[ Upstream commit 6c620a30515c494b5eeb3dc0e40d3220ea04c53b ]
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the nau8822 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is faster.
Set the MCLK at the right frequency, codec can properly use it to
generate 44.1 kHz I2S-FS.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5225ba9db112ec4ed67da5e4d8b72e618573955e ]
Early hardware did not support hardware handshaking on the UART, but
final production hardware did. When the hardware was updated the chip
select was changed to facilitate hardware handshaking on UART3. Fix the
ecspi2 pin mux to eliminate a pin conflict with UART3 and allow the
EEPROM to operate again.
Fixes: 4ce01ce36d ("arm64: dts: imx8mm-beacon: Enable RTS-CTS on UART3")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d1d030f00f3f3eea04017cbd50ffe44a2842ebc ]
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the wm8904 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is completely distorted.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfd04dd1c4b6c33afc2a934b957d71cf8ddd1539 ]
'regulator-compatible' is not a valid property according to
nxp,pca9450-regulator.yaml and causes the following warning:
DTC_CHK arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dtb
...
pmic@25: regulators:LDO1: Unevaluated properties are not allowed ('regulator-compatible' was unexpected)
Remove the invalid 'regulator-compatible' property.
Cc: Teresa Remmet <t.remmet@phytec.de>
Fixes: 88f7f6bcca ("arm64: dts: freescale: Add support for phyBOARD-Pollux-i.MX8MP")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee4e530bdde29a69c58656a919545251a782674e ]
The vendor kernel is using the GCC_USB4_DP_PHY_PRIM_BCR and
GCC_USB4_1_DP_PHY_PRIM_BCR resets for the USB4-USB3-DP QMP PHYs.
Update the primary USB-DP PHY node to match.
Fixes: 152d1faf1e ("arm64: dts: qcom: add SC8280XP platform")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221121085058.31213-15-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 18bba1843fc7f264f58c9345d00827d082f9c558 upstream.
Add the missing #include of asm/assembler.h, which is where the ldr_l
macro is defined.
Fixes: ff7a167961d1b97e ("arm64: efi: Execute runtime services from a dedicated stack")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff7a167961d1b97e0e205f245f806e564d3505e7 upstream.
With the introduction of PRMT in the ACPI subsystem, the EFI rts
workqueue is no longer the only caller of efi_call_virt_pointer() in the
kernel. This means the EFI runtime services lock is no longer sufficient
to manage concurrent calls into firmware, but also that firmware calls
may occur that are not marshalled via the workqueue mechanism, but
originate directly from the caller context.
For added robustness, and to ensure that the runtime services have 8 KiB
of stack space available as per the EFI spec, introduce a spinlock
protected EFI runtime stack of 8 KiB, where the spinlock also ensures
serialization between the EFI rts workqueue (which itself serializes EFI
runtime calls) and other callers of efi_call_virt_pointer().
While at it, use the stack pivot to avoid reloading the shadow call
stack pointer from the ordinary stack, as doing so could produce a
gadget to defeat it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a1ed98fe0f2e7669f0409de0f46f317b275f8be upstream.
After commit cf7f3f4fa9 ("clk: imx8mp: fix usb_root_clk parent"),
usb_root_clk is no longer for suspend clock so update dts accordingly
to use right bus clock and suspend clock.
Fixes: fb8587a2c1 ("arm64: dtsi: imx8mp: add usb nodes")
Cc: stable@vger.kernel.org # ed1f4ccfe947: clk: imx: imx8mp: add shared clk gate for usb suspend clk
Cc: stable@vger.kernel.org # v5.19+
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74c2f81054510d45b813548cb0a1c4ebf87cdd5f upstream.
The page table check trigger BUG_ON() unexpectedly when split hugepage:
------------[ cut here ]------------
kernel BUG at mm/page_table_check.c:119!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 7 PID: 210 Comm: transhuge-stres Not tainted 6.1.0-rc3+ #748
Hardware name: linux,dummy-virt (DT)
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : page_table_check_set.isra.0+0x398/0x468
lr : page_table_check_set.isra.0+0x1c0/0x468
[...]
Call trace:
page_table_check_set.isra.0+0x398/0x468
__page_table_check_pte_set+0x160/0x1c0
__split_huge_pmd_locked+0x900/0x1648
__split_huge_pmd+0x28c/0x3b8
unmap_page_range+0x428/0x858
unmap_single_vma+0xf4/0x1c8
zap_page_range+0x2b0/0x410
madvise_vma_behavior+0xc44/0xe78
do_madvise+0x280/0x698
__arm64_sys_madvise+0x90/0xe8
invoke_syscall.constprop.0+0xdc/0x1d8
do_el0_svc+0xf4/0x3f8
el0_svc+0x58/0x120
el0t_64_sync_handler+0xb8/0xc0
el0t_64_sync+0x19c/0x1a0
[...]
On arm64, pmd_leaf() will return true even if the pmd is invalid due to
pmd_present_invalid() check. So in pmdp_invalidate() the file_map_count
will not only decrease once but also increase once. Then in set_pte_at(),
the file_map_count increase again, and so trigger BUG_ON() unexpectedly.
Add !pmd_present_invalid() check in pmd_user_accessible_page() to fix the
problem.
Fixes: 42b2547137 ("arm64/mm: enable ARCH_SUPPORTS_PAGE_TABLE_CHECK")
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221121073608.4183459-1-liushixin2@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb9a85261e297292c4cc44b628c1373c996cedc2 upstream.
We currently guard REGSET_{SSVE, ZA} using ARM64_SVE for no good reason.
Both enumerations would be pointless without ARM64_SME and create two empty
entries in aarch64_regsets[] which would then become part of a process's
native regset view (they should be ignored though).
Switch to use ARM64_SME instead.
Fixes: e12310a0d3 ("arm64/sme: Implement ptrace support for streaming mode SVE registers")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221214135943.379-1-yuzenghui@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 730a11f982e61aaef758ab552dfb7c30de79e99b upstream.
Add check for the executable case in pud_user_accessible_page() too
like what we did for pte and pmd.
Fixes: 42b2547137 ("arm64/mm: enable ARCH_SUPPORTS_PAGE_TABLE_CHECK")
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Link: https://lore.kernel.org/r/20221122123137.429686-1-liushixin2@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dde62f0687c8856b6c0660066c7ee83a6a6f033 upstream.
Currently we reject an attempt to restore a SVE signal frame on a system
with SME but not SVE supported. This means that it is not possible to
disable streaming mode via signal return as this is configured via the
flags in the SVE signal context. Instead accept the signal frame, we will
require it to have a vector length of 0 specified and no payload since the
task will have no SVE vector length configured.
Fixes: 85ed24dad2 ("arm64/sme: Implement streaming SVE signal handling")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221223-arm64-fix-sme-only-v1-2-938d663f69e5@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f26cd7372160da2eba31061d7943348ab9f2c01d upstream.
Currently we only allocate space for SVE signal frames on systems that
support SVE, meaning that SME only systems do not allocate a signal frame
for streaming mode SVE state. Change the check so space is allocated if
either feature is supported.
Fixes: 85ed24dad2 ("arm64/sme: Implement streaming SVE signal handling")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221223-arm64-fix-sme-only-v1-3-938d663f69e5@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19e183b54528f11fafeca60fc6d0821e29ff281e upstream.
A subsequent fix for arm64 will use this parameter to parse the vma
information from the snapshot created by dump_vma_snapshot() rather than
traversing the vma list without the mmap_lock.
Fixes: 6dd8b1a0b6 ("arm64: mte: Dump the MTE tags in the core file")
Cc: <stable@vger.kernel.org> # 5.18.x
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Seth Jenkins <sethjenkins@google.com>
Suggested-by: Seth Jenkins <sethjenkins@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221222181251.1345752-3-catalin.marinas@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f4c549feb4ecca95ae9abb88887b941d196f83a upstream.
The MTE coredump code in arch/arm64/kernel/elfcore.c iterates over the
vma list without the mmap_lock held. This can race with another process
or userfaultfd concurrently modifying the vma list. Change the
for_each_mte_vma macro and its callers to instead use the vma snapshot
taken by dump_vma_snapshot() and stored in the cprm object.
Fixes: 6dd8b1a0b6 ("arm64: mte: Dump the MTE tags in the core file")
Cc: <stable@vger.kernel.org> # 5.18.x
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Seth Jenkins <sethjenkins@google.com>
Suggested-by: Seth Jenkins <sethjenkins@google.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221222181251.1345752-4-catalin.marinas@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 736eedc974eaafbf4360e0ea85fc892cea72a223 upstream.
Commit 16decce22e ("arm64: mte: Fix the stack frame size warning in
mte_dump_tag_range()") moved the temporary tag storage array from the
stack to slab but it also introduced an error in double freeing this
object. Remove the in-loop freeing.
Fixes: 16decce22e ("arm64: mte: Fix the stack frame size warning in mte_dump_tag_range()")
Cc: <stable@vger.kernel.org> # 5.18.x
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Seth Jenkins <sethjenkins@google.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221222181251.1345752-2-catalin.marinas@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 406504c7b0405d74d74c15a667cd4c4620c3e7a9 upstream.
A recent development on the EFI front has resulted in guests having
their page tables baked in the firmware binary, and mapped into the
IPA space as part of a read-only memslot. Not only is this legitimate,
but it also results in added security, so thumbs up.
It is possible to take an S1PTW translation fault if the S1 PTs are
unmapped at stage-2. However, KVM unconditionally treats S1PTW as a
write to correctly handle hardware AF/DB updates to the S1 PTs.
Furthermore, KVM injects an exception into the guest for S1PTW writes.
In the aforementioned case this results in the guest taking an abort
it won't recover from, as the S1 PTs mapping the vectors suffer from
the same problem.
So clearly our handling is... wrong.
Instead, switch to a two-pronged approach:
- On S1PTW translation fault, handle the fault as a read
- On S1PTW permission fault, handle the fault as a write
This is of no consequence to SW that *writes* to its PTs (the write
will trigger a non-S1PTW fault), and SW that uses RO PTs will not
use HW-assisted AF/DB anyway, as that'd be wrong.
Only in the case described in c4ad98e4b7 ("KVM: arm64: Assume write
fault on S1PTW permission fault on instruction fetch") do we end-up
with two back-to-back faults (page being evicted and faulted back).
I don't think this is a case worth optimising for.
Fixes: c4ad98e4b7 ("KVM: arm64: Assume write fault on S1PTW permission fault on instruction fetch")
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Regression-tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4a4175201014c0222f6bab1895a17b3d1b92f08 upstream.
The size of device tree node secmon (bl31_secmon_reserved) was
incorrect. It should be increased to 2MiB (0x200000).
The origin setting will cause some abnormal behavior due to
trusted-firmware-a and related firmware didn't load correctly.
The incorrect behavior may vary because of different software stacks.
For example, it will cause build error in some Yocto project because
it will check if there was enough memory to load trusted-firmware-a
to the reserved memory.
When mt8195-demo.dts sent to the upstream, at that time the size of
BL31 was small. Because supported functions and modules in BL31 are
basic sets when the board was under early development stage.
Now BL31 includes more firmwares of coprocessors and maturer functions
so the size has grown bigger in real applications. According to the value
reported by customers, we think reserved 2MiB for BL31 might be enough
for maybe the following 2 or 3 years.
Cc: stable@vger.kernel.org # v5.19
Fixes: 6147314aee ("arm64: dts: mediatek: Add device-tree for MT8195 Demo board")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221111095540.28881-1-macpaul.lin@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd49776d8f458bba5499384131eddc0b8bcaf50c upstream.
The pin configuration (done with generic pin controller helpers and
as expressed by bindings) requires children nodes with either:
1. "pins" property and the actual configuration,
2. another set of nodes with above point.
The qup_i2c12_default pin configuration used second method - with a
"pinmux" child.
Fixes: 44acee2078 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220930192039.240486-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3638ea010c37e1e6d93474c4b3368f403600413f upstream.
The pin configuration (done with generic pin controller helpers and
as expressed by bindings) requires children nodes with either:
1. "pins" property and the actual configuration,
2. another set of nodes with above point.
The qup_i2c12_default pin configuration used second method - with a
"pinmux" child.
Fixes: d4b341269e ("arm64: dts: qcom: Add support for Samsung Galaxy Book2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220930192039.240486-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f446022b932aff1d6a308ca5d537ec2b512debdc upstream.
There are three UFS reference clocks on SC8280XP which are used as
follows:
- The GCC_UFS_REF_CLKREF_CLK clock is fed to any UFS device connected
to either controller.
- The GCC_UFS_1_CARD_CLKREF_CLK and GCC_UFS_CARD_CLKREF_CLK clocks
provide reference clocks to the two PHYs.
Note that this depends on first updating the clock driver to reflect
that all three clocks are sourced from CXO. Specifically, the UFS
controller driver expects the device reference clock to have a valid
frequency:
ufshcd-qcom 1d84000.ufs: invalid ref_clk setting = 0
Fixes: 152d1faf1e ("arm64: dts: qcom: add SC8280XP platform")
Fixes: 8d6b458ce6 ("arm64: dts: qcom: sc8280xp: fix ufs_card_phy ref clock")
Fixes: f3aa975e23 ("arm64: dts: qcom: sc8280xp: correct ref clock for ufs_mem_phy")
Link: https://lore.kernel.org/lkml/Y2OEjNAPXg5BfOxH@hovoldconsulting.com/
Cc: stable@vger.kernel.org # 5.20
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221104092045.17410-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9905370560d9c29adc15f4937c5a0c0dac05f0b4 upstream.
The pin configuration (done with generic pin controller helpers and
as expressed by bindings) requires children nodes with either:
1. "pins" property and the actual configuration,
2. another set of nodes with above point.
The qup_spi2_default pin configuration uses alreaady the second method
with a "pinmux" child, so configure drive-strength similarly in
"pinconf". Otherwise the PIN drive strength would not be applied.
Fixes: 8d23a00404 ("arm64: dts: qcom: db845c: add Low speed expansion i2c and spi nodes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221010114417.29859-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0953777640354dc459a22369eea488603d225dd9 upstream.
The SC8280XP UFS controllers are cache coherent and must be marked as
such in the devicetree to avoid potential data corruption.
Fixes: 152d1faf1e ("arm64: dts: qcom: add SC8280XP platform")
Cc: stable@vger.kernel.org # 6.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221205100837.29212-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8d8840c72b3df61b5252052b79020dabec01ab5 upstream.
When adding support for the DisplayPort part of the QMP PHY the binding
(and devicetree parser) for the (USB) child node was simply reused and
this has lead to some confusion.
The third DP register region is really the DP_PHY region, not "PCS" as
the binding claims, and lie at offset 0x2a00 (not 0x2c00).
Similarly, there likely are no "RX", "RX2" or "PCS_MISC" regions as
there are for the USB part of the PHY (and in any case the Linux driver
does not use them).
Note that the sixth "PCS_MISC" region is not even in the binding.
Fixes: 5aa0d1becd ("arm64: dts: qcom: sm8250: switch usb1 qmp phy to USB3+DP mode")
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111094729.11842-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 347b9491c595d5091bfabe65cad2fd6eee786153 upstream.
When adding support for the DisplayPort part of the QMP PHY the binding
(and devicetree parser) for the (USB) child node was simply reused and
this has lead to some confusion.
The third DP register region is really the DP_PHY region, not "PCS" as
the binding claims, and lie at offset 0x2a00 (not 0x2c00).
Similarly, there likely are no "RX", "RX2" or "PCS_MISC" regions as
there are for the USB part of the PHY (and in any case the Linux driver
does not use them).
Note that the sixth "PCS_MISC" region is not even in the binding.
Fixes: 23737b9557 ("arm64: dts: qcom: sm6350: Add USB1 nodes")
Cc: stable@vger.kernel.org # 5.16
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111094729.11842-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7372b944a6ba5ac86628eaacc89ed4f103435cb9 ]
When enabling the APPS SMMU the mainline driver reconfigures the SMMU
from its bootloader configuration, losing the stream mapping for (among
which) the SDHCI hardware and breaking its ADMA feature. This feature
can be disabled with:
sdhci.debug_quirks=0x40
But it is of course desired to have this feature enabled and working
through the SMMU.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sm7225-fairphone-fp4
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221030073232.22726-11-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d561dc4e5cc31e757f91eb7bb709d2e2a8c9ce0 ]
SDHCI on SM8450 HDK also has problems with SDR104/SDR50:
mmc0: card never left busy state
mmc0: error -110 whilst initialising SD card
so I think it is safe to assume this issue affects all SM8450 boards.
Move the quirk disallowing these modes to the SoC DTSI, to spare people
working on other boards the misery of debugging this issue.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221026200357.391635-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8c1d798a2e5091128c391c6dadcc9be334af3f5 ]
We use is_ttbr0_addr() in noinstr code, but as it's only marked as
inline, it's theoretically possible for the compiler to place it
out-of-line and instrument it, which would be problematic.
Mark is_ttbr0_addr() as __always_inline such that that can safely be
used from noinstr code. For consistency, do the same to is_ttbr1_addr().
Note that while is_ttbr1_addr() calls arch_kasan_reset_tag(), this is a
macro (and its callees are either macros or __always_inline), so there
is not a risk of transient instrumentation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221114144042.3001140-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad2631b5645a1d0ca9bf6fecf71f77e3b0071ee5 ]
The actual clock feeding into the Mali GPU on the MT8183 is from the
clock gate in the MFGCFG block, not CLK_TOP_MFGPLL_CK from the TOPCKGEN
block, which itself is simply a pass-through placeholder for the MFGPLL
in the APMIXEDSYS block.
Fix the hardware description with the correct clock reference.
Fixes: a8168cebf1 ("arm64: dts: mt8183: Add node for the Mali GPU")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220927101128.44758-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be8f6b6496076588fd49cbe5bfaaf3ab883eb779 ]
sm3_neon_transform() is called via indirect function calls. Therefore
it needs to use SYM_TYPED_FUNC_START instead of SYM_FUNC_START to cause
its type hash to be emitted when the kernel is built with
CONFIG_CFI_CLANG=y. Otherwise, the code crashes with a CFI failure (if
the compiler didn't happen to optimize out the indirect call).
Fixes: c50d32859e ("arm64: Add types to indirect called assembly functions")
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a41b2129461f6c88e087ca9a6e2fde34cb6deb48 ]
This patch adds the NEON acceleration implementation of the SM3 hash
algorithm. The main algorithm is based on SM3 NEON accelerated work of
the libgcrypt project.
Benchmark on T-Head Yitian-710 2.75 GHz, the data comes from the 326 mode
of tcrypt, and compares the performance data of sm3-generic and sm3-ce.
The abscissas are blocks of different lengths. The data is tabulated and
the unit is Mb/s:
update-size | 16 64 256 1024 2048 4096 8192
---------------+--------------------------------------------------------
sm3-generic | 185.24 221.28 301.26 307.43 300.83 308.82 308.91
sm3-neon | 171.81 220.20 322.94 339.28 334.09 343.61 343.87
sm3-ce | 227.48 333.48 502.62 527.87 520.45 534.91 535.40
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: be8f6b649607 ("crypto: arm64/sm3 - fix possible crash with CFI enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56d32c51dffac8a431b472a4c31efb8563b048d1 ]
The PCIe iommu nodes use "dart" as node names. Replace it with the
the standard "iommu" node name as all other iommu nodes.
Fixes: 3c866bb795 ("arm64: dts: apple: t8103: Add PCIe DARTs")
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 248400656b1cd85de37f3742d065dc1826cdf589 ]
commit edf408b946 ("PCI: dwc: Validate iATU outbound mappings against
hardware constraints") exposes an issue with the existing partitioning of
the aperture space where the Prefetchable apertures of controllers
C5, C7 and C9 in Tegra234 cross the 32GB boundary hardware constraint.
This patch makes sure that the Prefetchable region doesn't spill over
the 32GB boundary.
Fixes: ec142c44b0 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f535cc583759c9c60d4cc9b8d221762e2d75387 ]
Update its unit name to oscillator-26m and remove the unneeded unit
address to fix a unit_address_vs_reg warning.
Fixes: 464c510f60 ("arm64: dts: mediatek: add mt6797 support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d4516f53a611b362db7ba7a8889923d469f57e1 ]
The unit address for the pinctrl node is (0x)1000b000 and not
(0x)10005000, which is the syscfg_pctl_a address instead.
This fixes the following warning:
arch/arm64/boot/dts/mediatek/mt2712e.dtsi:264.40-267.4: Warning
(unique_unit_address): /syscfg_pctl_a@10005000: duplicate
unit-address (also used in node /pinctrl@10005000)
Fixes: f0c64340b7 ("arm64: dts: mt2712: add pintcrl device node.")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d759c524c15dc4151e40b9e3f368147fda7b789 ]
Rename fixed-clock oscillators to oscillator-26m and oscillator-32k
and remove the unit address to fix the unit_address_vs_reg warning;
fix the unit address for interrupt and intpol controllers by
removing a leading zero in their unit address.
This commit fixes the following warnings:
(unit_address_vs_reg): /oscillator@0: node has a unit name, but
no reg or ranges property
(unit_address_vs_reg): /oscillator@1: node has a unit name, but
no reg or ranges property
(simple_bus_reg): /soc/interrupt-controller@0c000000: simple-bus
unit address format error, expected "c000000"
(simple_bus_reg): /soc/intpol-controller@0c53a650: simple-bus
unit address format error, expected "c53a650"
Fixes: 4c7a626077 ("arm64: dts: add dts nodes for MT6779")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7898d047b1eb2bec2622668cd70181442a580c6d ]
Rename the oscillator fixed-clock to oscillator-40m and remove
the unit address to fix warnings.
arch/arm64/boot/dts/mediatek/mt7986a.dtsi:17.23-22.4: Warning
(unit_address_vs_reg): /oscillator@0: node has a unit name,
but no reg or ranges property
Fixes: 1f9986b258 ("arm64: dts: mediatek: add clock support for mt7986a")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 513c43328b189874fdfee3ae99cac81e5502e7f7 ]
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A78) cluster at a maximum of 3000MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculate the mean result for each cluster
4. Calculate DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scale results to 1024:
result_c0 = (dmips_mhz_c0 - min_dmips_mhz(c0, c1)) /
(max_dmips_mhz(c0, c1) - min_dmips_mhz(c0, c1)) * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 11990400 Dhry/s
Cluster 1 (BIG): 59809036 Dhry/s
The calculated scaled results are:
Cluster 0: 307,934312801831 (rounded to 308)
Cluster 1: 1024
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221005093404.33102-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8aa36c22da7d64c5a5d89ccb4a2abb9aeaab2e3 ]
The parent's input irq number is wrongly subtracted with 32 instead of
using the exact numbers in:
https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j721s2/interrupt_cfg.html
The GPIO interrupts are not working because of that. The toggling works
fine but interrupts are not firing. Fix the parent's input irq that
specifies the base for parent irq.
Tested for MAIN_GPIO0_6 interrupt on the j721s2 EVM.
Fixes: b8545f9d3a ("arm64: dts: ti: Add initial support for J721S2 SoC")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220922072950.9157-1-j-keerthy@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
