Jose Abreu says:
====================
net: stmmac: Enable Flow Control
I don't know of any specific reason why Flow Control is off by default but
do let me know if there is any.
Tested in B2B between XGMAC2 and GMAC5.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
By default Flow Control feature is not being enabled in stmmac.
This is a useful feature that can prevent loss of packets and now that
XGMAC already supports it (along with GMAC and QoS) it makes sense to
activate it.
Switch the module parameter to FLOW_AUTO so that Flow Control is
activated.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish the implementation of Flow Control feature. In order for it to
work correctly we need to set EHFC bit and the correct threshold values
for activating and deactivating it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Handle init flow failures properly in iwlwifi driver, from Shahar S
Matityahu.
2) mac80211 TXQs need to be unscheduled on powersave start, from Felix
Fietkau.
3) SKB memory accounting fix in A-MDSU aggregation, from Felix Fietkau.
4) Increase RCU lock hold time in mlx5 FPGA code, from Saeed Mahameed.
5) Avoid checksum complete with XDP in mlx5, also from Saeed.
6) Fix netdev feature clobbering in ibmvnic driver, from Thomas Falcon.
7) Partial sent TLS record leak fix from Jakub Kicinski.
8) Reject zero size iova range in vhost, from Jason Wang.
9) Allow pending work to complete before clcsock release from Karsten
Graul.
10) Fix XDP handling max MTU in thunderx, from Matteo Croce.
11) A lot of protocols look at the sa_family field of a sockaddr before
validating it's length is large enough, from Tetsuo Handa.
12) Don't write to free'd pointer in qede ptp error path, from Colin Ian
King.
13) Have to recompile IP options in ipv4_link_failure because it can be
invoked from ARP, from Stephen Suryaputra.
14) Doorbell handling fixes in qed from Denis Bolotin.
15) Revert net-sysfs kobject register leak fix, it causes new problems.
From Wang Hai.
16) Spectre v1 fix in ATM code, from Gustavo A. R. Silva.
17) Fix put of BROPT_VLAN_STATS_PER_PORT in bridging code, from Nikolay
Aleksandrov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (111 commits)
socket: fix compat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW
tcp: tcp_grow_window() needs to respect tcp_space()
ocelot: Clean up stats update deferred work
ocelot: Don't sleep in atomic context (irqs_disabled())
net: bridge: fix netlink export of vlan_stats_per_port option
qed: fix spelling mistake "faspath" -> "fastpath"
tipc: set sysctl_tipc_rmem and named_timeout right range
tipc: fix link established but not in session
net: Fix missing meta data in skb with vlan packet
net: atm: Fix potential Spectre v1 vulnerabilities
net/core: work around section mismatch warning for ptp_classifier
net: bridge: fix per-port af_packet sockets
bnx2x: fix spelling mistake "dicline" -> "decline"
route: Avoid crash from dereferencing NULL rt->from
MAINTAINERS: normalize Woojung Huh's email address
bonding: fix event handling for stacked bonds
Revert "net-sysfs: Fix memory leak in netdev_register_kobject"
rtnetlink: fix rtnl_valid_stats_req() nlmsg_len check
qed: Fix the DORQ's attentions handling
qed: Fix missing DORQ attentions
...
The patch a6dbe4427559 ("vt: perform safe console erase in the right
order") introduced a bug. The conditional do_update_region() was
replaced by a call to update_region() that does contain the conditional
already, but with unwanted extra side effects such as restoring the cursor
drawing.
In order to reproduce the bug:
- use framebuffer console with the AMDGPU driver
- type "links" to start the console www browser
- press 'q' and space to exit links
Now the cursor will be permanently visible in the center of the
screen. It will stay there until something overwrites it.
The bug goes away if we change update_region() back to the conditional
do_update_region().
[ nico: reworded changelog ]
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Cc: stable@vger.kernel.org
Fixes: a6dbe4427559 ("vt: perform safe console erase in the right order")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`ni6501_alloc_usb_buffers()` is called from `ni6501_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `ni6501_detach()` will be called from the core comedi
module code to clean up. `ni6501_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already beed freed, leading to a
double-free error. Fix it bu removing the call to
`kfree(devpriv->usb_rx_buf)` from `ni6501_alloc_usb_buffers()`, relying
on `ni6501_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If `ni6501_auto_attach()` returns an error, the core comedi module code
will call `ni6501_detach()` to clean up. If `ni6501_auto_attach()`
successfully allocated the comedi device private data, `ni6501_detach()`
assumes that a `struct mutex mut` contained in the private data has been
initialized and uses it. Unfortunately, there are a couple of places
where `ni6501_auto_attach()` can return an error after allocating the
device private data but before initializing the mutex, so this
assumption is invalid. Fix it by initializing the mutex just after
allocating the private data in `ni6501_auto_attach()` before any other
errors can be retturned. Also move the call to `usb_set_intfdata()`
just to keep the code a bit neater (either position for the call is
fine).
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=cf4f2b6c24aff0a3edf6>:
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
usb 1-1: string descriptor 0 read error: -71
comedi comedi0: Wrong number of endpoints
ni6501 1-1:0.233: driver 'ni6501' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 585 Comm: kworker/0:3 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xfe/0x12b0 kernel/locking/mutex.c:1072
ni6501_detach+0x5b/0x110 drivers/staging/comedi/drivers/ni_usb6501.c:567
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+cf4f2b6c24aff0a3edf6@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have two Dell laptops which have the codec 10ec0236 and 10ec0256
respectively, the headset mic on them can't work, need to apply the
quirk of ALC255_FIXUP_DELL1_MIC_NO_PRESENCE. So adding their pin
configurations in the pin quirk table.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Inline assembly code changed in this patch should really use "Q"
constraint "Memory reference without index register and with short
displacement". The kernel build with kasan instrumentation enabled
might occasionally break otherwise (due to stack instrumentation).
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The audio configuration is only valid if the HDMI codec has been
properly set up. Do not attempt to set up audio before that happens
because it causes a division by zero.
Note that this is only problematic on Tegra20 and Tegra30. Later chips
implement the division instructions which return zero when dividing by
zero and don't throw an exception.
Fixes: db5adf4d6dce ("drm/tegra: hdmi: Fix audio to work with any pixel clock rate")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It looks like the new socket options only work correctly
for native execution, but in case of compat mode fall back
to the old behavior as we ignore the 'old_timeval' flag.
Rework so we treat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW the
same way in compat and native 32-bit mode.
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Fixes: a9beb86ae6e5 ("sock: Add SO_RCVTIMEO_NEW and SO_SNDTIMEO_NEW")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, tcp_grow_window() correctly tests if enough room
is present before attempting to increase tp->rcv_ssthresh,
but does not prevent it to grow past tcp_space()
This is causing hard to debug issues, like failing
the (__tcp_select_window(sk) >= tp->rcv_wnd) test
in __tcp_ack_snd_check(), causing ACK delays and possibly
slow flows.
Depending on tcp_rmem[2], MTU, skb->len/skb->truesize ratio,
we can see the problem happening on "netperf -t TCP_RR -- -r 2000,2000"
after about 60 round trips, when the active side no longer sends
immediate acks.
This bug predates git history.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciocoi Radulescu says:
====================
dpaa2-eth: Add flow steering support without masking
On DPAA2 platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't offer
flow steering capabilities at all on these platforms.
Introduce a limited support for flow steering, where we only
allow ethtool rules that share a common key (i.e. have the same
header fields). If a rule with a new composition key is wanted,
the user must first manually delete all previous rules.
First patch fixes a minor bug, the next two cleanup and prepare
the code and the last one introduces the actual FS support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't
offer flow steering capabilities at all on these platforms,
since our driver implementation configured a "comprehensive"
FS key (containing all supported header fields), with masks
used to ignore the fields not present in the rules provided
by the user.
We now allow ethtool rules that share a common key (i.e. have
the same header fields). The FS key is now kept in the driver
private data and initialized when the first rule is added to
an empty table, rather than at probe time. If a rule with a new
composition key is wanted, the user must first manually delete
all previous rules.
When building a FS table entry to pass to firmware, we still use
the old building algorithm, which assumes an all-supported-fields
key, and later collapse the fields which aren't actually needed.
Masked rules are not supported; if provided, the mask value
will be ignored. For firmware versions older than MC10.7.0
(that only offer the legacy ABIs for configuring distribution
keys) flow steering without masking support remains unavailable.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an internal id bitfield to uniquely identify header fields
supported by the Rx distribution keys. For the hash key, add a
conversion from the RXH_* bitmask provided by ethtool to the internal
ids.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two macros to simplify reading DPNI options.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the Rx flow classification enable flag only if key config
operation is successful.
Fixes 3f9b5c9 ("dpaa2-eth: Configure Rx flow classification key")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nfp_flower_copy_pre_actions function introduces a case statement with
an intentional fallthrough. However, this generates a warning if built
with the -Wimplicit-fallthrough flag.
Remove the warning by adding a fall through comment.
Fixes: 1c6952ca587d ("nfp: flower: generate merge flow rule")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the introduction of the vlan_stats_per_port option the netlink
export of it has been broken since I made a typo and used the ifla
attribute instead of the bridge option to retrieve its state.
Sysfs export is fine, only netlink export has been affected.
Fixes: 9163a0fc1f0c0 ("net: bridge: add support for per-port vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
bnx2x: Support for timestamping in P2P mode.
The patch series adds driver support for timestamping the ptp packets
in peer-delay (P2P) mode.
- Patch (1) performs the code cleanup.
- Patch (2) adds the required implementation.
Please consider applying it 'net-next' tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for detecting the P2P (peer-to-peer) event packets.
This is required for timestamping the PTP packets in peer delay mode.
Unmask the below bits (set to 0) for device to detect the p2p packets.
NIG_REG_P0/1_LLH_PTP_PARAM_MASK
NIG_REG_P0/1_TLLH_PTP_PARAM_MASK
bit 1 - IPv4 DA 1 of 224.0.0.107.
bit 3 - IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B.
bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
NIG_REG_P0/1_LLH_PTP_RULE_MASK
NIG_REG_P0/1_TLLH_PTP_RULE_MASK
bit 2 - {IPv4 DA 1; UDP DP 0}
bit 6 - MAC Ethertype 0 of 0x88F7.
bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch performs code cleanup by defining macros for the ptp-timestamp
filters.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We find that sysctl_tipc_rmem and named_timeout do not have the right minimum
setting. sysctl_tipc_rmem should be larger than zero, like sysctl_tcp_rmem.
And named_timeout as a timeout setting should be not less than zero.
Fixes: cc79dd1ba9c10 ("tipc: change socket buffer overflow control to respect sk_rcvbuf")
Fixes: a5325ae5b8bff ("tipc: add name distributor resiliency queue")
Signed-off-by: Jie Liu <liujie165@huawei.com>
Reported-by: Qiang Ning <ningqiang1@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the link FSM, when a link endpoint got RESET_MSG (- a
traditional one without the stopping bit) from its peer, it moves to
PEER_RESET state and raises a LINK_DOWN event which then resets the
link itself. Its state will become ESTABLISHING after the reset event
and the link will be re-established soon after this endpoint starts to
send ACTIVATE_MSG to the peer.
There is no problem with this mechanism, however the link resetting has
cleared the link 'in_session' flag (along with the other important link
data such as: the link 'mtu') that was correctly set up at the 1st step
(i.e. when this endpoint received the peer RESET_MSG). As a result, the
link will become ESTABLISHED, but the 'in_session' flag is not set, and
all STATE_MSG from its peer will be dropped at the link_validate_msg().
It means the link not synced and will sooner or later face a failure.
Since the link reset action is obviously needed for a new link session
(this is also true in the other situations), the problem here is that
the link is re-established a bit too early when the link endpoints are
not really in-sync yet. The commit forces a resync as already done in
the previous commit 91986ee166cf ("tipc: fix link session and
re-establish issues") by simply varying the link 'peer_session' value
at the link_reset().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_reorder_vlan_header() should move XDP meta data with ethernet header
if XDP meta data exists.
Fixes: de8f3a83b0a0 ("bpf: add meta pointer for direct access")
Signed-off-by: Yuya Kusakabe <yuya.kusakabe@gmail.com>
Signed-off-by: Takeru Hayasaka <taketarou2@gmail.com>
Co-developed-by: Takeru Hayasaka <taketarou2@gmail.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/xen-netfront.c: In function ‘netback_changed’:
drivers/net/xen-netfront.c:2038:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dev->state == XenbusStateClosed)
^
drivers/net/xen-netfront.c:2041:2: note: here
case XenbusStateClosing:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arg is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/atm/lec.c:715 lec_mcast_attach() warn: potential spectre issue 'dev_lec' [r] (local cap)
Fix this by sanitizing arg before using it to index dev_lec.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routine ptp_classifier_init() uses an initializer for an
automatic struct type variable which refers to an __initdata
symbol. This is perfectly legal, but may trigger a section
mismatch warning when running the compiler in -fpic mode, due
to the fact that the initializer may be emitted into an anonymous
.data section thats lack the __init annotation. So work around it
by using assignments instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes: 8626c56c8279 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Magnus Karlsson says:
====================
This patch set fixes one bug and removes two dependencies on Linux
kernel headers from the XDP socket code in libbpf. A number of people
have pointed out that these two dependencies make it hard to build the
XDP socket part of libbpf without any kernel header dependencies. The
two removed dependecies are:
* Remove the usage of likely and unlikely (compiler.h) in xsk.h. It
has been reported that the use of these actually decreases the
performance of the ring access code due to an increase in
instruction cache misses, so let us just remove these.
* Remove the dependency on barrier.h as it brings in a lot of kernel
headers. As the XDP socket code only uses two simple functions from
it, we can reimplement these. As a bonus, the new implementation is
faster as it uses the same barrier primitives as the kernel does
when the same code is compiled there. Without this patch, the user
land code uses lfence and sfence on x86, which are unnecessarily
harsh/thorough.
In the process of removing these dependencies a missing barrier
function for at least PPC64 was discovered. For a full explanation on
the missing barrier, please refer to patch 1. So the patch set now
starts with two patches fixing this. I have also added a patch at the
end removing this full memory barrier for x86 only, as it is not
needed there.
Structure of the patch set:
Patch 1-2: Adds the missing barrier function in kernel and user space.
Patch 3-4: Removes the dependencies
Patch 5: Optimizes the added barrier from patch 2 so that it does not
do unnecessary work on x86.
v2 -> v3:
* Added missing memory barrier in ring code
* Added an explanation on the three barriers we use in the code
* Moved barrier functions from xsk.h to libbpf_util.h
* Added comment on why we have these functions in libbpf_util.h
* Added a new barrier function in user space that makes it possible to
remove the full memory barrier on x86.
v1 -> v2:
* Added comment about validity of ARM 32-bit barriers.
Only armv7 and above.
/Magnus
====================
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The full memory barrier in the XDP socket rings on the consumer side
between the load of the data and the store of the consumer ring is
there to protect the store from being executed before the load of the
data. If this was allowed to happen, the producer might overwrite the
data field with a new entry before the consumer got the chance to read
it.
On x86, stores are guaranteed not to be reordered with older loads, so
it does not need a full memory barrier here. A compile time barrier
would be enough. This patch introdcues a new primitive in
libbpf_util.h that implements a new barrier type (libbpf_smp_rwmb)
hindering stores to be reordered with older loads. It is then used in
the XDP socket ring access code in libbpf to improve performance.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The use of smp_rmb() and smp_wmb() creates a Linux header dependency
on barrier.h that is unnecessary in most parts. This patch implements
the two small defines that are needed from barrier.h. As a bonus, the
new implementations are faster than the default ones as they default
to sfence and lfence for x86, while we only need a compiler barrier in
our case. Just as it is when the same ring access code is compiled in
the kernel.
Fixes: 1cad07884239 ("libbpf: add support for using AF_XDP sockets")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch removes the use of likely and unlikely in xsk.h since they
create a dependency on Linux headers as reported by several
users. There have also been reports that the use of these decreases
performance as the compiler puts the code on two different cache lines
instead of on a single one. All in all, I think we are better off
without them.
Fixes: 1cad07884239 ("libbpf: add support for using AF_XDP sockets")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The ring buffer code of XDP sockets is missing a memory barrier on the
consumer side between the load of the data and the write that signals
that it is ok for the producer to put new data into the buffer. On
architectures that does not guarantee that stores are not reordered
with older loads, the producer might put data into the ring before the
consumer had the chance to read it. As IA does guarantee this
ordering, it would only need a compiler barrier here, but there are no
primitives in barrier.h for this specific case (hinder writes to be ordered
before older reads) so I had to add a smp_mb() here which will
translate into a run-time synch operation on IA.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The ring buffer code of XDP sockets is missing a memory barrier on the
consumer side between the load of the data and the write that signals
that it is ok for the producer to put new data into the buffer. On
architectures that does not guarantee that stores are not reordered
with older loads, the producer might put data into the ring before the
consumer had the chance to read it. As IA does guarantee this
ordering, it would only need a compiler barrier here, but there are no
primitives in Linux for this specific case (hinder writes to be ordered
before older reads) so I had to add a smp_mb() here which will
translate into a run-time synch operation on IA.
Added a longish comment in the code explaining what each barrier in
the ring implementation accomplishes and what would happen if we
removed one of them.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Let's print btf id of map similar to the way we are printing it
for programs.
Sample output:
user@test# bpftool map -f
61: lpm_trie flags 0x1
key 20B value 8B max_entries 1 memlock 4096B
133: array name test_btf_id flags 0x0
key 4B value 4B max_entries 4 memlock 4096B
pinned /sys/fs/bpf/test100
btf_id 174
170: array name test_btf_id flags 0x0
key 4B value 4B max_entries 4 memlock 4096B
btf_id 240
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Let's move the final newline printing in show_map_close_plain() at
the end of the function because it looks correct and consistent with
prog.c. Also let's do related changes for the line which prints
pinned file name.
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add support for recently added BPF_PROG_TYPE_CGROUP_SYSCTL program type
and BPF_CGROUP_SYSCTL attach type.
Example of bpftool output with sysctl program from selftests:
# bpftool p load ./test_sysctl_prog.o /mnt/bpf/sysctl_prog type cgroup/sysctl
# bpftool p l
9: cgroup_sysctl name sysctl_tcp_mem tag 0dd05f81a8d0d52e gpl
loaded_at 2019-04-16T12:57:27-0700 uid 0
xlated 1008B jited 623B memlock 4096B
# bpftool c a /mnt/cgroup2/bla sysctl id 9
# bpftool c t
CgroupPath
ID AttachType AttachFlags Name
/mnt/cgroup2/bla
9 sysctl sysctl_tcp_mem
# bpftool c d /mnt/cgroup2/bla sysctl id 9
# bpftool c t
CgroupPath
ID AttachType AttachFlags Name
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Using %ld for printing out value of ptrdiff_t type is not portable
between 32-bit and 64-bit archs. This is causing compilation errors for
libbpf on 32-bit platform (discovered as part of an effort to integrate
libbpf into systemd ([0])). Proper formatter is %td, which is used in
this patch.
v2->v1:
- add Reported-by
- provide more context on how this issue was discovered
[0] https://github.com/systemd/systemd/pull/12151
Reported-by: Evgeny Vereshchagin <evvers@ya.ru>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
verifier.c uses BPF_CAST_CALL for casting bpf call except at one
place in jit_subprogs(). Let's use the macro for consistency.
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The helper function bpf_sock_ops_cb_flags_set() can be used to both
set and clear the sock_ops callback flags. However, its current
behavior is not consistent. BPF program may clear a flag if more than
one were set, or replace a flag with another one, but cannot clear all
flags.
This patch also updates the documentation to clarify the ability to
clear flags of this helper function.
Signed-off-by: Hoang Tran <hoang.tran@uclouvain.be>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds tests validating that VRF and BPF-LWT
encap work together well, as requested by David Ahern.
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch changes an error code for an admin queue
head overrun to use I40E_ERR_ADMIN_QUEUE_FULL instead
of I40E_ERR_QUEUE_EMPTY.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the problem with the driver being able to add only 7
multicast MAC address filters instead of 16. The problem is fixed by
changing the maximum number of MAC address filters to 16+1+1 (two extra
are needed because the driver uses 1 for unicast MAC address and 1 for
broadcast).
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Defined the advertised link mode field for 40000baseSR4_Full for
use with ethtool.
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
