* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
workqueue: wake up a worker when a rescuer is leaving a gcwq
Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org # ca86828: x86, AMD, PCI: Add AMD northbridge PCI device
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add missing frac fb div flag for dce4+
drm/radeon/kms: do not reject X16 and Y16X16 floating-point formats on r300
drm/nouveau: fix suspend/resume on GPUs that don't have PM support
drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
drm/nv40: fix tiling-related setup for a number of chipsets
drm/nouveau: fix non-EDIDful native mode selection
drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.
This patch re-enables UIE timer/polling emulation for rtc devices
that do not support alarm irqs.
CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Uwe pointed out that my alarm based UIE emulation is not sufficient
to replace the older timer/polling based UIE emulation on devices
where there is no alarm irq. This causes rtc devices without alarms
to return -EINVAL to UIE ioctls. The fix is to re-instate the old
timer/polling method for devices without alarm irqs.
This patch reverts the following commits:
042620a018 - Remove UIE emulation
1daeddd596 - Cleanup removed UIE emulation declaration
b5cc8ca1c9 - Remove Kconfig symbol for UIE emulation
The emulation mode will still need to be wired-in with a following
patch before it will work.
CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
On hardware that doesn't support alarm interrupts, rtc_alarm_irq_enable
could return without releasing the ops_lock mutex.
This was introduced in
aa0be0f (RTC: Propagate error handling via rtc_timer_enqueue properly)
This patch corrects the issue by only returning once the mutex is
released.
[john.stultz: Reworded the commit log]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This is useful for system management software so that it can kick
off things like gettys and everything that's started from a tty,
before we reuse it from/for something else or shut it down.
Without this ioctl it would have to temporarily become the owner of
the tty, then call vhangup() and then give it up again.
Cc: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If management firmware is present and the device is down, the firmware
will assume control of the phy. If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior. This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without calling of netif_carrier_off at the end of the probe the operstate
is unknown when the device is initially opened. By default the carrier is
on so when the device is opened and netif_carrier_on is called the link
watch event is not fired and operstate remains zero (unknown).
This patch fixes this behavior in forcedeth and r8169.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a double completion associated with error handling for RC QPs.
The sequence is:
- The do_rc_ack() routine fields an RNR nack and there are 0
rnr_retries configured on the QP.
- qib_error_qp() stops the pending timer
- qib_rc_send_complete() is called from sdma_complete()
- qib_rc_send_complete() starts the timer because the msb of the psn
just completed says an ack is needed.
- a bunch of flushes occur as ipoib posts WQEs to an error'ed QP
- rc_timeout() calls qib_restart_rc()
- qib_restart_rc() calls qib_send_complete() with a
IB_WC_RETRY_EXC_ERR on a wqe that has already been completed in the
past
The fix avoids starting the timer since another packet will never
arrive.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Was this exploitable - who knows, but it was certainly totally broken
Signed-of-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This basically encapsulates the small bit of locking knowledge needed. While
we are at it make sure we blow up on any more abusers and unsafe misuses of
ioctl for this kind of stuff.
We change the function to return an argument as at some point it needs to
honour the POSIX 'I asked for changes but got none of them' error reporting
corner case.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only oddities here are a couple of drivers that bogusly called the ldisc
helpers instead of returning -ENOIOCTLCMD. Fix the bug and the rest goes
away.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't use it so we can trim it from here as we try and stamp the file
object dependencies out of the serial code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the regshift member of struct uart_port to store the address stride
from platform data. This way we can save one dereference per call of
altera_uart_readl and altera_uart_writel.
This also allows us to use the driver without platform data, which is
needed for device tree support in the Nios2 port.
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 6b5756f176 introduced the
possibility for pdev->id being -1 but the change was not done equally in
altera_uart_remove. This patch fixes this.
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
using VT_SETACTIVATE ioctl for console switch did not work,
since it put wrong param to the set_console function.
Also ioctl returned misleading error, because of the missing
break statement. I wonder anyone has ever used this one :).
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enables PPS support in atmel serial driver to make PPS API working.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In 8250.c original ns16550 autoconfig code, we change the divisor latch when
we goto to high speed mode, we're assuming the previous speed is legacy. This
some times is not true.
For example in a system with both CONFIG_SERIAL_8250 and
CONFIG_SERIAL_8250_PNP set, in this case, the code (autoconfig) will be called
twice, one in serial8250_init/probe() and the other is from
serial_pnp_probe. When serial_pnp_probe calls the autoconfig for NS16550A,
it's already in high speed mode, change the divisor latch (quot << 3) in this
case will make the UART console garbled.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
CC: stable@kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For any reason if the NS16550A was not work in high speed mode (e.g. we hold
NS16550A from going to high speed mode in autoconfig_16550a()), now we are
resume from suspend, we should also set the uartclk to the correct
value. Otherwise it is still the old 1843200 and that will bring issues.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
CC: stable@kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renamed spi_driver variable to not be h/w specific
set driver name to use DRVNAME define
removed commented-out define
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe routine should call spi_setup() to configure
the SPI bus so it can properly communicate with the device.
E.g. the device operates in SPI mode 1.
Called spi_setup to configure SPI mode, max_speed_hz, and bpw
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platforms containing the 6260 can run up to 25Mhz.
For these platforms set max_speed_hz to 25Mhz.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
driver should support 32bit SPI transfers. The boolean variable
only allowed 8/16.
Changed to support 8/16/32 for future enabling
of 32 bpw.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a SPI protocol driver and has no DMA ops
associated with the device so the call will fail. Furthermore,
the DMA allocation made here will be used by the SPI
controller driver (parent dev) so it makes sense to
pass that device instead.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port ops must be set AFTER calling port init as that function
zeroes the structure
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
seems there's no longer need for using con_buf/conf_buf_mtx
as vcs_read/vcs_write buffer for user's data.
The do_con_write function, that was the other user of this,
is currently using its own kmalloc-ed buffer.
Not sure when this got changed, as I was able to find this code
in 2.6.9, but it's already gone as far as current git history
goes - 2.6.12-rc2.
AFAICS there's a behaviour change with the current change.
The lseek is not completely mutually exclusive with the
vcs_read/vcs_write - the file->f_pos might get updated
via lseek callback during the vcs_read/vcs_write processing.
I tried to find out if the prefered behaviour is to keep
this in sync within read/write/lseek functions, but I did
not find any pattern on different places.
I guess if user end up calling write/lseek from different
threads she should know what she's doing. If needed we
could use dedicated fd mutex/buffer.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
printk()s without a priority level default to KERN_WARNING. To reduce
noise at KERN_WARNING, this patch set the priority level appriopriately
for unleveled printks()s. This should be useful to folks that look at
dmesg warnings closely.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the existing bfin_jtag_comm TTY driver to the HVC layer so
that the common HVC code can worry about all of the TTY/polling crap and
leave the Blackfin code to worry about the Blackfin bits.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
virtual console: add keyboard mode OFF
Add a new mode for the virtual console keyboard OFF in which all input
other than shift keys is ignored. Prevents vt input buffers from
overflowing when a program opens but doesn't read from a tty, like X11
using evdev for input.
Signed-off-by: Arthur Taylor <art@ified.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 3880 storage control unit supports a 3380 device
type, but not a 3390 device type.
Reported-by: Stephen Powell <zlinuxman@wowway.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Otherwise we fail to properly suspend/resume all of the emulated devices.
Something between 2.6.38-rc2 and rc3 appears to have exposed this
issue, but it's always been wrong not to do this.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
A HW limitation was recently discovered where the last buffer in a DDP offload
cannot be a full buffer size in length. Fix the issue with a work around by
adding another buffer with size = 1.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Systems containing an 82599EB and running a backported driver from
upstream were panicing on boot. It turns out hw->mac.ops.setup_sfp is
only set for 82599, so one should check to be sure that pointer is set
before continuing in ixgbe_sfp_config_module_task. I verified by
inspection that the upstream driver has the same issue and also added a
check before the call in ixgbe_sfp_link_config.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not flushing all writebacks before unloading, possibly
causing memory to be written by the hardware after the driver had
reinitialized the rings.
This adds missing functionality to flush any pending writebacks and is
called in all spots where descriptors should be completed before the driver
begins processing.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is part of a fix to avoid any tasks running while the driver is
exiting and deinitializing resources.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* 'nouveau/drm-nouveau-next' of /ssd/git/drm-nouveau-next:
drm/nouveau: fix suspend/resume on GPUs that don't have PM support
drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
drm/nv40: fix tiling-related setup for a number of chipsets
drm/nouveau: fix non-EDIDful native mode selection
drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.
The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+. Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We free the temporary binding before leaving this function, so we also have
to wait for the move to actually complete.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Due to the default case handling the older chipsets, a bunch of the newer
ones ended up having the wrong tiling regs used. This commit switches the
default case to handle the newest chipsets.
This also makes nv4e touch the "extra" tiling regs. "nv" doesn't touch
them for C51 but traces of the NVIDIA binary driver show it being done
there.
I couldn't find NV41/NV45 traces to confirm the behaviour there, but an
educated guess was taken at each of them.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The DRM core fills this value, but at too late a stage for this to work,
possibly resulting in an undesirable mode being selected.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Alex Buell <alex.buell@munted.org.uk>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Alex Buell <alex.buell@munted.org.uk>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'. The former is the more prominent one. The latter is
mostly used by workqueue and in a few other odd places. Unify the
spelling to 'freezable'.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>
On systems where the temperature sensor is actually used, the BIOS is
likely to have locked the alarm registers. In that case, all writes
through the corresponding sysfs files would be silently ignored.
To prevent this, detect the locks and make the affected sysfs files
read-only.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The documentation lists standard numbers and chip names in excruciating
detail, but that's all it does. To help mere mortals in deciding
whether to enable this driver, mention what this sensor is for and in
which systems it might be found.
Also add a link to the actual JC 42.4 specification.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In set_temp_crit_hyst(), make the variable 'val' have the correct
type for strict_strtoul().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
drm/radeon/kms: hopefully fix pll issues for real (v3)
drm/radeon/kms: add bounds checking to avivo pll algo
drm: fix wrong usages of drm_device in DRM Developer's Guide
drm/radeon/kms: fix a few more atombios endian issues
drm/radeon/kms: improve 6xx/7xx CS error output
drm/radeon/kms: check AA resolve registers on r300
drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
drm/radeon/kms: use linear aligned for evergreen/ni bo blits
drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
drm/radeon: fix race between GPU reset and TTM delayed delete thread.
drm/radeon/kms: evergreen/ni big endian fixes (v2)
drm/radeon/kms: 6xx/7xx big endian fixes
drm/radeon/kms: atombios big endian fixes
drm/radeon: 6xx/7xx non-kms endian fixes
drm/radeon/kms: optimize CS state checking for r100->r500
drm: do not leak kernel addresses via /proc/dri/*/vma
drm/radeon/kms: add connector table for mac g5 9600
radeon mkregtable: Add missing fclose() calls
drm/radeon/kms: fix interlaced modes on dce4+
drm/radeon: fix memory debugging since d961db75ce
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
pci: use security_capable() when checking capablities during config space read
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / Video: Probe for output switch method when searching video devices.
ACPI / Wakeup: Enable button GPEs unconditionally during initialization
ACPI / ACPICA: Avoid crashing if _PRW is defined for the root object
ACPI: Fix acpi_os_read_memory() and acpi_os_write_memory() (v2)
Right now the platform device and its platform data is included in one big
struct which requires its custom ->release function. The problem with the
release function within the driver is that it might be called after the
driver was removed because someone was holding a reference to it and it
was not called right after platform_device_unregister(). So we also free
the platform device memory to which one might hold a reference.
This patch uses the normal pdev functions so this kind of race does not
occur.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There was a bug in my commit c978e7bb77
("hisax: Fix unchecked alloc_skb() return.")
One of the l2->flag checks is wrong.
Even worse it turns out I'm duplicating an existing function,
so use that instead.
Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (21 commits)
dmaengine: add slave-dma maintainer
dma: ipu_idmac: do not lose valid received data in the irq handler
dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()
dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()
dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()
dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of sdma_prep_slave_sg()
dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()
dmaengine i.MX dma: initialize dma capabilities outside channel loop
dmaengine i.MX DMA: do not initialize chan_id field
dmaengine i.MX dma: check sg entries for valid addresses and lengths
dmaengine i.MX dma: set maximum segment size for our device
dmaengine i.MX SDMA: reserve channel 0 by not registering it
dmaengine i.MX SDMA: initialize dma capabilities outside channel loop
dmaengine i.MX SDMA: do not initialize chan_id field
dmaengine i.MX sdma: check sg entries for valid addresses and lengths
dmaengine i.MX sdma: set maximum segment size for our device
DMA: PL08x: fix channel pausing to timeout rather than lockup
DMA: PL08x: fix infinite wait when terminating transfers
dmaengine: imx-sdma: fix inconsistent naming in sdma_assign_cookie()
dmaengine: imx-sdma: propagate error in sdma_probe() instead of returning 0
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, dmi, debug: Log board name (when present) in dmesg/oops output
x86, ioapic: Don't warn about non-existing IOAPICs if we have none
x86: Fix mwait_usable section mismatch
x86: Readd missing irq_to_desc() in fixup_irq()
x86: Fix section mismatch in LAPIC initialization
If the target device gets lost, this fix is needed, as it causes
negative unintended responses on basic I/O tests. If the target device
gets lost, the upstream qla2xxx driver returns
SCSI_MLQUEUE_TARGET_BUSY which causes an immediate retry without drop
in the number of allowed retries. This semantic change, as a result of
removing FC_DEVICE_LOST check is reasonable, as it only extends a
short transitional period, until the transport is called to notify
that the rport as lost (fc_remote_port_delete()). Once transport
notification is done, fc_remote_port_chkready() check will take over.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea. The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space. The normal capable() interface returns
true on success, but the LSM interface returns 0 on success. This thinko
is now fixed in this patch, and has been confirmed to work properly.
So, once again...Eric Paris noted that commit de139a3 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: Eric Paris <eparis@redhat.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.
( Please note that Type 2 is not listed in Table 3 in Sec 6.2
("Required Structures and Data") of the SMBIOS v2.7
Specification. )
Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.
Before the fix:
(i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6
After the fix:
(i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
VF Driver should use mailbox command timeout specified in t4fw_interface.h
rather than hard-coded value of 500ms.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a Virtual Machine is rebooted, KVM currently fails to issue a Function
Level Reset against any "Attached PCI Devices" (AKA "PCI Passthrough"). In
addition to leaving the attached device in a random state in the next booted
kernel (which sort of violates the entire idea of a reboot reseting hardware
state), this leaves our peer thinking that the link is still up. (Note that
a bug has been filed with the KVM folks, #25332, but there's been no
response on that as of yet.) So, we add a "->shutdown()" method for the
Virtual Function PCI Device to handle administrative shutdowns like a
reboot.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_DEBUG_FS we get "ERR_PTR()"s back from the debugfs routines
instead of NULL. Use the right predicates to check for this.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check module parameter validity in the module initialization routine instead
of the PCI Device Probe routine.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.
v2: testing options
v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852https://bugzilla.kernel.org/show_bug.cgi?id=24462https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the specification of hardware,
the processing at the time of driver starting was modified.
This device write automatically the MAC address read from serial ROM
into a MAC Adress1A/1B register at the time of power on reset.
However, when stable clock is not supplied,
the writing of MAC Adress1A/1B register may not be completed.
In this case, it is necessary to load MAC address to MAC Address1A/1B register
by the MAC Address1 load register.
This patch always does the above processing,
in order not to be dependent on system environment.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes this build warning:
drivers/net/wireless/iwlwifi/iwl-3945.c:411:13: warning: 'iwl3945_good_plcp_health' defined but not used
As per Johannes Berg.
Signed-off-by: David S. Miller <davem@davemloft.net>
The statement 'select CAN_SOFTING' may ignore the dependancies
for CAN_SOFTING while selecting CAN_SOFTING_CS, as is therefore a bad choice.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: Fix minor compile warning
RTC: Convert rtc drivers to use the alarm_irq_enable method
RTC: Fix rtc driver ioctl specific shortcutting
Currently when two or more buffers are queued by the camera driver
and so the double buffering is enabled in the idmac, we lose one
frame comming from CSI since the reporting of arrival of the first
frame is deferred by the DMAIC_7_EOF interrupt handler and reporting
of the arrival of the last frame is not done at all. So when requesting
N frames from the image sensor we actually receive N - 1 frames in
user space.
The reason for this behaviour is that the DMAIC_7_EOF interrupt
handler misleadingly assumes that the CUR_BUF flag is pointing to the
buffer used by the IDMAC. Actually it is not the case since the
CUR_BUF flag will be flipped by the FSU when the FSU is sending the
<TASK>_NEW_FRM_RDY signal when new frame data is delivered by the CSI.
When sending this singal, FSU updates the DMA_CUR_BUF and the
DMA_BUFx_RDY flags: the DMA_CUR_BUF is flipped, the DMA_BUFx_RDY
is cleared, indicating that the frame data is beeing written by
the IDMAC to the pointed buffer. DMA_BUFx_RDY is supposed to be
set to the ready state again by the MCU, when it has handled the
received data. DMAIC_7_CUR_BUF flag won't be flipped here by the
IPU, so waiting for this event in the EOF interrupt handler is wrong.
Actually there is no spurious interrupt as described in the comments,
this is the valid DMAIC_7_EOF interrupt indicating reception of the
frame from CSI.
The patch removes code that waits for flipping of the DMAIC_7_CUR_BUF
flag in the DMAIC_7_EOF interrupt handler. As the comment in the
current code denotes, this waiting doesn't help anyway. As a result
of this removal the reporting of the first arrived frame is not
deferred to the time of arrival of the next frame and the drivers
software flag 'ichan->active_buffer' is in sync with DMAIC_7_CUR_BUF
flag, so the reception of all requested frames works.
This has been verified on the hardware which is triggering the
image sensor by the programmable state machine, allowing to
obtain exact number of frames. On this hardware we do not tolerate
losing frames.
This patch also removes resetting the DMA_BUFx_RDY flags of
all channels in ipu_disable_channel() since transfers on other
DMA channels might be triggered by other running tasks and the
buffers should always be ready for data sending or reception.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This PCH_GBE driver had an issue that the receiving data is not normal.
This driver had not removed correctly the padding data
which the DMA include in receiving data.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables it by default when the driver starts.
This has been required by many people and seems to actually be
useful on STB.
At any rate, the WoL modes can be selected and turned-on/off
by using the ethtool at run-time by users.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If alloc_skb() fails to allocate memory and returns NULL then we want to
return -ENOMEM from drivers/atm/solos-pci.c::popen() regardless of the
value of net_ratelimit(). The way the code is today, we may not return if
net_ratelimit() returns 0, then we'll proceed to pass a NULL pointer to
skb_put() which will blow up in our face.
This patch ensures that we always return -ENOMEM on alloc_skb() failure
and only let the dev_warn() be controlled by the value of net_ratelimit().
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In drivers/net/usb/hso.c::hso_create_bulk_serial_device() we have this
code:
...
serial = kzalloc(sizeof(*serial), GFP_KERNEL);
if (!serial)
goto exit;
...
exit:
hso_free_tiomget(serial);
...
hso_free_tiomget() directly dereferences its argument, which in the
example above is a NULL pointer, ouch.
I could just add a 'if (serial)' test at the 'exit' label, but since most
freeing functions in the kernel accept NULL pointers (and it seems like
this was also assumed here) I opted to instead change 'hso_free_tiomget()'
so that it is safe to call it with a NULL argument. I also modified the
function to get rid of a pointles conditional before the call to
'usb_free_urb()' since that function already tests for NULL itself -
besides fixing the NULL deref this change also buys us a few bytes in
size.
Before:
$ size drivers/net/usb/hso.o
text data bss dec hex filename
32200 592 9960 42752 a700 drivers/net/usb/hso.o
After:
$ size drivers/net/usb/hso.o
text data bss dec hex filename
32196 592 9960 42748 a6fc drivers/net/usb/hso.o
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Juhl noticed that l2_pull_iqueue() does not
check to see if alloc_skb() fails.
Fix this by first trying to reallocate the headroom
if necessary, rather than later after we've made hard
to undo state changes.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915: Fix resume regression from 5d1d0cc
drm/i915/tv: Use polling rather than interrupt-based hotplug
drm/i915: Trigger modesetting if force-audio changes
drm/i915/sdvo: If we have an EDID confirm it matches the mode of the connection
drm/i915: Disable RC6 on Ironlake
drm/i915/lvds: Restore dithering on native modes for gen2/3
drm/i915: Invalidate TLB caches on SNB BLT/BSD rings
Makes debugging CS rejections much easier.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is an important security fix because we allowed arbitrary values
to be passed to AARESOLVE_OFFSET. This also puts the right buffer address
in the register.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode. The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode. The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My evergreen has been in a remote PC for week and reset has never once
saved me from certain doom, I finally relocated to the box with a
serial cable and noticed an oops when the GPU resets, and the TTM
delayed delete thread tries to remove something from the GTT.
This stops the delayed delete thread from executing across the GPU
reset handler, and woot I can GPU reset now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on 6xx/7xx endian fixes from Cédric Cano.
v2: fix typo in shader
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
agd5f: minor cleanups
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
