Pratyush Anand ce21bfe603 USB: Add LVS Test device driver
OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
system (SS-OVS) which consists of an excersizer and analyzer.

USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
Link Layer Validation (LVS).

Some modifications are needed for an embedded Linux USB host to pass all
these tests.  Most of these tests require just Link to be in U0. They do
not work with default Linux USB stack since, default stack does port
reset and then starts sending setup packet, which is not expected by
Link Layer Validation (LVS) device of Lecroy Compliance Suit.  Then,
There are many Link Layer Tests which need host to generate specific
traffic.

This patch supports specific traffic generation cases. As of now all the
host Lecroy Link Layer-USBIF tests (except TD7.26) passes
with this patch for single run using  Lecroy USB Compliance Suite
Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
Build 1603. Therefore patch seems to be a good candidate for inclusion.
Further modification can be done on top of it.

lvstest driver will not bind to any device by default. It can bind
manually to a super speed USB host controller root hub. Therefore, regular
hub driver must be unbound before this driver is bound. For example, if
2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.

 echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind

Then write Linux Foundation's vendor ID which is used by root hubs and
SS root hub's device ID into new_id file. Writing IDs into new_id file
will also bind the lvs driver with any available SS root hub interfaces.

 echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id

Now connect LVS device with root hub port.

Test case specific traffic can be generated as follows whenever needed:

1. To issue "Get Device descriptor" command for TD.7.06:
 echo  > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc

2. To set U1 timeout to 127 for TD.7.18
 echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout

3. To set U2 timeout to 0 for TD.7.18
 echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout

4. To issue "Hot Reset" for TD.7.29
 echo  > /sys/bus/usb/devices/2-0\:1.0/hot_reset

5. To issue "U3 Entry" for TD.7.35
 echo  > /sys/bus/usb/devices/2-0\:1.0/u3_entry

6. To issue "U3 Exit" for TD.7.36
 echo  > /sys/bus/usb/devices/2-0\:1.0/u3_exit

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17 17:11:09 -07:00
..
2014-07-17 17:11:09 -07:00

This directory attempts to document the ABI between the Linux kernel and
userspace, and the relative stability of these interfaces.  Due to the
everchanging nature of Linux, and the differing maturity levels, these
interfaces should be used by userspace programs in different ways.

We have four different levels of ABI stability, as shown by the four
different subdirectories in this location.  Interfaces may change levels
of stability according to the rules described below.

The different levels of stability are:

  stable/
	This directory documents the interfaces that the developer has
	defined to be stable.  Userspace programs are free to use these
	interfaces with no restrictions, and backward compatibility for
	them will be guaranteed for at least 2 years.  Most interfaces
	(like syscalls) are expected to never change and always be
	available.

  testing/
	This directory documents interfaces that are felt to be stable,
	as the main development of this interface has been completed.
	The interface can be changed to add new features, but the
	current interface will not break by doing this, unless grave
	errors or security problems are found in them.  Userspace
	programs can start to rely on these interfaces, but they must be
	aware of changes that can occur before these interfaces move to
	be marked stable.  Programs that use these interfaces are
	strongly encouraged to add their name to the description of
	these interfaces, so that the kernel developers can easily
	notify them if any changes occur (see the description of the
	layout of the files below for details on how to do this.)

  obsolete/
  	This directory documents interfaces that are still remaining in
	the kernel, but are marked to be removed at some later point in
	time.  The description of the interface will document the reason
	why it is obsolete and when it can be expected to be removed.

  removed/
	This directory contains a list of the old interfaces that have
	been removed from the kernel.

Every file in these directories will contain the following information:

What:		Short description of the interface
Date:		Date created
KernelVersion:	Kernel version this feature first showed up in.
Contact:	Primary contact for this interface (may be a mailing list)
Description:	Long description of the interface and how to use it.
Users:		All users of this interface who wish to be notified when
		it changes.  This is very important for interfaces in
		the "testing" stage, so that kernel developers can work
		with userspace developers to ensure that things do not
		break in ways that are unacceptable.  It is also
		important to get feedback for these interfaces to make
		sure they are working in a proper way and do not need to
		be changed further.


How things move between levels:

Interfaces in stable may move to obsolete, as long as the proper
notification is given.

Interfaces may be removed from obsolete and the kernel as long as the
documented amount of time has gone by.

Interfaces in the testing state can move to the stable state when the
developers feel they are finished.  They cannot be removed from the
kernel tree without going through the obsolete state first.

It's up to the developer to place their interfaces in the category they
wish for it to start out in.


Notable bits of non-ABI, which should not under any circumstances be considered
stable:

- Kconfig.  Userspace should not rely on the presence or absence of any
  particular Kconfig symbol, in /proc/config.gz, in the copy of .config
  commonly installed to /boot, or in any invocation of the kernel build
  process.

- Kernel-internal symbols.  Do not rely on the presence, absence, location, or
  type of any kernel symbol, either in System.map files or the kernel binary
  itself.  See Documentation/stable_api_nonsense.txt.