Add sanity checks for fields that could cause division by zero.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Flexible OP PLL pixel clock divider allows a higher OP pixel clock than
what the bus can transfer. This generally makes it easier to select pixel
clock dividers.
This changes how the pixel rate on the bus and minimum VT divisor are
calculated, as the pixel rate is no longer directly determined by the
OP pixel clock and the number of the lanes.
Also add a sanity check for sensors that do not support flexible OP PLL
pixel clock divider. This could have caused the PLL calculator to come up
with an invalid configuration for those devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The l parameter defines the number of clock cycles to process a single
pixel per OP lane. It is calculated based on a new register
op_bits_per_lane.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS allows odd PLL dividers other than 1, granted that the corresponding
capability bit is set. Support this both in the PLL calculator and the CCS
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for decoupled OP domain clock calculation. This means that the
number of VT and OP domain clocks are no longer dependent on the number of
CSI-2 lanes in the lane speed mode.
The support also replaces the existing quirk flag to calculate OP domain
clocks per lane.
Also support decoupled OP domain calculation in the CCS driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Convey the relevant PLL flags to the PLL calculator. Also the lane speed
model affects how the link rate is calculated on the CSI-2 bus, as the
rate is total of all lanes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS PLL includes a capability to calculate the VT clocks on per-lane
basis. Add support for this feature.
Move calculation of the pixel rate on the CSI-2 bus early in the function
as everything needed to calculate it is already available.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use uint32_t instead of unsigned int for a variable that contains
explicitly 32-bit numbers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The additional multiplier (for higher VT timing) of the PLL multiplier was
checked against the upper limit but the result was rounded up, possibly
producing too high additional multiplier. Round down instead to keep
within hardware limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The comment is about minimum PLL multiplier but the related check really
deals with the maximum PLL multiplier.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The external clock frequency times the PLL multiplier may exceed the value
range of 32-bit unsigned integers. Instead perform the same calculation y
using two divisions.
The result has some potential to be different, but that's ok: this number
is used to limit the range of pre-PLL divisors to find optimal values. So
the effect of the rare case of a different result here would mean an
invalid pre-PLL divisor is tried. That will be found out a little later in
any case.
Also guard against dividing by zero if the external clock frequency is
higher than the maximum OP PLL output clock --- a rather improbable case.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The lower bound of the pre-PLL divider was calculated based on OP SYS
clock frequency which is also affected by the OP SYS clock divider. This
is wrong. The right clock frequency is that of the PLL output clock.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OP system clock frequency defines the CSI-2 bus clock frequency, not
the PLL output clock frequency. Both values were overwritten in the end,
but the wrong limit value was used for the OP system clock frequency,
possibly leading to too high frequencies being used.
Also remove now duplicated calculation of OP system clock frequency later
in the PLL calculator.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the BIT macro for setting individual bits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS pll is used by the CCS driver at the moment, but documenting the
interface makes sense. It's non-trivial and the calculator could be used
elsewhere.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This way the struct will use less memory, with better packing and no waste
due to unsigned long.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Differentiate between CSI-2 D-PHY and C-PHY. This does not yet include
support for C-PHY.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The parallel bus PLL calculation has no users. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VT divisor search can be ended if we've already found the value that
corresponds exactly the total divisor, as there are no better (lower)
values available.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the correct video timing divisor to calculate the SYS divisor. Instead
of the current value, the minimum was used. This could have resulted in a
too low SYS divisor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS spec supports a lot of variation in the PLL. Split the PLL in
front and back parts to better prepare for supporting it.
Also use CCS compliant naming for IP and OP PLL frequencies (i.e. include
"clk" in the name).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pll->pll_op_clk_freq is a 32-bit number. It does not need div_u64 to
divide it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
rval wasn't set, resulting in probe returning zero instead of an error.
Fixes: de10c1619c ("[media] smiapp: Get clock rate if it's not available through DT")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is no intialization for the 'reg' variable, so printing
it produces undefined behavior as well as a compile-time warning:
drivers/media/i2c/ccs/ccs-core.c:314:49: error: variable 'reg' is uninitialized when used here [-Werror,-Wuninitialized]
"0x%8.8x %s pixels: %d %s (pixelcode %u)\n", reg,
Remove the variable and stop printing it.
Fixes: fd9065812c ("media: smiapp: Obtain frame descriptor from CCS limits")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clang points out that the error handling in ov02a10_s_stream() is
broken, and just returns a random error code:
drivers/media/i2c/ov02a10.c:537:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (ov02a10->streaming == on)
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/ov02a10.c:568:9: note: uninitialized use occurs here
return ret;
^~~
drivers/media/i2c/ov02a10.c:537:2: note: remove the 'if' if its condition is always false
if (ov02a10->streaming == on)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If streaming is already on, leave it that way and return success.
Suggested-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Fixes: 91807efbe8 ("media: i2c: add OV02A10 image sensor driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use regulators vio and vcore besides vana. The regulators were always
there but on many boards they've been hard wired. Control them explicitly
now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
SMIA nor CCS need these delays; remove them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Longer idle period is required on I²C bus before the first transaction
after lifting xshutdown.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Over the years (and renaming) some lines that may well be wrapped ended up
being over 80 characters, likewise there are shorter lines that can be
merged. Do that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If pm_runtime_get_sync() fails, there's no need to set the device active
again. Also, in the same case to return the usage_count to zero,
pm_runtime_put_noidle() is enough.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Write manufacturer specific registers (MSRs) from file to the sensor on
sensor power-on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make the delay between I²C access retries a range between 1 and 2 ms. Also
make the number of retries 10 instead of 5, in order not to reduce the
total amount of time.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use my @linux.intel.com e-mail address in the CCS driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change MODULE_LICENSE to "GPL v2" as indicated by the SPDX tag.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MIPI CCS replaces SMIA and SMIA++ as the current standard. CCS brings new
features while existing functionality will be supported. Rename the
smiapp-pll as ccs-pll accordingly.
Also add Intel copyright to the files.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some limit values are available in q16.q16 format, referred to as 32-bit
unsigned ireal in CCS. Read these correctly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of converting the limit values at register read time, do that at
access time instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The limit values will be raw soon, and the conversion takes place later
on. Prepare for that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework quirk and 8-bit only access functions with a single function that
takes arguments. This is later extensible to support yet more flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If an internal driver error was encountered, BUG was issued. Instead, do
less harsh WARN_ON_ONCE and try to manage with the consequences.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The NULL check is not needed as the functions do not return NULL. Remove
the check (and BUG).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The register arrays have a certain size but not all the entries will be
relevant. In practice reading can be stopped after encountering a zero
value in the array. Do that to avoid extra reads.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read the CCS static data for sensors and modules. The files are expected
to be found in "ccs" directory.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The module revision number major and minor are both 8 bits while the
sensor revision number is 16 bits. Combine the module revision into one
number.
This also adds printing the lowest 8 bits of the module version through
the sysfs attribute.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a parser library for parsing the CCS static data format.
The library may be also compiled in user space as the format has uses also
in the user space. Therefore it is dual licensed under the 3-clause BSD
license as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Let v4l2_fwnode_endpoint_alloc_parse to figure out the type of the data
bus. As the old bindings did not require the "bus-type" property, we need
to rely on guessing between CSI-2 D-PHY and CCP2. Setting the type to
CSI-2 D-PHY will parse just that and succeed even if no data-lanes are
set.
Also add a comment on the matter to the driver to avoid breaking this in
the future.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to allocate the hardware configuration struct separately.
Put it in struct ccs_sensor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
No need to support platform data; remove support for conveying hardware
configuration that way.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The I²C ID table is no longer needed; remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS compliant sensors use device ID "MIPI0200". Use this id for ACPI
device matching.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add device data specific to DT compatible ID to tell SMIA and CCS devices
apart already in power-up.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add "mipi-ccs-1.0" and "mipi-ccs-1.1" compatible strings to the CCS
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the device is powered off (for example during system suspend to ram)
the devices loses its configuration, especially the slave i2c mappings
and other configuration set at probe time. This renders the device
unusable and the only way to recover is to unbind and rebind the device
to the driver to run the probe setup again.
Add an early resume callback that reinitializes the device and setup the
slave i2c address mappings and other probe time configuration.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's not enough to set the CSI-2 virtual channel for TXA and TXB during
probe: it also needs to be set when the device is reset. Move the virtual
channel selection to adv748x_reset() that is called during probe and
when the device needs to be reset.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's not enough to select the AFE input port during probe: it also needs
to be set when the device is reset. Move the port selection to
adv748x_reset() that is called during probe and when the device needs to
be reset.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
During probe the i2c slave addresses are set two times in a row, once in
adv748x_initialise_clients() and once directly after in adv748x_reset().
Remove the call to adv748x_set_slave_addresses() in
adv748x_initialise_clients() as it's only called during probe while
adv748x_reset() is called during probe and normal operation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If of_graph_get_endpoint_by_regs() return NULL, it will return 0 rather
than an errno, because we doesn't initialize the return value.
Fixes: 0556f1d580 ("media: tvp5150: add input source selection of_graph support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx219 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 8) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
[reword commit message, use macros for pixel offsets]
Fixes: e6d4ef7d58 ("media: i2c: imx219: Implement get_selection")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9271 GPIO1 line that controls the sensor reset is by default
enabled after a serializer chip reset.
As rdacm20 does not go through an explicit serializer reset, make sure
GPIO1 is enabled to make the camera module driver more robust.
Fixes: 34009bffc1 ("media: i2c: Add RDACM20 driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix GPIO enable/disable operations which wrongly read the 0x0f register
to obtain the current mask of the enabled lines instead of using
the correct 0x0e register.
Also fix access to bit 0 of the register which is marked as reserved.
Fixes: 34009bffc1 ("media: i2c: Add RDACM20 driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently pointer nvm is being dereferenced before it is being null
checked. Fix this by moving the assignments of pointers client and
ov2740 so that are after the null check hence avoiding any potential
null pointer dereferences on pointer nvm.
Fixes: 5e6fd339b6 ("media: ov2740: allow OTP data access during streaming")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The lock in ov9734 is used to protect the streaming state and
serialize the stream on and off callbacks, it should be hold before
checking the streaming state in ov9734_set_stream().
Reported-by: Tomasz Figa <tfiga@chromium.org>
Reported-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The DT bindings documented "reset-gpios" property but the driver never
made use of it. Instead it used a GPIO called "xshutdown", with apprently
wrong polarity.
Fix this by requesting "reset" GPIO with the right polarity first, and if
that fails, then request "xshutdown" GPIO with the old polarity. This way
it works for new users as expected while if someone, somewhere, depended
on "xshutdown" GPIO, that continues to work as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This removes a warning at driver probe time telling that one or two
entities have no function set. The function used for both the binner and
scaler is the scaler.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver doesn't do anything tangible with profiles. Remove the notion,
and use the capabilities directly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the "smiapp" driver as "ccs". MIPI CCS is the contemporary standard
for raw Bayer camera sensors. The driver retains support for the SMIA++
and SMIA compliant camera sensors. A module alias is added for old user
space using "smiapp" module name.
Add Intel copyright while at it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Call CCS compliant sensors as "ccs" instead of "smiapp" in absence of a
device specific name. This is done based on the value of the manufacturer
ID register that is only present in CCS.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename internal names to reflect the driver's new reference. The module
name remains the same.
Also fix trivial coding style issues on the way related to e.g. alignment
changes due to the rename.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename register access functions by changing smiapp to ccs.
The functions operating on register addresses have "addr" appended to the
name.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is no longer needed as the smiapp_write() function can be
used to write 8-bit registers with plain register addresses.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Switch to CCS standard registers where they exist. The still relevant SMIA
registers are left as-is and the redundant ones are removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use CCS limits for obtaining binning capabilities and subtypes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS limits have the information so use it instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Obtain the frame descriptor from the CCS limits, instead of reading them
directly from the frame descriptor registers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the CCS limit definitions instead of the SMIA ones. This allows
accessing CCS capabilities where needed as well as dropping the old SMIA
limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read limit and capability values into a driver allocated buffer. This will
later replace (most of) the existing SMIA limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read MIPI CCS manufacturer and version information, and use the CCS IDs
over SMIA whenever they are set.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add two helper macros for reading and writing the CCS registers as defined
in ccs-regs.h.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove macros for defining new SMIA registers, instead put the register
flags to the register definition itself. Also move the register flags to
the same file.
This is not expected to be updated but rather left there as a reference.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Calculate the limit offsets and the size of the limit buffer. CCS limits
are read into this buffer, and the offsets are helpful in accessing the
information in it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the CCS register flags instead of the old smia flags. The
new flags include the register width information that was separate from
the register flags previously.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Import CCS register and limit definitions. These files are generated by a
Perl script based on a text-based register definition file. The generator
was added on
commit 1ec0b899c2 ("media: ccs: Add the generator for CCS register definitions and limits")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These writes to 0x162, 0x163 already appear earlier in the struct for
the 1920x1080 mode and do not need to be repeated.
Signed-off-by: Sameer Puri <purisame@spuri.io>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is supposed to return negative error codes but the type is bool so
it returns true instead.
Fixes: b47b79d8a2 ("[media] media: i2c: max2175: Add MAX2175 support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stop video streaming when requested.
When s_stream is called to stop the video streaming, if/else condition calls
start_streaming function instead of the one for stopping it.
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Signed-off-by: Daniel Gomez <daniel@qtec.com>
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The flag V4L2_SUBDEV_FL_HAS_EVENTS is required if the subdev can
generate events. It can create events from the ctrl handler, therefore
this is required.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because clk_disable_unprepare() already checked NULL clock parameter,
so the additional check is unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OTP data access of ov2740 need enable the streaming mode to load
and it could be done in any time, so driver need allow the OTP
data access during streaming instead of return EBUSY, this patch
try to read the OTP data out in STREAMON if OTP data is not ready
before first time streaming start.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OTP data access of ov2740 in probe need power up, it may cause
the camera flash LED blink during probe if the LED use same power
rail with camera, this patch move the OTP data access out of
probe, it will only occur on demand from user by nvmem sysfs.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the OminiVision ov9734 image sensor
which can deliver maximum 720p image frames at 30 fps. This driver
also add vertical blanking, exposure, test pattern, digital and analog
gain control for the image sensor.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove Jason Chen's e-mail address for it no longer works.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adding muliple status together loses individual failures.
Check each status separately.
Clean up some other returns for consistency.
Fixed several coding style problems by running
the file through checkpatch.pl --fix-inplace
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for test pattern control supported by the sensor.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support to read the bus-type for V4L2_MBUS_BT656 and enable BT.656
mode in the sensor if needed.
For backward compatibility with older DTS where the bus-type property was
not mandatory, assume V4L2_MBUS_PARALLEL as it was the only supported bus
at the time. v4l2_fwnode_endpoint_alloc_parse() will not fail if
'bus-type' is not specified.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Parse endpoint properties using v4l2_fwnode_endpoint_alloc_parse()
to determine the bus type and store it in the driver structure.
Set bus_type to V4L2_MBUS_PARALLEL as it's the only supported one
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_fwnode_parse_endpoint() function can make use of defaults in
multiple bus types. To use this feature, all callers must zero the rest of
the fields of this struct, too. All other drivers appear to do that
already apart from this one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the mode 6 for the sensor, this mode uses
3/8 subsampling and 3 horizontal binning.
Aspect ratio is changed.
Split the bin_ratio variable into two parts, one for
width and one for height, as the ratio is no longer preserved
when doing subsampling in this mode.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX274 has analog 2.8V supply, digital core 1.8V supply, and vddl digital
io 1.2V supply which are optional based on camera module design.
IMX274 also need external 24Mhz clock and is optional based on
camera module design.
This patch adds support for IMX274 power on and off to enable and
disable these supplies and external clock.
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sensor should already be in standby during remove and there is no
need to configure sensor registers for stream stop.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As per Sony IMX274 Y_OUT_SIZE should be the height of effective
image output from the sensor which are the actual total lines
sent over MIPI CSI to receiver.
So, Y_OUT_SIZE should be same as crop height and this patch fixes it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The minimal valid exposure value should be 4 lines instead of 8 for
ov2740 mannual exposure control.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If driver is built without ACPI, the struct acpi_device_id won't be
used:
drivers/media/i2c/imx355.c:1836:36: warning:
'imx355_acpi_ids' defined but not used [-Wunused-const-variable=]
[Sakari Ailus: Added a space before __maybe_unused]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If driver is built without ACPI, the struct acpi_device_id won't be
used:
drivers/media/i2c/imx319.c:2536:36: warning:
'imx319_acpi_ids' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences. White at it, use 'dev' directly instead of 'imx290->dev'.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
tvp7002.c: In function 'tvp7002_g_register':
tvp7002.c:691:11: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
691 | reg->val = val;
| ~~~~~~~~~^~~~~
Just return without setting 'reg' if tvp7002_read returns an error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
struct s5k5baf_fw ends with this:
struct {
u16 id;
u16 offset;
} seq[0];
u16 data[];
};
which is rather confusing and can cause gcc warnings:
s5k5baf.c: In function 's5k5baf_load_setfile.isra':
s5k5baf.c:390:13: warning: array subscript 65535 is outside the bounds of an interior zero-length array 'struct <anonymous>[0]' [-Wzero-length-bounds]
390 | if (f->seq[i].offset + d <= end)
| ~~~~~~^~~
It turns out that 'data[]' is used in only one place and it can
easily be replaced by &fw->seq[0].id and 'seq[0]' can be replaced by
'seq[]'.
This is both more readable and solved that warnings.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
tc358743_cec_isr is misnammed, it is not the main isr.
So rename it to be consistent with its siblings,
tc358743_cec_handler.
It also does not check if its input parameter 'handled' is
is non NULL like its siblings, so add a check.
Fixes: a0ec8d1dc4 ("media: tc358743: add CEC support")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
clang static analysis flags this error
tc358743.c:1468:9: warning: Branch condition evaluates
to a garbage value
return handled ? IRQ_HANDLED : IRQ_NONE;
^~~~~~~
handled should be initialized to false.
Fixes: d747b806ab ("[media] tc358743: add direct interrupt handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OV8856 supports 3264x2448 @ 30 FPS, which is added
in this commit.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OV8856 supports 1632x1224 @ 60 FPS, which is added
in this commit.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_async_notifier_add_subdev() requires the asd to be allocated
dynamically, but the max9286 driver embeds it in the max9286_source
structure. This causes memory corruption when the notifier is destroyed
at remove time with v4l2_async_notifier_cleanup().
Fix this issue by registering the asd with
v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically
internally. A new max9286_asd structure is introduced, to store a
pointer to the corresonding max9286_source that needs to be accessed
from bound and unbind callbacks. There's no need to take an extra
explicit reference to the fwnode anymore as
v4l2_async_notifier_add_fwnode_subdev() does so internally.
While at it, use %u instead of %d to print the unsigned index in the
error message from the v4l2_async_notifier_add_fwnode_subdev() error
path.
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
During testing this sensor on iW-RainboW-G21D-Qseven platform in 8-bit DVP
mode with rcar-vin bridge noticed the capture worked fine for the first run
(with yavta), but for subsequent runs the bridge driver waited for the
frame to be captured. Debugging further noticed the data lines were
enabled/disabled in stream on/off callback and dumping the register
contents 0x3017/0x3018 in ov5640_set_stream_dvp() reported the correct
values, but yet frame capturing failed.
To get around this issue data lines are enabled in s_power callback.
(Also the sensor remains in power down mode if not streaming so power
consumption shouldn't be affected)
Fixes: f22996db44 ("media: ov5640: add support of DVP parallel interface")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for adding DVP configuration in s_power callback
move mipi configuration into separate function
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Keep the sensor in software power down mode and wake up only in
ov5640_set_stream_dvp() callback.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Alan Chiang's e-mail address no longer works. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9VerweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhc4H/iHD6qLdB36gZB6K
oc2nJyrqyWitv4ti2Mnt5PA7o4wX4l6nnr1QvoaJ4BRs5Ja1czRvb2XDmdzqAoIA
xITGoafqaAeDfxQ91bWrJsVN0pCRKiGwddXlU7TWmqw/riAkfOqi6GYKvav4biJH
+n1mUPQb1M2IbRFsqkAS+ebKHq3CWaRvzKOEneS88nGlL5u31S9NAru8Ru/fkxRn
6CwGcs1XRaBPYaZAhdfIb0NuatUlpkhPC9yhNS9up6SqrWmK3m65vmFVng6H0eCF
fwn1jVztboY/XcNAi5sM9ExpQCql6WLQEEktVikqRDojC8fVtSx6W55tPt7qeaoO
Z6t4/DA=
=bcA4
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc4' into patchwork
Linux 5.9-rc4
* tag 'v5.9-rc4': (1001 commits)
Linux 5.9-rc4
io_uring: fix linked deferred ->files cancellation
io_uring: fix cancel of deferred reqs with ->files
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
mm/khugepaged.c: fix khugepaged's request size in collapse_file
mm/hugetlb: fix a race between hugetlb sysctl handlers
mm/hugetlb: try preferred node first when alloc gigantic page from cma
mm/migrate: preserve soft dirty in remove_migration_pte()
mm/migrate: remove unnecessary is_zone_device_page() check
mm/rmap: fixup copying of soft dirty and uffd ptes
mm/migrate: fixup setting UFFD_WP flag
mm: madvise: fix vma user-after-free
checkpatch: fix the usage of capture group ( ... )
fork: adjust sysctl_max_threads definition to match prototype
ipc: adjust proc_ipc_sem_dointvec definition to match prototype
mm: track page table modifications in __apply_to_page_range()
MAINTAINERS: IA64: mark Status as Odd Fixes only
MAINTAINERS: add LLVM maintainers
MAINTAINERS: update Cavium/Marvell entries
mm: slub: fix conversion of freelist_corrupted()
...
rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.
Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.
Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.
This affects:
- rx_resolution member of struct rc_dev
- timeout member of struct rc_dev
- duration member in struct ir_raw_event
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The unit of exposure value is different from other OmniVision sensors,
driver will divide by 2 before set register, the exposure range exposed
by v4l2 ctrl to user should be same as others, so the calculation for
the maximum exposure value in current driver need be fixed.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make use of SCCB APIs for regmap operations.
Remove i2c_check_functionality as devm_regmap_init_sccb
does it for us.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
