the scmi clock with discrete rates
correctly. We fetch the min_rate and max_rate value only for clocks with
ranges and ignore the ones with discrete rates. This will lead to wrong
initialization of rate range when clock supports discrete rate.
Fix this by using the first and the last rate in the sorted list of the
discrete clock rates while registering the clock.
Link: https://lore.kernel.org/r/20200709081705.46084-2-sudeep.holla@arm.com
Fixes: 6d6a1d82eaef7 ("clk: add support for clocks provided by SCMI")
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reported-and-tested-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
