TCPCI spec allows TCPC hardware to autonomously discharge the vbus
capacitance upon disconnect. The expectation is that the TCPM enables
AutoDischargeDisconnect while entering SNK/SRC_ATTACHED states. Hardware
then automously discharges vbus when the vbus falls below a certain
threshold i.e. VBUS_SINK_DISCONNECT_THRESHOLD.
Apart from enabling the vbus discharge circuit, AutoDischargeDisconnect
is also used a flag to move TCPCI based TCPC implementations into
Attached.Snk/Attached.Src state as mentioned in
Figure 4-15. TCPC State Diagram before a Connection of the
USB Type-C Port Controller Interface Specification.
In such TCPC implementations, setting AutoDischargeDisconnect would
prevent TCPC into entering "Connection_Invalid" state as well.
Bug: 168555244
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-8-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit f321a02caehttps://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-next)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
(cherry picked from commit e9a276bd2a70537eab1b4162cca9b7eeb0f1514a)
(cherry picked from commit a53a13168af75458cc57fe1e7a0e1129562fcd1a)
Signed-off-by: Will McVicker <willmcvicker@google.com>
(cherry picked from commit 303a32911f5aca961031f4c1d57ee9c713f9e6cb)
Signed-off-by: Will McVicker <willmcvicker@google.com>
Change-Id: I3e25e9045c335b48cefaddb70329dd4df7e0fd94
TD.4.7.3. Try SNK DRP Connect Try.SRC DRP fails. The compliance
tester mimics being a Try.SRC USB-C port.
The failure is due to TCPM exiting SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS
when VBUS is not present eventhough when SNK.Rp is seen. Exit to
SRC_TRYWAIT from SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS only when SNK.Rp
is not seen for PD_T_TRY_CC_DEBOUNCE.
>From the spec:
The port shall then transition to Attached.SNK when the SNK.Rp state
is detected on exactly one of the CC1 or CC2 pins for at least
tTryCCDebounce and VBUS is detected. Alternatively, the port shall
transition to TryWait.SRC if SNK.Rp state is not detected for
tTryCCDebounce.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201125014804.1596719-1-badhri@google.com
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Power Delivery Specification R3.0 introduced separate
field for the DFP product type to the ID Header VDO.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201125120642.37156-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a field to the typec_plug struct to record the number of available
altmodes as well as the corresponding sysfs attribute to expose this to
userspace.
This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the plug. The sysfs file remains
hidden as long as the attribute value is -1.
We re-use the partner attribute for number_of_alternate_modes since the
usage and name is similar, and update the corresponding *_show() command
to support both partner and plugs.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-4-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPCI spec allows TCPC hardware to autonomously discharge the vbus
capacitance upon disconnect. The expectation is that the TCPM enables
AutoDischargeDisconnect while entering SNK/SRC_ATTACHED states. Hardware
then automously discharges vbus when the vbus falls below a certain
threshold i.e. VBUS_SINK_DISCONNECT_THRESHOLD.
Apart from enabling the vbus discharge circuit, AutoDischargeDisconnect
is also used a flag to move TCPCI based TCPC implementations into
Attached.Snk/Attached.Src state as mentioned in
Figure 4-15. TCPC State Diagram before a Connection of the
USB Type-C Port Controller Interface Specification.
In such TCPC implementations, setting AutoDischargeDisconnect would
prevent TCPC into entering "Connection_Invalid" state as well.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-8-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-5-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a user-visible attribute for the number of alternate modes available
in a partner. This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the partner.
Also add a sysfs file which exposes this attribute. The file remains
hidden as long as the attribute value is -1.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-3-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Power Delivery Specification R3.0 adds a captive cable type
to the "USB Type-C plug to USB Type-C/Captive" field (Bits 19-18,
Passive/Active Cable VDO, Table 6-38 & 6-39).
Add the corresponding definition to the Cable VDO header. Also add a
helper macro to get the Type C cable connector type, when provided
the cable VDO.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two bits support for the Thunderbolt rounded/non-rounded cable has been
added to the header file.
Hence, removing unused TBT_CABLE_ROUNDED definition from the header file.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--
changes in v2:
- Removed the fixes tag as there is no functional implication.
--
Link: https://lore.kernel.org/r/20201113202503.6559-5-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rounded and non-rounded Thunderbolt cables are represented by two bits as
per USB Type-C Connector specification v2.0 section F.2.6.
Corrected that in the Thunderbolt 3 cable discover mode VDO.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--
Changes in v2:
- Removed the fixes tag as there is no functional implication.
--
Link: https://lore.kernel.org/r/20201113202503.6559-2-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last user of RUN_CONTEXT was removed in commit
97c17beb3b668 ("[PATCH] ehci-hcd (1/2): portability (2.4), tasklet,")
in the history.git repo.
There are no users of RUN_CONTEXT, remove it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20201113212704.2243807-1-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace usbnet_get_stats64() with new identical core function
dev_get_tstats64() in all users and remove usbnet_get_stats64().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of usbnet for storing a pointer
to the per-cpu counters. This allows us to use core functionality for
statistics handling.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support ECM mode based on cdc_ether with relative mii functions,
when CONFIG_USB_RTL8152 is not set, or the device is not supported
by r8152 driver.
Both r8152 and r8153_ecm would check the return value of
rtl8152_get_version() in porbe(). If rtl8152_get_version()
return none zero value, the r8152 is used for the device
with vendor mode. Otherwise, the r8153_ecm is used for the
device with ECM mode.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/1394712342-15778-392-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The digi_acceleport driver is the only driver still using the port
write wake queue so move it to that driver's port data.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There is a common comment marked, instead, with kernel-doc
notation.
Also, some identifiers have different names between their
prototypes and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/0b964be3884def04fcd20ea5c12cb90d0014871c.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steps on the way to 5.10-rc1
Resolves conflicts in:
fs/userfaultfd.c
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Ie3fe3c818f1f6565cfd4fa551de72d2b72ef60af
Steps on the way to 5.10-rc1
Fixes merges in:
drivers/usb/typec/tcpm/tcpm.c
include/linux/usb/tcpm.h
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Ie6de88b6cdc3415679c2f931fc03147a7609d333
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl+JNGYACgkQCF8+vY7k
4RV/TA//ZoRoMQE5B6zwO4kOGILMbmW2uepjoEysLgus2ctkTUoRkpNLWS3SozcU
6c/eW1rC4Fji24te6lwusciZa5zQgbGMjFYk1LhnJ65lJA+kQ+kV1DGz/ZWtklMM
gLX20+tQADqGl+u2dmFCvmRhPWJ9nzt1C0auN7dGeu+9g97GnhKG6o2Kv/nVCb68
qMmAs9UrfN24DO5G1ixkdY08nSNJPrpgQnIR2ruUysUII/yTTtcnmHDbH3WWL6+9
2P87AZ6zsa3FdBhAjmG5YJklQgPkLFWEykHMTqq/Mkcpff/JB/AayrL6XNB2QoZb
YXLHJp3Na6iBmdmHhecg+VQDgz28UfMk+p+HFoJh8RTtJa9/qJvYdJmIE/mUPrnY
gL4jNgMVwkptGHXh7IRuSLysT5heJPMQss6TfZ6yYadeOIpx7W8MCAYnGffiElLQ
hmKdmyCszS3SERJz40EOBdr2NQYcDEUt2NtEhdVfium21A4PFOdJlCejifGhJyzP
n1QcyMXHnh/d4zecA6fcD0LVyxBgngeKEvdtOLZJ1ubxWwHhgWTN8R4HedoN2Nb9
cLEUK8Td+9n2RVS8UED4BBI+6vfN3Y6Syjvy8qD3pCs4SBcu3k790mf47t2QhkEq
+Ho06gdrGJdEcSDO8zVY7qjZX/GX/dbRHCb5CRokL5FmNWhXd/Y=
=26wi
-----END PGP SIGNATURE-----
Merge tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull documentation updates from Mauro Carvalho Chehab:
"A series of patches addressing warnings produced by make htmldocs.
This includes:
- kernel-doc markup fixes
- ReST fixes
- Updates at the build system in order to support newer versions of
the docs build toolchain (Sphinx)
After this series, the number of html build warnings should reduce
significantly, and building with Sphinx 3.1 or later should now be
supported (although it is still recommended to use Sphinx 2.4.4).
As agreed with Jon, I should be sending you a late pull request by the
end of the merge window addressing remaining issues with docs build,
as there are a number of warning fixes that depends on pull requests
that should be happening along the merge window.
The end goal is to have a clean htmldocs build on Kernel 5.10.
PS. It should be noticed that Sphinx 3.0 is not currently supported,
as it lacks support for C domain namespaces. Such feature, needed in
order to document uAPI system calls with Sphinx 3.x, was added only on
Sphinx 3.1"
* tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (75 commits)
PM / devfreq: remove a duplicated kernel-doc markup
mm/doc: fix a literal block markup
workqueue: fix a kernel-doc warning
docs: virt: user_mode_linux_howto_v2.rst: fix a literal block markup
Input: sparse-keymap: add a description for @sw
rcu/tree: docs: document bkvcache new members at struct kfree_rcu_cpu
nl80211: docs: add a description for s1g_cap parameter
usb: docs: document altmode register/unregister functions
kunit: test.h: fix a bad kernel-doc markup
drivers: core: fix kernel-doc markup for dev_err_probe()
docs: bio: fix a kerneldoc markup
kunit: test.h: solve kernel-doc warnings
block: bio: fix a warning at the kernel-doc markups
docs: powerpc: syscall64-abi.rst: fix a malformed table
drivers: net: hamradio: fix document location
net: appletalk: Kconfig: Fix docs location
dt-bindings: fix references to files converted to yaml
memblock: get rid of a :c:type leftover
math64.h: kernel-docs: Convert some markups into normal comments
media: uAPI: buffer.rst: remove a left-over documentation
...
The typec_bus.rst asks for documentation of those two
functions, but they don't exist:
./drivers/usb/typec/bus.c:1: warning: 'typec_altmode_unregister_driver' not found
./drivers/usb/typec/bus.c:1: warning: 'typec_altmode_register_driver' not found
Also, they're not declared on bus.c but, instead, at a header
file (typec_altmode.h).
So, add documentation for both functions at the header and
change the kernel-doc markup under typec_bus.rst to point
to the right place.
While here, also place the documentation for both structs
declared on typec_altmode.h at the rst file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.
Once the explicit contract is negotiated, sink port is
expected to query the source port for sink caps to
determine whether the source is FRS capable.
Bits 23 & 24 of fixed pdo of the sink caps from the source, when
set, indicates the current needed by the source when fast role
swap is in progress(Implicit contract phasae). 0 indicates that
the source does not support Fast Role Swap.
Upon receiving the FRS signal from the source,
TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.
1. TCPM sends FRS PD message: FR_SWAP_SEND
2. If response is not received within the expiry of
SenderResponseTimer, Error recovery is triggered.:
FR_SWAP_SEND_TIMEOUT
3. Upon receipt of the accept message, TCPM waits for
PSSourceOffTimer for PS_READY message from the partner:
FR_SWAP_SNK_SRC_NEW_SINK_READY.
TCPC is expected to autonomously turn on vbus once the FRS
signal is received and vbus voltage falls below vsafe5v within
tSrcFrSwap. This is different from traditional power role swap
where the vbus sourcing is turned on by TCPM.
4. By this time, TCPC most likely would have started to
source vbus, TCPM waits for tSrcFrSwap to see if the
lower level TCPC driver signals TCPM_SOURCING_VBUS event:
FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
changes the CC pin from Rd to Rp. This is the end of fast
role swap sequence and TCPM initiates the sequnce to negotiate
explicit contract by transitioning into SRC_STARTUP after
SwapSrcStart.
The code is written based on the sequence described in "Figure 8-107:
Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
USB Power Delivery Specification Revision 3.0, Version 1.2.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-7-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
-----BEGIN PGP SIGNATURE-----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=e08s
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.10 merge window
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
usb: dwc2: override PHY input signals with usb role switch support
dt-bindings: usb: dwc2: add optional usb-role-switch property
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
usb: dwc3: gadget: Support up to max stream id
usb: dwc3: gadget: Return early if no TRB update
usb: dwc3: gadget: Keep TRBs in request order
usb: dwc3: gadget: Revise setting IOC when no TRB left
usb: dwc3: gadget: Look ahead when setting IOC
usb: dwc3: gadget: Allow restarting a transfer
usb: bdc: remove duplicated error message
usb: dwc3: Stop active transfers before halting the controller
usb: cdns3: gadget: enlarge the TRB ring length
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
usb: cdns3: gadget: need to handle sg case for workaround 2 case
usb: cdns3: gadget: handle sg list use case at completion correctly
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
...
This patch adds a function that converts power operation mode string into
power operation mode value.
It is useful to configure power operation mode through device tree
property, as power capabilities may be linked to hardware design.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-3-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The routines used by the UDC core to interface with the kernel's
device model, namely usb_add_gadget_udc(),
usb_add_gadget_udc_release(), and usb_del_gadget_udc(), provide access
to only a subset of the device model's full API. They include
functionality equivalent to device_register() and device_unregister()
for gadgets, but they omit device_initialize(), device_add(),
device_del(), get_device(), and put_device().
This patch expands the UDC API by adding usb_initialize_gadget(),
usb_add_gadget(), usb_del_gadget(), usb_get_gadget(), and
usb_put_gadget() to fill in the gap. It rewrites the existing
routines to call the new ones.
CC: Anton Vasilyev <vasilyev@ispras.ru>
CC: Evgeny Novikov <novikov@ispras.ru>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
https://lkml.org/lkml/2019/2/12/701 removed
tcpm_update_sink_capabilities. However, Pixel started using this
at a later point in time. The client code is not in upstream
though.
Bug: 169695061
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Change-Id: Icb206c902187c90b38dd14924987725e9977e47c
TCPC validation revealed that when the Type-C port is exposed
to water, TCPC stops toggling while reporting Rp or Rd
in CC pins. However, At the end of debounce period, CC pins
report OPEN state which causes TCPM to re-enable toggling.
The loop continues to happen and keeps the cpu busy and
burns power while wasting cpu cycles.
To overcome this issue, When TCPM detects CC open at the end of
debounce, call chip level callbacks to check for contaminant
in the connector.
Bug: 168544734
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Change-Id: If28027bdacfdf8511be0ea54766970fb73bc3d96
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steps on the way to 5.9-rc1
Resolves conflicts in:
drivers/irqchip/qcom-pdc.c
include/linux/device.h
net/xfrm/xfrm_state.c
security/lsm_audit.c
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I4aeb3d04f4717714a421721eb3ce690c099bb30a
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl8g2ksACgkQSFkpgVDW
cbtAMwf/dkrCfmE2HpvAsZqL68WOC1yTaN9f3v7bzXc2oD2WRsk3aKGZGLeXvMtN
aruD3ctxOVEom5FHrff8x3G1CBw8wsbl+yjT6aTlbcFY/Yzmww7RABUO5Xp1F9aB
aTuDcLeoY22UHkzNdeNrixEuOR9xeyhZjFybW0cZ6FddP0mj4SUNNczxfaGvmLLI
DOJ7oc8KC9pIwhoF9065GH0p5PrXVnZvcBUXWs5PASjj4lWb3DiMGxhZRPBLbB6l
YifzRa+C90BP4AjTptS03fD/3knciZCM8Z1GsVYdKLuO4NOPlcZeEJEeUGmkCr0L
QmOpk5Sh8nACisOCqn3gQDo7jAI6Mg==
=JnWY
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
ENDIAN issue fix and one query controller role API is introduced.
* tag 'usb-ci-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: get available runtime dr mode for wakeup setting
usb: chipidea: add query_available_role interface
Documentation: ABI: usb: chipidea: Update Li Jun's e-mail
usb: chipidea: udc: fix the ENDIAN issue
Here are the USB-serial updates for 5.9-rc1, including:
- console flow-control support
- simulated line-breaks on some ch341
- hardware flow-control fixes for cp210x
- break-detection and sysrq fixes for ftdi_sio
- sysrq optimisations
- input parity checking for cp210x
Included are also some new device ids and various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXyAjIwAKCRALxc3C7H1l
CHruAQDTSejnRcrxMqU6mqL2AuEw+fABGUxjE+ah/HbXMf7CDwD/d0XQFimA8U8J
ovxTVm35R+vYQ7T7jTNuVxso6nWGxw8=
=15J7
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.9-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.9-rc1
Here are the USB-serial updates for 5.9-rc1, including:
- console flow-control support
- simulated line-breaks on some ch341
- hardware flow-control fixes for cp210x
- break-detection and sysrq fixes for ftdi_sio
- sysrq optimisations
- input parity checking for cp210x
Included are also some new device ids and various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.9-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (31 commits)
USB: serial: qcserial: add EM7305 QDL product ID
USB: serial: iuu_phoenix: fix led-activity helpers
USB: serial: sierra: clean up special-interface handling
USB: serial: cp210x: use in-kernel types in port data
USB: serial: cp210x: drop unnecessary packed attributes
USB: serial: cp210x: add support for TIOCGICOUNT
USB: serial: cp210x: add support for line-status events
USB: serial: cp210x: disable interface on errors in open
USB: serial: drop redundant transfer-buffer casts
USB: serial: drop extern keyword from function declarations
USB: serial: drop unnecessary sysrq include
USB: serial: add sysrq break-handler dummy
USB: serial: inline sysrq dummy function
USB: serial: only process sysrq when enabled
USB: serial: only set sysrq timestamp for consoles
USB: serial: ftdi_sio: fix break and sysrq handling
USB: serial: ftdi_sio: clean up receive processing
USB: serial: ftdi_sio: make process-packet buffer unsigned
USB: serial: use fallthrough pseudo-keyword
USB: serial: ch341: fix missing simulated-break margin
...
The glue layer may need to know current available role to do some
setting, eg, the wakeup setting. So we add ci_hdrc_query_available_role
for that.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719160910.60018-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port starts to toggle when transitioning to unattached state.
This is incorrect while in BIST mode.
6.4.3.1 BIST Carrier Mode
Upon receipt of a BIST Message, with a BIST Carrier Mode BIST Data Object,
the UUT Shall send out a continuous string of BMC encoded alternating "1"s
and “0”s. The UUT Shall exit the Continuous BIST Mode within
tBISTContMode of this Continuous BIST Mode being enabled(see
Section 6.6.7.2).
6.4.3.2 BIST Test Data
Upon receipt of a BIST Message, with a BIST Test Data BIST Data Object,
the UUT Shall return a GoodCRC Message and Shall enter a test mode in which
it sends no further Messages except for GoodCRC Messages in response to
received Messages. See Section 5.9.2 for the definition of the Test Data
Frame. The test Shall be ended by sending Hard Reset Signaling to reset the
UUT.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200716034128.1251728-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM supports BIST carried mode. PD compliance tests require
BIST Test Data to be supported as well.
Introducing set_bist_data callback to signal tcpc driver for
configuring the port controller hardware to enable/disable
BIST Test Data mode.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200716034128.1251728-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function can be reused by other usbnet minidrivers.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the function available to other drivers, like cdc_ncm.
Signed-off-by: Miguel Rodríguez Pérez <miguel@det.uvigo.gal>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the redundant extern keyword from function declarations in the
subsystem header file to improve readability (and make it easier to spot
the global variables).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to include sysrq.h in the subsystem header.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add inline sysrq break-handler dummy to allow the compiler to eliminate
further code when either console or sysrq support isn't enabled and to
clearly mark the two sysrq functions as belonging together.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Inline the dummy sysrq character handling when either console support or
magic-sysrq support isn't enabled to allow the compiler to eliminate
unused code.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB is a HOST/DEVICE protocol, as per the specification and all
documentation. Fix up terms that are not applicable to make things
match up with the terms used through the rest of the USB stack.
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20200701171555.3198836-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This data structure can be delivered to the mux drivers when
Enter_USB Message is used exactly the same way as the
Alternate Mode specific data structures are delivered to the
mux drivers when Enter Mode Messages are used.
The Enter_USB data structure shall have all details related
to the Enter_USB Message, most importantly the Enter_USB
Date Object that was used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200701115618.22482-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Required backing out the renesas-xhci changes that never made it
upstream yet. If they are really needed, someone will work to get them
merged upstream properly...
Baby steps on the way to 5.8-rc1.
Change-Id: I6a450d3630c6d015d0e4cd00068fa7c702b96f41
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The USB core has a quirk flag to ignore specific endpoints, so rename it
to be more obvious what this quirk does.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Richard Dodd <richard.o.dodd@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cox <jonathan@jdcox.net>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: "Thiébaud Weksteen" <tweek@google.com>
Cc: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200618094300.1887727-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Support imx7d USB charger
- Add software sg support for UDC
- Enable user trigger role switch
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl7Mf1oACgkQSFkpgVDW
cbskgggAvRbKPI2Zbw4tHa1JgwkADxg2Q3ewxFLiNIJ7GVLpZeiBn4Dziong6za9
1tB/f4qVyAlVT/zLYrxo9oCMwmGOLJjxigGLqJ2iMtDqcRG++jCdirTMXiI2Fdlh
ZCup49W0IWKmQ7mSLK0TDVbEpYT8YOICiCJumMxhMYuP6bfgFihPjh8NTiz4X7Jr
SUw5rCS7qTRAwDeywIbzWIeCmc4MKaohx4t/XD4Xxz0rPvJrkPgZAaiPh9vJzyMh
2XgFZovLin46QaVbSxxhTUJ7PitCQYzXF+W5vqsdtHkj2u3N3o0MPbSDCKT3oYUb
2zLS7SHzHuKmgFSnxOcLI56gF32uHg==
=YwB9
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Some improvments for ci_hdrc_usb2.c
- Support imx7d USB charger
- Add software sg support for UDC
- Enable user trigger role switch
* tag 'usb-ci-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: Enable user-space triggered role-switching
usb: chipidea: udc: add software sg list support
usb: chipidea: usbmisc_imx: using different ops for imx7d and imx7ulp
usb: chipidea: pull down dp for possible charger detection operation
usb: chipidea: introduce imx7d USB charger detection
usb: chipidea: introduce CI_HDRC_CONTROLLER_VBUS_EVENT glue layer use
usb: chipidea: usb2: remove unneeded semicolon
usb: chipidea: allow disabling glue drivers if EMBEDDED
usb: chipidea: usb2: absorb zevio glue driver
usb: chipidea: usb2: make clock optional
usb: chipidea: usb2: fix formatting
usb: chipidea: usb2: constify zynq_pdata
usb: chipidea: core: show the real pointer value for register
usb: chipidea: core: refine the description for this driver
usb: chipidea: udc: fix the kernel doc for udc.h
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEElLzh7wn96CXwjh2IzL64meEamQYFAl7LktsRHGJhbGJpQGtl
cm5lbC5vcmcACgkQzL64meEamQZjHRAA1lTH1Uv8wMoLpsefXYvc5w98kUu1CQGA
a23m14xNCv66pzgWTDKIk0zQpPiIpoWgvuwohVnDV0ygyCmEyg4Qp5Y6HQcFbDsY
JEQDK41TT9GIEza6b/rhBSzR90MXlXxAMnFRKnxlLgMw1na8Y6Jmn3c0MtQNCfZo
3roOhWnSittEbczNRzMVdZXV/CI8/CL6ykmnsjUipYrtQJHtdzx+M/BWxj/inoUP
Hl9hr6jH6zxQS+8UyoHSzNKtfWYvPMFUrwKNscsdAqjfpQyWV4uGoSFqGc+lGhXx
wrWdR+8WGchWNgJPlykAeaHVf4yyV/bOeQjpngC3HU2FQxc5Ohn3UVtfG7SOeMxD
ZNKZukZzRhZzXX8ha28nYu3r6++heKWS+rspOHwKR56HVhpQlSwvNwoqzTkPxxB5
p9ODyIfirsn2+Maj4weCpNARNxlc31rAybaQ8+uxAg8q6XcSD4lB5U929ajxpHQK
UErgDkIbjGpYY13Lrm7GjBuagiYyyvMKp3+6lR50tKlLYQSFB5EjTaYW15az2Yc+
xwTqSusxhP9MNMp3brU9ZJwzIA4s1gyjelbLsTYs/D3pgYA2YiYnajbwqmHJDINu
Nh+C6xyKiTC9OJspQv6+mHjMzc0VjBhr1KMPdRAdwLw1dHENyEhf6DrfHt/FjGxC
3fS6/uQ5jao=
=OiS0
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.8 merge window
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (99 commits)
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
usb: dwc3: gadget: Check for prepared TRBs
usb: gadget: Fix issue with config_ep_by_speed function
usb: cdns3: ep0: delete the redundant status stage
usb: dwc2: Update Core Reset programming flow.
usb: gadget: fsl: Fix a wrong judgment in fsl_udc_probe()
usb: gadget: fix potential double-free in m66592_probe.
usb: cdns3: Fix runtime PM imbalance on error
usb: gadget: lpc32xx_udc: don't dereference ep pointer before null check
usb: dwc3: Increase timeout for CmdAct cleared by device controller
USB: dummy-hcd: use configurable endpoint naming scheme
usb: cdns3: gadget: assign interrupt number to USB gadget structure
usb: gadget: core: sync interrupt before unbind the udc
arm64: dts: qcom: sc7180: Add interconnect properties for USB
arm64: dts: qcom: sdm845: Add interconnect properties for USB
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
ARM: dts: at91: Remove the USB EP child node
dt-bindings: usb: atmel: Mark EP child node as deprecated
...
This patch adds new config_ep_by_speed_and_alt function which
extends the config_ep_by_speed about alt parameter.
This additional parameter allows to find proper usb_ss_ep_comp_descriptor.
Problem has appeared during testing f_tcm (BOT/UAS) driver function.
f_tcm function for SS use array of headers for both BOT/UAS alternate
setting:
static struct usb_descriptor_header *uasp_ss_function_desc[] = {
(struct usb_descriptor_header *) &bot_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &bot_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &bot_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &uasp_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bi_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &uasp_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bo_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_status_desc,
(struct usb_descriptor_header *) &uasp_status_in_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_status_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_cmd_desc,
(struct usb_descriptor_header *) &uasp_cmd_comp_desc,
(struct usb_descriptor_header *) &uasp_cmd_pipe_desc,
NULL,
};
The first 5 descriptors are associated with BOT alternate setting,
and others are associated with UAS.
During handling UAS alternate setting f_tcm driver invokes
config_ep_by_speed and this function sets incorrect companion endpoint
descriptor in usb_ep object.
Instead setting ep->comp_desc to uasp_bi_ep_comp_desc function in this
case set ep->comp_desc to uasp_ss_bi_desc.
This is due to the fact that it searches endpoint based on endpoint
address:
for_each_ep_desc(speed_desc, d_spd) {
chosen_desc = (struct usb_endpoint_descriptor *)*d_spd;
if (chosen_desc->bEndpoitAddress == _ep->address)
goto ep_found;
}
And in result it uses the descriptor from BOT alternate setting
instead UAS.
Finally, it causes that controller driver during enabling endpoints
detect that just enabled endpoint for bot.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The threaded interrupt handler may still be called after the
usb_gadget_disconnect is called, it causes the structures used
at interrupt handler was freed before it uses, eg the
usb_request. This issue usually occurs we remove the udc function
during the transfer. Below is the example when doing stress
test for android switch function, the EP0's request is freed
by .unbind (configfs_composite_unbind -> composite_dev_cleanup),
but the threaded handler accesses this request during handling
setup packet request.
In fact, there is no protection between unbind the udc
and udc interrupt handling, so we have to avoid the interrupt
handler is occurred or scheduled during the .unbind flow.
init: Sending signal 9 to service 'adbd' (pid 18077) process group...
android_work: did not send uevent (0 0 000000007bec2039)
libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 6ms
init: Service 'adbd' (pid 18077) received signal 9
init: Sending signal 9 to service 'adbd' (pid 18077) process group...
libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:14)
init: Received control message 'start' for 'adbd' from pid: 399 (/vendor/bin/hw/android.hardware.usb@1.
init: starting service 'adbd'...
read descriptors
read strings
Unable to handle kernel read from unreadable memory at virtual address 000000000000002a
android_work: sent uevent USB_STATE=CONNECTED
Mem abort info:
ESR = 0x96000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=00000000e97f1000
using random self ethernet address
[000000000000002a] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 232 Comm: irq/68-5b110000 Not tainted 5.4.24-06075-g94a6b52b5815 #92
Hardware name: Freescale i.MX8QXP MEK (DT)
pstate: 00400085 (nzcv daIf +PAN -UAO)
using random host ethernet address
pc : composite_setup+0x5c/0x1730
lr : android_setup+0xc0/0x148
sp : ffff80001349bba0
x29: ffff80001349bba0 x28: ffff00083a50da00
x27: ffff8000124e6000 x26: ffff800010177950
x25: 0000000000000040 x24: ffff000834e18010
x23: 0000000000000000 x22: 0000000000000000
x21: ffff00083a50da00 x20: ffff00082e75ec40
x19: 0000000000000000 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000001
x11: ffff80001180fb58 x10: 0000000000000040
x9 : ffff8000120fc980 x8 : 0000000000000000
x7 : ffff00083f98df50 x6 : 0000000000000100
x5 : 00000307e8978431 x4 : ffff800011386788
x3 : 0000000000000000 x2 : ffff800012342000
x1 : 0000000000000000 x0 : ffff800010c6d3a0
Call trace:
composite_setup+0x5c/0x1730
android_setup+0xc0/0x148
cdns3_ep0_delegate_req+0x64/0x90
cdns3_check_ep0_interrupt_proceed+0x384/0x738
cdns3_device_thread_irq_handler+0x124/0x6e0
cdns3_thread_irq+0x94/0xa0
irq_thread_fn+0x30/0xa0
irq_thread+0x150/0x248
kthread+0xfc/0x128
ret_from_fork+0x10/0x18
Code: 910e8000 f9400693 12001ed7 79400f79 (3940aa61)
---[ end trace c685db37f8773fba ]---
Kernel panic - not syncing: Fatal exception
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0002,20002008
Memory Limit: none
Rebooting in 5 seconds..
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To take advantage of DWC3 internal TRB prefetch and cache for
performance, inform the controller the last request with stream_id
before switching to a different stream transfer. This allows the
controller to maintain its transfer burst within the stream ID.
Introduce the usb-request is_last field to help inform the DWC3
controller of this.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
usb_hcd_pci_probe expects users to call this with driver_data set as
hc_driver, that limits the possibility of using the driver_data for
driver data.
Add hc_driver as argument to usb_hcd_pci_probe and modify the callers
ehci/ohci/xhci/uhci to pass hc_driver as argument and freeup the
driver_data used
Tested xhci driver on Dragon-board RB3, compile tested ehci, ohci and
uhci.
[For all but the xHCI parts]
[For the xhci part]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-2-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some vendors glue layer need to handle some events for vbus, eg,
some i.mx platforms (imx7d, imx8mm, imx8mn, etc) needs vbus event
to handle charger detection, its charger detection is finished at
glue layer code, but not at USB PHY driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The USB LANGID validation code in "check_user_usb_string" function is
moved to "usb_validate_langid" function which can be used by other usb
gadget drivers.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In a quest to divide up the 5.7-rc1 merge chunks into reviewable pieces.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I2e5960415348c06e8f10e10cbefb3ee5c3745e73
This became again a busy development cycle. There are a few ALSA
core updates (merely API cleanups and sparse fixes), while majority
of other changes are found in ASoC scene.
Here are some highlights:
* ALSA core:
- More helper macros for sparse warning fixes (e.g. bitwise types)
- Slight optimization of PCM OSS locks
- Make common handling for PCM / compress buffers (for SOF)
* ASoC:
- Lots of code refactoring and modernization for (still ongoing)
componentization works
- Conversion of SND_SOC_ALL_CODECS to use imply
- Continued refactoring and fixing of the Intel SOF/SST support,
including the initial (but still incomplete) SoundWire support
- SoundWire and more advanced clocking support for Realtek RT5682
- Support for amlogic GX, Meson 8, Meson 8B and T9015 DAC, Broadcom
DSL/PON, Ingenic JZ4760 and JZ4770, Realtek RL6231, and TI TAS2563
and TLV320ADCX140
* HD-audio:
- Optimizations in HDMI jack handling
- A few new quirks and fixups for Realtek codecs
* USB-audio:
- Delayed registration support
- New quirks for Motu, Kingston, Presonus
-----BEGIN PGP SIGNATURE-----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=fAMQ
-----END PGP SIGNATURE-----
Merge tag 'sound-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became again a busy development cycle. There are few ALSA core
updates (merely API cleanups and sparse fixes), with the majority of
other changes are found in ASoC scene.
Here are some highlights:
ALSA core:
- More helper macros for sparse warning fixes (e.g. bitwise types)
- Slight optimization of PCM OSS locks
- Make common handling for PCM / compress buffers (for SOF)
ASoC:
- Lots of code refactoring and modernization for (still ongoing)
componentization works
- Conversion of SND_SOC_ALL_CODECS to use imply
- Continued refactoring and fixing of the Intel SOF/SST support,
including the initial (but still incomplete) SoundWire support
- SoundWire and more advanced clocking support for Realtek RT5682
- Support for amlogic GX, Meson 8, Meson 8B and T9015 DAC, Broadcom
DSL/PON, Ingenic JZ4760 and JZ4770, Realtek RL6231, and TI TAS2563
and TLV320ADCX140
HD-audio:
- Optimizations in HDMI jack handling
- A few new quirks and fixups for Realtek codecs
USB-audio:
- Delayed registration support
- New quirks for Motu, Kingston, Presonus"
* tag 'sound-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: usb-audio: Fix case when USB MIDI interface has more than one extra endpoint descriptor
Revert "ALSA: uapi: Drop asound.h inclusion from asoc.h"
ALSA: hda/realtek - Remove now-unnecessary XPS 13 headphone noise fixups
ALSA: hda/realtek - Set principled PC Beep configuration for ALC256
ALSA: doc: Document PC Beep Hidden Register on Realtek ALC256
ALSA: hda/realtek - a fake key event is triggered by running shutup
ALSA: hda: default enable CA0132 DSP support
ASoC: amd: acp3x-pcm-dma: clean up two indentation issues
ASoC: tlv320adcx140: Remove undocumented property
ASoC: Intel: sof_sdw: Add Volteer support with RT5682 SNDW helper function
ASoC: Intel: common: add match table for TGL RT5682 SoundWire driver
ASoC: Intel: boards: add sof_sdw machine driver
ASoC: Intel: soc-acpi: update topology and driver name for SoundWire platforms
ASoC: rt5682: move DAI clock registry to I2S mode
ASoC: pxa: magician: convert to use i2c_new_client_device()
ASoC: SOF: Intel: hda-ctrl: add reset cycle before parsing capabilities
Asoc: SOF: Intel: hda: check SoundWire wakeen interrupt in irq thread
ASoC: SOF: Intel: hda: add WAKEEN interrupt support for SoundWire
ASoC: SOF: Intel: hda: add parameter to control SoundWire clock stop quirks
ASoC: SOF: Intel: hda: merge IPC, stream and SoundWire interrupt handlers
...
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
In a quest to make the huge -rc1 merge easier to handle and bisect,
merge the first chunk of 5.7-rc1 patches into android-mainline.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Ib54436e9515660a4c0c25c49c21bfb399eb57921
This is a very big update for the core since Morimoto-san has been
rather busy continuing his refactorings to clean up a lot of the cruft
that we have accumilated over the years. We've also gained several new
drivers, including initial (but still not complete) parts of the Intel
SoundWire support.
- Lots of refactorings to modernize the code from Morimoto-san.
- Conversion of SND_SOC_ALL_CODECS to use imply from Geert Uytterhoeven.
- Continued refactoring and fixing of the Intel support.
- Soundwire and more advanced clocking support for Realtek RT5682.
- Support for amlogic GX, Meson 8, Meson 8B and T9015 DAC, Broadcom
DSL/PON, Ingenic JZ4760 and JZ4770, Realtek RL6231, and TI TAS2563 and
TLV320ADCX140.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl6B03sTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Jm5B/4pb6Hz1ifM+ikR4qB7BOdm/UGzxWlD
Mng+qN3kh6Tx+x8/xnQRmfOnhFoKnDSTnlxcDr6ujAtz3bH+CKXbo2jjfvmagQrW
j87tYGdh6T38E6mf6543Eth3zJGphZYUY70REXt0HsaQ8bA912nrs5H8LTFiD2i+
lBJd/MmlCYL3gb/ftN9dpTfYYdxLy9HH9j5tR5zpLN3AD3Hew9jHqqX+ioAk+6lA
Nisbx5grP10pWFklYXyJlUFQOqMOYMtPMblLRA9bjqcEtL3quIXPXKkPNtTh+0Kf
5t7Q39RtVXJAk0DcatjMJUGAGQyM9r5g1Nk8WLB1LLv+NfLcO6cUpLAc
=+z/q
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.7
This is a very big update for the core since Morimoto-san has been
rather busy continuing his refactorings to clean up a lot of the cruft
that we have accumilated over the years. We've also gained several new
drivers, including initial (but still not complete) parts of the Intel
SoundWire support.
- Lots of refactorings to modernize the code from Morimoto-san.
- Conversion of SND_SOC_ALL_CODECS to use imply from Geert Uytterhoeven.
- Continued refactoring and fixing of the Intel support.
- Soundwire and more advanced clocking support for Realtek RT5682.
- Support for amlogic GX, Meson 8, Meson 8B and T9015 DAC, Broadcom
DSL/PON, Ingenic JZ4760 and JZ4770, Realtek RL6231, and TI TAS2563 and
TLV320ADCX140.
The NCM specification defines two formats of transfer blocks: with 16-bit
fields (NTB-16) and with 32-bit fields (NTB-32). Currently only NTB-16 is
implemented.
This patch adds the support of NTB-32. The motivation behind this is that
some devices such as E5785 or E5885 from the current generation of Huawei
LTE routers do not support NTB-16. The previous generations of Huawei
devices are also use NTB-32 by default.
Also this patch enables NTB-32 by default for Huawei devices.
During the 2019 ValdikSS made five attempts to contact Huawei to add the
NTB-16 support to their router firmware, but they were unsuccessful.
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds separate header file for the Thunderbolt 3
Alternate Mode (aka. TBT). The header supplies definitions for
all the Thunderbolt specific VDOs (Vendor Defined Objects)
that are described in the USB Type-C Connector specification
v2.0, as well as definition for the Thunderbolt 3 Standard
ID (SID).
There is also a new connector state value for the
Thunderbolt 3 Alternate Mode that can be used with the mux
drivers.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-9-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch devices have been named by using the name of the
parent device as base for now, but if for example the
parent device controls multiple muxes, that will not work.
Adding an optional member "name" to the switch descriptor
that can be used for naming the switch during registration.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB role callback functions had a parameter pointing to
the parent device (struct device) of the switch. The
assumption was that the switch parent is always the
controller. Firstly, that may not be true in every case, and
secondly, it prevents us from supporting devices that supply
multiple muxes.
Changing the first parameter of usb_role_switch_set_t and
usb_role_switch_get_t from struct device to struct
usb_role_switch.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding usb_role_switch_get/set_drvdata() functions that the
switch drivers can use for setting and getting private data
pointer that is associated with the switch.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing fwnode_typec_switch_get() and
fwnode_typec_mux_get() functions that work just like
typec_switch_get() and typec_mux_get() but they take struct
fwnode_handle as the first parameter instead of struct
device.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding helpers typec_switch_set() and typec_mux_set() that
simply call the ->set callback function of the mux. These
functions make it possible to set the mux states also from
outside the class code.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mux devices have been named by using the name of the
parent device as base until now, but if for example the
parent device has multiple muxes that will not work. This
makes it possible to supply the name for a mux during
registration.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200220132017.GA29262@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UAC2 Effect Unit Descriptor has a slightly different definition
from other similar ones like Processing Unit or Extension Unit.
Define it here so that it can be used in USB-audio driver in a later
patch.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200213112059.18745-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using the generic notification chain is not reasonable with
the alternate modes because it would require dependencies
between the drivers of the components that need the
notifications, and the typec drivers.
There are no users for the alternate mode notifications, so
removing the chain and the API for it completely.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200211112531.86510-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since EHCI/OHCI controllers on R-Car Gen3 SoCs are possible to
be getting stuck very rarely after a full/low usb device was
disconnected. To detect/recover from such a situation, the controllers
require a special way which poll the EHCI PORTSC register and changes
the OHCI functional state.
So, this patch adds a polling timer into the ehci-platform driver,
and if the ehci driver detects the issue by the EHCI PORTSC register,
the ehci driver removes a companion device (= the OHCI controller)
to change the OHCI functional state to USB Reset once. And then,
the ehci driver adds the companion device again.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1580114262-25029-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new device quirk that can be used to blacklist endpoints.
Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.
In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.
Tested-by: edes <edes@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Baby steps in the 5.6-rc1 merge cycle to make things easier to review
and debug.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I2d3a69b5256f71ae18b500b0ef145f93e4255dbc
Baby steps in the 5.6-rc1 merge cycle to make things easier to review
and debug.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I4c44b3c32065ea0ed8175b31665f2a4195a27300
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
- a missing ir-usb endpoint sanity check
- fixes for two long-standing regressions in ir-usb
- opticon chars_in_buffer support
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXi6evgAKCRALxc3C7H1l
CJs8AP4ubaKYyH5cLMthwhLAdGqp2UdfVqdUu25Kb2bnyXbStAEAsvhOHWbdrQKn
cRLLJqYO4M3nPH2YF1Is4qSJZmUxXQk=
=Aof1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.6-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
Here are the USB-serial updates for 5.6-rc1, including:
- a missing ir-usb endpoint sanity check
- fixes for two long-standing regressions in ir-usb
- opticon chars_in_buffer support
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.6-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
USB: serial: garmin_gps: Use flexible-array member
USB: serial: opticon: stop all I/O on close()
USB: serial: opticon: add chars_in_buffer() implementation
Instead of using the legacy GPIO API and keeping track on
polarity inversion semantics in the driver, switch to use
GPIO descriptors for this driver and change all consumers
in the process.
This makes it possible to retire platform data completely:
the only remaining platform data member was "wakeup" which
was intended to make the vbus interrupt wakeup capable,
but was not set by any users and thus remained unused. VBUS
was not waking any devices up. Leave a comment about it so
later developers using the platform can consider setting it
to always enabled so plugging in USB wakes up the platform.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Sylwester Nawrocki <snawrocki@kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200123155013.93249-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0d795e4f3 ("usb: irda: cleanup on ir-usb module") added a USB
IrDA header with common defines, but mistakingly switched to using the
class-descriptor baud-rate bitmask values for the outbound header.
This broke link-speed handling for rates above 9600 baud, but a device
would also be able to operate at the default 9600 baud until a
link-speed request was issued (e.g. using the TCGETS ioctl).
Fixes: e0d795e4f3 ("usb: irda: cleanup on ir-usb module")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Cc: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The last user of the phy generic platform data was
deleted in commit 1e041b6f31
("usb: dwc3: exynos: Remove dead code"). So get rid of
the platform data, which rids us of another consumer of
the legacy GPIO API at the same time. Make sure we
only inlcude <linux/gpio/consumer.h> which is all we use.
Alter the usb_phy_gen_create_phy() function prototype to
not pass any platform data as this is just hardcoded to
NULL at all locations calling it in the kernel.
Move the devm_gpiod_get* calls out of the if (of_node)
parenthesis, as these calls are generic and do not depend
on device tree, they are used by any hardware description.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is much more intuitive if reset is treated as asserted when GPIO value
is set to 1. All NVIDIA Tegra device-trees are properly specifying active
state of the reset-GPIO since 2013, let's clean up that part of the code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-14-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now drivers (like NVIDIA Tegra USB PHY for example) will be able to
benefit from the resource-managed variant, making driver's code a bit
cleaner.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-11-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY driver should keep track of the enable state, otherwise enable
refcount is screwed if USB driver tries to enable PHY when it is already
enabled. This will be the case for ChipIdea and Tegra EHCI drivers once
PHY driver will gain support for the init/shutdown callbacks.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-5-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defining the USB modes from the latest USB Power Delivery
Specification - USB 2.0, USB 3.2 and USB4 - as special modal
states just like the Accessory Modes.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-14-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing all the details that the alternate mode drivers
provide to the mux drivers during mode changes.
The mux drivers will in practice need to be able to make
decisions on their own. It is not enough that they get only
the requested port state. With the Thunderbolt 3 alternate
mode for example the mux driver will need to consider also
the capabilities of the cable before configuring the mux.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-13-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Discover Identity command response has also 3 product type
specific VDOs on top of ID Header VDO, Cert Stat VDO and
Product VDO.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-11-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The latest version of the USB Power Delivery Specification
R3.0 added UFP and DFP product types for the Discover
Identity message. Both types can be used for example for
checking the USB capability of the partner, which means the
USB modes (USB 2.0, USB 3.0 and USB4) that the partner
device supports.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-10-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Version 2.0 of the USB Power Delivery Specification R3.0
defines a new message called Enter_USB, which is made with
USB4 in mind. Enter_USB message is in practice the same as
the Enter Mode command (used when entering alternate modes)
that just needs to be used when entering USB4 mode.
The message does also support entering USB 2.0 or USB 3.2
mode instead of USB4 mode, but it is only required with
USB4. I.e. with USB2 and USB3 Enter_USB message is optional.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-9-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt 3, and probable USB4 too, will need to be able
to get details about the cables. Adding typec_cable_get()
function that the alternate mode drivers can use to gain
access to gain access to the cable.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas USBHS driver includes a bit of surplus headers
and uses the old GPIO API so let's switch it to use the
GPIO descriptor.
I noticed that the enable_gpio inside renesas_usbhs_driver_param
isn't really referenced anywhere, and it is also the wrong
type (u32) so let's just delete it and use a local variable
instead.
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191217141241.57639-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All configuration can and should be done through fwnodes instead of
through the tcpc_config struct and there are no existing users left of
struct tcpc_config, so lets remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191114111840.40876-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing struct typec_operations which has the same
callbacks as struct typec_capability. The old callbacks are
kept for now, but after all users have been converted, they
will be removed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leaving the private driver_data pointer of the port device
to the port drivers.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple wrapper function that searches USB role switches with
class_find_device_by_fwnode().
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191008122600.22340-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This merges Linus's tree as of commit b41dae061b ("Merge tag
'xfs-5.4-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux")
into android-mainline.
This "early" merge makes it easier to test and handle merge conflicts
instead of having to wait until the "end" of the merge window and handle
all 10000+ commits at once.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I6bebf55e5e2353f814e3c87f5033607b1ae5d812
Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the staging
directory, uwb and wusb (wireless USB support), because there are no
devices that actually use this protocol anymore, and what we have today
probably doesn't work at all given that the maintainers left many many
years ago. So move it to staging where it will be removed in a few
releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups due
to the driver core changes to support that. Nothing really major, just
constant forward progress.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIYYQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymn8ACfTi8Y2ku/yqw8Nvs4vQjc08MUDhgAoNnbhsI6
H3HUrZTjJJzuxHCM22Lh
=8ZRm
-----END PGP SIGNATURE-----
Merge tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the
staging directory, uwb and wusb (wireless USB support), because there
are no devices that actually use this protocol anymore, and what we
have today probably doesn't work at all given that the maintainers
left many many years ago. So move it to staging where it will be
removed in a few releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups
due to the driver core changes to support that. Nothing really major,
just constant forward progress.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: usbcore: Fix slab-out-of-bounds bug during device reset
usb: cdns3: Remove redundant dev_err call in cdns3_probe()
USB: rio500: Fix lockdep violation
USB: rio500: simplify locking
usb: mtu3: register a USB Role Switch for dual role mode
usb: common: add USB GPIO based connection detection driver
usb: common: create Kconfig file
usb: roles: get usb-role-switch from parent
usb: roles: Add fwnode_usb_role_switch_get() function
device connection: Add fwnode_connection_find_match()
usb: roles: Introduce stubs for the exiting functions in role.h
dt-bindings: usb: mtu3: add properties about USB Role Switch
dt-bindings: usb: add binding for USB GPIO based connection detection driver
dt-bindings: connector: add optional properties for Type-B
dt-binding: usb: add usb-role-switch property
usbip: Implement SG support to vhci-hcd and stub driver
usb: roles: intel: Enable static DRD mode for role switch
xhci-ext-caps.c: Add property to disable Intel SW switch
usb: dwc3: remove generic PHY calibrate() calls
usb: core: phy: add support for PHY calibration
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJdf6RZAAoJEJpsee/mABjZDO0QAKGkhoEdUmrar0Yf7/ibTrLK
0naWvQtPEm6dv+u1zNfe2IWchVRbBVm+YSLbyaAZwJQknV5gdxgd/UyQrSG9yywg
xDEUdnj03AksYreWbr1tfcA6kQQJEeqZeysNej0v7MAd6MFz5O4M4CgYfAnCLCc4
5rzSqbtFgv4uNMnMTJGKk8anFWNYLbewoBGVcGIEQ/KQlf1+NrlqBWk7CgvencaF
VLqpK0mllhKxAOJHGz6Q/XXiJnj0u56X9GvfcJoaxDWVrAnC6ii29NOHKeXhxS5W
/EmhIEuqCRoGLAMYmml+NbCv43Z1L7neDJwg6sf9cVqNrB9L1Ldlgpr/uoj++Z+l
wdZ297Ogs4mKYx5CCdK4X1TaFOH3s+/awFr1uEP70p+QsPDMrCTuLSjgeQziylgO
kBGIGkqG4l48V9psQy/9SaalgGSB8w6Ta/ms1+rWc99Qj3ExDFCAMIl4uzOxjxT1
9MZbvhc3ulLT4BBXNGhvNaPJxYGk+ggV/ObsqF9+GkxLcVPR8L1tPIzZMB5dB1YR
0YcwyK2jlZGKIwMjLYDT+axGGPh9G+LV6INjRbW5BGJHgNZF844Bxw/eFYushLAu
KHrbpm3ImzJw9eHlgIRtFRTy8ZKPuvv7fGg3zzKSHT4ZmC3tEM68PnQGuMEvVX8Q
+Oa6OiDb0pkV1zsACSZn
=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
The fwnode_usb_role_switch_get() function is exactly the
same as usb_role_switch_get(), except that it takes struct
fwnode_handle as parameter instead of struct device.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Biju Das <biju.das@bp.renesas.com>
Link: https://lore.kernel.org/r/1567070558-29417-8-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds stubs for the exiting functions while
CONFIG_USB_ROLE_SWITCH does not enabled.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1567070558-29417-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=KUJN
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: Changes for v5.4 merge window
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (45 commits)
usb: gadget: net2280: Add workaround for AB chip Errata 11
usb: gadget: net2280: Move all "ll" registers in one structure
usb: dwc3: gadget: Workaround Mirosoft's BESL check
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb: cdns3: Add Cadence USB3 DRD Driver
usb: common: Simplify usb_decode_get_set_descriptor function.
usb: common: Patch simplify usb_decode_set_clear_feature function.
usb: common: Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: gadget: composite: Set recommended BESL values
usb: dwc3: gadget: Set BESL config parameter
usb: dwc3: Separate field holding multiple properties
usb: gadget: Export recommended BESL values
usb: phy: phy-fsl-usb: Make structure fsl_otg_initdata constant
usb: udc: lpc32xx: silence fall-through warning
usb: dwc3: meson-g12a: fix suspend resume regulator unbalanced disables
usb: udc: lpc32xx: remove set but not used 3 variables
usb: gadget: udc: core: Fix segfault if udc_bind_to_driver() for pending driver fails
usb: dwc3: st: Add of_dev_put() in probe function
usb: dwc3: st: Add of_node_put() before return in probe function
...
The split into multiple structures of the "ll" register bank is
impractical. It makes it hard to add ll_lfps_timers_2 which is
at offset 0x794, which is outside of the existing "lfps" structure
and would require us to add yet another one.
Instead, move all the "ll" registers into a single usb338x_ll_regs
structure, and add ll_lfps_timers_2 while at it. It will be used
in a subsequent patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/common/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/ch9.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently there's no option for the controller driver to report the
recommended Best Effort Service Latency (BESL) when operating with LPM
support. Add new fields in usb_dcd_config_params to export the
recommended baseline and deep BESL values for the function drivers to
set the proper BESL value in the BOS descriptor.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is only used by arch/arm/mach-s3c64xx/setup-usb-phy.c
$ git grep samsung_usb_phy_type
include/linux/usb/samsung_usb_phy.h:enum samsung_usb_phy_type {
$ git grep USB_PHY_TYPE_DEVICE
arch/arm/mach-s3c64xx/setup-usb-phy.c: if (type == USB_PHY_TYPE_DEVICE)
arch/arm/mach-s3c64xx/setup-usb-phy.c: if (type == USB_PHY_TYPE_DEVICE)
include/linux/usb/samsung_usb_phy.h: USB_PHY_TYPE_DEVICE,
$ git grep USB_PHY_TYPE_HOST
include/linux/usb/samsung_usb_phy.h: USB_PHY_TYPE_HOST,
Actually, 'enum samsung_usb_phy_type' is unused; the 'type' parameter
has 'int' type. Anyway, there is no need to declare this enum in the
globally visible header. Squash the header.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The usb core is the only major place in the kernel that checks for
a non-NULL device dma_mask to see if a device is DMA capable. This
is generally a bad idea, as all major busses always set up a DMA mask,
even if the device is not DMA capable - in fact bus layers like PCI
can't even know if a device is DMA capable at enumeration time. This
leads to lots of workaround in HCD drivers, and also prevented us from
setting up a DMA mask for platform devices by default last time we
tried.
Replace this guess with an explicit HCD_DMA that is set by drivers that
appear to have DMA support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190816062435.881-4-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB buffer allocation code is the only place in the usb core (and in
fact the whole kernel) that uses is_device_dma_capable, while the URB
mapping code uses the uses_dma flag in struct usb_bus. Switch the buffer
allocation to use the uses_dma flag used by the rest of the USB code,
and create a helper in hcd.h that checks this flag as well as the
CONFIG_HAS_DMA to simplify the caller a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190811080520.21712-3-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UWB and wusbcore code is long obsolete, so let us just move the code
out of the real part of the kernel and into the drivers/staging/
location with plans to remove it entirely in a few releases.
Link: https://lore.kernel.org/r/20190806101509.GA11280@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- move the USB special case that bounced DMA through a device
bar into the USB code instead of handling it in the common
DMA code (Laurentiu Tudor and Fredrik Noring)
- don't dip into the global CMA pool for single page allocations
(Nicolin Chen)
- fix a crash when allocating memory for the atomic pool failed
during boot (Florian Fainelli)
- move support for MIPS-style uncached segments to the common
code and use that for MIPS and nios2 (me)
- make support for DMA_ATTR_NON_CONSISTENT and
DMA_ATTR_NO_KERNEL_MAPPING generic (me)
- convert nds32 to the generic remapping allocator (me)
-----BEGIN PGP SIGNATURE-----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=01Fr
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.3' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- move the USB special case that bounced DMA through a device bar into
the USB code instead of handling it in the common DMA code (Laurentiu
Tudor and Fredrik Noring)
- don't dip into the global CMA pool for single page allocations
(Nicolin Chen)
- fix a crash when allocating memory for the atomic pool failed during
boot (Florian Fainelli)
- move support for MIPS-style uncached segments to the common code and
use that for MIPS and nios2 (me)
- make support for DMA_ATTR_NON_CONSISTENT and
DMA_ATTR_NO_KERNEL_MAPPING generic (me)
- convert nds32 to the generic remapping allocator (me)
* tag 'dma-mapping-5.3' of git://git.infradead.org/users/hch/dma-mapping: (29 commits)
dma-mapping: mark dma_alloc_need_uncached as __always_inline
MIPS: only select ARCH_HAS_UNCACHED_SEGMENT for non-coherent platforms
usb: host: Fix excessive alignment restriction for local memory allocations
lib/genalloc.c: Add algorithm, align and zeroed family of DMA allocators
nios2: use the generic uncached segment support in dma-direct
nds32: use the generic remapping allocator for coherent DMA allocations
arc: use the generic remapping allocator for coherent DMA allocations
dma-direct: handle DMA_ATTR_NO_KERNEL_MAPPING in common code
dma-direct: handle DMA_ATTR_NON_CONSISTENT in common code
dma-mapping: add a dma_alloc_need_uncached helper
openrisc: remove the partial DMA_ATTR_NON_CONSISTENT support
arc: remove the partial DMA_ATTR_NON_CONSISTENT support
arm-nommu: remove the partial DMA_ATTR_NON_CONSISTENT support
ARM: dma-mapping: allow larger DMA mask than supported
dma-mapping: truncate dma masks to what dma_addr_t can hold
iommu/dma: Apply dma_{alloc,free}_contiguous functions
dma-remap: Avoid de-referencing NULL atomic_pool
MIPS: use the generic uncached segment support in dma-direct
dma-direct: provide generic support for uncached kernel segments
au1100fb: fix DMA API abuse
...
Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while with
no reported issues. Nothing is earth-shattering, just constant forward
progress for more devices supported and cleanups and small fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed in.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSXjYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynMYACgnSRP3GylwMywrkc9paVmDeiIgNwAn0N2sika
JEW7C3lkBJZJ7R6V/Ynm
=drla
-----END PGP SIGNATURE-----
Merge tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while
with no reported issues. Nothing is earth-shattering, just constant
forward progress for more devices supported and cleanups and small
fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed
in"
* tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
Revert "usb: gadget: storage: Remove warning message"
Revert "dt-bindings: add binding for USBSS-DRD controller."
Revert "usb:gadget Separated decoding functions from dwc3 driver."
Revert "usb:gadget Patch simplify usb_decode_set_clear_feature function."
Revert "usb:gadget Simplify usb_decode_get_set_descriptor function."
Revert "usb:cdns3 Add Cadence USB3 DRD Driver"
Revert "usb:cdns3 Fix for stuck packets in on-chip OUT buffer."
usb :fsl: Change string format for errata property
usb: host: Stops USB controller init if PLL fails to lock
usb: linux/fsl_device: Add platform member has_fsl_erratum_a006918
usb: phy: Workaround for USB erratum-A005728
usb: fsl: Set USB_EN bit to select ULPI phy
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
drivers/usb/typec/tps6598x.c: fix 4CC cmd write
drivers/usb/typec/tps6598x.c: fix portinfo width
usb: storage: scsiglue: Do not skip VPD if try_vpd_pages is set
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
...
- Some tiny improvements, no function change.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJdHrMsAAoJEEhZKYFQ1nG7jE0IAJXwiUh8Dd3IUkik8Nft3jGw
wPkiYfs9LGyQ6sJ8l4TxrbVvsnEs0n9dsExXP03MK6ow6Mqen5lHsa0VHkPeZX4C
+NyviJEH3BiY7jcWvhj8Sdp2/DBfulWPMTGZLncyNdinWGTrNQKzcDd7jzvp4Y1x
ZZSly0E0m5uU7ZP1QOw+/142+Mi+ia9bKl+xqkeKTwsaykYaYstfuVrpabFJ50FL
k8K1q0DCnF6G7aCGTBuVm0coe68TUcWIgl94BoZK6cSxEA4mJRU/VITYbR44dkBN
wHBJKIZzie4jAKLVXuRWix1eMiIDkeS9qKRGnc72hrF3eADlaikk9fwWLOQFjLk=
=hzIY
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
- Add imx7ulp support.
- Some tiny improvements, no function change.
* tag 'usb-ci-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: msm: Use devm_platform_ioremap_resource()
usb: chipidea: imx: Use devm_platform_ioremap_resource()
usb: chipidea: Use dev_err() instead of pr_err()
usb: chipidea: imx: "fsl,usbphy" phandle is not mandatory now
usb: chipidea: imx: add imx7ulp support
Turns out a few more important changes came about. We have the new
Cadence DRD Driver being added here and that's the biggest, most
important part.
Together with that we have suport for new imx7ulp phy. Support for
TigerLake Devices on dwc3. Also a couple important fixes which weren't
completed in time for the -rc cycle.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=ciUl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: more changes for v5.3 merge window
Turns out a few more important changes came about. We have the new
Cadence DRD Driver being added here and that's the biggest, most
important part.
Together with that we have suport for new imx7ulp phy. Support for
TigerLake Devices on dwc3. Also a couple important fixes which weren't
completed in time for the -rc cycle.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
usb: phy: phy-mxs-usb: add imx7ulp support
doc: dt-binding: mxs-usb-phy: add compatible for 7ulp
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb:cdns3 Add Cadence USB3 DRD Driver
usb:gadget Simplify usb_decode_get_set_descriptor function.
usb:gadget Patch simplify usb_decode_set_clear_feature function.
usb:gadget Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: dwc3: pci: add support for TigerLake Devices
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/gadget/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/gadget.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
-----BEGIN PGP SIGNATURE-----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=3HLl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v5.3 merge window
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
* tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (30 commits)
usb: dwc3: remove unused @lock member of dwc3_ep struct
usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices
usb: Replace snprintf with scnprintf in gether_get_ifname
usb: gadget: ether: Fix race between gether_disconnect and rx_submit
usb: gadget: storage: Remove warning message
usb: dwc3: gadget: Add support for disabling U1 and U2 entries
usb: gadget: send usb_gadget as an argument in get_config_params
doc: dt: bindings: usb: dwc3: Update entries for disabling U1 and U2
usb: dwc3: qcom: Use of_clk_get_parent_count()
usb: dwc3: Fix core validation in probe, move after clocks are enabled
usb: dwc3: qcom: Improve error handling
usb: dwc3: qcom: Start USB in 'host mode' on the SDM845
usb: dwc3: qcom: Add support for booting with ACPI
soc: qcom: geni: Add support for ACPI
Revert "usb: dwc2: host: Setting qtd to NULL after freeing it"
usb: gadget: net2272: remove redundant assignments to pointer 's'
usb: gadget: Zero ffs_io_data
USB: omap_udc: Remove unneeded variable
fotg210-udc: Remove unneeded variable
usb: gadget: at91_udc: Remove unneeded variable
...
In the future, each struct renesas_usbhs_driver_param is stored on
the each platform related source code (e.g. rcar3.c). So, to simplify
the source code, this patch adds a new flag has_new_pipe_configs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now no one uses the type member so that this patch removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To remove the type of renesas_usbhs_driver_param in the future, this
patch uses a specific flag "multi_clks".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notify_hotplug callback was supported in v3.10, but the last user
(armadillo800eva) was removed by the commit 1fa59bda21 ("ARM: shmobile:
Remove legacy board code for Armadillo-800 EVA"). So, this patch
removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing struct usb_gadget * as an extra argument in get_config_params
makes gadget drivers to easily update the U1DevExitLat & U2DevExitLat
values based on the values passed from the device tree. This patch
does the same
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In this commit, we add CI_HDRC_PMQOS to avoid system entering idle,
at imx7ulp, if the system enters idle, the DMA will stop, so the USB
transfer can't work at this case.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Controlling PWMEN/EXTLP (named as "has_otg") was supported in v3.2,
but the last user (kzm9g) was removed by the commit 30f8925a57
("ARM: shmobile: Remove legacy board code for KZM-A9-GT"). So, this
patch remove it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SUDMAC feature was supported in v3.10, but was never used by
any platform. So, this patch removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the addition of the local memory allocator, the HCD_LOCAL_MEM
flag can be dropped and the checks against it replaced with a check
for the localmem_pool ptr being initialized.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Fredrik Noring <noring@nocrew.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For HCs that have local memory, replace the current DMA API usage with
a genalloc generic allocator to manage the mappings for these devices.
To help users, introduce a new HCD API, usb_hcd_setup_local_mem() that
will setup up the genalloc backing up the device local memory. It will
be used in subsequent patches. This is in preparation for dropping
the existing "coherent" dma mem declaration APIs. The current
implementation was relying on a short circuit in the DMA API that in
the end, was acting as an allocator for these type of devices.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Fredrik Noring <noring@nocrew.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Registering real device entries (struct device) for the mode
muxes as well as for the orientation switches.
The Type-C mux code was deliberately attempting to avoid
creation of separate device entries for the orientation
switch and the mode switch (alternate modes) because they
are not physical devices. They are functions of a single
physical multiplexer/demultiplexer switch device.
Unfortunately because of the dependency we still have on the
underlying mux device driver, we had to put in hacks like
the one in the commit 3e3b81965c ("usb: typec: mux: Take
care of driver module reference counting") to make sure the
driver does not disappear from underneath us. Even with
those hacks we were still left with a potential NUll pointer
dereference scenario, so just creating the device entries,
and letting the core take care of the dependencies. No more
hacks needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/A2 is similar to the R-Car Gen3 with some small differences.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC have a CFIFO register that is byte addressable. This means
when the CFIFO access is set to 32-bit, you can write 8-bit values to
addresses CFIFO+0, CFIFO+1, CFIFO+2, CFIFO+3.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some SoC, CNEN must be set for USB Device mode operation.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move options from 'flags' field in private structure to param structure
where other options are already being kept.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB accessory mode allows users to connect USB host hardware
specifically designed for Android-powered devices. The accessories
must adhere to the Android accessory protocol outlined in the
http://accessories.android.com documentation. This allows
Android devices that cannot act as a USB host to still interact with
USB hardware. When an Android device is in USB accessory mode, the
attached Android USB accessory acts as the host, provides power
to the USB bus, and enumerates connected devices.
Bug: 63740241
Bug: 120441124
Change-Id: I67964b50d278f3c0471d47efbb7b0973a3502681
[badhri: f_accessory is being migrated to userspace.]
Signed-off-by: Mike Lockwood <lockwood@android.com>
[AmitP: Folded following android-4.9 commit changes into this patch
ceb2f0aac624 ("ANDROID: usb: gadget: accessory: Fix section mismatch")
Parts of e27543931009 ("ANDROID: usb: gadget: Fixes and hacks to make android usb gadget compile on 3.8")
1b07ec751563 ("ANDROID: drivers: usb: gadget: 64-bit related type fixes")]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
[astrachan: Folded the following changes into this patch:
9d5891d516e2 ("ANDROID: usb: gadget: f_accessory: Add ACCESSORY_SET_AUDIO_MODE control request and ioctl")
dc66cfce9622 ("ANDROID: usb: gadget: f_accessory: Add support for HID input devices")
5f1ac9c2871b ("ANDROID: usb: gadget: f_accessory: move userspace interface to uapi")
9a6241722cd8 ("ANDROID: usb: gadget: f_accessory: Enabled Zero Length Packet (ZLP) for acc_write")
31a0ecd5a825 ("ANDROID: usb: gadget: f_accessory: check for accessory device before disconnecting HIDs")
580721fa6cbc ("ANDROID: usb: gadget: f_accessory: Migrate to USB_FUNCTION API")
7f407172fb28 ("ANDROID: usb: gadget: f_accessory: Fix for UsbAccessory clean unbind.")
ebc98ac5a22f ("ANDROID: usb: gadget: f_accessory: fix false disconnect due to a signal sent to the reading process")
71c6dc5ffdab ("ANDROID: usb: gadget: f_accessory: assign no-op request complete callbacks")
675047ee68e9 ("ANDROID: usb: gadget: f_accessory: Move gadget functions code")
b2bedaa5c7df ("CHROMIUM: usb: gadget: f_accessory: add .raw_request callback")]
Signed-off-by: Alistair Strachan <astrachan@google.com>
Add a pointer to the usb_function inside the
usb_function_instance structure to service
functions specific setup requests even before
the function gets added to the usb_gadget
Bug: 63740241
Bug: 68755607
Bug: 78114713
Bug: 120441124
Change-Id: I6f457006f6c5516cc6986ec2acdf5b1ecf259d0c
[badhri: This is a supporting patch for other patches which have
replacements pipelined. It can be dropped when those
implementations land.]
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
With a total of 50 non-merge commits, this is not a large pull
request. Most of the changes are, again, in dwc2 (37%) and dwc3 (32%)
with the rest of it scattered among other UDCs, function drivers and
device-tree bindings.
No really big feature this time around apart from support to Amlogic
being added to both dwc3 and dwc2 drivers.
-----BEGIN PGP SIGNATURE-----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=k1p8
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.2 merge window
With a total of 50 non-merge commits, this is not a large pull
request. Most of the changes are, again, in dwc2 (37%) and dwc3 (32%)
with the rest of it scattered among other UDCs, function drivers and
device-tree bindings.
No really big feature this time around apart from support to Amlogic
being added to both dwc3 and dwc2 drivers.
* tag 'usb-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (50 commits)
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
usb: dwc3: Free resource immediately after use
usb: dwc3: of-simple: Convert to bulk clk API
usb: dwc2: Delayed status support
usb: gadget: udc: lpc32xx: rework interrupt handling
...
Here are the USB-serial updates for 5.2-rc1, including:
- flow-control related fixes for pl2303
- fix for an initial-termios issue
- fix for a couple of unthrottle() races
- fix for f81232 interrupt-handling issues
- improved f81232 overrun handling
- support for higher f81232 line speeds
- support for f81232 break control
Included are also various clean ups.
All but the last four commits have been in linux-next and with no
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXMxfIgAKCRALxc3C7H1l
CMtcAP9uZf9T10gph5fEFVmMeL5TbXF/jdi0ovK6Yl2hwlcJvwEAi/iL8pjNEmdk
Bjy9ocYKsGixXqKi9b5+OEB39QFsZwI=
=LovK
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.2-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.2-rc1
Here are the USB-serial updates for 5.2-rc1, including:
- flow-control related fixes for pl2303
- fix for an initial-termios issue
- fix for a couple of unthrottle() races
- fix for f81232 interrupt-handling issues
- improved f81232 overrun handling
- support for higher f81232 line speeds
- support for f81232 break control
Included are also various clean ups.
All but the last four commits have been in linux-next and with no
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.2-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (22 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
USB: serial: io_edgeport: fix up switch fall-through comments
USB: serial: drop unused iflag macro
USB: serial: drop unnecessary goto
USB: serial: clean up throttle handling
USB: serial: fix unthrottle races
USB: serial: spcp8x5: simplify init_termios
USB: serial: oti6858: simplify init_termios
USB: serial: iuu_phoenix: simplify init_termios
USB: serial: iuu_phoenix: drop bogus initial cflag
USB: serial: cypress_m8: clean up initial-termios handling
USB: serial: cypress_m8: drop unused termios
USB: serial: cypress_m8: drop unused driver data flag
USB: serial: ark3116: drop redundant init_termios
USB: serial: fix initial-termios handling
USB: serial: digi_acceleport: clean up set_termios
USB: serial: digi_acceleport: clean up modem-control handling
...
In some places, the code prints a human-readable USB endpoint
transfer type (e.g. "bulk"). This involves a switch statement
sometimes wrapped around in ({ ... }) block leading to code
repetition.
To make this scenario easier, here introduces usb_ep_type_string()
function, which returns a human-readable name of provided
endpoint type.
It also changes a few places switch was used to use this
new function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In (e583d9d USB: global suspend and remote wakeup don't mix) we
introduced wakeup_enabled_descendants() as a static function. We'd
like to use this function in USB controller drivers to know if we
should keep the controller on during suspend time, since doing so has
a power impact.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Drop the RELEVANT_IFLAG() macro which essentially hasn't been used for
over a decade except in some remnant debug printks that were recently
removed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the throttle implementation by dropping the redundant
throttle_req flag which was a remnant from back when there was only a
single read URB.
Also convert the throttled flag to an atomic bit flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
This change will send an OFFLINE event to udev with the ERROR=DEAD
environment variable set when the HC dies.
By notifying user space the appropriate policies can be applied.
i.e.,
* Collect error logs.
* Notify the user that USB is no longer functional.
* Perform a graceful reboot.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Latest NVIDIA GPUs support VirtualLink device. Since USBIF
has not assigned a Standard ID (SID) for VirtualLink
so using NVIDA VID 0x955 as SVID.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.
For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.
This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.
The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.
To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.
Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some places, the code prints a human-readable USB endpoint
transfer type (e.g. "bulk"). This involves a switch statement
sometimes wrapped around in ({ ... }) block leading to code
repetition.
To make this scenario easier, here introduces usb_ep_type_string()
function, which returns a human-readable name of provided
endpoint type.
It also changes a few places switch was used to use this
new function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This static inline is unnecessary and can be removed
by using the vsprintf %ph extension.
This reduces overall object size by more than 2K.
Reported-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Chrome OS we want to use USBguard to potentially limit access to USB
devices based on policy. We however to do not want to wait for userspace to
come up before initializing fixed USB devices to not regress our boot
times.
This patch adds option to instruct the kernel to only authorize devices
connected to the internal ports. Previously we could either authorize
all or none (or, by default, we'd only authorize wired devices).
The behavior is controlled via usbcore.authorized_default command line
option.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Tested-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since with accessory modes there is no need for additional
identification when requesting a handle to the mux, we can
replace the second parameter that is passed to the
typec_mux_get() function with a pointer to alternate mode
description structure, and simply passing NULL with
accessory modes.
This change means the naming of the mux device connections
can be updated. Alternate and Accessory Modes will both be
handled with muxes named "mode-switch", and the orientation
switches will be named "orientation-switch".
Future identification of the alternate modes will be later
done using device property "svid" of the mux.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_update_source_capabilities() and tcpm_update_sink_capabilities()
are not used anywhere, and I don't recall why I introduced those functions
in the first place. Effectively that means that we don't know if they even
work, or ever did. Lets remove them.
Reported-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helpers used for reading and writing the pin assignment
from and to the Configuration VDO will be useful in GPU
drivers, and also UCSI driver after DisplayPort alt mode
support is added to it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add the HSIC support for imx
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJcF1bIExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbv1
Xgf/RIlKRdLOiO0wCJWkmiHRIU/YE0V6QNwhMKCUK2PfAqLI3px/a/uOam7U8ysn
6TvrUYxy/V7yBDCw6bR8bbJeP5gFjZPEnqd4RV6YZzP7Zc6FJ/10cLMWWGfB61JV
xqcVzJGjZ/AuU00TDDEeKXnGB4w6iH47x0ywimxlHSEhSUGQEoogopgtlr8JfnWg
bVQ9wr1jkUmkDymVFaHzrYSWVIToejGOB2kNRmhGpxKIUq3Mv/X0Vux50+egNpDK
ikyVo5oIr1cU0nVlAl2lquoTf6F7gRo2GduY9stw2VR6VxUUvd2cj57bJlhiwqPe
3jRiXjWtZKsWEcSpMhaT8ks+Og==
=Q7/x
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Improve the over-current handling for imx
- Add the HSIC support for imx
* tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: allow to configure oc polarity on i.MX25
usb: chipidea: imx: Warn if oc polarity isn't specified
usb: chipidea: imx: support configuring for active low oc signal
doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groups
usb: chipidea: host: override ehci->hub_control
usb: chipidea: imx: add HSIC support
usb: chipidea: add flag for imx hsic implementation
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
-----BEGIN PGP SIGNATURE-----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=n8VS
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB changes for v4.21
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
usb: dwc2: Fix disable all EP's on disconnect
usb: dwc3: gadget: Disable CSP for stream OUT ep
usb: dwc2: disable power_down on Amlogic devices
Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
usb: dwc3: trace: add missing break statement to make compiler happy
usb: dwc3: gadget: Report isoc transfer frame number
usb: gadget: Introduce frame_number to usb_request
usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
usb: renesas_usbhs: Remove dummy runtime PM callbacks
usb: dwc2: host: use hrtimer for NAK retries
usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
usb: mtu3: enable SETUPENDISR interrupt
usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
usb: mtu3: enable hardware remote wakeup from L1 automatically
usb: mtu3: remove QMU checksum
usb/mtu3: power down device ip at setup
usb: dwc2: Disable power down feature on Samsung SoCs
usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
...
NXP (Freecale) imx HSIC design has some special requirements, add
some flags at host code to handle them.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Add a field frame_number to the usb_request to report the interval
number in (micro)frames in which the isochronous transfer was
transmitted or received. The gadget driver can use this knowledge to
synchronize with the host. Also, this option is useful for debugging
purposes.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Nothing to remap, only check length.
Define a minimal structure for CCID descriptor only used to check length.
As this descriptor shares the same value as HID descriptors, keep track and
compare current interface's class to expected HID and CCID standard values.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No users of this type anywhere in the tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.
>From USB_PD_R3_0
7.1.5 Response to Hard Resets
Device operation during and after a Hard Reset is defined as follows:
Self-powered devices Should Not disconnect from USB during a Hard Reset
(see Section 9.1.2).
Bus powered devices will disconnect from USB during a Hard Reset due to the
loss of their power source.
Tackle this by letting TCPM know whether the device is self or bus powered.
This overcomes unnecessary port disconnections from hard reset.
Also, speeds up the enumeration time when connected to Type-A ports.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---------
Version history:
V3:
Rebase on top of usb-next
V2:
Based on feedback from heikki.krogerus@linux.intel.com
- self_powered added to the struct tcpm_port which is populated from
a. "connector" node of the device tree in tcpm_fw_get_caps()
b. "self_powered" node of the tcpc_config in tcpm_copy_caps
Based on feedbase from linux@roeck-us.net
- Code was refactored
- SRC_HARD_RESET_VBUS_OFF sets the link state to false based
on self_powered flag
V1 located here:
https://lkml.org/lkml/2018/9/13/94
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting added
to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9LlHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnvwCffYmMWyMG9zSOw1oSzFPl7TVN1hYAoMyJqzLg
umyLwWxC9ZWWkrpc3iD8
=ux+Y
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
Pull tty ioctl updates from Al Viro:
"This is the compat_ioctl work related to tty ioctls.
Quite a bit of dead code taken out, all tty-related stuff gone from
fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
but all more or less generic tty-related ioctls should be covered
(remaining issues are in things like driver-private ioctls in a pcmcia
serial card driver not getting properly handled in 32bit processes on
64bit host, etc)"
* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
kill TIOCSERGSTRUCT
change semantics of ldisc ->compat_ioctl()
kill TIOCSER[SG]WILD
synclink_gt(): fix compat_ioctl()
pty: fix compat ioctls
compat_ioctl - kill keyboard ioctl handling
gigaset: add ->compat_ioctl()
vt_compat_ioctl(): clean up, use compat_ptr() properly
gigaset: don't try to printk userland buffer contents
dgnc: don't bother with (empty) stub for TCXONC
dgnc: leave TIOC[GS]SOFTCAR to ldisc
remove fallback to drivers for TIOCGICOUNT
dgnc: break-related ioctls won't reach ->ioctl()
kill the rest of tty COMPAT_IOCTL() entries
dgnc: TIOCM... won't reach ->ioctl()
isdn_tty: TCSBRK{,P} won't reach ->ioctl()
kill capinc_tty_ioctl()
take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
synclink: reduce pointless checks in ->ioctl()
complete ->[sg]et_serial() switchover
...
add such methods for usb_serial_driver, provide tty_operations
->[sg]et_serial() calling those. For now the lack of methods
in driver means ENOIOCTLCMD from usb-serial ->[sg]et_serial(),
making tty_ioctl() fall back to calling ->ioctl(). Once all
drivers are converted, we'll be returning -ENOTTY instead,
completing the switchover.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The driver_info field that is used for describing each of the usb-net
drivers using the usbnet.c core all declare their information as const
and the usbnet.c itself does not try and modify the struct.
It is therefore a good idea to make this const in the usbnet.c structure
in case anyone tries to modify it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware implementations require to configure pins differently
according to the USB role (host/device), this can be an update of the
pins routing or a simple GPIO value change.
This patch introduces new optional "host" and "device" pinctrls.
If these pinctrls are defined by the device, they are respectively
selected on host/device role start.
If a default pinctrl exist, it is restored on host/device role stop.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this development
cycle:
- lots of type-c work, with drivers graduating out of staging,
and displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot
simpler in the future.
- usbserial driver fixes and reworks
- other misc changes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3hBPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloNwCggMZi9m8Krjq7d7aLw5oJJex/nIAAn0jeADOT
NpoCgrtGHjwrATxN5/Ke
=jXa3
-----END PGP SIGNATURE-----
Merge tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this
development cycle:
- lots of type-c work, with drivers graduating out of staging, and
displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot simpler in
the future.
- usbserial driver fixes and reworks
- other misc changes
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: serial: pl2303: add a new device id for ATEN
usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
usb: dwc3: gadget: Check MaxPacketSize from descriptor
usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
usb: dwc2: Turn on uframe_sched on "amlogic" platforms
usb: dwc2: Turn on uframe_sched on "his" platforms
usb: dwc2: Turn on uframe_sched on "bcm" platforms
usb: dwc2: gadget: ISOC's starting flow improvement
usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
usb: dwc3: core: Enable AutoRetry feature in the controller
usb: dwc3: Set default mode for dwc_usb31
usb: gadget: udc: renesas_usb3: Add register of usb role switch
usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
usb: dwc2: Modify dwc2_readl/writel functions prototype
usb: dwc3: pci: Intel Merrifield can be host
usb: dwc3: pci: Supply device properties via driver data
arm64: dts: dwc3: description of incr burst type
usb: dwc3: Enable undefined length INCR burst type
usb: dwc3: add global soc bus configuration reg0
usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
...
Thee USB Audio Class 3 (UAC3) introduces Power Domains as a new
feature to let a host turn individual parts of an audio function
to different power states via USB requests. This lets the device
get to know a bit amore about what the host is up to in order to
optimize power consumption efficiently.
The Power Domains are optional for UAC3 configuration but all
UAC3 devices shall include at least one BADD configuration where
the support for Power Domains is compulsory.
This patch adds a set of features/helpers to parse these power
domains and change their status.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the Processig Units defined in
the UAC3 spec. The main difference with the previous specs
is the lack of on/off switches in the controls for these
units and the addiction of the new Multi Function Processing
Unit.
The current version of the UAC3 spec doesn't define any
useful controls for the new Multi Function Processing Unit
so no control will get created once this unit is parsed.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds more complete handling of VDMs and registration of
partner alternate modes, and introduces callbacks for
alternate mode operations.
Only DFP role is supported for now.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DisplayPort USB Type-C Alt Mode allows DisplayPort displays
and adapters to be attached to the USB Type-C ports on the
system.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a simple bus for the alternate modes. Bus allows
binding drivers to the discovered alternate modes the
partners support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before a device was created for every discovered SVID, but
this will create a device for every discovered mode of every
SVID. The idea is to make it easier to create mode specific
drivers once a bus for the alternate mode is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the muxes to be usable with alternate modes,
the alternate mode devices will need also to be able to get
a handle to the muxes on top of the port devices. To make
that possible, the muxes need to be possible to request with
an identifier.
This will change the API so that the mux identifier is given
as a function parameter to typec_mux_get(), and the hard-coded
"typec-mux" is replaced with that value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds function typec_get_orientation() that can be used
for checking the current cable plug orientation.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes life a bit easier for the drivers that include
pd.h. All pd_header_*_le() inline functions defined in pd.h
call le16_to_cpu(), and all *_LE() macros in pd.h call
cpu_to_le16().
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds 3 APIs to get the typec port power and data type,
and preferred power role by its name string.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
