This patch addresses an issue seen on 82580 in which the MDICNFG
register will be reset during a single function reset and as a
result we will be unable to communicate with the PHY. To correct
the issue, added a call to reset_mdicnfg just prior to the first
access of the MDICNFG register in sgnii_uses_mdio.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC-PHY interconnect register set on ICH/PCH parts is accessed through
a peephole mechanism by writing an offset to a CSR register. The offset
for the interconnect's half-duplex control register (which is used in a
jumbo frame workaround for 82579) is incorrect.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for esd's USB high speed
CAN interface. The driver supports devices with
multiple CAN interfaces.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My fine DisplayPort output was getting ST dithering forever after
having had the LVDS enabled at one point.
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a hwmon driver for package level thermal control. The driver
dumps package level thermal information through sysfs interface so that upper
level application (e.g. lm_sensor) can retrive the information.
Instead of having the package level hwmon code in coretemp, I write a seperate
driver pkgtemp because:
First, package level thermal sensors include not only sensors for each core,
but also sensors for uncore, memory controller or other components in the
package. Logically it will be clear to have a seperate hwmon driver for package
level hwmon to monitor wider range of sensors in a package. Merging package
thermal driver into core thermal driver doesn't make sense and may mislead.
Secondly, merging the two drivers together may cause coding mess. It's easier
to include various package level sensors info if more sensor information is
implemented. Coretemp code needs to consider a lot of legacy machine cases.
Pkgtemp code only considers platform starting from Sandy Bridge.
On a 1Sx4Cx2T Sandy Bridge platform, lm-sensors dumps the pkgtemp and coretemp:
pkgtemp-isa-0000
Adapter: ISA adapter
physical id 0: +33.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0002
Adapter: ISA adapter
Core 2: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0003
Adapter: ISA adapter
Core 3: +32.0°C (high = +79.0°C, crit = +99.0°C)
[ hpa: folded v3 patch removing improper global variable "SHOW" ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-3-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not warn unnecessarily
UBI: do not print message about corruptes PEBs if we have none of them
UBI: improve delete-compatible volumes handling
UBI: fix error message and compilation warnings
UBI: generate random image_seq when formatting MTD devices
UBI: improve ECC error message
UBI: improve corrupted flash handling
UBI: introduce eraseblock counter variables
UBI: introduce a new IO return code
UBI: simplify IO error codes
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
ARM: AMBA: Add pclk support to AMBA bus infrastructure
ARM: 6278/2: fix regression in RealView after the introduction of pclk
ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
ARM: 6244/1: mmci: add variant data and default MCICLOCK support
ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
ARM: 6274/1: add global control registers definition header file for nuc900
mx2_camera: fix type of dma buffer virtual address pointer
mx2_camera: Add soc_camera support for i.MX25/i.MX27
arm/imx/gpio: add spinlock protection
ARM: Add support for the LPC32XX arch
ARM: LPC32XX: Arch config menu supoport and makefiles
ARM: LPC32XX: Phytec 3250 platform support
ARM: LPC32XX: Misc support functions
ARM: LPC32XX: Serial support code
ARM: LPC32XX: System suspend support
ARM: LPC32XX: GPIO, timer, and IRQ drivers
ARM: LPC32XX: Clock driver
...
When transitioning a QP to the error state, in progress RWQEs need to
be marked complete. This also involves releasing the reference count
to the memory regions referenced in the SGEs. The locking in the
receive packet processing wasn't sufficient to prevent qib_error_qp()
from modifying the r_sge state at the same time, thus leading to
kernel panics.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't processes too many packets without allowing other IRQ functions
a chance to run. Otherwise, there is a chance of getting a "soft
lockup" messages and poor application response times.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Up to now, we have set the number of available user contexts based on
the number of hardware contexts which is set according to the number
of available CPUs. This was fine since most CPUs had a power of two
number of cores and the chip supported 4, 8, or 16 user contexts. Now
that some systems have 12 cores, the default isn't optimal and should
be set to 12 even though 16 hardware contexts need to be enabled.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes up a brace warning found by the checkpatch.pl tool
Signed-off-by: Neal Buckendahl <nealb001@tbcnet.com>
Signed-off-by: Dave Jones <davej@redhat.com>
and fix the broken case if a core's frequency depends on others.
trace_power_frequency was only implemented in a rather ungeneric way
in acpi-cpufreq driver's target() function only.
-> Move the call to trace_power_frequency to
cpufreq.c:cpufreq_notify_transition() where CPUFREQ_POSTCHANGE
notifier is triggered.
This will support power frequency tracing by all cpufreq drivers
trace_power_frequency did not trace frequency changes correctly when
the userspace governor was used or when CPU cores' frequency depend
on each other.
-> Moving this into the CPUFREQ_POSTCHANGE notifier and pass the cpu
which gets switched automatically fixes this.
Robert Schoene provided some important fixes on top of my initial
quick shot version which are integrated in this patch:
- Forgot some changes in power_end trace (TP_printk/variable names)
- Variable dummy in power_end must now be cpu_id
- Use static 64 bit variable instead of unsigned int for cpu_id
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: davej@redhat.com
CC: arjan@infradead.org
CC: linux-kernel@vger.kernel.org
CC: robert.schoene@tu-dresden.de
Tested-by: robert.schoene@tu-dresden.de
Signed-off-by: Dave Jones <davej@redhat.com>
For UP systems this is not required, and results in a more consistent
sample interval.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jocelyn Falempe <jocelyn.falempe@motorola.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
lock_policy_rwsem_* and unlock_policy_rwsem_* functions are scheduled
to be unexported when 2.6.33. Now there are no other callers of them
out of cpufreq.c, unexport them and make them static.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Make simpler to read and call.
*** v3 - Always call when powersave_bias is enabled.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Dave Jones <davej@redhat.com>
395913d0b1db37092ea3d9d69b832183b1dd84c5 ("[CPUFREQ] remove rwsem lock
from CPUFREQ_GOV_STOP call (second call site)") is not needed, because
there is no rwsem lock in cpufreq_ondemand and cpufreq_conservative
anymore. Lock should not be released until the work done.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=1594
Signed-off-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Dave Jones <davej@redhat.com>
We don't need a dev_warn when we exceed a thermal or power limit as
we'll handle it appropriately by clamping down on the CPU, GPU or both
as needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
NR_IRQS may be as low as 16, causing a (harmless?) buffer overflow in
pcmcia_setup_isa_irq():
static u8 pcmcia_used_irq[NR_IRQS];
...
if ((try < 32) && pcmcia_used_irq[irq])
continue;
This is read-only, so if this address would be non-zero, it would just
mean we would not attempt an IRQ >= NR_IRQS -- which would fail anyway!
And as request_irq() fails for an irq >= NR_IRQS, the setting code path:
pcmcia_used_irq[irq]++;
is never reached as well.
Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
CC: stable@kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Fortify the interface to not accept negative values, remove
memctrl_int_store() as a result. Also, sanitize bandwidth setting by
making the argument a simple u32 instead of strange u32 pointer being
passed around for no obvious reason. Then, fix error handling and teach
it to return proper error values. Finally, make code more readable,
simplify debug messages.
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
The correct check is to verify whether in high range we're below 4GB
and not to extract the DctSelBaseAddr again. See "2.8.5 Routing DRAM
Requests" in the F10h BKDG.
Cc: <stable@kernel.org> # .32.x .33.x .34.x
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Switch to reusing the mcheck core's machine check polling mechanism
instead of duplicating functionality by using the EDAC polling routine.
Correct formatting while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
All F2x110-related bit defines are used at only one place so replace
them with simple BIT() macros.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
This option differs from EDAC_DEBUG only by printing the file and
line of where the debug statement is placed, which contains unneeded
information. So remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Remove the two syndrome extraction macros and add a single function
which does the same thing but with proper typechecking. While at it,
make sure to cache ECC syndrome size and dump it in debug output.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Size for PMIC read/write command is byte, while it is DWORD for other
IPC commands.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: ALan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Data is 2-byte per entry for PMIC read-modify-update command.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Don't pass more bytes in the command length field than we filled.
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
some messages take 4 bytes, but only fill 3 bytes....
this patch makes sure that whatever we send to the SCU is zeroed first
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The stack buffer for IPC messages was 16 bytes, limiting messages to a
size of 4 (each message is 32 bit).
However, the touch screen driver is trying to send messages of size 5....
(AC: Set to 20 bytes having checked the max size allowed)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This provides an architecture level board identify function to replace the
cpuid direct usage
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The firmware of production devices does not support this interface so this
is dead code.
Signed-off-by: Sreedhara DS <sreedhara.ds@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Changes to work on bothMmoorestown and Medfield
New pci id added for Medfield
Return type of ipc_data_readl chnaged from u8 to u32
Signed-off-by: Sreedhara DS <sreedhara.ds@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Intel SCU message formats depend upon the processor type. Replace the
module option with automatic detection of the processor type.
Signed-off-by: Sreedhara DS <sreedhara.ds@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
My .config contains ACER_WMI=m. On SPARC. That does not make sense.
Restrict the x86 platform driver menu to x86.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
- Set Kconfig option default n
- Only allow root to read/write io file (sever bug!)
- Introduce write support module param -> default off
- Properly clean up if any debugfs files cannot be created
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: mjg59@srcf.ucam.org
CC: platform-driver-x86@vger.kernel.org
CC: linux-acpi@vger.kernel.org
CC: astarikovskiy@suse.de
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Make dell_laptop_i8042_filter() static as it's used only in dell-laptop.c
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch includes below fixes:
1. return -ENOMEM instead of 0 if input_allocate_device fail.
2. fix wrong goto if sparse_keymap_setup fail.
3. fix wrong goto if input_register_device fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
backlight is needlessly defined global.
This patch makes the symbol static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add support for Toshiba Illumination. This is a set of LEDs installed on
some Toshiba laptops. It is controlled through ACPI, the commands has been
found through reverse engineering. It has been tested on a Toshiba Qosmio
G50-122.
Signed-off-by: Pierre Ducroquet <pinaraf@pinaraf.info>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
