Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: tct_hammer_defconfig arm):
drivers/usb/gadget/udc/s3c2410_udc.c:314:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/usb/gadget/udc/s3c2410_udc.c:418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190805191426.GA12414@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: at91_dt_defconfig arm):
drivers/usb/gadget/udc/atmel_usba_udc.c:329:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190805184842.GA8627@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from DWC_usb31 version 1.90a and later, the DCTL.CSFRST bit
will not be cleared until after all the internal clocks are synchronized
during soft-reset. This may take a little more than 50ms. Set the
polling rate at 20ms instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This enum is only used in drivers/usb/dwc3/dwc3-omap3.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use use device_property_count_u32() directly, that makes code neater.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When a gadget is disabled, kill_all_requests() can be called
simultaneously from both a user process via dwc2_hsotg_pullup() and from
the interrupt handler if the hardware detects disconnection.
Since we drop the lock in dwc2_hsotg_complete_request() in order to call
the completion handler, this means that the list is modified
concurrently and leads to an infinite loop in kill_all_requests().
Replace the foreach loop with a while-not-empty loop in order to remove
the danger of this concurrent modification.
Note: I observed this with threadirqs, I'm not sure if it can be
triggered without threaded interrupts.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: at91_dt_defconfig arm):
drivers/usb/gadget/udc/atmel_usba_udc.c:329:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: tct_hammer_defconfig arm):
drivers/usb/gadget/udc/s3c2410_udc.c:314:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/usb/gadget/udc/s3c2410_udc.c:418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently, the authorized_default and interface_authorized_default
attributes for HCD are set up after the uevent has been sent to userland.
This creates a race condition where userland may fail to access this
file when processing the event. Move the appending of these attributes
earlier relying on the usb_bus_notify dispatcher.
Signed-off-by: Thiébaud Weksteen <tweek@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190806110050.38918-1-tweek@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have to drop the mutex before we close() upon disconnect()
as close() needs the lock. This is safe to do by dropping the
mutex as intfdata is already set to NULL, so open() will fail.
Fixes: 03f36e885fc26 ("USB: open disconnect race in iowarrior")
Reported-by: syzbot+a64a382964bf6c71a9c0@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20190808092728.23417-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core now supports the option to automatically create and
remove any needed sysfs attribute files for a driver when the device is
bound/removed from it. Convert the uscsi_ccg code to use that instead
of trying to create sysfs files "by hand".
Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190805193636.25560-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Acked-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20190805193636.25560-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UWB and wusbcore code is long obsolete, so let us just move the code
out of the real part of the kernel and into the drivers/staging/
location with plans to remove it entirely in a few releases.
Link: https://lore.kernel.org/r/20190806101509.GA11280@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core supports dev_groups for individual drivers,
expose that pointer to struct usb_device_driver to make it easier for USB
drivers to also use it.
Yes, users of usb_device_driver are much rare, but there are instances
already that use custom sysfs files, so adding this support will make
things easier for those drivers. usbip is one example, hubs might be
another one.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190806144502.17792-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core supports dev_groups for individual drivers,
expose that pointer to struct usb_driver to make it easier for USB
drivers to also use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190806144502.17792-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190805193636.25560-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon an error within proc_do_submiturb(), dec_usb_memory_use_count()
gets called once by the error handling tail and again by free_async().
Remove the first call.
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190804235044.22327-1-gavinli@thegavinli.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QCA Rome USB Bluetooth controller has several issues once LPM gets
enabled:
- Fails to get enumerated in coldboot. [1]
- Drains more power (~ 0.2W) when the system is in S5. [2]
- Disappears after a warmboot. [2]
The issue happens because the device lingers at LPM L1 in S5, so device
can't get enumerated even after a reboot.
Disable LPM at shutdown to solve the issue.
[1] https://bugs.launchpad.net/bugs/1757218
[2] https://patchwork.kernel.org/patch/10607097/
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190805142412.23965-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190802130408.20336-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM may receive PD messages associated with unknown or unsupported
alternate modes. If that happens, calls to typec_match_altmode()
will return NULL. The tcpm code does not currently take this into
account. This results in crashes.
Unable to handle kernel NULL pointer dereference at virtual address 000001f0
pgd = 41dad9a1
[000001f0] *pgd=00000000
Internal error: Oops: 5 [#1] THUMB2
Modules linked in: tcpci tcpm
CPU: 0 PID: 2338 Comm: kworker/u2:0 Not tainted 5.1.18-sama5-armv7-r2 #6
Hardware name: Atmel SAMA5
Workqueue: 2-0050 tcpm_pd_rx_handler [tcpm]
PC is at typec_altmode_attention+0x0/0x14
LR is at tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm]
...
[<c03fbee8>] (typec_altmode_attention) from [<bf8030fb>]
(tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm])
[<bf8030fb>] (tcpm_pd_rx_handler [tcpm]) from [<c012082b>]
(process_one_work+0x123/0x2a8)
[<c012082b>] (process_one_work) from [<c0120a6d>]
(worker_thread+0xbd/0x3b0)
[<c0120a6d>] (worker_thread) from [<c012431f>] (kthread+0xcf/0xf4)
[<c012431f>] (kthread) from [<c01010f9>] (ret_from_fork+0x11/0x38)
Ignore PD messages if the associated alternate mode is not supported.
Fixes: e9576fe8e605c ("usb: typec: tcpm: Support for Alternate Modes")
Cc: stable <stable@vger.kernel.org>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1564761822-13984-1-git-send-email-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usb core will reset the default control endpoint "ep0" before resetting
a device. if the endpoint has a valid pointer back to the usb device
then the xhci driver reset callback will try to clear the toggle for
the endpoint.
ep0 didn't use to have this pointer set as ep0 was always allocated
by default together with a xhci slot for the usb device. Other endpoints
got their usb device pointer set in xhci_add_endpoint()
This changed with commit ef513be0a905 ("usb: xhci: Add Clear_TT_Buffer")
which sets the pointer for any endpoint on a FS/LS device behind a
HS hub that halts, including ep0.
If xHC controller needs to be reset at resume, then all the xhci slots
will be lost. Slots will be reenabled and reallocated at device reset,
but unlike other endpoints the ep0 is reset before device reset, while
the xhci slot may still be invalid, causing NULL pointer dereference.
Fix it by checking that the endpoint has both a usb device pointer and
valid xhci slot before trying to clear the toggle.
This issue was not seen earlier as ep0 didn't use to have a valid usb
device pointer, and other endpoints were only reset after device reset
when xhci slots were properly reenabled.
Reported-by: Bob Gleitsmann <rjgleits@bellsouth.net>
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Fixes: ef513be0a905 ("usb: xhci: Add Clear_TT_Buffer")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/1564758044-24748-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is connected to the host controller and
the system enters suspend, the following error happens
in xhci_suspend():
xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout
Since the firmware/internal CPU control the USBSTS.STS_HALT
and the process speed is down when the roothub port enters U3,
long delay for the handshake of STS_HALT is neeed in xhci_suspend().
So, this patch adds to set the XHCI_SLOW_SUSPEND.
Fixes: 435cc1138ec9 ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the past, USB PHY handling has been moved in the HCD core. Some
host controller drivers needing more control of the PHYs, they have
been granted the freedom to handle themselves the PHY states and to
prevent the HCD core to do so in commit 4e88d4c08301 ("usb: add a flag
to skip PHY initialization to struct usb_hcd"). With this change, any
USB host controller could set the hcd->skip_phy_initialization flag so
that the HCD core would just skip the PHY initialization sequence.
However, in the USB subsystem, there are currently two entirely
different forms of PHY: one is called 'usb_phy' and is
USB-subsystem-wide, while there is also the generic and kernel-wide
'phy' from the (recent) generic PHY framework.
When the commit above was introduced, both type of PHYs where handled
by the HCD core.
Later, commit bc40f5341741 ("USB: core: hcd: drop support for legacy
phys") removed the support for the former type of PHYs in the HCD
core. These 'usb_phy' are still present though, but managed from the
controller drivers only. Hence, setting the
hcd->skip_phy_initialization flag just because a 'usb_phy' is
initialized by a controller driver is a non-sense.
For instance on Armada CP110, a 'usb_phy' is there to enable the power
supply to the USB host, while there is also a COMPHY block providing
SERDES lanes configuration that is referenced as a PHY from the common
PHY framework.
Right now, users of the xhci-plat.c driver either use a 'usb_phy' only
and do not care about the attempt of generic PHY initialization within
the HCD core (as there is none); or they use a single 'phy' and the
code flow does not pass through the block setting
hcd->skip_phy_initialization anyway.
While there is not users of both PHY types at the same time, drop this
limitation from the xhci-plat.c driver. Note that the tegra driver
probably has the same limitation and could definitely benefit from a
similar change.
Cc: Johan Hovold <johan@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20190731121150.2253-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable ret is being initialized with a value that is never read
and ret is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190731223917.16532-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-47-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/usb/phy/phy-ab8500-usb.c: In function 'ab8500_usb_link_status_update':
drivers/usb/phy/phy-ab8500-usb.c:424:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDB;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:425:2: note: here
case USB_LINK_NOT_CONFIGURED_8500:
^~~~
drivers/usb/phy/phy-ab8500-usb.c:440:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDC;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:441:2: note: here
case USB_LINK_STD_HOST_NC_8500:
^~~~
drivers/usb/phy/phy-ab8500-usb.c:459:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDA;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:460:2: note: here
case USB_LINK_HM_IDGND_8500:
^~~~
drivers/usb/phy/phy-ab8500-usb.c: In function 'ab8505_usb_link_status_update':
drivers/usb/phy/phy-ab8500-usb.c:332:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDB;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:333:2: note: here
case USB_LINK_NOT_CONFIGURED_8505:
^~~~
drivers/usb/phy/phy-ab8500-usb.c:352:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDC;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:353:2: note: here
case USB_LINK_STD_HOST_NC_8505:
^~~~
drivers/usb/phy/phy-ab8500-usb.c:370:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDA;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:371:2: note: here
case USB_LINK_HM_IDGND_8505:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20190729000631.GA24165@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: arm):
drivers/usb/host/ohci-tmio.c: In function ‘tmio_stop_hc’:
./include/linux/device.h:1499:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/ohci-tmio.c:99:4: note: in expansion of macro ‘dev_err’
dev_err(&dev->dev, "Unsupported amount of ports: %d\n", ohci->num_ports);
^~~~~~~
In file included from drivers/usb/host/ohci-hcd.c:1257:0:
drivers/usb/host/ohci-tmio.c💯3: note: here
case 3:
^~~~
drivers/usb/host/ohci-tmio.c:101:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
pm |= CCR_PM_USBPW3;
^
drivers/usb/host/ohci-tmio.c:102:3: note: here
case 2:
^~~~
drivers/usb/host/ohci-tmio.c:103:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
pm |= CCR_PM_USBPW2;
^
drivers/usb/host/ohci-tmio.c:104:3: note: here
case 1:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190729222201.GA19408@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the code for getting generic PHYs from standard device tree array
from the main controller device node. This is a first step in resolving
the conflict between Exynos EHCI/OHCI sub-nodes and generic USB device
bindings. Later the sub-nodes currently used for assigning PHYs to root
ports of the controller will be removed making a place for the generic
USB device bindings nodes.
Suggested-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190726081453.9456-3-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If config tcpm as module, module unload will not remove tcpm dir,
then the next module load will have problem: the rootdir is NULL
but tcpm dir is still there, so tcpm_debugfs_init() will create
tcpm dir again with failure, fix it by remove the tcpm dir if no
children.
Cc: stable@vger.kernel.org # v4.15+
Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging")
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190717080646.30421-2-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logbuffer memory should be freed when remove debug file.
Cc: stable@vger.kernel.org # v4.15+
Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging")
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190717080646.30421-1-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A second regression was found in the immediate data transfer (IDT)
support which was added to 5.2 kernel
IDT is used to transfer small amounts of data (up to 8 bytes) in the
field normally used for data dma address, thus avoiding dma mapping.
If the data was not already dma mapped, then IDT support assumed data was
in urb->transfer_buffer, and did not take into accound that even
small amounts of data (8 bytes) can be in a scatterlist instead.
This caused a NULL pointer dereference when sg_dma_len() was used
with non-dma mapped data.
Solve this by not using IDT if scatter gather buffer list is used.
Fixes: 33e39350ebd2 ("usb: xhci: add Immediate Data Transfer support")
Cc: <stable@vger.kernel.org> # v5.2
Reported-by: Maik Stohn <maik.stohn@seal-one.com>
Tested-by: Maik Stohn <maik.stohn@seal-one.com>
CC: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1564044861-1445-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a partial revert of 73d31def1aab "usb: usb251xb: Create a ports
field collector method", which broke a existing devicetree
(arch/arm64/boot/dts/freescale/imx8mq.dtsi).
There is no reason why the swap-dx-lanes property should not apply to
the upstream port. The reason given in the breaking commit was that it's
inconsitent with respect to other port properties, but in fact it is not.
All other properties which only apply to the downstream ports explicitly
reject port 0, so there is pretty strong precedence that the driver
referred to the upstream port as port 0. So there is no inconsistency in
this property at all, other than the swapping being also applicable to
the upstream port.
CC: stable@vger.kernel.org #5.2
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20190719084407.28041-3-l.stach@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable retval is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed. Also remove a blank
line.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190704150341.759-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't do extra cpu_to_le32 conversion for
put_unaligned_le32 because it is already implemented
in this function.
Fixes sparse error:
xhci-hub.c:1152:44: warning: incorrect type in argument 1 (different base types)
xhci-hub.c:1152:44: expected unsigned int [usertype] val
xhci-hub.c:1152:44: got restricted __le32 [usertype]
Fixes: 395f540 "xhci: support new USB 3.1 hub request to get extended port status"
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1562501839-26522-1-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 518a2f1925c3
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190715032010.7258-1-huangfq.daxian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header, oxu210hp.h is only included from oxu210hp-hcd.c
so squash it.
When I moved the code, I also fixed the following warnings from
scripts/checkpatch.pl:
drivers/usb/host/oxu210hp-hcd.c:117: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:196: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:221: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:266: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:336: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:354: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:385: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:393: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:429: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:432: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:436: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:451: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:461: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:467: warning: please, no space before tabs
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190721144909.5295-2-yamada.masahiro@socionext.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
