In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This fixes what appears to be a bug
in passing the wrong pointer to the timer handler (address of ctrl pointer
instead of ctrl pointer).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Combine two error paths that emit the same message and return the same
error code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some of the PCIe services such as AER are being left enabled during
shutdown. This might cause spurious AER errors while SOC is being powered
down.
Clean up the PCIe services gracefully during shutdown to clear these false
positives.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make the PCI bus type take DPM_FLAG_SMART_SUSPEND into account in its
system-wide PM callbacks and make sure that all code that should not
run in parallel with pci_pm_runtime_resume() is executed in the "late"
phases of system suspend, freeze and poweroff transitions.
[Note that the pm_runtime_suspended() check in pci_dev_keep_suspended()
is an optimization, because if is not passed, all of the subsequent
checks may be skipped and some of them are much more overhead in
general.]
Also use the observation that if the device is in runtime suspend
at the beginning of the "late" phase of a system-wide suspend-like
transition, its state cannot change going forward (runtime PM is
disabled for it at that time) until the transition is over and the
subsequent system-wide PM callbacks should be skipped for it (as
they generally assume the device to not be suspended), so add checks
for that in pci_pm_suspend_late/noirq(), pci_pm_freeze_late/noirq()
and pci_pm_poweroff_late/noirq().
Moreover, if pci_pm_resume_noirq() or pci_pm_restore_noirq() is
called during the subsequent system-wide resume transition and if
the device was left in runtime suspend previously, its runtime PM
status needs to be changed to "active" as it is going to be put
into the full-power state, so add checks for that too to these
functions.
In turn, if pci_pm_thaw_noirq() runs after the device has been
left in runtime suspend, the subsequent "thaw" callbacks need
to be skipped for it (as they may not work correctly with a
suspended device), so set the power.direct_complete flag for the
device then to make the PM core skip those callbacks.
In addition to the above add a core helper for checking if
DPM_FLAG_SMART_SUSPEND is set and the device runtime PM status is
"suspended" at the same time, which is done quite often in the new
code (and will be done elsewhere going forward too).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The only user of non-empty pcibios_pm_ops is s390 and it only uses
"noirq" callbacks, so drop the invocations of the other pcibios_pm_ops
callbacks from the PCI PM code.
That will allow subsequent changes to be somewhat simpler.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace the PCI-specific flag PCI_DEV_FLAGS_NEEDS_RESUME with the
PM core's DPM_FLAG_NEVER_SKIP one everywhere and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The motivation for this change is to provide a way to work around
a problem with the direct-complete mechanism used for avoiding
system suspend/resume handling for devices in runtime suspend.
The problem is that some middle layer code (the PCI bus type and
the ACPI PM domain in particular) returns positive values from its
system suspend ->prepare callbacks regardless of whether the driver's
->prepare returns a positive value or 0, which effectively prevents
drivers from being able to control the direct-complete feature.
Some drivers need that control, however, and the PCI bus type has
grown its own flag to deal with this issue, but since it is not
limited to PCI, it is better to address it by adding driver flags at
the core level.
To that end, add a driver_flags field to struct dev_pm_info for flags
that can be set by device drivers at the probe time to inform the PM
core and/or bus types, PM domains and so on on the capabilities and/or
preferences of device drivers. Also add two static inline helpers
for setting that field and testing it against a given set of flags
and make the driver core clear it automatically on driver remove
and probe failures.
Define and document two PM driver flags related to the direct-
complete feature: NEVER_SKIP and SMART_PREPARE that can be used,
respectively, to indicate to the PM core that the direct-complete
mechanism should never be used for the device and to inform the
middle layer code (bus types, PM domains etc) that it can only
request the PM core to use the direct-complete mechanism for
the device (by returning a positive value from its ->prepare
callback) if it also has been requested by the driver.
While at it, make the core check pm_runtime_suspended() when
setting power.direct_complete so that it doesn't need to be
checked by ->prepare callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
*) Add support in phy core to perform phy calibration
*) Return NULL for optional PHY's even if CONFIG_GENERIC_PHY is not selected
*) Add USB Phy driver for Broadcom STB SoCs
*) Add support to force mediatek PHY with USB OTG function to enter
a specific mode
*) Calibrate rockchip-typec PHY according to docs
*) Enable dual route feature for sun4i-usb in V3s SoC
*) Use dr_mode dt property to enable otg capability in rcar-gen3-usb2
*) Add driver data to specify dedicated otg pins in rcar-gen3-usb2 driver
*) Configure the RX equalizer of brcm-sata PHY
*) Update pcie phy settings for ti-pipe3 phy
*) Add set_mode callback in qcom-ufs-qmp-14nm phy
*) Use PHY callbacks in phy-qcom-ufs instead of export APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VvPn
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.15_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.15
*) Add support in phy core to perform phy calibration
*) Return NULL for optional PHY's even if CONFIG_GENERIC_PHY is not selected
*) Add USB Phy driver for Broadcom STB SoCs
*) Add support to force mediatek PHY with USB OTG function to enter
a specific mode
*) Calibrate rockchip-typec PHY according to docs
*) Enable dual route feature for sun4i-usb in V3s SoC
*) Use dr_mode dt property to enable otg capability in rcar-gen3-usb2
*) Add driver data to specify dedicated otg pins in rcar-gen3-usb2 driver
*) Configure the RX equalizer of brcm-sata PHY
*) Update pcie phy settings for ti-pipe3 phy
*) Add set_mode callback in qcom-ufs-qmp-14nm phy
*) Use PHY callbacks in phy-qcom-ufs instead of export APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The pci_reset_function() path may try several different reset methods:
device-specific resets, PCIe Function Level Resets, PCI Advanced Features
Function Level Reset, etc.
Add a comment about what the return values from these methods mean. If one
of the methods fails, in some cases we want to continue and try the next
one in the list, but sometimes we want to stop trying.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a pci_resize_resource() interface to allow device drivers to resize
BARs of their devices.
This is useful for devices with large local storage, e.g., graphics
devices. These devices often only expose 256MB BARs initially to be
compatible with 32-bit systems.
This function only tries to reprogram the windows of the bridge directly
above the requesting device and only the BAR of the same type (usually mem,
64bit, prefetchable). This is done to avoid disturbing other drivers by
changing the BARs of their devices.
Drivers should use the following sequence to resize their BARs:
1. Disable memory decoding of the device using the PCI cfg dword.
2. Use pci_release_resource() to release all BARs which can move during the
resize, including the one you want to resize.
3. Call pci_resize_resource() for each BAR you want to resize.
4. Call pci_assign_unassigned_bus_resources() to reassign new locations
for all BARs which are not resized, but could move.
5. If everything worked as expected, enable memory decoding in the device
again using the PCI cfg dword.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When removing a device, for example a VF being removed due to SR-IOV
teardown, a "soft" hot-unplug via 'echo 1 > remove' in sysfs, or an actual
hot-unplug, we first remove the procfs and sysfs attributes for the device
before attempting to release the device from any driver bound to it.
Unbinding the driver from the device can take time. The device might need
to write out data or it might be actively in use. If it's in use by
userspace through a vfio driver, the unbind might block until the user
releases the device. This leads to a potentially non-trivial amount of
time where the device exists, but we've torn down the interfaces that
userspace uses to examine devices, for instance lspci might generate this
sort of error:
pcilib: Cannot open /sys/bus/pci/devices/0000:01:0a.3/config
lspci: Unable to read the standard configuration space header of device 0000:01:0a.3
We don't seem to have any dependence on this teardown ordering in the
kernel, so let's unbind the driver first, which is also more symmetric with
the instantiation of the device in pci_bus_add_device().
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a HiSilicon STB SoC PCIe controller driver. This controller is based
on the DesignWare PCIe core.
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add resizable BAR infrastructure, including defines and helper functions to
read the possible sizes of a BAR and update its size. See PCIe r3.1, sec
7.22.
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_Resizable-BAR_24Apr2008.pdf
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: rename to functions with "rebar" (to match #defines), drop shift
#defines, drop "_MASK" suffixes, fix typos, fix kerneldoc]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Add a #define for the PCI resource type mask. We use this mask multiple
times in the bus setup.
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: move to setup-bus.c]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
PCI core access configuration space registers in resume_noirq callbacks.
In the case of dra7xx, PIPE3 PHY connected to PCIe controller has to be
enabled before accessing configuration space registers. Since
PIPE3 PHY is enabled by only configuring control module registers, no
aborts has been observed so far (though during noirq stage, interface
clock of PIPE3 PHY is not enabled).
With new TRM updates, PIPE3 PHY has to be initialized (PIPE3 PHY
registers has to be accessed) as well which requires the interface
clock of PIPE3 PHY to be enabled. The interface clock of PIPE3 PHY is
derived from OCP2SCP and hence PCIe PHY is modeled as a child of
OCP2SCP. Since pm_runtime is not enabled during noirq stage,
pm_runtime_get_sync done in phy_init doesn't enable
OCP2SCP clocks resulting in abort when PIPE3 PHY registers are
accessed.
Create a function dependency between PCIe and PHY here to make
sure PCIe is suspended before PCIe PHY/OCP2SCP and resumed after
PCIe PHY/OCP2SCP.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
When setting up portdrv MSI/MSI-X interrupts, we previously allocated the
maximum possible number of vectors, read the Interrupt Message Numbers for
each service, saved the IRQ for each, freed the vectors, and finally used
the largest Message Number to reallocate only as many vectors as we need.
The problem is that freeing the vectors invalidates their IRQs, so the
saved IRQ numbers may now be invalid, which can result in errors like
this:
pcie_pme: probe of 0000:00:00.0:pcie001 failed with error -22
pciehp 0000:00:00.0:pcie004: Cannot get irq 20 for the hotplug controller
aer: probe of 0000:00:00.0:pcie002 failed with error -22
dpc 0000:00:00.0:pcie010: request IRQ22 failed: -22
Change the setup so we save the Interrupt Message Numbers (not the IRQs)
before we free the original setup, then use the Message Numbers to compute
the IRQs (via pci_irq_vector()) *after* we reallocate the vectors.
This should always be safe for MSI-X because the Message Numbers are fixed.
For MSI, the hardware is allowed to change Message Numbers when we update
the MSI Multiple Message Enable field when reallocating the vectors, but
since we allocate enough vectors to accommodate the largest Message Number
we found, that's unlikely. See PCIe r3.1, sec 7.8.2, 7.10.10, 7.31.2.
Fixes: 3674cc49da9a ("PCI/portdrv: Use pci_irq_alloc_vectors()")
Based-on-patch-by: Dongdong Liu <liudongdong3@huawei.com>
Tested-by: Dongdong Liu <liudongdong3@huawei.com> # HiSilicon hip08
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
PTR_ERR should access the value just tested by IS_ERR, otherwise the wrong
error code will be returned.
Fixes: 2eeb02b28579 ("PCI: faraday: Add clock handling")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
By default, when the PCIe controller experiences an erroneous completion
from an external completer for its outbound non-posted request, it sends
an OKAY response to the device's internal AXI slave system interface.
However, this default system error response behavior cannot be used for
other types of outbound non-posted requests. For example, the outbound
memory read transaction requires an actual ERROR response, like UR
completion or completion timeout.
Fix this by forwarding the error response of the non-posted request.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Freescale PCIe controller advertises the MSI/MSI-X capability in both
RC and Endpoint mode, but in RC mode it doesn't support MSI/MSI-X by
itself; it can only transfer MSI/MSI-X from downstream devices.
Add a quirk to prevent use of MSI/MSI-X in RC mode.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Factor out Interrupt Message Number lookup from the MSI/MSI-X interrupt
setup. One side effect is that we only have to check once to see if we
have enough vectors for all the services. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Consolidate some repetitive comments so we can see the code better. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the AER case, the mask isn't strictly necessary because there are no
higher-order bits above the Interrupt Message Number, but using a #define
will make it possible to grep for it.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Extend the Cavium ThunderX ACS quirk to cover more device IDs and restrict
it to only Root Ports.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: changelog, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.12+
We do not want the common dma_configure() pathway to apply
indiscriminately to all devices, since there are plenty of buses which
do not have DMA capability, and if their child devices were used for
DMA API calls it would only be indicative of a driver bug. However,
there are a number of buses for which DMA is implicitly expected even
when not described by firmware - those we whitelist with an automatic
opt-in to dma_configure(), assuming that the DMA address space and the
physical address space are equivalent if not otherwise specified.
Commit 723288836628 ("of: restrict DMA configuration") introduced a
short-term fix by comparing explicit bus types, but this approach is far
from pretty, doesn't scale well, and fails to cope at all with bus
drivers which may be built as modules, like host1x. Let's refine things
by making that opt-in a property of the bus type, which neatly addresses
those problems and lets the decision of whether firmware description of
DMA capability should be optional or mandatory stay internal to the bus
drivers themselves.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make config_item_type structures const as they are either passed to a
function having the argument as const or stored in the const "ci_type"
field of a config_item structure.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The Cavium ThunderX (CN8XXX) family of PCIe Root Ports does not advertise
an ACS capability. However, the RTL internally implements similar
protection as if ACS had Request Redirection, Completion Redirection,
Source Validation, and Upstream Forwarding features enabled.
Change Cavium ACS capabilities quirk flags accordingly.
Fixes: b404bcfbf035 ("PCI: Add ACS quirk for all Cavium devices")
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: tidy changelog, comment, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.6+: b77d537d00d0: PCI: Apply Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
Add Tegra186 PCIe support. UPHY programming is performed by BPMP; PHY
enable calls are not required for Tegra186 PCIe.
Power partition ungate is done by BPMP powergate driver. The Tegra186
DT description must include a "power-domains" property, which results in
dev->pm_domain being set.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[bhelgaas: add "power-domains" reference]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
If interrupt reservation mode is enabled then the PCI/MSI interrupts must
be reactivated after early activation.
Make sure that all callers of pci_msi_create_irq_domain() have the
MSI_FLAG_MUST_REACTIVATE set when reservation mode is enabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Link: https://lkml.kernel.org/r/20171017075600.448649905@linutronix.de
Add support for allocating multiple MSIs at the same time, so that the
MSI_FLAG_MULTI_PCI_MSI flag can be added to the msi_domain_info structure.
Avoid storing the hwirq in the low 5 bits of the message data, as it is
used by the device. Also fix an endianness problem by using readl().
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Add support for ls1012a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The Tegra PCI host controller can generate configuration space accesses
with byte, word and dword granularity for devices. Only root ports can't
have their configuration space accessed in this way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add shutdown handler to cleanly turn off clocks. This will help in cases of
kexec where in a new kernel can boot abruptly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
When checking to see if a PCI slot can safely be reset, we previously
checked to see if any of the children had their PCI_DEV_FLAGS_NO_BUS_RESET
flag set.
Some PCIe root port bridges do not behave well after a slot reset, and may
cause the device in the slot to become unusable.
Add a check for PCI_DEV_FLAGS_NO_BUS_RESET being set in the bridge device
to prevent the slot from being reset.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
When checking to see if a PCI bus can safely be reset, we previously
checked to see if any of the children had their PCI_DEV_FLAGS_NO_BUS_RESET
flag set. Children marked with that flag are known not to behave well
after a bus reset.
Some PCIe root port bridges also do not behave well after a bus reset,
sometimes causing the devices behind the bridge to become unusable.
Add a check for PCI_DEV_FLAGS_NO_BUS_RESET being set in the bridge device
to allow these bridges to be flagged, and prevent their secondary buses
from being reset.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Root ports of cn8xxx do not function after bus reset when used with some
e1000e and LSI HBA devices. Add a quirk to prevent bus reset on these root
ports.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo and whitespaces]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Commit 769b461fc0c0 ("arm64: PCI: Drop DT IRQ allocation from
pcibios_alloc_irq()") was assuming all PCI host controller drivers had been
converted to use ->map_irq(), but that wasn't the case: pci-aardvark had
not been converted. Due to this, it broke the support for legacy PCI
interrupts when using the pci-aardvark driver (used on Marvell Armada 3720
platforms).
In order to fix this, we make sure the ->map_irq and ->swizzle_irq fields
of pci_host_bridge are properly filled in.
Fixes: 769b461fc0c0 ("arm64: PCI: Drop DT IRQ allocation from pcibios_alloc_irq()")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.13+
In the restore path, we previously read PCI_SRIOV_VF_OFFSET and
PCI_SRIOV_VF_STRIDE before restoring PCI_SRIOV_CTRL_ARI:
pci_restore_state
pci_restore_iov_state
sriov_restore_state
pci_iov_set_numvfs
pci_read_config_word(... PCI_SRIOV_VF_OFFSET, &iov->offset)
pci_read_config_word(... PCI_SRIOV_VF_STRIDE, &iov->stride)
pci_write_config_word(... PCI_SRIOV_CTRL, iov->ctrl)
But per SR-IOV r1.1, sec 3.3.3.5, the device can use PCI_SRIOV_CTRL_ARI to
determine PCI_SRIOV_VF_OFFSET and PCI_SRIOV_VF_STRIDE. Therefore, this
path, which is used for suspend/resume and AER recovery, can corrupt
iov->offset and iov->stride.
Since the iov state is associated with the device, not the driver, if we
reload the driver, it will use the the corrupted data, which may cause
crashes like this:
kernel BUG at drivers/pci/iov.c:157!
RIP: 0010:pci_iov_add_virtfn+0x2eb/0x350
Call Trace:
pci_enable_sriov+0x353/0x440
ixgbe_pci_sriov_configure+0xd5/0x1f0 [ixgbe]
sriov_numvfs_store+0xf7/0x170
dev_attr_store+0x18/0x30
sysfs_kf_write+0x37/0x40
kernfs_fop_write+0x120/0x1b0
vfs_write+0xb5/0x1a0
SyS_write+0x55/0xc0
Restore PCI_SRIOV_CTRL_ARI before calling pci_iov_set_numvfs(), then
restore the rest of PCI_SRIOV_CTRL (which may set PCI_SRIOV_CTRL_VFE)
afterwards.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
[bhelgaas: changelog, add comment, also clear ARI if necessary]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
When creating virtual functions, create the "virtfn%u" and "physfn" links
in sysfs *before* attaching the driver instead of after. When we attach
the driver to the new virtual network interface first, there is a race when
the driver attaches to the new sends out an "add" udev event, and the
network interface naming software (biosdevname or systemd, for example)
tries to look at these links.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Expose the SR-IOV device offset, stride, and VF device ID via sysfs to make
it easier for userspace applications to consume them.
Signed-off-by: Filippo Sironi <sironi@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit d7bd554f27c942e6b8b54100b4044f9be1038edf.
It turns out that Tegra20 has a bug in the implementation of the MSI
target address register (which is worked around by the existence of the
struct tegra_pcie_soc.msi_base_shift parameter) that restricts the MSI
target memory to the lower 32 bits of physical memory on that particular
generation. The offending patch causes a regression on TrimSlice, which
is a Tegra20-based device and has a PCI network interface card.
An initial, simpler fix was to change the MSI target address for Tegra20
only, but it was pointed out that the offending commit also prevents the
use of 32-bit only MSI capable devices, even on later chips. Technically
this was never guaranteed to work with the prior code in the first place
because the allocated page could have resided beyond the 4 GiB boundary,
but it is still possible that this could've introduced a regression.
The proper fix that was settled on is to select a fixed address within
the lowest 32 bits of physical address space that is otherwise unused,
but testing of that patch has provided mixed results that are not fully
understood yet.
Given all of the above and the relative urgency to get this fixed in
v4.13, revert the offending commit until a universal fix is found.
Fixes: d7bd554f27c9 ("PCI: tegra: Do not allocate MSI target memory")
Reported-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reported-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.13.x
Some implementations of the Synopsys DesignWare PCIe controller implement
a so-called ECAM shift mode, which allows a static memory window to be
configured that covers the configuration space of the entire bus range.
Usually, when the firmware performs all the low level configuration that is
required to expose this controller in a fully ECAM compatible manner, we
can simply describe it as "pci-host-ecam-generic" and be done with it.
However, in some cases (e.g., the Marvell Armada 80x0 as well as the
Socionext SynQuacer Soc), the IP was synthesized with an ATU window
granularity that does not allow the first bus to be mapped in a way that
prevents the device on the downstream port from appearing more than once,
and so we still need special handling in software to drive this static
almost-ECAM configuration.
So extend the pci-host-generic driver so it can support these controllers
as well, by adding special config space accessors that take the above quirk
into account.
Note that, unlike most drivers for this IP, this driver does not expose a
fake bridge device at B/D/F 00:00.0. There is no point in doing so, given
that this is not a true bridge, and does not require any windows to be
configured in order for the downstream device to operate correctly.
Omitting it also prevents the PCI resource allocation routines from handing
out BAR space to it unnecessarily.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[bhelgaas: factor out pci_dw_valid_device(), add pci_dw_ecam_map_bus() and
use generic read/write functions]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
The structure event_regs is local to the source and does not need to be in
global scope, so make it static.
Cleans up sparse warning:
symbol 'event_regs' was not declared. Should it be static
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Cache the VF device ID in the SR-IOV structure and use it instead of
reading it over and over from the PF config space capability.
Signed-off-by: Filippo Sironi <sironi@amazon.de>
[bhelgaas: rename to "vf_device" to match pci_dev->device]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Ensure only valid Kconfig configurations for PCI_REALLOC_ENABLE_AUTO. This
is done by selecting PCI_IOV, which is required by PCI_REALLOC_ENABLE_AUTO
to work.
Signed-off-by: Sascha El-Sharkawy <elscha@sse.uni-hildesheim.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The last caller of __pci_reset_function() has been removed. Remove the
function as well.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "reset" argument passed to pci_iov_add_virtfn() and
pci_iov_remove_virtfn() is always zero since 46cb7b1bd86f ("PCI: Remove
unused SR-IOV VF Migration support")
Remove the argument together with the associated code.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Make this const as it not modified in the file referencing it. It is only
stored in a const field 'type' of a device structure. Also, add const to
the variable declaration in the header file.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This PCI host bridge from V3 Semiconductor needs no further
introduction. An ancient driver for it has been sitting in
arch/arm/mach-integrator/pci_v3.* since before v2.6.12 and the
initial migration to git.
But we need to get the drivers out of arch/arm/* and get proper handling of
the old drivers, rewrite and clean up so the PCI maintainer can control the
mass of drivers without having to run all over the kernel. We also switch
swiftly to all the new infrastructure found in the PCI hosts as of late.
Some code is preserved so I have added an extensive list of authors in the
top comment section.
This driver probes with the following result:
OF: PCI: host bridge /pciv3@62000000 ranges:
OF: PCI: No bus range found for /pciv3@62000000, using [bus 00-ff]
OF: PCI: IO 0x60000000..0x6000ffff -> 0x00000000
OF: PCI: MEM 0x40000000..0x4fffffff -> 0x40000000
OF: PCI: MEM 0x50000000..0x5fffffff -> 0x50000000
pci-v3-semi 62000000.pciv3: initialized PCI V3 Integrator/AP integration
pci-v3-semi 62000000.pciv3: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [mem 0x50000000-0x5fffffff pref]
pci-v3-semi 62000000.pciv3: parity error interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
(repeats a few times)
pci 0000:00:09.0: [1011:0024] type 01 class 0x060400
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci 0000:00:0b.0: [8086:1229] type 00 class 0x020000
pci 0000:00:0b.0: reg 0x10: [mem 0x00000000-0x00000fff pref]
pci 0000:00:0b.0: reg 0x14: [io 0x0000-0x001f]
pci 0000:00:0b.0: reg 0x18: [mem 0x00000000-0x000fffff]
pci 0000:00:0b.0: reg 0x30: [mem 0x00000000-0x000fffff pref]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0c.0: [5333:8811] type 00 class 0x030000
pci 0000:00:0c.0: reg 0x10: [mem 0x00000000-0x03ffffff]
pci 0000:00:0c.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
pci 0000:00:0c.0: vgaarb: VGA device added: decodes=io+mem,owns=io,locks=none
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:00:0c.0: BAR 0: assigned [mem 0x40000000-0x43ffffff]
pci 0000:00:0b.0: BAR 2: assigned [mem 0x44000000-0x440fffff]
pci 0000:00:0b.0: BAR 6: assigned [mem 0x50000000-0x500fffff pref]
pci 0000:00:0c.0: BAR 6: assigned [mem 0x50100000-0x5010ffff pref]
pci 0000:00:0b.0: BAR 0: assigned [mem 0x50110000-0x50110fff pref]
pci 0000:00:0b.0: BAR 1: assigned [io 0x1000-0x101f]
pci 0000:00:09.0: PCI bridge to [bus 01]
pci 0000:00:0b.0: Firmware left e100 interrupts enabled; disabling
(...)
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:00:0b.0: enabling device (0146 -> 0147)
e100 0000:00:0b.0 eth0: addr 0x50110000, irq 31, MAC addr 00:08:c7:99:d2:57
> lspci
00:0b.0 Class 0200: 8086:1229
00:09.0 Class 0604: 1011:0024
00:0c.0 Class 0300: 5333:8811
> cat /proc/iomem
40000000-4fffffff : V3 PCI NON-PRE-MEM
40000000-43ffffff : 0000:00:0c.0
44000000-440fffff : 0000:00:0b.0
44000000-440fffff : e100
50000000-5fffffff : V3 PCI PRE-MEM
50000000-500fffff : 0000:00:0b.0
50100000-5010ffff : 0000:00:0c.0
50110000-50110fff : 0000:00:0b.0
50110000-50110fff : e100
61000000-61ffffff : /pciv3@62000000
62000000-6200ffff : /pciv3@62000000
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bhelgaas: fold in %pR fixes from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20171011140224.3770968-1-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
