[ Upstream commit 8508455961d5a9e8907bcfd8dcd58f19d9b6ce47 ]
There are four modes, and each mode has a table of registers.
Some of the registers are common to all modes, so create new
tables for these common registers to reduce duplicate code.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stable-dep-of: ef86447e775f ("media: i2c: imx219: Fix binning for RAW8 capture")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a967a3a788028f541e4db54beabcebc3648997db ]
Various functions access the media_device from a pad by going through
the entity the pad belongs to. Remove the level of indirection and get
the media_device from the pad directly.
Fixes: 9e3576a1ae ("media: mc: convert pipeline funcs to take media_pad")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7ff69139908842adf824be4f50c7e9ac5886c04 ]
Some module manufacturers [1][2] don't expose the RESETB and PWDN pins
of the sensor directly through the 15-pin FFC connector. Instead wiring
~PWDN gpio to the sensor pins with appropriate delays.
In such cases, reset_gpio will not be available to the driver, but it
will still be toggled when the sensor is powered on, and thus we should
still honor the wait time of >= 5ms + 1ms + 20ms (see figure 2-3 in [3])
before attempting any i/o operations over SCCB.
Also, rename the function to ov5640_powerup_sequence to better match the
datasheet (section 2.7).
[1] https://digilent.com/reference/_media/reference/add-ons/pcam-5c/pcam_5c_sch.pdf
[2] https://www.alinx.com/public/upload/file/AN5641_User_Manual.pdf
[3] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit decea0a98b7ac04536c7d659f74783e8d67a06c0 ]
Move the register-based reset out of the init_setting[] and into the
powerup_sequence function. The sensor is power cycled and reset using
the gpio pins so the soft reset is not always necessary.
This also ensures that soft reset honors the timing sequence
from the datasheet [1].
[1] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Nishanth Menon <nm@ti.com>
Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonaboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9f9cf2560e40b62015c6c4a04be60f55ce5240e ]
For each binary Debian package, a directory with the package name is
created in the debian directory. Correct the generated file matches in the
package's clean target, which were renamed without adjusting the target.
Fixes: 1694e94e4f ("builddeb: match temporary directory name to the package name")
Signed-off-by: Bastian Germann <bage@linutronix.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8589dce8107e2ce62e92f76089654462dd67b4 ]
When clang's -Qunused-arguments is dropped from KBUILD_CPPFLAGS, it
points out that there is a linking phase flag added to CFLAGS, which
will only be used for compiling
clang-16: error: argument unused during compilation: '-shared' [-Werror,-Wunused-command-line-argument]
'-shared' is already present in ldflags-y so it can just be dropped.
Fixes: 2b2a25845d ("s390/vdso: Use $(LD) instead of $(CC) to link vDSO")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31f48f16264bc70962fb3e7ec62da64d0a2ba04a ]
When clang's -Qunused-arguments is dropped from KBUILD_CPPFLAGS, it
points out that KBUILD_AFLAGS contains a linker flag, which will be
unused:
clang: error: -Wl,-a32: 'linker' input unused [-Werror,-Wunused-command-line-argument]
This was likely supposed to be '-Wa,-a$(BITS)'. However, this change is
unnecessary, as all supported versions of clang and gcc will pass '-a64'
or '-a32' to GNU as based on the value of '-m'; the behavior of the
latest stable release of the oldest supported major version of each
compiler is shown below and each compiler's latest release exhibits the
same behavior (GCC 12.2.0 and Clang 15.0.6).
$ powerpc64-linux-gcc --version | head -1
powerpc64-linux-gcc (GCC) 5.5.0
$ powerpc64-linux-gcc -m64 -### -x assembler-with-cpp -c -o /dev/null /dev/null &| grep 'as '
.../as -a64 -mppc64 -many -mbig -o /dev/null /tmp/cctwuBzZ.s
$ powerpc64-linux-gcc -m32 -### -x assembler-with-cpp -c -o /dev/null /dev/null &| grep 'as '
.../as -a32 -mppc -many -mbig -o /dev/null /tmp/ccaZP4mF.sg
$ clang --version | head -1
Ubuntu clang version 11.1.0-++20211011094159+1fdec59bffc1-1~exp1~20211011214622.5
$ clang --target=powerpc64-linux-gnu -fno-integrated-as -m64 -### \
-x assembler-with-cpp -c -o /dev/null /dev/null &| grep gnu-as
"/usr/bin/powerpc64-linux-gnu-as" "-a64" "-mppc64" "-many" "-o" "/dev/null" "/tmp/null-80267c.s"
$ clang --target=powerpc64-linux-gnu -fno-integrated-as -m64 -### \
-x assembler-with-cpp -c -o /dev/null /dev/null &| grep gnu-as
"/usr/bin/powerpc64-linux-gnu-as" "-a32" "-mppc" "-many" "-o" "/dev/null" "/tmp/null-ab8f8d.s"
Remove this flag altogether to avoid future issues.
Fixes: 1421dc6d48 ("powerpc/kbuild: Use flags variables rather than overriding LD/CC/AS")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7acd650a0484d92985a0d6d867d980c6dd019885 ]
The memory of ctx is allocated in cal_ctx_create(), but it will
not be freed when cal_ctx_v4l2_init() fails, so add kfree() when
cal_ctx_v4l2_init() fails to fix it.
Fixes: d68a94e98a ("media: ti-vpe: cal: Split video device initialization and registration")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57f72170a2b2a362c35bb9407fc844eac5afdec1 ]
Any access to the dynamically allocated metadata region by the application
processor after assigning it to the remote Q6 will result in a XPU
violation. Fix this by replacing the dynamically allocated memory region
with a no-map carveout and unmap the modem metadata memory region before
passing control to the remote Q6.
Reported-and-tested-by: Amit Pundir <amit.pundir@linaro.org>
Fixes: 6c5a9dc248 ("remoteproc: qcom: Make secure world call for mem ownership switch")
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117085840.32356-7-quic_sibis@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a899d542b687c9b04ccbd9eefabc829ba5fef791 ]
This reverts commit fc156629b2.
This commit manages to do three API violations at once:
- dereference the return value of dma_alloc_attrs with the
DMA_ATTR_NO_KERNEL_MAPPING mapping, which is clearly forbidden and
will do the wrong thing on various dma mapping implementations. The
fact that dma-direct uses a struct page as a cookie is an undocumented
implementation detail
- include dma-map-ops.h and use pgprot_dmacoherent despite a clear
comment documenting that this is not acceptable
- use of the VM_DMA_COHERENT for something that is not the dma-mapping
code
- use of VM_FLUSH_RESET_PERMS for vmap, while it is only supported for
vmalloc
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117085840.32356-6-quic_sibis@quicinc.com
Stable-dep-of: 57f72170a2b2 ("remoteproc: qcom_q6v5_mss: Use a carveout to authenticate modem headers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8958efe8779d3db19c9124fce593ce681ac709 ]
Fix three sources of error involving struct sdma_txreq.num_descs.
When _extend_sdma_tx_descs() extends the descriptor array, it uses the
value of tx->num_descs to determine how many existing entries from the
tx's original, internal descriptor array to copy to the newly allocated
one. As this value was incremented before the call, the copy loop will
access one entry past the internal descriptor array, copying its contents
into the corresponding slot in the new array.
If the call to _extend_sdma_tx_descs() fails, _pad_smda_tx_descs() then
invokes __sdma_tx_clean() which uses the value of tx->num_desc to drive a
loop that unmaps all descriptor entries in use. As this value was
incremented before the call, the unmap loop will invoke sdma_unmap_desc()
on a descriptor entry whose contents consist of whatever random data was
copied into it during (1), leading to cascading further calls into the
kernel and driver using arbitrary data.
_sdma_close_tx() was using tx->num_descs instead of tx->num_descs - 1.
Fix all of the above by:
- Only increment .num_descs after .descp is extended.
- Use .num_descs - 1 instead of .num_descs for last .descp entry.
Fixes: f4d26d81ad ("staging/rdma/hfi1: Add coalescing support for SDMA TX descriptors")
Link: https://lore.kernel.org/r/167656658879.2223096.10026561343022570690.stgit@awfm-02.cornelisnetworks.com
Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com>
Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0d198f79a8d033bd46605b779859193649f1f99 ]
Fix arithmetic and logic errors in hfi1_can_pin_pages() that would allow
hfi1 to attempt pinning pages in cases where it should not because of
resource limits or lack of required capability.
Fixes: 2c97ce4f3c ("IB/hfi1: Add pin query function")
Link: https://lore.kernel.org/r/167656658362.2223096.10954762619837718026.stgit@awfm-02.cornelisnetworks.com
Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com>
Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a77a52385e9a761f896a88a4162e69fb7ccafe3f ]
An earlier patch which introduced smp_load_acquire/smp_store_release
into rxe_queue.h incorrectly assumed that surrounding spin-locks in
rxe_verbs.c around queue updates for kernel ulps was sufficient to
protect the passing of data through the queues between the ulp and
the rxe tasklets. But this was incorrect. The typical sequence was
ulp rxe requester tasklet
------------------------ ---------------------
spin_lock_irqsave() wqe = queue_head(queue)
if (!queue_full(q)) { if (!wqe)
spin_unlock_irqrestore return;
return -ENOMEM
} <process wqe>
wqe = queue_producer_addr(q)
<fill in wqe> queue_advance_consumer(queue)
queue_advance_producer(q)
spin_unlock_irqrestore()
queue_head() calls queue_empty() which calls smp_load_acquire()
For user space apps queue_advance_producer() calls smp_store_release()
so that there is a memory barrier between the producer and the
consumer but for kernel ulps queue_advance_produce() just incremented
the producer index because the lock function is a release function.
But to work the barrier has to come between filling in the wqe and
updating the producer index. This patch adds the missing barriers.
It also changes the enum names for the ulp queue types to
QUEUE_TYPE_FROM/TO_ULP instead of QUEUE_TYPE_TO/FROM_DRIVER
which is very ambiguous. This bug is suspected as the cause of very
rare lockups in a very high scale storage application. It is a bug
in any case and should be corrected.
Fixes: 0a67c46d2e ("RDMA/rxe: Protect user space index loads/stores")
Link: https://lore.kernel.org/r/20230214071053.5395-1-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 692373d186205dfb1b56f35f22702412d94d9420 ]
Instead of 'goto and return', just return directly to
simplify the error handling, and avoid some unnecessary
return value check.
Link: https://lore.kernel.org/r/20221028075053.3990467-1-xuhaoyue1@hisilicon.com
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: a77a52385e9a ("RDMA/rxe: Fix missing memory barriers in rxe_queue.h")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 257ec290741924f8df678927d0dfecb1deebb9c5 ]
Commit 29b3283972 ("iommu/vt-d: Do not use flush-queue when caching-mode
is on") forced default domains to be strict mode as long as IOMMU
caching-mode is flagged. The reason for doing this is that when vIOMMU
uses VT-d caching mode to synchronize shadowing page tables, the strict
mode shows better performance.
However, this optimization is orthogonal to the first-level page table
because the Intel VT-d architecture does not define the caching mode of
the first-level page table. Refer to VT-d spec, section 6.1, "When the
CM field is reported as Set, any software updates to remapping
structures other than first-stage mapping (including updates to not-
present entries or present entries whose programming resulted in
translation faults) requires explicit invalidation of the caches."
Exclude the first-level page table from this optimization.
Generally using first-stage translation in vIOMMU implies nested
translation enabled in the physical IOMMU. In this case the first-stage
page table is wholly captured by the guest. The vIOMMU only needs to
transfer the cache invalidations on vIOMMU to the physical IOMMU.
Forcing the default domain to strict mode will cause more frequent
cache invalidations, resulting in performance degradation. In a real
performance benchmark test measured by iperf receive, the performance
result on Sapphire Rapids 100Gb NIC shows:
w/ this fix ~51 Gbits/s, w/o this fix ~39.3 Gbits/s.
Theoretically a first-stage IOMMU page table can still be shadowed
in absence of the caching mode, e.g. with host write-protecting guest
IOMMU page table to synchronize changed PTEs with the physical
IOMMU page table. In this case the shadowing overhead is decoupled
from emulating IOTLB invalidation then the overhead of the latter part
is solely decided by the frequency of IOTLB invalidations. Hence
allowing guest default dma domain to be lazy can also benefit the
overall performance by reducing the total VM-exit numbers.
Fixes: 29b3283972 ("iommu/vt-d: Do not use flush-queue when caching-mode is on")
Reported-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Suggested-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20230214025618.2292889-1-tina.zhang@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60b1daa3b168fbc648ae2ad28a84759223e49e18 ]
Roll back all previous actions in error paths of intel_iommu_enable_sva()
and intel_iommu_disable_sva().
Fixes: d5b9e4bfe0 ("iommu/vt-d: Report prq to io-pgfault framework")
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20230208051559.700109-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 928469986171a6f763b34b039427f5667ba3fd50 ]
Resolves a panic that can occur on AMD systems, typically during host
shutdown, after the PTDMA driver had been exercised. The issue was
the pt_issue_pending() function is mistakenly assuming that there will
be at least one descriptor in the Submitted queue when the function
is called. However, it is possible that both the Submitted and Issued
queues could be empty, which could result in pt_cmd_callback() being
mistakenly called with a NULL pointer.
Ref: Bugzilla Bug 216856.
Fixes: 6fa7e0e836 ("dmaengine: ptdma: fix concurrency issue with multiple dma transfer")
Signed-off-by: Eric Pilmore <epilmore@gigaio.com>
Link: https://lore.kernel.org/r/20230210075142.58253-1-epilmore@gigaio.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b02e07015a5ac7bbc029da931ae17914b8ae0339 ]
Commit b2cc5c465c ("dmaengine: sf-pdma: Add multithread support for a
DMA channel") changed sf_pdma_prep_dma_memcpy() to unconditionally
allocate a new sf_pdma_desc each time it is called.
The driver previously recycled descs, by checking the in_use flag, only
allocating additional descs if the existing one was in use. This logic
was removed in commit b2cc5c465c ("dmaengine: sf-pdma: Add multithread
support for a DMA channel"), but sf_pdma_free_desc() was not changed to
handle the new behaviour.
As a result, each time sf_pdma_prep_dma_memcpy() is called, the previous
descriptor is leaked, over time leading to memory starvation:
unreferenced object 0xffffffe008447300 (size 192):
comm "irq/39-mchp_dsc", pid 343, jiffies 4294906910 (age 981.200s)
hex dump (first 32 bytes):
00 00 00 ff 00 00 00 00 b8 c1 00 00 00 00 00 00 ................
00 00 70 08 10 00 00 00 00 00 00 c0 00 00 00 00 ..p.............
backtrace:
[<00000000064a04f4>] kmemleak_alloc+0x1e/0x28
[<00000000018927a7>] kmem_cache_alloc+0x11e/0x178
[<000000002aea8d16>] sf_pdma_prep_dma_memcpy+0x40/0x112
Add the missing kfree() to sf_pdma_free_desc(), and remove the redundant
in_use flag.
Fixes: b2cc5c465c ("dmaengine: sf-pdma: Add multithread support for a DMA channel")
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230120100623.3530634-1-shravan.chippa@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18792e99ea2fea27c72eb1ecca1879e5e6be304d ]
Flow:
- Booted system with SNP enabled, memory encryption off and
IOMMU DMA translation mode
- AMD driver detects v2 capable device and amd_iommu_def_domain_type()
returns identity mode
- amd_iommu_domain_alloc() returns NULL an SNP is enabled
- System will fail to register device
On SNP enabled system, passthrough mode is not supported. IOMMU default
domain is set to translation mode. We need to return zero from
amd_iommu_def_domain_type() so that it allocates translation domain.
Fixes: fb2accadaa ("iommu/amd: Introduce function to check and enable SNP")
CC: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20230207091752.7656-1-vasant.hegde@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4daa861174d56023c2068ddb03de0752f07fa199 ]
If either iommu_group_grate_file() fails then the
iommu_group is leaked.
Destroy it on these error paths.
Found by kselftest/iommu/iommufd_fail_nth
Fixes: bc7d12b91b ("iommu: Implement reserved_regions iommu-group sysfs file")
Fixes: c52c72d3de ("iommu: Add sysfs attribyte for domain type")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/0-v1-8f616bee028d+8b-iommu_group_alloc_leak_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca446b127c568b59cb8d9748b6f70499624bb18 ]
This condition needs to match the previous "if (epcp->state == LISTEN) {"
exactly to avoid a NULL dereference of either "listen_ep" or "ep". The
problem is that "epcp" has been re-assigned so just testing
"if (epcp->state == LISTEN) {" a second time is not sufficient.
Fixes: 116aeb8873 ("iw_cxgb4: provide detailed provider-specific CM_ID information")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y+usKuWIKr4dimZh@kili
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 997e010de9134474dbfde52be03efd7d1bce902d ]
Implement the new host_deinit() callback so that the PHY is powered off
and regulators and clocks are disabled also on late host-init errors.
Link: https://lore.kernel.org/r/20221017114705.8277-2-johan+linaro@kernel.org
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca651df07183e29cdad7272255e23aec0169a1b ]
The existing logic in tcphy_get_mode() can cause the phy to be
incorrectly configured to USB UFP or DisplayPort mode when
extcon_get_state returns an error code.
extcon_get_state() can return 0, 1, or a negative error code.
It is possible to get into the failing state with an extcon driver
which does not support the extcon connector id specified as the
second argument to extcon_get_state().
tcphy_get_mode()
->extcon_get_state()
-->find_cable_index_by_id()
--->return -EINVAL;
Fixes: e96be45cb8 ("phy: Add USB Type-C PHY driver for rk3399")
Signed-off-by: Neill Kapron <nkapron@google.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230126001013.3707873-1-nkapron@google.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d8ba74a181b1c81def21168795ed96cbe6f05ed ]
On r8a7791/koelsch:
kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xc3a34e00 (size 64):
comm "swapper/0", pid 1, jiffies 4294937460 (age 199.080s)
hex dump (first 32 bytes):
b4 5d 81 f0 b4 5d 81 f0 c0 b0 a2 c3 00 00 00 00 .]...]..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fe3aa979>] __kmalloc+0xf0/0x140
[<34bd6bc0>] resource_list_create_entry+0x18/0x38
[<767046bc>] pci_add_resource_offset+0x20/0x68
[<b3f3edf2>] devm_of_pci_get_host_bridge_resources.constprop.0+0xb0/0x390
When coalescing two resources for a contiguous aperture, the second
resource is enlarged to cover the full contiguous range, while the first
resource is marked invalid. This invalidation is done by clearing the
flags, start, and end members.
When adding the initial resources to the bus later, invalid resources are
skipped. Unfortunately, the check for an invalid resource considers only
the end member, causing false positives.
E.g. on r8a7791/koelsch, root bus resource 0 ("bus 00") is skipped, and no
longer registered with pci_bus_insert_busn_res() (causing the memory leak),
nor printed:
pci-rcar-gen2 ee090000.pci: host bridge /soc/pci@ee090000 ranges:
pci-rcar-gen2 ee090000.pci: MEM 0x00ee080000..0x00ee08ffff -> 0x00ee080000
pci-rcar-gen2 ee090000.pci: PCI: revision 11
pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00
-pci_bus 0000:00: root bus resource [bus 00]
pci_bus 0000:00: root bus resource [mem 0xee080000-0xee08ffff]
Fix this by only skipping resources where all of the flags, start, and end
members are zero.
Fixes: 7c3855c423 ("PCI: Coalesce host bridge contiguous apertures")
Link: https://lore.kernel.org/r/da0fcd5e86c74239be79c7cb03651c0fce31b515.1676036673.git.geert+renesas@glider.be
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fdca4a995bcd4cf61bda40af154a730589dc524 ]
Previously, readq_ch() did a 64-bit readq(), but truncated the result by
storing it in the u32 "value". Change "value" to u64 to avoid the
truncation.
Note: the method is currently unused, so the bug hasn't caused any problem
so far.
Fixes: 04e0a39fc1 ("dmaengine: dw-edma: Add writeq() and readq() for 64 bits architectures")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb42378dcc7f247df56f0ecddfdae85487495fbc ]
These "nvmem-cells" platform devices never get probed because there's no
platform driver for it and it's never used anywhere else. So it's a
waste of memory. These devices also cause fw_devlink to block nvmem
consumers of "nvmem-cells" partition from probing because the supplier
device never probes.
So stop creating platform devices for nvmem-cells partitions to avoid
wasting memory and to avoid blocking probing of consumers.
Reported-by: Maxim Kiselev <bigunclemax@gmail.com>
Fixes: bcdf0315a6 ("mtd: call of_platform_populate() for MTD partitions")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Maksim Kiselev <bigunclemax@gmail.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-13-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fb16866b51ded6c016b664caad53f8d4fd9dc56 ]
fw_devlink could only detect a single and simple cycle because it relied
mainly on device link cycle detection code that only checked for cycles
between devices. The expectation was that the firmware wouldn't have
complicated cycles and multiple cycles between devices. That expectation
has been proven to be wrong.
For example, fw_devlink could handle:
+-+ +-+
|A+------> |B+
+-+ +++
^ |
| |
+----------+
But it couldn't handle even something as "simple" as:
+---------------------+
| |
v |
+-+ +-+ +++
|A+------> |B+------> |C|
+-+ +++ +-+
^ |
| |
+----------+
But firmware has even more complicated cycles like:
+---------------------+
| |
v |
+-+ +---+ +++
+--+A+------>| B +-----> |C|<--+
| +-+ ++--+ +++ |
| ^ | ^ | |
| | | | | |
| +---------+ +---------+ |
| |
+------------------------------+
And this is without including parent child dependencies or nodes in the
cycle that are just firmware nodes that'll never have a struct device
created for them.
The proper way to treat these devices it to not force any probe ordering
between them, while still enforce dependencies between node in the
cycles (A, B and C) and their consumers.
So this patch goes all out and just deals with all types of cycles. It
does this by:
1. Following dependencies across device links, parent-child and fwnode
links.
2. When it find cycles, it mark the device links and fwnode links as
such instead of just deleting them or making the indistinguishable
from proxy SYNC_STATE_ONLY device links.
This way, when new nodes get added, we can immediately find and mark any
new cycles whether the new node is a device or firmware node.
Fixes: 2de9d8e0d2 ("driver core: fw_devlink: Improve handling of cyclic dependencies")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-9-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 411c0d58ca6faa9bc4b9f5382118a31c7bb92a6f ]
fw_devlink shouldn't defer the probe of a device to wait on a supplier
that'll never have a struct device or will never be probed by a driver.
We currently check if a supplier falls into this category, but don't
check its ancestors. We need to check the ancestors too because if the
ancestor will never probe, then the supplier will never probe either.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3fb16866b51d ("driver core: fw_devlink: Make cycle detection more robust")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd115c0409f283edde94bd5a9a42dc42bee0aba8 ]
Consolidate the code that computes the flags to be used when creating a
device link from a fwnode link.
Fixes: 2de9d8e0d2 ("driver core: fw_devlink: Improve handling of cyclic dependencies")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-8-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a6dfdf8b3ff337be5a447e9f4e71969f18370ad ]
To improve detection and handling of dependency cycles, we need to be
able to mark fwnode links as being part of cycles. fwnode links marked
as being part of a cycle should not block their consumers from probing.
Fixes: 2de9d8e0d2 ("driver core: fw_devlink: Improve handling of cyclic dependencies")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-7-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a2dbc510c437ca392516b0105bad8e7970e6614 ]
When a device X is bound successfully to a driver, if it has a child
firmware node Y that doesn't have a struct device created by then, we
delete fwnode links where the child firmware node Y is the supplier. We
did this to avoid blocking the consumers of the child firmware node Y
from deferring probe indefinitely.
While that a step in the right direction, it's better to make the
consumers of the child firmware node Y to be consumers of the device X
because device X is probably implementing whatever functionality is
represented by child firmware node Y. By doing this, we capture the
device dependencies more accurately and ensure better
probe/suspend/resume ordering.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-2-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 6a6dfdf8b3ff ("driver core: fw_devlink: Allow marking a fwnode link as being part of a cycle")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67cad5c67019c38126b749621665b6723d3ae7e6 ]
fw_devlink uses DL_FLAG_SYNC_STATE_ONLY device link flag for two
purposes:
1. To allow a parent device to proxy its child device's dependency on a
supplier so that the supplier doesn't get its sync_state() callback
before the child device/consumer can be added and probed. In this
usage scenario, we need to ignore cycles for ensure correctness of
sync_state() callbacks.
2. When there are dependency cycles in firmware, we don't know which of
those dependencies are valid. So, we have to ignore them all wrt
probe ordering while still making sure the sync_state() callbacks
come correctly.
However, when detecting dependency cycles, there can be multiple
dependency cycles between two devices that we need to detect. For
example:
A -> B -> A and A -> C -> B -> A.
To detect multiple cycles correct, we need to be able to differentiate
DL_FLAG_SYNC_STATE_ONLY device links used for (1) vs (2) above.
To allow this differentiation, add a DL_FLAG_CYCLE that can be use to
mark use case (2). We can then use the DL_FLAG_CYCLE to decide which
DL_FLAG_SYNC_STATE_ONLY device links to follow when looking for
dependency cycles.
Fixes: 2de9d8e0d2 ("driver core: fw_devlink: Improve handling of cyclic dependencies")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-6-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef25e16ea9674b713a68c3bda821556ce9901254 ]
There maybe pending USR interrupt before requesting irq, however
uart_add_one_port has not executed, so there will be kernel panic:
[ 0.795668] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000000000000080
[ 0.802701] Mem abort info:
[ 0.805367] ESR = 0x0000000096000004
[ 0.808950] EC = 0x25: DABT (current EL), IL = 32 bits
[ 0.814033] SET = 0, FnV = 0
[ 0.816950] EA = 0, S1PTW = 0
[ 0.819950] FSC = 0x04: level 0 translation fault
[ 0.824617] Data abort info:
[ 0.827367] ISV = 0, ISS = 0x00000004
[ 0.831033] CM = 0, WnR = 0
[ 0.833866] [0000000000000080] user address but active_mm is swapper
[ 0.839951] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 0.845953] Modules linked in:
[ 0.848869] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.1+g56321e101aca #1
[ 0.855617] Hardware name: Freescale i.MX8MP EVK (DT)
[ 0.860452] pstate: 000000c5 (nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.867117] pc : __imx_uart_rxint.constprop.0+0x11c/0x2c0
[ 0.872283] lr : imx_uart_int+0xf8/0x1ec
The issue only happends in the inmate linux when Jailhouse hypervisor
enabled. The test procedure is:
while true; do
jailhouse enable imx8mp.cell
jailhouse cell linux xxxx
sleep 10
jailhouse cell destroy 1
jailhouse disable
sleep 5
done
And during the upper test, press keys to the 2nd linux console.
When `jailhouse cell destroy 1`, the 2nd linux has no chance to put
the uart to a quiese state, so USR1/2 may has pending interrupts. Then
when `jailhosue cell linux xx` to start 2nd linux again, the issue
trigger.
In order to disable irqs before requesting them, both UCR1 and UCR2 irqs
should be disabled, so here fix that, disable the Ageing Timer interrupt
in UCR2 as UCR1 does.
Fixes: 8a61f0c70a ("serial: imx: Disable irqs before requesting them")
Suggested-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20230206013016.29352-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79d0224f6bf296d04cd843cfc49921b19c97bb09 ]
The default polarity of RS485 DE signal is active high. This driver does
not handle such case properly. Currently, when a pin is multiplexed as a
UART CTS_B on boot, this pin is pulled HIGH by the i.MX UART CTS circuit,
which activates DE signal on the RS485 transceiver and thus behave as if
the RS485 was transmitting data, so the system blocks the RS485 bus when
it starts and until user application takes over. This behavior is not OK.
The problem consists of two separate parts.
First, the i.MX UART IP requires UCR1 UARTEN and UCR2 RXEN to be set for
UCR2 CTSC and CTS bits to have any effect. The UCR2 CTSC bit permits the
driver to set CTS (RTS_B or RS485 DE signal) to either level sychronous
to the internal UART IP clock. Compared to other options, like GPIO CTS
control, this has the benefit of being synchronous to the UART IP clock
and thus without glitches or bus delays. The reason for the CTS design
is likely because when the Receiver is disabled, the UART IP can never
indicate that it is ready to receive data by assering CTS signal, so
the CTS is always pulled HIGH by default.
When the port is closed by user space, imx_uart_stop_rx() clears UCR2
RXEN bit, and imx_uart_shutdown() clears UCR1 UARTEN bit. This disables
UART Receiver and UART itself, and forces CTS signal HIGH, which leads
to the RS485 bus being blocked because RS485 DE is incorrectly active.
The proposed solution for this problem is to keep the Receiver running
even after the port is closed, but in loopback mode. This disconnects
the RX FIFO input from the RXD external signal, and since UCR2 TXEN is
cleared, the UART Transmitter is disabled, so nothing can feed data in
the RX FIFO. Because the Receiver is still enabled, the UCR2 CTSC and
CTS bits still have effect and the CTS (RS485 DE) control is retained.
Note that in case of RS485 DE signal active low, there is no problem and
no special handling is necessary. The CTS signal defaults to HIGH, thus
the RS485 is by default set to Receive and the bus is not blocked.
Note that while there is the possibility to control CTS using GPIO with
either CTS polarity, this has the downside of not being synchronous to
the UART IP clock and thus glitchy and susceptible to slow DE switching.
Second, on boot, before the UART driver probe callback is called, the
driver core triggers pinctrl_init_done() and configures the IOMUXC to
default state. At this point, UCR1 UARTEN and UCR2 RXEN are both still
cleared, but UART CTS_B (RS485 DE) is configured as CTS function, thus
the RTS signal is pulled HIGH by the UART IP CTS circuit.
One part of the solution here is to enable UCR1 UARTEN and UCR2 RXEN and
UTS loopback in this driver probe callback, thus unblocking the CTSC and
CTS control early on. But this is still too late, since the pin control
is already configured and CTS has been pulled HIGH for a short period
of time.
When Linux kernel boots and this driver is bound, the pin control is set
to special "init" state if the state is available, and driver can switch
the "default" state afterward when ready. This state can be used to set
the CTS line as a GPIO in DT temporarily, and a GPIO hog can force such
GPIO to LOW, thus keeping the RS485 DE line LOW early on boot. Once the
driver takes over and UCR1 UARTEN and UCR2 RXEN and UTS loopback are all
enabled, the driver can switch to "default" pin control state and control
the CTS line as function instead. DT binding example is below:
"
&gpio6 {
rts-init-hog {
gpio-hog;
gpios = <5 0>;
output-low;
line-name = "rs485-de";
};
};
&uart5 { /* DHCOM UART2 */
pinctrl-0 = <&pinctrl_uart5>;
pinctrl-1 = <&pinctrl_uart5_init>;
pinctrl-names = "default", "init";
...
};
pinctrl_uart5_init: uart5-init-grp {
fsl,pins = <
...
MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x30b1
>;
};
pinctrl_uart5: uart5-grp {
fsl,pins = <
...
MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x30b1
>;
};
"
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220929144400.13571-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ef25e16ea967 ("tty: serial: imx: disable Ageing Timer interrupt request irq")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3957b9501a5a8fa709ae4a47483714491471f6db ]
The previous 'commit 846651eca0 ("serial: fsl_lpuart: RS485 RTS
polariy is inverse")' only fixed the inverse issue on lpuart 8bit
platforms.
This is a follow-up patch to fix the RS485 polarity inverse
issue on lpuart 32bit platforms.
Fixes: 03895cf41d ("tty: serial: fsl_lpuart: Add support for RS-485")
Reported-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230207162420.3647904-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7efe3fc7cbe27c6eb2c2a3ab612194f8f800f4c ]
To update the I/O pins, the registers are read/modified/written. The
read operation incorrectly always read the first register. Although
wrong, there wasn't any impact as all the output pins are always
written, and the inputs are read only anyway.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230207033337.18112-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 283861a4c52c1ea4df3dd1b6fc75a50796ce3524 ]
If get_ep_from_tid() fails to lookup non-NULL value for ep, ep is
dereferenced later regardless of whether it is empty.
This patch adds a simple sanity check to fix the issue.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 944661dd97 ("RDMA/iw_cxgb4: atomically lookup ep and get a reference")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230202184850.29882-1-n.zhandarovich@fintech.ru
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c85c191694cb1cf290b11059b3d2de8a2732ffd0 ]
The rn5t618 power driver fails to register
a cooling device because POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX
is missing but availability is not checked before registering
cooling device. After improved error checking in the thermal
code, the registration of the power supply fails entirely.
Checking for availability of _MAX before registering cooling device
fixes the rn5t618 problem. But the whole logic feels questionable.
First, the logic is inverted here:
the code tells: max_current = max_cooling but
0 = max_cooling, so there needs to be some inversion
in the code which cannot be found. Comparing with other
cooling devices, it can be found that value for fan speed is not
inverted, value for cpufreq cooling is inverted (similar situation
as here lowest frequency = max cooling)
Second, analyzing usage of _MAX: it is seems that maximum capabilities
of charging controller are specified and not of the battery. Probably
there is not too much mismatch in the drivers actually implementing
that. So nothing has exploded yet. So there is no easy and safe way
to specifify a max cooling value now.
Conclusion for now (as a regression fix) just remove the cooling device
registration and do it properly later on.
Fixes: e49a1e1ee078 ("thermal/core: fix error code in __thermal_cooling_device_register()")
Fixes: 952aeeb3ee ("power_supply: Register power supply for thermal cooling device")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e06d24435596c8afcaa81c0c498f5b0ec4ee2b7c ]
Setup No Execute Enable bit (Bit 133) of a scalable mode PASID entry.
This is to allow the use of XD bit of the first level page table.
Fixes: ddf09b6d43 ("iommu/vt-d: Setup pasid entries for iova over first level")
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20230126095438.354205-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf5c1c87c2391649e05e58ecc6dfc3dc5ebebc05 ]
pci_device_group() can return an already existing IOMMU group if the PCI
device's pagetables have to be shared with another one due to bus
toplogy, isolation features and/or DMA alias quirks.
apple_dart_device_group() however assumes that the group has just been
created and overwrites its iommudata which will eventually lead to
apple_dart_release_group leaving stale entries in sid2group.
Fix that by merging the iommudata if the returned group already exists.
Fixes: f0b636804c ("iommu/dart: Clear sid2group entry when a group is freed")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Link: https://lore.kernel.org/r/20230128113532.94651-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 510d4072df7fcf27dcd2dc1942d58b2cc02b03f2 ]
T8110 DARTs have up to 256 SIDs, so we need to switch to a bitmap to
handle them properly.
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230113105029.26654-4-marcan@marcan.st
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Stable-dep-of: cf5c1c87c239 ("iommu/dart: Fix apple_dart_device_group for PCI groups")
Signed-off-by: Sasha Levin <sashal@kernel.org>
