Instead of doing byte-at-a-time user accesses to figure
out where the fault occurred, read the saved fault_address
from the current thread structure.
For the sake of defensive programming, if the fault_address
does not fall into the user buffer range, simply assume the
whole area faulted. This will cause the fixup for
copy_from_user() to clear the entire kernel side buffer.
Signed-off-by: David S. Miller <davem@davemloft.net>
We were not calling kernel_mna_trap_fault() correctly.
Instead of being fancy, just return 0 vs. -EFAULT from
the assembler stubs, and handle that return value as
appropriate.
Create an "__retl_efault" stub for assembler exception
table entries and use it where possible.
Signed-off-by: David S. Miller <davem@davemloft.net>
The funny "range" exception table entries we had were only
used by the compat layer socketcall assembly, and it wasn't
even needed there.
For free we now get proper exception table sorting and fast
binary searching.
Signed-off-by: David S. Miller <davem@davemloft.net>
The attached patch adds extra permission grants to keys for the possessor of a
key in addition to the owner, group and other permissions bits. This makes
SUID binaries easier to support without going as far as labelling keys and key
targets using the LSM facilities.
This patch adds a second "pointer type" to key structures (struct key_ref *)
that can have the bottom bit of the address set to indicate the possession of
a key. This is propagated through searches from the keyring to the discovered
key. It has been made a separate type so that the compiler can spot attempts
to dereference a potentially incorrect pointer.
The "possession" attribute can't be attached to a key structure directly as
it's not an intrinsic property of a key.
Pointers to keys have been replaced with struct key_ref *'s wherever
possession information needs to be passed through.
This does assume that the bottom bit of the pointer will always be zero on
return from kmem_cache_alloc().
The key reference type has been made into a typedef so that at least it can be
located in the sources, even though it's basically a pointer to an undefined
type. I've also renamed the accessor functions to be more useful, and all
reference variables should now end in "_ref".
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My previous patch fixing invalidation of huge PTEs wasn't good enough, we
still had an issue if a PTE invalidation batch contained both small and
large pages. This patch fixes this by making sure the batch is flushed if
the page size fed to it changes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the ZERO_PAGE remapping complexity to the move_pte macro in
asm-generic, have it conditionally depend on
__HAVE_ARCH_MULTIPLE_ZERO_PAGE, which gets defined for MIPS.
For architectures without __HAVE_ARCH_MULTIPLE_ZERO_PAGE, move_pte becomes
a noop.
From: Hugh Dickins <hugh@veritas.com>
Fix nasty little bug we've missed in Nick's mremap move ZERO_PAGE patch.
The "pte" at that point may be a swap entry or a pte_file entry: we must
check pte_present before perhaps corrupting such an entry.
Patch below against 2.6.14-rc2-mm1, but the same bug is in 2.6.14-rc2's
mm/mremap.c, and more dangerous there since it's affecting all arches: I
think the safest course is to send Nick's patch and Yoichi's build fix and
this fix (build tested) on to Linus - so only MIPS can be affected.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also, the us3_cpufreq driver can work on Ultra-IV and IV+.
They use the SAFARI bus register to control the clock divider
just like Ultra-III and III+ do.
Signed-off-by: David S. Miller <davem@davemloft.net>
The following is generated when compiling a
recent (2.6.14-rc2-git5) kernel configured for
ARM, with GCC4.
CC init/main.o
In file included from include/linux/netdevice.h:29,
from include/net/sock.h:48,
from init/main.c:50:
include/linux/if_ether.h:114: error: array type has incomplete element type
It seems that if CONFIG_SYSCTL is not set, then
the compiler will throw an error due to the definition
of the ether_table[] array
Attached is a solution to the problem
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
Place them on separate cache lines in SMP to lower memory bouncing
between multiple CPU accessing the device.
- One part is mostly used on receive path (including
eth_type_trans()) (poll_list, poll, quota, weight, last_rx,
dev_addr, broadcast)
- One part is mostly used on queue transmit path (qdisc)
(queue_lock, qdisc, qdisc_sleeping, qdisc_list, tx_queue_len)
- One part is mostly used on xmit path (device)
(xmit_lock, xmit_lock_owner, priv, hard_start_xmit, trans_start)
'features' is placed outside of these hot points, in a location that
may be shared by all cpus (because mostly read)
name_hlist is moved close to name[IFNAMSIZ] to speedup __dev_get_by_name()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you've enabled conntrack and NAT as a module (standard case in all
distributions), and you've also enabled the new conntrack netlink
interface, loading ip_conntrack_netlink.ko will auto-load iptable_nat.ko.
This causes a huge performance penalty, since for every packet you iterate
the nat code, even if you don't want it.
This patch splits iptable_nat.ko into the NAT core (ip_nat.ko) and the
iptables frontend (iptable_nat.ko). Threfore, ip_conntrack_netlink.ko will
only pull ip_nat.ko, but not the frontend. ip_nat.ko will "only" allocate
some resources, but not affect runtime performance.
This separation is also a nice step in anticipation of new packet filters
(nf-hipac, ipset, pkttables) being able to use the NAT core.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If input message rate from userspace is too high, do not drop them,
but try to deliver using work queue allocation.
Failing there is some kind of congestion control.
It also removes warn_on on this condition, which scares people.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro pointed out that the current IB userspace verbs interface
allows userspace to cause mischief by closing file descriptors before
we're ready, or issuing the same command twice at the same time. This
patch closes those races, and fixes other obvious problems such as a
module reference leak.
Some other interface bogosities will require an ABI change to fix
properly, so I'm deferring those fixes until 2.6.15.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Added a missing TO_NATIVE call to scripts/mod/file2alias.c:do_pcmcia_entry()
- Add an alignment attribute to struct pcmcia_device_no to solve an alignment
issue seen when cross-compiling on x86 for m68k.
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Support some more TI cardbus bridges. most of them are multifunction
devices which adds 1394 controllers, smartcard readers etc. this could
also help with the various problems with the XX21 controllers seen on the
linux-pcmcia list.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Echo Audio cardbus products are known to be incompatible with EnE bridges.
in order to maybe solve the problem a EnE specific test bit has to be set,
another cleared...but other setups have a good chance to break when just
forcing the bits. so do the whole thingy automatically.
The patch adds a hook in cb_alloc() that allows special tuning for the
different chipsets. for ene just match the Echo products and set/clear the
test bits, defaults to do the same thing as w/o the patch to not break
working setups.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
At boot time, determine the D-cache, I-cache and E-cache size and
line-size. Use them in cache flushes when appropriate.
This change was motivated by discovering that the D-cache on
UltraSparc-IIIi and later are 64K not 32K, and the flushes done by the
Cheetah error handlers were assuming a 32K size.
There are still some pieces of code that are hard coding things and
will need to be fixed up at some point.
While we're here, fix the D-cache and I-cache parity error handlers
to run with interrupts disabled, and when the trap occurs at trap
level > 1 log the event via a counter displayed in /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
The trick is that we do the kernel linear mapping TLB miss starting
with an instruction sequence like this:
ba,pt %xcc, kvmap_load
xor %g2, %g4, %g5
succeeded by an instruction sequence which performs a full page table
walk starting at swapper_pg_dir.
We first take over the trap table from the firmware. Then, using this
constant PTE generation for the linear mapping area above, we build
the kernel page tables for the linear mapping.
After this is setup, we patch that branch above into a "nop", which
will cause TLB misses to fall through to the full page table walk.
With this, the page unmapping for CONFIG_DEBUG_PAGEALLOC is trivial.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Ben Dooks
The VA addresses of the Anubis CPLD registers
confoict with the addresses for the ISA space
maps used by the rest of the s3c2410 architecture
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently rpc_mkdir/rpc_rmdir and rpc_mkpipe/mk_unlink have an API that's
a little unfortunate. They take a path relative to the rpc_pipefs root and
thus need to perform a full lookup. If you look at debugfs or usbfs they
always store the dentry for directories they created and thus can pass in
a dentry + single pathname component pair into their equivalents of the
above functions.
And in fact rpc_pipefs actually stores a dentry for all but one component so
this change not only simplifies the core rpc_pipe code but also the callers.
Unfortuntately this code path is only used by the NFS4 idmapper and
AUTH_GSSAPI for which I don't have a test enviroment. Could someone give
it a spin? It's the last bit needed before we can rework the
lookup_hash API
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In fact, ->set_buffer_size should be completely functionless for non-UDP.
Test-plan:
Check socket buffer size on UDP sockets over time.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Each transport implementation can now set unique bind, connect,
reestablishment, and idle timeout values. These are variables,
allowing the values to be modified dynamically. This permits
exponential backoff of any of these values, for instance.
As an example, we implement exponential backoff for the connection
reestablishment timeout.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Select an RPC client source port between 650 and 1023 instead of between
1 and 800. The old range conflicts with a number of network services.
Provide sysctls to allow admins to select a different port range.
Note that this doesn't affect user-level RPC library behavior, which
still uses 1 to 800.
Based on a suggestion by Olaf Kirch <okir@suse.de>.
Test-plan:
Repeated mount and unmount. Destructive testing. Idle timeouts.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: Move some macros that are specific to the Van Jacobson
implementation into xprt.c. Get rid of the cong_wait field in
rpc_xprt, which is no longer used. Get rid of xprt_clear_backlog.
Test-plan:
Compile with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Get rid of the "xprt->nocong" variable.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss with UDP mounts.
Look for significant regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The final place where congestion control state is adjusted is in
xprt_release, where each request is finally released. Add a callout
there to allow transports to perform additional processing when a
request is about to be released.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for significant
regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
A new interface that allows transports to adjust their congestion window
using the Van Jacobson implementation in xprt.c is provided.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for
significant regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allow transports to hook the retransmit timer interrupt. Some transports
calculate their congestion window here so that a retransmit timeout has
immediate effect on the congestion window.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for significant
regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The next method we abstract is the one that releases a transport,
allowing another task to have access to the transport.
Again, one generic version of this is provided for transports that
don't need the RPC client to perform congestion control, and one
version is for transports that can use the original Van Jacobson
implementation in xprt.c.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for
significant regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The next several patches introduce an API that allows transports to
choose whether the RPC client provides congestion control or whether
the transport itself provides it.
The first method we abstract is the one that serializes access to the
RPC transport to prevent the bytes from different requests from mingling
together. This method provides proper request serialization and the
opportunity to prevent new requests from being started because the
transport is congested.
The normal situation is for the transport to handle congestion control
itself. Although NFS over UDP was first, it has been recognized after
years of experience that having the transport provide congestion control
is much better than doing it in the RPC client. Thus TCP, and probably
every future transport implementation, will use the default method,
xprt_lock_write, provided in xprt.c, which does not provide any kind
of congestion control. UDP can continue using the xprt.c-provided
Van Jacobson congestion avoidance implementation.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for significant
regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Prepare the way to remove the "xprt->nocong" variable by adding a callout
to the RPC client transport switch API to handle setting RPC retransmit
timeouts.
Add a pair of generic helper functions that provide the ability to set a
simple fixed timeout, or to set a timeout based on the state of a round-
trip estimator.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for significant
regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Now we can fix up the last few places that use the "xprt->stream"
variable, and get rid of it from the rpc_xprt structure.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add a generic mechanism for skipping over transport-specific headers
when constructing an RPC request. This removes another "xprt->stream"
dependency.
Test-plan:
Write-intensive workload on a single mount point (try both UDP and
TCP).
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
