Wake gpiochip_generic_request() call into the pinctrl helpers only if a
GPIO controller had any pin-ranges assigned to it. This allows a driver
to unconditionally use this helper if it supports multiple devices of
which only a subset have pin-ranges assigned to them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-2-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The default handling of the gpio-line-names property by the
gpiolib-of implementation does not work with the multiple
gpiochip banks per device structure used by the gpio-brcmstb
driver.
This commit adds driver level support for the device tree
property so that GPIO lines can be assigned friendly names.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Link: https://lore.kernel.org/r/1583780521-45702-1-git-send-email-opendmb@gmail.com
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since name == NULL can't ever match, move the check out of
IRQ-disabled region.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
DSET/DCLR registers only works on output pins. Add corresponding
BGPIOF_NO_SET_ON_INPUT flag to bgpio_init call to fix direction_out
behavior.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Some gpio controllers ignores pin value writing when that pin is
configured as input mode. As a result, bgpio_dir_out should set
pin to output before configuring pin values or gpio pin values
can't be set up properly.
Introduce two variants of bgpio_dir_out: bgpio_dir_out_val_first
and bgpio_dir_out_dir_first, and assign direction_output according
to a new flag: BGPIOF_NO_SET_ON_INPUT.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
platform_get_irq() will generate an error message if the requested irq
is not present
mvebu-gpio f1010140.gpio: IRQ index 3 not found
use platform_get_irq_optional() to avoid the error message being
generated.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Existing (irq < 0) condition is always false because adev->irq has unsigned
type and contains 0 in case of failed irq_of_parse_and_map(). Up to now all
the mapping errors were silently ignored.
Seems that repairing this check would be backwards-incompatible and might
break the probe() for the implementations without IRQ support. Therefore
warn the user instead.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
These two devres functions devm_gpiochip_[add|remove]()
were in the wrong file. They should be in gpiolib-devres.c
not gpiolib.c.
Link: https://lore.kernel.org/r/20200313081522.35143-1-linus.walleij@linaro.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit a522f1d0c3.
With cpu_pm handling fixed for omaps, and with gpio-omap now returning
notify error on pending interrupts, we can drop the old workaround for
seeing if there may be pending edge interrupts.
Depends-on: ARM: OMAP2+: Handle errors for cpu_pm
Depends-on: gpio: omap: Block idle on pending gpio interrupts
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200304225433.37336-4-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the SoC cpuidle handling fixed for cpu_pm, we can now start to
return NOTIFY_BAD if there there are pending gpio interrupts.
This way the deeper SoC idle states can get blocked, and gpio latency
is improved in some cases. Note that this will not help with the
latency if the SoC has already entered a deeper idle state.
Note that this patch depends on cpu_pm properly handling the errors
returned by notifiers. For omap variants, this is fixed with patch
"ARM: OMAP2+: Handle errors for cpu_pm".
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200304225433.37336-3-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- replace z zero-length array with flexible-array member in gpio-uniphier
- make naming of variables consistent in uapi line event code
- fix the behavior of line watch/unwatch ioctl()
-----BEGIN PGP SIGNATURE-----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=ASHn
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.7-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.7 part 2
- replace z zero-length array with flexible-array member in gpio-uniphier
- make naming of variables consistent in uapi line event code
- fix the behavior of line watch/unwatch ioctl()
The optimization to check for requested lines actually optimized for the
uncomon error case, where one of the GPIO lines is still in use.
Hence the error message must be printed when the loop is terminated
early, not when it went through all available GPIO lines.
Fixes: 869233f813 ("gpiolib: Optimize gpiochip_remove() when check for requested line")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200302082448.11795-1-geert+renesas@glider.be
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When operating on the bits of watched_lines bitmap, we're using
desc_to_gpio() which returns the GPIO number from the global numberspace.
This leads to all sorts of memory corruptions and invalid behavior. We
should switch to using gpio_chip_hwgpio() instead.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Reported-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Kent Gibson <warthog618@gmail.com>
Fix the field having a bit cleared by the unwatch ioctl().
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename 'event' to 'ge' to be consistent with other use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Here are the following optimizations have been done:
- break the loop after first found requested line
- due to above, drop redundant boolean variable
- replace open coded variant of gpiochip_is_requested()
- due to above, drop redundant pointer to struct gpio_desc
- use 'unsigned int' instead of 'unsigned' for loop counter
Note, pointer to struct gpio_chip followed by pointer to struct gpio_device
is still valid, back link is not.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200225114725.839-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As GPIO hogs are configured at GPIO controller initialization time,
adding/removing GPIO hogs in DT overlays does not work.
Add support for GPIO hogs described in DT overlays by registering an OF
reconfiguration notifier, to handle the addition and removal of GPIO hog
subnodes to/from a GPIO controller device node.
Note that when a GPIO hog device node is being removed, its "gpios"
properties is no longer available, so we have to keep track of which
node a hog belongs to, which is done by adding a pointer to the hog's
device node to struct gpio_desc.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200220130149.26283-3-geert+renesas@glider.be
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Extract the code to add all GPIO hogs of a gpio-hog node into its own
function, so it can be reused.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200220130149.26283-2-geert+renesas@glider.be
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The existing use of ktime_get_real_ns() in the timestamps from
the GPIO events is dubious.
We have had several discussions about this timestamp, and it is
unclear whether userspace has ever taken into account that a
timestamp from ktime_get_real_ns() can actually move backwards
in time relative the previous timetamp, and userspace is more
likely to expect a monotonic counter.
Background:
https://lore.kernel.org/linux-gpio/CAK8P3a1Skvm48sje8FNDPLYqyz9Lf8q0qX1QETWtyZTxuX4k1g@mail.gmail.com/https://marc.info/?l=linux-gpio&m=151661955709074&w=2
The change is ABI incompatible, but incompatible in a way that
is IMO more likely to fix future bugs rather than break current
userspace. To the best of my knowledge all userspace expects
a monotonic timestamp and users are just lucky that they very
seldom move backwards in time.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whenever retrieving a descriptor from a gpiochip: use the provided
helper which checks for errors.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200219094702.6463-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All the irq related callbacks are called with the (raw) spinlock
desc->lock being held. So the lock here must be raw as well. Also irqs
were already disabled by the caller for the irq chip callbacks, so the
non-irq variants of spin_lock must be used there.
Fixes: be8c8facc7 ("gpio: new driver to work with a 8x12 siox")
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20200211135121.15752-1-uwe@kleine-koenig.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The indentation is wrong in gpio_mockup_apply_pull(). This patch makes
the code more readable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200210155059.29609-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently there is no way for user-space to be informed about changes
in status of GPIO lines e.g. when someone else requests the line or its
config changes. We can only periodically re-read the line-info. This
is fine for simple one-off user-space tools, but any daemon that provides
a centralized access to GPIO chips would benefit hugely from an event
driven line info synchronization.
This patch adds a new ioctl() that allows user-space processes to reuse
the file descriptor associated with the character device for watching
any changes in line properties. Every such event contains the updated
line information.
Currently the events are generated on three types of status changes: when
a line is requested, when it's released and when its config is changed.
The first two are self-explanatory. For the third one: this will only
happen when another user-space process calls the new SET_CONFIG ioctl()
as any changes that can happen from within the kernel (i.e.
set_transitory() or set_debounce()) are of no interest to user-space.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
We'll soon be filling out the gpioline_info structure in multiple
places. Add a separate function that given a gpio_desc sets all relevant
fields.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Currently if the line-event kfifo is full, we just silently drop any new
events. Add a ratelimited debug message so that we at least have some
trace in the kernel log of event overflow.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The read_lock mutex is supposed to prevent collisions between reading
and writing to the line event kfifo but it's actually only taken when
the events are being read from it.
Drop the mutex entirely and reuse the spinlock made available to us in
the waitqueue struct. Take the lock whenever the fifo is modified or
inspected. Drop the call to kfifo_to_user() and instead first extract
the new element from kfifo when the lock is taken and only then pass
it on to the user after the spinlock is released.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The check with register value and mask should be & rather than &&.
While at it, also use "unsigned int" for value variable because
regmap_read() takes unsigned int *val argument.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The .set callback should just set output value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Not all platforms use those. Let's use
platform_get_irq_byname_optional() instead platform_get_irq_byname() so
that we avoid a useless warning:
[ 1.359455] pxa-gpio d4019000.gpio: IRQ gpio0 not found
[ 1.359583] pxa-gpio d4019000.gpio: IRQ gpio1 not found
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
- New Device Support
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
- New Functionality
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
- Fix-ups
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers; madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
- Bug Fixes
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon
-----BEGIN PGP SIGNATURE-----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=t4+B
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we
got rid of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips
along with the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much
improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt
map is provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML
DT bindings schema. (A first user of this.)
-----BEGIN PGP SIGNATURE-----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=PnK5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
Core changes:
- Document the usecases for the kernelspace vs userspace
handling of GPIOs.
- Handle MSI (message signalled interrupts) properly in the
core hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor
array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain
with GPIOLIB_IRQCHIP on top of the revert of the previous
buggy switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes.
-----BEGIN PGP SIGNATURE-----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=3Glg
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.6 kernel cycle.
This is a pretty calm cycle so far, nothing special going on really.
Some more changes will come in from the irqchip and pin control trees.
I also deleted an orphan include file for FMC that was dangling since
subsystem was removed.
Core changes:
- Document the usecases for the kernelspace vs userspace handling of
GPIOs.
- Handle MSI (message signalled interrupts) properly in the core
hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain with
GPIOLIB_IRQCHIP on top of the revert of the previous buggy
switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes"
* tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (48 commits)
MAINTAINERS: Replace Tien Hock Loh as Altera PIO maintainer
gpiolib: hold gpio devices lock until ->descs array is initialised
gpio: aspeed-sgpio: fixed typos
gpio: mvebu: clear irq in edge cause register before unmask edge irq
gpiolib: Lower verbosity when allocating hierarchy irq
gpiolib: Remove duplicated function gpio_do_set_config()
gpio: Fix the no return statement warning
gpio: wcd934x: Add support to wcd934x gpio controller
gpiolib: remove set but not used variable 'config'
gpio: vx855: fixed a typo
gpio: mockup: sort headers alphabetically
gpio: mockup: update the license tag
gpio: Remove the unused flags
gpiolib: Set lockdep class for hierarchical irq domains
gpio: thunderx: Switch to GPIOLIB_IRQCHIP
gpiolib: Add the support for the msi parent domain
gpiolib: Add support for the irqdomain which doesn't use irq_fwspec as arg
gpio: Add use guidance documentation
dt-bindings: gpio: wcd934x: Add bindings for gpio
gpio: altera: change to platform_get_irq_optional to avoid false-positive error
...
- A mechanism to shield isolated tasks from managed interrupts:
The affinity of managed interrupts is completely controlled by the
kernel and user space has no influence on them. The reason is that
the automatically assigned affinity correlates to the multi-queue
CPU handling of block devices.
If the generated affinity mask spaws both housekeeping and isolated CPUs
the interrupt could be routed to an isolated CPU which would then be
disturbed by I/O submitted by a housekeeping CPU.
The new mechamism ensures that as long as one housekeeping CPU is online
in the assigned affinity mask the interrupt is routed to a housekeeping
CPU.
If there is no online housekeeping CPU in the affinity mask, then the
interrupt is routed to an isolated CPU to keep the device queue intact,
but unless the isolated CPU submits I/O by itself these interrupts are
not raised.
- A small addon to the device tree irqdomain core code to avoid
duplication in irq chip drivers
- Conversion of the SiFive PLIC to hierarchical domains
- The usual pile of new irq chip drivers: SiFive GPIO, Aspeed SCI, NXP
INTMUX, Meson A1 GPIO
- The first cut of support for the new ARM GICv4.1
- The usual pile of fixes and improvements in core and driver code
-----BEGIN PGP SIGNATURE-----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=E2VR
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The interrupt departement provides:
- A mechanism to shield isolated tasks from managed interrupts:
The affinity of managed interrupts is completely controlled by the
kernel and user space has no influence on them. The reason is that
the automatically assigned affinity correlates to the multi-queue
CPU handling of block devices.
If the generated affinity mask spaws both housekeeping and isolated
CPUs the interrupt could be routed to an isolated CPU which would
then be disturbed by I/O submitted by a housekeeping CPU.
The new mechamism ensures that as long as one housekeeping CPU is
online in the assigned affinity mask the interrupt is routed to a
housekeeping CPU.
If there is no online housekeeping CPU in the affinity mask, then
the interrupt is routed to an isolated CPU to keep the device queue
intact, but unless the isolated CPU submits I/O by itself these
interrupts are not raised.
- A small addon to the device tree irqdomain core code to avoid
duplication in irq chip drivers
- Conversion of the SiFive PLIC to hierarchical domains
- The usual pile of new irq chip drivers: SiFive GPIO, Aspeed SCI,
NXP INTMUX, Meson A1 GPIO
- The first cut of support for the new ARM GICv4.1
- The usual pile of fixes and improvements in core and driver code"
* tag 'irq-core-2020-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
genirq, sched/isolation: Isolate from handling managed interrupts
irqchip/gic-v4.1: Allow direct invalidation of VLPIs
irqchip/gic-v4.1: Suppress per-VLPI doorbell
irqchip/gic-v4.1: Add VPE INVALL callback
irqchip/gic-v4.1: Add VPE eviction callback
irqchip/gic-v4.1: Add VPE residency callback
irqchip/gic-v4.1: Add mask/unmask doorbell callbacks
irqchip/gic-v4.1: Plumb skeletal VPE irqchip
irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP
irqchip/gic-v4.1: Don't use the VPE proxy if RVPEID is set
irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP
irqchip/gic-v4.1: VPE table (aka GICR_VPROPBASER) allocation
irqchip/gic-v3: Add GICv4.1 VPEID size discovery
irqchip/gic-v3: Detect GICv4.1 supporting RVPEID
irqchip/gic-v3-its: Fix get_vlpi_map() breakage with doorbells
irqdomain: Fix a memory leak in irq_domain_push_irq()
irqchip: Add NXP INTMUX interrupt multiplexer support
dt-bindings: interrupt-controller: Add binding for NXP INTMUX interrupt multiplexer
irqchip: Define EXYNOS_IRQ_COMBINER
irqchip/meson-gpio: Add support for meson a1 SoCs
...
- Convert to reasonable timeouts for all CMD6 commands (updates for BKOPS,
CACHE_FLUSH and INAND_CMD38_ARG_EXT_CSD) for eMMC
- Respect f_max clock rate at card initialization
- Add gpiod_toggle_active_low() API
- Consolidate slot-gpio code by using gpiod_toggle_active_low()
MMC host:
- Add pinctrl_select_default_state() API
- Consolidate pintctrl code by using pinctrl_select_default_state()
- mmci: Support any block sizes for SDIO for some variants
- mmci: Enable reset control for stm32_sdmmc
- mmc_spi: Toggle SPI_CS_HIGH polarity rather than hard-coding it
- renesas_sdhi: Add support for the r8a77961 variant
- renesas_sdhi: A few minor improvements
- rockchip-dw-mshc: Add support for the rk3308 variant
- sdhci: Enable support for external DMA controllers
- sdhci: Fixup error path when sending CMD12
- sdhci-brcmstb: Add support for 7216b0 variant
- sdhci-brcmstb: Add support for command queuing (CQHCI)
- sdhci-brcmstb: Add support for eMMC HS400ES mode
- sdhci-msm: Add support for the sc7180 variant
- sdhci-msm: Add support for command queuing (CQHCI)
- sdhci-of-at91: Add support for the SAM9x60 variant
- sdhci-of-at91: Improve support for tunings
- sdhci-of-esdhc: A few fixups for some clock related issues
- sdhci-omap: Add support for the am335x and the am437x variants
- sdhci-omap: Improve support for erase operations
- sdhci-omap: Add support for external DMA
-----BEGIN PGP SIGNATURE-----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=L0cJ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"There are no updates for the MEMSTICK subsystem this time. But note
that I am also carrying a patch from the pinctrl tree, which has been
shared through an immutable branch.
Summary:
MMC core:
- Convert to reasonable timeouts for all CMD6 commands (updates for
BKOPS, CACHE_FLUSH and INAND_CMD38_ARG_EXT_CSD) for eMMC
- Respect f_max clock rate at card initialization
- Add gpiod_toggle_active_low() API
- Consolidate slot-gpio code by using gpiod_toggle_active_low()
MMC host:
- Add pinctrl_select_default_state() API
- Consolidate pintctrl code by using pinctrl_select_default_state()
- mmci: Support any block sizes for SDIO for some variants
- mmci: Enable reset control for stm32_sdmmc
- mmc_spi: Toggle SPI_CS_HIGH polarity rather than hard-coding it
- renesas_sdhi: Add support for the r8a77961 variant
- renesas_sdhi: A few minor improvements
- rockchip-dw-mshc: Add support for the rk3308 variant
- sdhci: Enable support for external DMA controllers
- sdhci: Fixup error path when sending CMD12
- sdhci-brcmstb: Add support for 7216b0 variant
- sdhci-brcmstb: Add support for command queuing (CQHCI)
- sdhci-brcmstb: Add support for eMMC HS400ES mode
- sdhci-msm: Add support for the sc7180 variant
- sdhci-msm: Add support for command queuing (CQHCI)
- sdhci-of-at91: Add support for the SAM9x60 variant
- sdhci-of-at91: Improve support for tunings
- sdhci-of-esdhc: A few fixups for some clock related issues
- sdhci-omap: Add support for the am335x and the am437x variants
- sdhci-omap: Improve support for erase operations
- sdhci-omap: Add support for external DMA"
* tag 'mmc-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (89 commits)
mmc: core: Default to generic_cmd6_time as timeout in __mmc_switch()
mmc: block: Use generic_cmd6_time when modifying INAND_CMD38_ARG_EXT_CSD
mmc: core: Specify timeouts for BKOPS and CACHE_FLUSH for eMMC
mmc: sdhci-cadence: remove unneeded 'inline' marker
dt-bindings: mmc: rockchip-dw-mshc: add description for rk3308
dt-bindings: mmc: convert rockchip dw-mshc bindings to yaml
dt-bindings: mmc: convert synopsys dw-mshc bindings to yaml
mmc: sdhci-msm: Add CQHCI support for sdhci-msm
mmc: sdhci: Let a vendor driver supply and update ADMA descriptor size
mmc: sdhci-of-esdhc: fix serious issue clock is always disabled
mmc: sdhci-of-esdhc: fix transfer mode register reading
mmc: sdhci-brcmstb: Fix incorrect switch to HS mode
mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)
mmc: sdhci-brcmstb: Add shutdown callback
mmc: sdhci-brcmstb: Fix driver to defer on clk_get defer
mmc: sdhci-brcmstb: Add ability to use HS400ES transfer mode
dt-bindings: mmc: brcm,sdhci-brcmstb: Add support for 7216b0
mmc: core: limit probe clock frequency to configured f_max
mmc: sdhci-milbeaut: Remove redundant platform_get_irq error message
mmc: sdhci: fix an issue of mixing different types
...
- use platform_get_irq_optional() in gpio-altera
-----BEGIN PGP SIGNATURE-----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=iqpY
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.6-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.6
- use platform_get_irq_optional() in gpio-altera
ROHM BD71828 PMIC contains 4 pins which can be configured by OTP
to be used for general purposes. First 3 can be used as outputs
and 4.th pin can be used as input. Allow them to be controlled
via GPIO framework.
The driver assumes all of the pins are configured as GPIOs and
trusts that the reserved pins in other OTP configurations are
excluded from control using "gpio-reserved-ranges" device tree
property (or left untouched by GPIO users).
Typical use for 4.th pin (input) is to use it as HALL sensor
input so that this pin state is toggled when HALL sensor detects
LID position change (from close to open or open to close). PMIC
HW implements some extra logic which allows PMIC to power-up the
system when this pin is toggled. Please see the data sheet for
details of GPIO options which can be selected by OTP settings.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If a driver consuming the GPIO chip is being probed at the same time as
the GPIO driver is registering the chip, it is possible for the
consuming driver to see the ->descs array in an uninitialised state.
For example, the gpio-keys-polled driver can fail like this:
kernel: gpiod_request: invalid GPIO (no device)
kernel: gpio-keys-polled PRP0001:07: failed to get gpio: -22
kernel: gpio-keys-polled: probe of PRP0001:07 failed with error -22
This patch makes gpiochip_add() hold the lock protecting gpio_devices
until it has finished setting desc->gdev on the newly inserted list
entry.
Signed-off-by: Dan Callaghan <dan.callaghan@opengear.com>
Link: https://lore.kernel.org/r/20200121001216.15964-1-dan.callaghan@opengear.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_set_chained_irqchip() would assign a chained handler
to a GPIO chip. We now populate struct gpio_irq_chip for all
chained GPIO irqchips so drop this function.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200113220800.77817-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When input GPIO set from 0 to 1, the interrupt bit asserted in the GPIO
Interrupt Cause Register (ICR) even if the corresponding interrupt
masked in the GPIO Interrupt Mask Register.
Because interrupt mask register only affects assertion of the interrupt
bits in Main Interrupt Cause Register and it does not affect the
setting of bits in the GPIO ICR.
So, there is problem, when we unmask interrupt with already
asserted bit in the GPIO ICR, then false interrupt immediately occurs
even if GPIO don't change their value since last unmask.
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20200115073811.24438-1-bigunclemax@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the current codes, the following 3 lines would be output to
the console for each irq line.
gpio gpiochip0: (gpio_thunderx): allocate IRQ 10, hwirq 0
gpio gpiochip0: (gpio_thunderx): found parent hwirq 245784
gpio gpiochip0: (gpio_thunderx): alloc_irqs_parent for 10 parent hwirq 245784
In general, there are about tens of irq lines for each gpio chip,
and then it would emit so many insignificant log in the boot process.
These infos are more suitable for the dbg purpose. So change these
to the dbg level. With this change, about 200 lines are suppressed
on my Marvell cn96xx board.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200120095625.25164-1-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Tiger Lake appears to have _HID enumeration, thus driver has been updated
* Coffee Lake-S has the same IP as Sunrisepoint, thus ID has been added
* Baytrail has got more clean ups and bug fixes, such as direct IRQ handling
* Lynxpoint GPIO has been converted to true pin control driver
* The common driver now uses IRQ chip enumeration via GPIO chip
The following is an automated git shortlog grouped by driver:
baytrail:
- Replace WARN with dev_info_once when setting direct-irq pin to output
- Do not clear IRQ flags on direct-irq enabled pins
- Reuse struct intel_pinctrl in the driver
- Use local variable to keep device pointer
- Keep pointer to struct device instead of its container
- Use GPIO direction definitions
- Move IRQ valid mask initialization to a dedicated callback
- Group GPIO IRQ chip initialization
- Allocate IRQ chip dynamic
cherryview:
- Use GPIO direction definitions
intel:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Share struct intel_pinctrl for wider use
- Use GPIO direction definitions
lynxpoint:
- Update summary in the driver
- Switch to pin control API
- Add GPIO <-> pin mapping ranges via callback
- Implement ->pin_dbg_show()
- Add pin control operations
- Reuse struct intel_pinctrl in the driver
- Add pin control data structures
- Implement intel_gpio_get_direction callback
- Implement ->irq_ack() callback
- Move ownership check to IRQ chip
- Move lp_irq_type() closer to IRQ related routines
- Move ->remove closer to ->probe()
- Extract lp_gpio_acpi_use() for future use
- Convert unsigned to unsigned int
- Switch to memory mapped IO accessors
- Keep pointer to struct device instead of its container
- Relax GPIO request rules
- Assume 2 bits for mode selector
- Use standard pattern for memory allocation
- Use %pR to print IO resource
- Drop useless assignment
- Correct amount of pins
- Use raw_spinlock for locking
- Move GPIO driver to pin controller folder
sunrisepoint:
- Add Coffee Lake-S ACPI ID
- Add missing Interrupt Status register offset
tigerlake:
- Tiger Lake uses _HID enumeration
-----BEGIN PGP SIGNATURE-----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=+ZAJ
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.6-1
* Tiger Lake appears to have _HID enumeration, thus driver has been updated
* Coffee Lake-S has the same IP as Sunrisepoint, thus ID has been added
* Baytrail has got more clean ups and bug fixes, such as direct IRQ handling
* Lynxpoint GPIO has been converted to true pin control driver
* The common driver now uses IRQ chip enumeration via GPIO chip
The following is an automated git shortlog grouped by driver:
baytrail:
- Replace WARN with dev_info_once when setting direct-irq pin to output
- Do not clear IRQ flags on direct-irq enabled pins
- Reuse struct intel_pinctrl in the driver
- Use local variable to keep device pointer
- Keep pointer to struct device instead of its container
- Use GPIO direction definitions
- Move IRQ valid mask initialization to a dedicated callback
- Group GPIO IRQ chip initialization
- Allocate IRQ chip dynamic
cherryview:
- Use GPIO direction definitions
intel:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Share struct intel_pinctrl for wider use
- Use GPIO direction definitions
lynxpoint:
- Update summary in the driver
- Switch to pin control API
- Add GPIO <-> pin mapping ranges via callback
- Implement ->pin_dbg_show()
- Add pin control operations
- Reuse struct intel_pinctrl in the driver
- Add pin control data structures
- Implement intel_gpio_get_direction callback
- Implement ->irq_ack() callback
- Move ownership check to IRQ chip
- Move lp_irq_type() closer to IRQ related routines
- Move ->remove closer to ->probe()
- Extract lp_gpio_acpi_use() for future use
- Convert unsigned to unsigned int
- Switch to memory mapped IO accessors
- Keep pointer to struct device instead of its container
- Relax GPIO request rules
- Assume 2 bits for mode selector
- Use standard pattern for memory allocation
- Use %pR to print IO resource
- Drop useless assignment
- Correct amount of pins
- Use raw_spinlock for locking
- Move GPIO driver to pin controller folder
sunrisepoint:
- Add Coffee Lake-S ACPI ID
- Add missing Interrupt Status register offset
tigerlake:
- Tiger Lake uses _HID enumeration
