This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should mitigate the system
hangs observed after the introduction of cpufreq for the A33.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In common PLL designs, changes to the dividers take effect almost
immediately, while changes to the multipliers (implemented as
dividers in the feedback loop) take a few cycles to work into
the feedback loop for the PLL to stablize.
Sometimes when the PLL clock rate is changed, the decrease in the
divider is too much for the decrease in the multiplier to catch up.
The PLL clock rate will spike, and in some cases, might lock up
completely. This is especially the case if the divider changed is
the pre-divider, which affects the reference frequency.
This patch introduces a clk notifier callback that will gate and
then ungate a clk after a rate change, effectively resetting it,
so it continues to work, despite any possible lockups. Care must
be taken to reparent any consumers to other temporary clocks during
the rate change, and that this notifier callback must be the first
to be registered.
This is intended to fix occasional lockups with cpufreq on newer
Allwinner SoCs, such as the A33 and the H3. Previously it was
thought that reparenting the cpu clock away from the PLL while
it stabilized was enough, as this worked quite well on the A31.
On the A33, hangs have been observed after cpufreq was recently
introduced. With the H3, a more thorough test [1] showed that
reparenting alone isn't enough. The system still locks up unless
the dividers are limited to 1.
A hunch was if the PLL was stuck in some unknown state, perhaps
gating then ungating it would bring it back to normal. Tests
done by Icenowy Zheng using Ondrej's test firmware shows this
to be a valid solution.
[1] http://www.spinics.net/lists/arm-kernel/msg552501.html
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ccu-sun9i-a80 driver uses the ccu_mult_ops struct, but unlike the other
users it doesen't select the corresponding Kconfig symbol under which the
struct is compiled in.
This results in the following link error with CONFIG_SUN9I_A80_CCU=y and
CONFIG_SUNXI_CCU_MULT=n:
drivers/built-in.o:(.data+0x2d638): undefined reference to 'ccu_mult_ops'
Fix this by explicitly selecting CONFIG_SUNXI_CCU_MULT like the other
users of the struct.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With CONFIG_RESET_CONTROLLER=n we get the following link error in the
sunxi-ng clk driver:
drivers/built-in.o: In function `sunxi_ccu_probe':
mux-core.c:(.text+0x12fe68): undefined reference to 'reset_controller_register'
mux-core.c:(.text+0x12fe68): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'reset_controller_register'
Fix this by adding the appropriate select statement.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CLK_NUMBER value of PRCM CCU is wrongly set to (CLK_APB0_PWD + 1),
which prevented the IR mod clock from being set up.
Change it to (CLK_IR + 1) in order to correctly get IR mod set up.
Fixes: cdb8b80b6093 ("clk: sunxi-ng: add support for PRCM CCUs")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The first parent of ir clk in PRCM CCU is wrongly written as "osc32K"
instead of "osc32k".
Change it to "osc32k".
Fixes: cdb8b80b6093 ("clk: sunxi-ng: add support for PRCM CCUs")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add clock index to clock registration failure message. Clock name
is sometimes not available, when things go really wrong.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DDR1 PLL on the A33 is an oddball amongst the A33 CCU clocks.
It is a clock multiplier, with the effective multiplier in the
range of 12 ~ 255 and no offset between the multiplier value and
the value programmed into the register.
Implement the zero offset and minimum value of 12 for this clock.
Fixes: d05c748bd730 ("clk: sunxi-ng: Add A33 CCU support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPU cluster PLLs on the A80 are NP clocks that are atypical in two ways:
- The P factor is 1 bit wide, and translates to a /1 or /4 divider.
- The P factor should only be used for output frequencies lower than
288 MHz. The N factor has a lower limit of 12, which likely contributed
to this extra divider.
According to the user manual, the clocks can only go as low as 200 MHz.
The vendor BSP kernel does not even define operating points below 360
MHz for these clocks. The lower end for cpufreq in the vendor kernel is
even higher. The mainline Linux kernel doesn't support cpufreq for the
A80 at the moment. This means the lower frequencies are untested, and
will likely remain unused.
The new sunxi-ng style clocks don't support the quirks listed above.
Instead of trying to work the quirks in for something of little usage,
we re-model the clocks into N-type multipler clocks, with P fixed at 1.
At probe time we check if P is set to 4, and fix it up if needed. This
is highly unlikely though.
Fixes: b8eb71dcdd08 ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some PLL clocks are N (multiplier) type clocks, or can be simplified
as such. An example of the former is the DDR1 PLL clock on the A33.
An example of the latter is the CPU PLL clock on the A80, in which
the P divider is only used for low frequencies that are of little
use. Both clocks support PLL lock detection.
The mult clock macro implies support for this, but that is not true.
The field is simply discarded. This patch adds proper support for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SoCs after A31 has a clock controller module in the PRCM part.
Support the clock controller module on H3/5 and A64 now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In commit e66f81bbd746 ("clk: sunxi-ng: Implement factors offsets"), the
final formula of NKMP clocks' recalc_rate is refactored; however, the
refactored formula broke the calculation due to some C language operand
priority problem -- the priority of operand >> is lower than * and /,
makes the formula being parsed as "(parent_rate * n * k) >> (p / m)", but
it should be "(parent_rate * n * k >> p) / m".
Add the pair of parentheses to fix up this issue. This pair of
parentheses used to exist in the old formula.
Fixes: e66f81bbd746 ("clk: sunxi-ng: Implement factors offsets")
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The mult/div for osc12M was previously backwards (giving a 48M rate
for osc12M). Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tighten the depends on the various AllWinn SoCs so we don't
inadvertantly get clock drivers when we're not wanting them
like 32 bit SoC clocks for 64 bit configs. Ensure there's
still test coverage though.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H5 is a SoC that features a design which keeps the peripheral
compatible with H3, so that it have also a CCU like the one on H3 --
only one bus gate/reset is added, and the mmc sample/output phases are
removed because of MMC controller update.
Add its support in our existing H3 CCU driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clock gates have a pre-divider between the source input and the
gate itself. A notable example is the HSIC 12 MHz clock found on the
A83T, which has the 24 MHz main oscillator as its input, and a /2
pre-divider.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The enable bit offset for the hdmi-ddc module clock is wrong. It is
pointing to the main hdmi module clock enable bit.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8fa6 ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A randconfig build ran into this rare link error:
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.1+0x4): undefined reference to `ccu_nkmp_ops'
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.7+0x4): undefined reference to `ccu_nkmp_ops'
This adds the missing 'select'.
Fixes: 5e73761786d6 ("clk: sunxi-ng: Add sun5i CCU driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MP style clocks support an mux with pre-dividers. While the driver
correctly accounted for them in the .determine_rate callback, it did
not in the .recalc_rate and .set_rate callbacks.
This means when calculating the factors in the .set_rate callback, they
would be off by a factor of the active pre-divider. Same goes for
reading back the clock rate after it is set.
Cc: stable@vger.kernel.org
Fixes: 2ab836db5097 ("clk: sunxi-ng: Add M-P factor clock support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Fixes: 783ab76ae553 ("clk: sunxi-ng: Add A80 Display Engine CCU")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We get a link error when CCU_MULT is not set with the
newly added driver:
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.17+0x4): undefined reference to `ccu_mult_ops'
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.5+0x4): undefined reference to `ccu_mult_ops'
Fixes: 5e73761786d6 ("clk: sunxi-ng: Add sun5i CCU driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This kzalloc() could fail. Let's bail out with -ENOMEM here
instead of NULL dereferencing. That silences static checkers. We
should also cleanup on the error path even though this function
returning an error probably means the system won't boot.
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
With the A80 SoC, Allwinner grouped and moved some subsystem specific
clock controls to a separate address space, and possibly separate
hardware block.
One such subsystem is the display engine. The main clock control unit
now only has 1 set of bus gate, dram gate, module clock, and reset
control for the entire display subsystem. These feed into a secondary
clock control unit, which has controls for each individual module
of the display pipeline. This block is not documented in the user
manual. Allwinner's kernel was used as the reference.
Add support for the display engine clock controls found on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the USB clock controls found on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the main clock unit found in the A80. Some clocks were
not documented in the released user manual, but were found in the
official kernel from Allwinner. These include controls for the I2S,
SPDIF, SATA, and eDP blocks.
Note that on the A80, some subsystems have separate clock controllers
downstream of the main clock unit. These include the MMC, USB, and
display engine subsystems.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Allwinner A80 SoC, the PLL lock status indicators are grouped
together in a separate register, as opposed to being scattered in each
PLL's configuration register.
Add a flag to support this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If the CLK_SET_RATE_PARENT flag is set, we want to try getting the
closest parent rate.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds support for the CLK_SET_RATE_NO_REPARENT flag to the
mux determine_rate helper, based on examples from clk-composite and
clk-mux.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The determine_rate helper used ccu_mux_helper_adjust_parent_for_prediv()
to adjust the parent_rate to account for pre-dividers, but then passed
the pristine parent clock rate from clk_hw_get_rate() to the round()
callback, thereby ignoring the pre-divider adjustment. In addition,
it was saving the adjusted parent rate back into struct
clk_rate_request.
This patch fixes this by saving the pristine parent clock rate, and
adding a copy that is adjusted and passed to the round() callback.
The pristine copy, if it is the best solution, would be saved back
to struct clk_rate_request.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to achieve all the rates asked by the GPU, we might need to change
the parent frequency.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The divider_get_val function that is used in our determine_rate callback
doesn't try to change the parent rate at all, while clk_divider_bestdiv,
used in divider_round_rate, does.
If we have a single parent, call divider_round_rate.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The Allwinner A10s, A13, R8 and NextThing GR8 are all based on the same
silicon, and all share the same clocks.
However, they're not packaged in the same way, and therefore not all the
controllers are actually available on all these SoCs.
Introduce a clock controller driver for all these SoCs with different
compatibles to take that into account.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks have a global pre-divider that applies to all their parents.
Since it might also apply to clocks that have a single parent, this is
merged in the ccu_common structure, unlike the other pre-divider settings
that are tied to a specific index, and thus a specific parent.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some multipliers have a maximum rate that is lower than what the register
width allows to. Add a field in the multiplier structure to allow CCU
driver to set that maximum.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The previous code was always taking 1 as the minimum in it's round_rate
function, ignoring entirely what was set as minimum in the clock
definition.
Make sure that's not the case anymore.
Fixes: 2beaa601c849 ("clk: sunxi-ng: Implement minimum for multipliers")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The factors we've seen so far all had an offset of one. However, on the
earlier Allwinner SoCs, some factors could have no offset at all, meaning
that the value computed to reach the rate we want to use was the one we had
to program in the registers.
Implement an additional field for the factors that can have such an offset
(linears, not based on a power of two) to specify that offset.
This offset is not linked to the extremums that can be specified in those
structures too. The minimum and maximum are representing the range of
values we can use to try to compute the best rate. The offset comes later
on when we want to set the best value in the registers.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks on the earlier SoCs such as the video PLLs are multipliers with
fractional settings.
Support those cases.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
V3s has a similar but cut-down CCU to H3. Some muxes, especially clocks
about CSI, are different, which makes it to need a new CCU driver.
Add such a new driver for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The audio DAI needs to set the clock rates of the ac-dig clock.
To make it possible, the parent PLL audio clock rates should
also be changed. This is possible via "CLK_SET_RATE_PARENT" flag.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As the SPDIF was rarely documented on the earlier Allwinner SoCs
it was assumed that it had a similar clock register to the one
described in the H3 User Manual.
However this is not the case and it looks to shares the same setup
as the I2S clock registers.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPUX clock on A33, which is for the Cortex-A7 cores, is designed to
be changeable by changing the rate of PLL_CPUX.
Add CLK_SET_RATE_PARENT flag to this clock.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When adjusting PLL_CPUX on A33, the PLL is temporarily driven too high,
and the system hangs.
Add a notifier to avoid this situation by temporarily switching to a
known stable 24 MHz oscillator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When adjusting PLL_CPUX on H3, the PLL is temporarily driven
too high, and the system becomes unstable (oopses or hangs).
Add a notifier to avoid this situation by temporarily switching
to a known stable 24 MHz oscillator.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Tested-by: Lutz Sammer <johns98@gmx.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In the user manual of A33 SoC, the bit 22 and 23 of pll-mipi control
register is called "LDO{1,2}_EN", and according to the BSP source code
from Allwinner [1], the LDOs are enabled during the clock's enabling
process.
The clock failed to generate output if the two LDOs are not enabled.
Add the two bits to the clock's gate bits, so that the LDOs are enabled
when the PLL is enabled.
[1] https://github.com/allwinner-zh/linux-3.4-sunxi/blob/master/drivers/clk/sunxi/clk-sun8iw5.c#L429
Fixes: d05c748bd730 ("clk: sunxi-ng: Add A33 CCU support")
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PLL-MIPI clock is somewhat special as it has its own LDOs which
need to be turned on for this PLL to actually work and output a clock
signal.
Add the 2 LDO enable bits to the gate bits. This fixes issues with
the TCON not sending vblank interrupts when the tcon and dot clock are
indirectly clocked from the PLL-MIPI clock.
Fixes: c6e6c96d8fa6 ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some checkpatch warnings about spaces were missed and we didn't
mark two structs as static. Clean it up.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The usual patches from us, but most notably the introduction of the A64
clocks unit.
-----BEGIN PGP SIGNATURE-----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=7+Az
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock changes from Maxime Ripard:
The usual patches from us, but most notably the introduction of the A64
clocks unit.
* tag 'sunxi-clk-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: sun8i-h3: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: sun8i-a23: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: Add A64 clocks
clk: sunxi-ng: Implement minimum for multipliers
clk: sunxi-ng: Add minimums for all the relevant structures and clocks
clk: sunxi-ng: Finish to convert to structures for arguments
clk: sunxi-ng: Remove the use of rational computations
clk: sunxi-ng: Rename the internal structures
clk: sunxi: mod0: improve function-level documentation
The audio module clocks are supposed to be set according to the sample
rate of the audio stream. The audio PLL provides the clock signal for
these module clocks, and only it is freely tunable.
Set CLK_SET_RATE_PARENT for the audio module clocks so their users can
properly tune the clock rate.
Fixes: 0577e4853bfb ("clk: sunxi-ng: Add H3 clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
