Convert 3c509 driver to isa_driver and pnp_driver. The result is that
autoloading using udev and hibernation works with ISA PnP cards. It also adds
hibernation support for non-PnP ISA cards.
xcvr module parameter was removed as its value was not used.
Tested using 3 ISA cards in various combinations of PnP and non-PnP modes.
EISA and MCA only compile-tested.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The asix usb driver currently depends on NET_ETHERNET which means you
cannot enable this driver if you only have 1000mbit enabled in your kernel.
Since there is no real dependency between the NET_ETHERNET portion and the
asix driver, simply drop it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the "&& skb->ip_summed == CHECKSUM_PARTIAL" part out of
emac_has_feature parameters.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/pasemi_mac.c is enabled by CONFIG_PASEMI_MAC, which depends on
PPC64 && PCI. However pasemi_mac.c uses several routines that are only
built when PPC_PASEMI is selected. This can lead to an unbuildable config:
ERROR: ".pasemi_dma_start_chan" [drivers/net/pasemi_mac.ko] undefined!
So make CONFIG_PASEMI_MAC depend on PPC_PASEMI instead of PPC64.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Updated version number.
- Resubmitting with correct version update.
- this patch to be applied for upstream-davem branch
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove superfluous in-atomic() check; ethtool MII ops are called from task
context.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The loop forgot to walk the net->mc_list list, so only the first
multicast address was programmed into the hash table.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If "location" is > "addr_len" bits, the high bits of location would interfere
with the READ_CMD sent to the eeprom controller.
A patch was submitted to bug:
http://bugzilla.kernel.org/show_bug.cgi?id=4420
which simply truncated the "location", read whatever was in "location
modulo addr_len", and returned that value. That avoids confusing the
eeprom but seems like the wrong solution to me.
Correct would be to not read beyond "1 << addr_len" address of the eeprom.
I am submitting two changes to implement this:
1) tulip_read_eeprom will return zero (since we can't return -EINVAL)
if this is attempted (defensive programming).
2) In tulip_core.c, fix the tulip_read_eeprom caller so they don't
iterate past addr_len bits and make sure the entire tp->eeprom[]
array is cleared.
I konw we don't strictly need both. I would prefer both in the tree
since it documents the issue and provides a second "defense" from
the bug from creeping back in.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
original_mtu is only used if we end up with a non-NULL
dev, and it is assigned in all such cases, but GCC can't
see that.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tries to make dmesg logs between different runs easier
to compare by
* removing the jiffies (use CONFIG_PRINTK_TIME if you need
timing)
* remove the line numbers, they change with each applied patch
It also changes the deprecated __FUNCTION__ to __func__ to make
checkpatch.pl happy.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch alters the A-MPDU MLME in sta_info to use dynamic allocation,
thus drastically improving memory usage - from a constant ~2 Kbyte in
the previous (static) allocation to a lower limit of ~200 Byte and an upper
limit of ~2 Kbyte.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has nowhere been used. Note: in the firmware manual this was
documented as CMD_802_11_PA_CFG. If we ever need it, we can/should
re-implement it as a direct command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix types of is_open and iw_mode members
of iwl_priv sturct
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch provides a default callback for ASYNC host commands instead
of calling to BUG_ON. Most of the callbacks are now just empty functions
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gives the function's caller name in case NIC
access reference count was not used by it.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl-4965-io.h back to iw-io.h
it also remove 4965 from all functions it supplies
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add LEDS support to 3965 and 4965 drivers. It is based on
led trigger and class. For our drivers we needed to avoid two things.
1- We receive led trigger on/off on each Rx\Tx frame. In our driver
we can not call led command like that. In this driver once driver
receive a start of traffic it call the led command to start blinking
then we count all bytes of Tx and Rx frame, after two second we count the
blink rate of last two second then id blink rate changed we call the led
commands
2- Since we can call led command very often, we make sure we call the
led command after we receive the statistics notification so
we don't need to wake up the ucode id it is in sleep state.
This patch was tested with 4965 and 3945.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Ian Schram<ischram@telenet.be>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware never seem to accept the "goto sleep" command, since the legacy
drivers don't have suspend and resume handlers the entire code for it was
basically a educated guess (based on the "enable radio" code).
This patch will only print a warning when the "goto sleep" command fails, and
just continues as usual. Perhaps that means the device will not reach a sleep
state and consumes more power then it should, but it is equally possible it
simply needs some seconds longer to sleep. Anyway, by making the command
non-fatal it will not block the rest of the suspend procedure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit e6bafba5b4765a5a252f1b8d31cbf6d2459da337, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Guy Cohen <guy.cohen@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a bug detected by CONFIG_DEBUG_SPINLOCK:
if_cs_get_int_status() is only called from lbs_thread(), via
priv->hw_get_int_status. However, lbs_thread() has already taken the
priv->driver_lock. So it's a fault to take the same lock again here.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Fix Rx/Tx HW interrupt coalescing counter reset logic. Disabling
is required before resetting the counter.
- Update the Default both Rx and Tx coalescing timer
threshold. Formerly 4 is set which is equal to 1.5 frame at the line
rate of 1GbE interface, and it doesn't match to the coalescing frame
count which is set to 16. Threashold 21 is matched to frame count 16.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the LAST bit is not set in the RxBD, it's possible we're processing
an incomplete frame, which is bad. While we're at it, add a constant
for the error bitmask, so the whole if-clause fits on one line,
and is more legible.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In gfar_change_mtu(), the frame size needs to be increased to account
for the extra 4 bytes VLAN adds to the ethernet header. However,
it was being increased by the length of the whole header (18 bytes),
which is wrong.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Buffer stashing parameter change to 96 from 64 in order to cover
the Layer 4 header.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code opening proc entry for each device makes the
same thing, as the single_open does, so remove the
unneeded code.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for BCM5481 PHY. Unfortunately it's hard to
get specifications for this PHY, so its special register 0x18 isn't
annotated properly (but we know it's used to set up the delays).
I've kept the magic numbers, so we'll not forget to fix it at the
first opportunity, and will name that register and its bits correctly.
p.s. also fixed the line with broken indention, introduced by
commit 03157ac31eb4a8883382a212b161d2e6c5059fbf
PHYLIB: Add BCM5482 PHY support
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert byte order of constant instead of variable which can be done at
compile time (vs run time)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert P.J. Day proposed to use the macro FIELD_SIZEOF in replace of code
that matches its definition.
The modification was made using the following semantic patch
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
type t;
identifier f;
@@
- (sizeof(((t*)0)->f))
+ FIELD_SIZEOF(t, f)
@depends on haskernel@
type t;
identifier f;
@@
- sizeof(((t*)0)->f)
+ FIELD_SIZEOF(t, f)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the IDT rc32434 Ethernet MAC
we can find in the IDT boards and the Mikrotik RB500.
Driver references some code from the linux-mips RB500
support.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Philip Rischel <rischelp@idt.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This timer doesn't need to run at precise times, so round it to a whole
second to decrease wakeups.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
isa_bus_to_virt() is the wrong thing to do here; it happens
to work on i386, but only by accident. What we want is
normal ioremap/readb/etc. set - it's all in iomem.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
take iscp-based testing into helper, kill the loop, stop
wanking with reassignments of priv->iscp
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* initialize spinlock once
* check586() used to be done before we'd allocated ->priv; these days
it's there from the very beginning, so we don't have to play with
private copy. Consequently, we don't need to mess with reinitializing
->base, etc. afterwards.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
