A debug level was added to the ath module for printing
MCI messages but no documentation was provided. Clarify that
MCI is the Message Coexistence Interface, a private protocol
used exclusively for WLAN-BT coexistence starting from
AR9462.
Cc: wtsao@qca.qualcomm.com
Cc: rmanohar@qca.qualcomm.com
Cc: mohammed@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of releasing and taking back the lock over and over again in the
tx path, hold the lock a bit longer, requiring much fewer lock/unlock pairs.
This makes locking much easier to review and should not have any noticeable
performance/latency impact.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tid->seq_next is initialized on A-MPDU start anyway, and the comment next
to this chunk of code seems to be bogus as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing A-MPDU tx status, only send a BAR for the failed packet
with the highest sequence number.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of limiting a subframe to 10 A-MPDU software transmission attempts,
count hardware retransmissions as well and raise the limit a bit. That way
there will be fewer software retransmission attempts when traffic suffers
from lots of hardware retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When compiling wl12xx for x86, there was a warning complaining about
the size of the buffer we were allocating in the stack:
drivers/net/wireless/wl12xx/debugfs.c: In function 'driver_state_read':
drivers/net/wireless/wl12xx/debugfs.c:380:1: warning: the frame size of 1040 bytes is larger than 1024 bytes
To prevent this, allocate the buffer in the heap instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl1271_configure_suspend_sta leaves a stale stack declared
completion in wlvif->ps_compl. Set it to NULL before returning.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[small fix to use wlvif->ps_compl instead of wl->ps_compl]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the newly introduced ieee80211_free_txskb() instead
of dev_kfree_skb() for failed tx packets.
Additionally, if the skb is a dummy packet, re-enqueue
it (as the fw expects it) instead of freeing it.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We need to set the extended radio parameters for wl127x only.
Currently, we were only calling this command with wl127x STA mode, but
we should also do it for AP mode.
Move the call to the extended radio paramaters to the common hw_init
and use a single if for the chip type to do everything at once.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We should not get an hlid value bigger than WL12XX_MAX_LINKS from
wl1271_rx_handle_data(). We have a WARN_ON in case it happens. But
despite the warning, we would still go ahead and write the hlid bit
into active_hlids (a stack variable). This would cause us to
overwrite other data in the stack.
To avoid this problem, we now skip the write when issuing the warning,
so at least we don't corrupt data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commit 80900d0140a7648587982c8f299830e900e49165 accidently broke
the ABI for testmode commands. Restore the ABI again.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Luciano Coelho <coelho@ti.com>
ieee80211_free_txskb should be used when dropping a frame in the device
rx path such that mac80211 knows about this frame being dropped.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg_workqueue was added to notify cfg80211 that scan, connect
or disconnect is done by calling respective completion handlers.
We can avoid use of this workqueue by calling those handlers
from other places.
1) Call connect, disconnect completion handlers in their callback
functions.
ex. Call cfg80211_connect_result() in mwifiex_cfg80211_connect()
2) Call scan completion handler after parsing response of last scan
command in a queue.
After removing the workqueue, variables (assoc_request etc.) and
checks used for mutual exclusion become redundant. Those are also
removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch
34a5b4b6af104cf18eb50748509528b9bdbc4036 iwlwifi: do not re-configure
HT40 after associated
Fix the case of HT40 after association on specified AP, but it break the
association for some APs and cause not able to establish connection.
We need to address HT40 before and after addociation.
CC: stable@vger.kernel.org #3.0+
Reported-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ted reported that he couldn't connect to some APs
and bisected it to the tx_sync implementation.
Disable it for the BSS context to fix this issue.
Reported-by: Ted Ts'o <tytso@mit.edu>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Command cancel path cancels the current command and moves
it to free command queue. While doing that it deletes the
command entry from the pending list. This is not correct
as the entry has been already deleted from the pending
list at 'mwifiex_exec_next_cmd'. Fixing it.
Also making sure the stale command pointer is cleaned and
unaccessible for later use.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables support for doing P2P management operations like device
discovery on top of a station interface. After group formation, the station
interface will become a P2P GO/client interface as the case may be.
This feature requires modifications to a couple of existing WMI structures and
therefore new command ids and structures have been defined in order to be
compatible with older firmware versions and other chips. The exception here is
the wmi_connect_cmd. Adding a new field to the end of the structure will not
cause any issues with previous firmware versions since firmware only checks for
minimum length of the command. The other structures are of variable length,
hence it was not possible to add new fields to the end.
The new command ids have to be added to the end of enum wmi_cmd_id, so it has
updated to match the firmware.
The driver will support both the 'old' and the 'new' commands for a while by
checking the firmware capabilities.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR6003 family use uart_tx=8 and refclk=26Mhz by default, and AR6004 family
uses different uart_tx pin and could also support various xtal source,
moves these per hw configuration.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mwifiex driver no longer supports it's own custom regulatory rules,
but custom regulatory domain capability is still advertised during
wiphy registration by the driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac driver has been verified on chipsets that were supported
when it was a pci device driver, ie. bcm4313, bcm43224, and bcm43225.
This patch restricts the driver to 802.11 core revisions that are found
in these chipsets.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of storing the buscore information now the BCMA core device
is kept for quick reference in si_info structure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of fields are no longer needed as the BCMA provides it
or makes them redundant. These have been removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In aiutils.c the selected core was maintained by its index number. This
is obsolete using BCMA functions so several functions using that index
have been removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function ai_switch_core() is no longer needed and its counterpart
ai_restore_core() as well, because interrupts disabling is not needed
anymore.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to interrupt disable/enable functionality any
longer due to BCMA usage assures the correct core is accessed
in any context.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macros were used to assure that the correct core was accessed in
the ISR, but register access is now done giving the explicit core so
no need to change interrupt state.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of functions in pmu.c are not used or adding no functionality
at all. These have been removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register access macros like R_REG/W_REG/etc. are no longer
needed as the driver uses the BCMA provided functions.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in aiutils.c now uses the BCMA function for control the
registers in the device cores.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in pmu.c now uses the functions provided by BCMA to
access the core registers.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in srom.c now uses the core access function provided by
BCMA so no need to pass __iomem pointer any longer.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in otp.c now uses the bcma core access functions to
read the OTP information from the device.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of returning the core index the function now returns
the bcma device for the requested core id. This function is
now exposed in the header file.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With previous patch "rtlwifi: use work for lps" we can now use mutex for
protecting ps mode changing critical sections. This fixes running system
with interrupts disabled for long time.
Merge ips_lock and lps_lock as they seems to protect the same data
structures (accessed in rtl_ps_set_rf_state() function).
Reported-by: Philipp Dreimann <philipp@dreimann.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Mike McCormack <mikem@ring3k.org>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Leaving leisure power save mode can take some time, so it's better to
perform that action in process context with interrupts enabled. This
patch changes lps_leave tasklet to work.
Reported-by: Philipp Dreimann <philipp@dreimann.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Mike McCormack <mikem@ring3k.org>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes were obtained from MMIO dump from 5.100.82.112.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
