[ Upstream commit b08134eb254db56e9ce8170d9b82f0d7a616b6f8 ]
After initial start-up, the driver triggers ATI (calibration) with
the newly loaded register configuration in place. Next, the driver
polls a register field to ensure ATI completed in a timely fashion
and that the device is ready to sense.
However, communicating with the device over I2C while ATI is under-
way may induce noise in the device and cause ATI to fail. As such,
the vendor recommends not to poll the device during ATI.
To solve this problem, let the device naturally signal to the host
that ATI is complete by way of an interrupt. A completion prevents
the device from successfully probing until this happens.
As an added benefit, initial switch states are now reported in the
interrupt handler at the same time ATI status is checked. As such,
duplicate code that reports initial switch states has been removed
from iqs269_input_init().
The former logic that scaled ATI timeout and filter settling delay
is not carried forward with the new implementation, as it produces
overly conservative delays at the lower clock rate.
Rather, a single timeout that covers both clock rates is used. The
filter settling delay does not happen to be necessary and has been
removed as well.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7RtB2T7AF9rYMjK@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18ab69c8ca5678324efbeed874b707ce7b2feae1 ]
Polling the device while it transitions from automatic to manual
power mode switching may keep the device from actually finishing
the transition. The process appears to time out depending on the
polling rate and the device's core clock frequency.
This is ultimately unnecessary in the first place; instead it is
sufficient to write the desired mode during initialization, then
disable automatic switching at suspend. This eliminates the need
to ensure the device is prepared for a manual change and removes
the 'suspend_mode' variable.
Similarly, polling the device while it transitions from one mode
to another under manual control may time out as well. This added
step does not appear to be necessary either, so drop it.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs+eEXlRw4Vq57@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa9f4275b20ec7b2a8fb05c66362d10b36f9efec ]
To discard false readings, one should use "ti,penirq-recheck-delay-usecs".
Checking get_pendown_state() at the beginning, most of the time fails
causing malfunctioning.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-4-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13f82ca3878db8284a70ef9711d7f710a31eb562 ]
Controllers that report pressure (e.g. ADS7846) use 5 commands and the
correct sequence is READ_X, READ_Y, READ_Z1, READ_Z2, PWRDOWN.
Controllers that don't report pressure (e.g. ADS7845/ADS7843) use only 3
commands and the correct sequence should be READ_X, READ_Y, PWRDOWN. But
the sequence sent was incorrect: READ_X, READ_Y, READ_Z1.
Fix this by setting the third (and last) command to PWRDOWN.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-3-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6965eece2a89c3f1d00881c6052ee1e987870c08 ]
Convert multiple full duplex transfers in to a single transfer to reduce
CPU load.
Current driver version support following filtering modes:
- ads7846_no_filter() - not filtered
- ads7846_debounce_filter() - driver specific debounce filter
- pdata->filter - platform specific debounce filter (do any platform
provides such filter?)
Without filter this HW is not really usable, since the physic of
resistive touchscreen can provide some bounce effects. With driver internal
filter, we have constant amount of retries + debounce retries if some anomaly
was detected.
High amount of tiny SPI transfers is the primer reason of high CPU load
and interrupt frequency.
This patch create one SPI transfer with all fields and not optional retires. If
bounce anomaly was detected, we will make more transfer if needed.
Without this patch, we will get about 10% CPU load on iMX6S on pen-down event.
For example by holding stylus on the screen.
With this patch, depending in the amount of retries, the CPU load will
be 1% with "ti,debounce-rep = <3>".
One buffer transfer allows us to use PIO FIFO or DMA engine, depending
on the platform.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-3-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 13f82ca3878d ("Input: ads7846 - always set last command to PWRDOWN")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c9509717b53e701469493a8d87ed42c7d782502 ]
Starting with 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845
controller support"), the ads7845 was partially converted to full duplex
mode.
Since it is not touchscreen controller specific, it is better to extend
this conversion to cover entire driver. This will reduce CPU load and make
driver more readable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-2-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 13f82ca3878d ("Input: ads7846 - always set last command to PWRDOWN")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3689abfc4e369a643d758a02fb9ad0b2403d6d6d ]
Unless it is being done as part of servicing a soft reset interrupt,
configuring channels on-the-fly (as is the case when writing to the
ati_trigger attribute) may cause GPIO3 (which reflects the state of
touch for a selected channel) to be inadvertently asserted.
To solve this problem, follow the vendor's recommendation and write
all channel configuration as well as the REDO_ATI register field as
part of a single block write. This ensures the device has been told
to re-calibrate itself following an I2C stop condition, after which
sensing resumes and GPIO3 may be asserted.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs8GyV7g0nF5Yy@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e023cc4abde3c01b895660b0e5a8488deb36b8c1 ]
The time the device takes to deassert its RDY output following an
I2C stop condition scales with the core clock frequency.
To prevent level-triggered interrupts from being reasserted after
the interrupt handler returns, increase the time before returning
to account for the worst-case delay (~140 us) plus margin.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs484ypy4dab5G@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59bc9cb3b80abaa42643abede0d5db8477901d9c ]
Each call to device/fwnode_get_named_child_node() must be matched
with a call to fwnode_handle_put() once the corresponding node is
no longer in use. This ensures a reference count remains balanced
in the case of dynamic device tree support.
Currently, the driver does not call fwnode_handle_put() on nested
event nodes. This patch solves this problem by adding the missing
instances of fwnode_handle_put().
As part of this change, the logic which parses each channel's key
code is gently refactored in order to reduce the number of places
from which fwnode_handle_put() is called.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/Y7Rsx68k/gvDVXAt@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c445d2637c938a800fcc8b5f0b10e60c94460c7 ]
The Clevo PCX0DX/TUXEDO XP1511, need quirks for the keyboard to not be
occasionally unresponsive after resume.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20230110134524.553620-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6a87c36165e6791eeaed88025cde270536c3198 ]
A lot of modern Clevo barebones have touchpad and/or keyboard issues after
suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of them
have an external PS/2 port so this can safely be set for all of them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use. No negative effects could be
observed when setting all four.
The list is quite massive as neither the TUXEDO nor the Clevo dmi strings
have been very consistent historically. I tried to keep the list as short
as possible without risking on missing an affected device.
This is revision 3. The Clevo N150CU barebone is still removed as it might
have problems with the fix and needs further investigations. The
SchenkerTechnologiesGmbH System-/Board-Vendor string variations are
added. This is now based in the quirk table refactor. This now also
includes the additional noaux flag for the NS7xMU.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-5-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff946268a0813c35b790dfbe07c3bfaa7bfb869c ]
Merge i8042 quirk tables to reduce code duplication for devices that need
more than one quirk. Before every quirk had its own table with devices
needing that quirk. If a new quirk needed to be added a new table had to
be created. When a device needed multiple quirks, it appeared in multiple
tables. Now only one table called i8042_dmi_quirk_table exists. In it every
device has one entry and required quirks are coded in the .driver_data
field of the struct dmi_system_id used by this table. Multiple quirks for
one device can be applied by bitwise-or of the new SERIO_QUIRK_* defines.
Also align quirkable options with command line parameters and make vendor
wide quirks per device overwriteable on a per device basis. The first match
is honored while following matches are ignored. So when a vendor wide quirk
is defined in the table, a device can inserted before and therefore
ignoring the vendor wide define.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-3-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95a9916c909f0b1d95e24b4232b4bc38ff755415 ]
Move __intconst from before i8042_dmi_laptop_table[] to after it for
consistent code styling.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-2-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3c44e2b6cde674797b76e76d3a903a63ce8a18bb upstream.
This reverts commit ac5408991ea6b06e29129b4d4861097c4c3e0d59 because
it causes loss of keyboard on HP 15-da1xxx.
Fixes: ac5408991ea6 ("Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode")
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/824effa5-8b9a-c28a-82bb-9b0ab24623e1@kernel.org
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1206358
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a85fbd6498441694475716a4d5c65f9d3e073faf ]
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
Fixes: afe10358e4 ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e13757f52496444b994a7ac67b6e517a15d89bbc ]
Like on the Acer Switch 10 SW5-012, the Acer Switch V 10 SW5-017's _LID
method messes with home- and power-button GPIO IRQ settings, causing an
IRQ storm.
Add a quirk entry for the Acer Switch V 10 to the dmi_use_low_level_irq[]
DMI quirk list, to use low-level IRQs on this model, fixing the IRQ storm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e9ada1d0e72b4737df400fe1bba48dc42a68df7 ]
It seems that the Windows drivers for the ACPI0011 soc_button_array
device use low level triggered IRQs rather then using edge triggering.
Some ACPI tables depend on this, directly poking the GPIO controller's
registers to clear the trigger type when closing a laptop's/2-in-1's lid
and re-instating the trigger when opening the lid again.
Linux sets the edge/level on which to trigger to both low+high since
it is using edge type IRQs, the ACPI tables then ends up also setting
the bit for level IRQs and since both low and high level have been
selected by Linux we get an IRQ storm leading to soft lockups.
As a workaround for this the soc_button_array already contains
a DMI quirk table with device models known to have this issue.
Add a module parameter for this so that users can easily test if their
device is affected too and so that they can use the module parameter
as a workaround.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e37cc6240767f794678d11704935d49cc81d59 ]
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac5408991ea6b06e29129b4d4861097c4c3e0d59 ]
The device works fine in native RMI mode, there is no reason to use legacy
PS/2 mode with it.
Signed-off-by: Aman Dhoot <amandhoot12@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81cd7e8489278d28794e7b272950c3e00c344e44 ]
Avoid resetting the module-wide i8042_platform_device pointer in
i8042_probe() or i8042_remove(), so that the device can be properly
destroyed by i8042_exit() on module unload.
Fixes: 9222ba68c3f4 ("Input: i8042 - add deferred probe support")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Link: https://lore.kernel.org/r/20221109034148.23821-1-chenjun102@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b8ebf250997c5fb253582f42bfe98673801ebebd upstream.
syzbot is reporting uninitialized value at iforce_init_device() [1], for
commit 6ac0aec6b0 ("Input: iforce - allow callers supply data buffer
when fetching device IDs") is checking that valid length is shorter than
bytes to read. Since iforce_get_id_packet() stores valid length when
returning 0, the caller needs to check that valid length is longer than or
equals to bytes to read.
Reported-by: syzbot <syzbot+4dd880c1184280378821@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 6ac0aec6b0 ("Input: iforce - allow callers supply data buffer when fetching device IDs")
Link: https://lore.kernel.org/r/531fb432-7396-ad37-ecba-3e42e7f56d5c@I-love.SAKURA.ne.jp
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17b9841152e7f4621619902b347e2cc39c32996 upstream.
Suspending and resuming the system can sometimes cause the out
URB to get hung after a reset_resume. This causes LED setting
and force feedback to break on resume. To avoid this, just drop
the reset_resume callback so the USB core rebinds xpad to the
wireless pads on resume if a reset happened.
A nice side effect of this change is the LED ring on wireless
controllers is now set correctly on system resume.
Cc: stable@vger.kernel.org
Fixes: 4220f7db1e ("Input: xpad - workaround dead irq_out after suspend/ resume")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Link: https://lore.kernel.org/r/20220818154411.510308-3-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e62563db857f81d75c5726a35bc0180bed6d1540 upstream.
Both i.MX6 and i.MX8 reference manuals list 0xBF8 as SNVS_HPVIDR1
(chapters 57.9 and 6.4.5 respectively).
Without this, trying to read the revision number results in 0 on
all revisions, causing the i.MX6 quirk to apply on all platforms,
which in turn causes the driver to synthesise power button release
events instead of passing the real one as they happen even on
platforms like i.MX8 where that's not wanted.
Fixes: 1a26c92071 ("Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q")
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4599101.ElGaqSPkdT@pliszka
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 425fe4709c76e35f93f4c0e50240f0b61b2a2e54 ]
This controller is used by PinePhone and PinePhone Pro. Support for
the PinePhone Pro will be added in a later patch set.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Jarrah Gosbell <kernel@undef.tools>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220809091200.290492-1-kernel@undef.tools
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99077ad668ddd9b4823cc8ce3f3c7a3fc56f6fd9 ]
Add the module alias so the rk805-pwrkey driver will
autoload when built as a module.
Fixes: 5a35b85c2d ("Input: add power key driver for Rockchip RK805 PMIC")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220612225437.3628788-1-pbrobinson@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 98e01215708b6d416345465c09dce2bd4868c67a upstream.
syzbot is reporting hung task at __input_unregister_device() [1], for
iforce_close() waiting at wait_event_interruptible() with dev->mutex held
is blocking input_disconnect_device() from __input_unregister_device().
It seems that the cause is simply that commit c2b27ef672 ("Input:
iforce - wait for command completion when closing the device") forgot to
call wake_up() after clear_bit().
Fix this problem by introducing a helper that calls clear_bit() followed
by wake_up_all().
Reported-by: syzbot <syzbot+deb6abc36aad4008f407@syzkaller.appspotmail.com>
Fixes: c2b27ef672 ("Input: iforce - wait for command completion when closing the device")
Tested-by: syzbot <syzbot+deb6abc36aad4008f407@syzkaller.appspotmail.com>
Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Co-developed-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/887021c3-4f13-40ce-c8b9-aa6e09faa3a7@I-love.SAKURA.ne.jp
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e61b3125a4f036b3c6b87ffd656fc1ab00440ae9 upstream.
The function ioremap() in gscps2_probe() can fail, so
its return value should be checked.
Fixes: 4bdc0d676a ("remove ioremap_nocache and devm_ioremap_nocache")
Cc: <stable@vger.kernel.org> # v5.6+
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: Xie Shaowen <studentxswpy@163.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit feedaacdadfc332e1a6e436f3adfbc67e244db47 ]
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab2e51898cd4343bbdf8587af8ce8fbabddbcb5 ]
Commit 223f61b8c5 ("Input: soc_button_array - add Lenovo Yoga Tablet2
1051L to the dmi_use_low_level_irq list") added the 1051L to this list
already, but the same problem applies to the 1051F. As there are no
further 1051 variants (just the F/L), we can just DMI match 1051.
Tested on a Lenovo Yoga Tablet2 1051F: Without this patch the
home-button stops working after a wakeup from suspend.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220603120246.3065-1-mail@mariushoch.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c42e65664390be7c1ef3838cd84956d3a2739d60 upstream.
The bcm5974 driver does the allocation and dma mapping of the usb urb
data buffer, but driver does not set the URB_NO_TRANSFER_DMA_MAP flag
to let usb core know the buffer is already mapped.
usb core tries to map the already mapped buffer, causing a warning:
"xhci_hcd 0000:00:14.0: rejecting DMA map of vmalloc memory"
Fix this by setting the URB_NO_TRANSFER_DMA_MAP, letting usb core
know buffer is already mapped by bcm5974 driver
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215890
Link: https://lore.kernel.org/r/20220606113636.588955-1-mathias.nyman@linux.intel.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f76955ab1e43e5795a9631b22ca4f918a0ae986 ]
The commit 26623eea0da3 attempted to deal with potential leak of runtime
PM counter when opening the touchscreen device, however it ended up
erroneously dropping the counter in the case of successfully enabling the
device.
Let's address this by using pm_runtime_resume_and_get() and then executing
pm_runtime_put_sync() only when we fail to send "sense on" command to the
device.
Fixes: 26623eea0da3 ("Input: stmfts - fix reference leak in stmfts_input_open")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8994b30d71d64d5dcc9bc0edbfdf367171aa96f ]
of_find_node_by_path() calls of_find_node_opts_by_path(),
which returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 9c1a5077fd ("input: Rewrite sparcspkr device probing.")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220516081018.42728-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e4920d42ce0e9c8aafb7f64b6d9d4ae02161e51e upstream.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c8035 ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26623eea0da3476446909af96c980768df07bbd9 ]
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stmfts_input_open, so we should fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220317131604.53538-1-zhengyongjun3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 409353cbe9fe48f6bc196114c442b1cff05a39bc ]
Update input_set_capability() to prevent kernel panic in case the
event code exceeds the bitmap for the given event type.
Suggested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220320032537.545250-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fd269e74f2feec973f45ee11d822faeda4fe284 ]
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8b188fba75195745026e11d408e4a7e94e01d701 upstream.
This reverts commit 37ef4c19b4c659926ce65a7ac709ceaefb211c40.
The touchpad present in the Dell Precision 7550 and 7750 laptops
reports a HID_DG_BUTTONTYPE of type MT_BUTTONTYPE_CLICKPAD. However,
the device is not a clickpad, it is a touchpad with physical buttons.
In order to fix this issue, a quirk for the device was introduced in
libinput [1] [2] to disable the INPUT_PROP_BUTTONPAD property:
[Precision 7x50 Touchpad]
MatchBus=i2c
MatchUdevType=touchpad
MatchDMIModalias=dmi:*svnDellInc.:pnPrecision7?50*
AttrInputPropDisable=INPUT_PROP_BUTTONPAD
However, because of the change introduced in 37ef4c19b4 ("Input: clear
BTN_RIGHT/MIDDLE on buttonpads") the BTN_RIGHT key bit is not mapped
anymore breaking the device right click button and making impossible to
workaround it in user space.
In order to avoid breakage on other present or future devices, revert
the patch causing the issue.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220321184404.20025-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e941dc13fd3717122207d74539ab95da07ef797f ]
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5600f6986628dde8881734090588474f54a540a8 upstream.
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba115adf61b36b8c167126425a62b0efc23f72c0 upstream.
Make the samsung-keypad driver explicitly depend on CONFIG_HAS_IOMEM, as it
calls devm_ioremap(). This prevents compile errors in some configs (e.g,
allyesconfig/randconfig under UML):
/usr/bin/ld: drivers/input/keyboard/samsung-keypad.o: in function `samsung_keypad_probe':
samsung-keypad.c:(.text+0xc60): undefined reference to `devm_ioremap'
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: anton ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20220225041727.1902850-1-davidgow@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b7762e37c95d9b965d16bb0e18dbd1fa2e2861 upstream.
Before these changes elan_suspend() would only disable the regulator
when device_may_wakeup() returns false; whereas elan_resume() would
unconditionally enable it, leading to an enable count imbalance when
device_may_wakeup() returns true.
This triggers the "WARN_ON(regulator->enable_count)" in regulator_put()
when the elan_i2c driver gets unbound, this happens e.g. with the
hot-plugable dock with Elan I2C touchpad for the Asus TF103C 2-in-1.
Fix this by making the regulator_enable() call also be conditional
on device_may_wakeup() returning false.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a36d8ce554b82b0a08e2b95d0bd44fcbff339b upstream.
elan_disable_power() is called conditionally on suspend, where as
elan_enable_power() is always called on resume. This leads to
an imbalance in the regulator's enable count.
Move the regulator_[en|dis]able() calls out of elan_[en|dis]able_power()
in preparation of fixing this.
No functional changes intended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-1-hdegoede@redhat.com
[dtor: consolidate elan_[en|dis]able() into elan_set_power()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 37ef4c19b4c659926ce65a7ac709ceaefb211c40 ]
Buttonpads are expected to map the INPUT_PROP_BUTTONPAD property bit
and the BTN_LEFT key bit.
As explained in the specification, where a device has a button type
value of 0 (click-pad) or 1 (pressure-pad) there should not be
discrete buttons:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/touchpad-windows-precision-touchpad-collection#device-capabilities-feature-report
However, some drivers map the BTN_RIGHT and/or BTN_MIDDLE key bits even
though the device is a buttonpad and therefore does not have those
buttons.
This behavior has forced userspace applications like libinput to
implement different workarounds and quirks to detect buttonpads and
offer to the user the right set of features and configuration options.
For more information:
https://gitlab.freedesktop.org/libinput/libinput/-/merge_requests/726
In order to avoid this issue clear the BTN_RIGHT and BTN_MIDDLE key
bits when the input device is register if the INPUT_PROP_BUTTONPAD
property bit is set.
Notice that this change will not affect udev because it does not check
for buttons. See systemd/src/udev/udev-builtin-input_id.c.
List of known affected hardware:
- Chuwi AeroBook Plus
- Chuwi Gemibook
- Framework Laptop
- GPD Win Max
- Huawei MateBook 2020
- Prestigio Smartbook 141 C2
- Purism Librem 14v1
- StarLite Mk II - AMI firmware
- StarLite Mk II - Coreboot firmware
- StarLite Mk III - AMI firmware
- StarLite Mk III - Coreboot firmware
- StarLabTop Mk IV - AMI firmware
- StarLabTop Mk IV - Coreboot firmware
- StarBook Mk V
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20220208174806.17183-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
