This adds support for the following PEAK-System CAN FD interfaces:
PCAN-cPCIe FD CAN FD Interface for cPCI Serial (2 or 4 channels)
PCAN-PCIe/104-Express CAN FD Interface for PCIe/104-Express (1, 2 or 4 ch.)
PCAN-miniPCIe FD CAN FD Interface for PCIe Mini (1, 2 or 4 channels)
PCAN-PCIe FD OEM CAN FD Interface for PCIe OEM version (1, 2 or 4 ch.)
PCAN-M.2 CAN FD Interface for M.2 (1 or 2 channels)
Like the PCAN-PCIe FD interface, all of these boards run the same IP Core
that is able to handle CAN FD (see also http://www.peak-system.com).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
SUN4Is CAN IP has a 64 byte deep FIFO buffer. If the buffer is not
drained fast enough (overrun) it's getting mangled. Already received
frames are dropped - the data can't be restored.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The D_CAN controller doesn't provide a triple sampling mode, so don't set
the CAN_CTRLMODE_3_SAMPLES flag in ctrlmode_supported. Currently enabling
triple sampling is a no-op.
Signed-off-by: Richard Schütz <rschuetz@uni-koblenz.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.6
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This reverts commit baedf68a06.
There is an updated version of this fix which covers
the problem more thoroughly.
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding miimon logic has a flaw, in that a failure of the
rtnl_trylock can cause a slave to become permanently stuck in
BOND_LINK_FAIL state.
The sequence of events to cause this is as follows:
1) bond_miimon_inspect finds that a slave's link is down, and so
calls bond_propose_link_state, setting slave->new_link_state to
BOND_LINK_FAIL, then sets slave->new_link to BOND_LINK_DOWN and returns
non-zero.
2) In bond_mii_monitor, the rtnl_trylock fails, and the timer is
rescheduled. No change is committed.
3) bond_miimon_inspect is called again, but this time the slave
from step 1 has recovered. slave->new_link is reset to NOCHANGE, and, as
slave->link was never changed, the switch enters the BOND_LINK_UP case,
and does nothing. The pending BOND_LINK_FAIL state from step 1 remains
pending, as new_link_state is not reset.
4) The state from step 3 persists until another slave changes link
state and causes bond_miimon_inspect to return non-zero. At this point,
the BOND_LINK_FAIL state change on the slave from steps 1-3 is committed,
and the slave will remain stuck in BOND_LINK_FAIL state even though it
is actually link up.
The remedy for this is to initialize new_link_state on each entry
to bond_miimon_inspect, as is already done with new_link.
Fixes: fb9eb899a6 ("bonding: handle link transition from FAIL to UP correctly")
Reported-by: Alex Sidorenko <alexandre.sidorenko@hpe.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 07f4c90062 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), we will try to use even ports for connect(). Then if an
application (seen clearly with iperf) opens multiple streams to the same
destination IP and port, each stream will be given an even source port.
So the bonding driver's simple xmit_hash_policy based on layer3+4 addressing
will always hash all these streams to the same interface. And the total
throughput will limited to a single slave.
Change the tcp code will impact the whole tcp behavior, only for bonding
usage. Paolo Abeni suggested fix this by changing the bonding code only,
which should be more reasonable, and less impact.
Fix this by discarding the lowest hash bit because it contains little entropy.
After the fix we can re-balance between slaves.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hn is being kfree'd in mlx5e_del_l2_from_hash and then dereferenced
by accessing hn->ai.addr
Fix this by copying the MAC address into a local variable for its safe use
in all possible execution paths within function mlx5e_execute_l2_action.
Addresses-Coverity-ID: 1417789
Fixes: eeb66cdb68 ("net/mlx5: Separate between E-Switch and MPFS")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.63.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully this is the last batch of networking fixes for 4.14
Fingers crossed...
1) Fix stmmac to use the proper sized OF property read, from Bhadram
Varka.
2) Fix use after free in net scheduler tc action code, from Cong
Wang.
3) Fix SKB control block mangling in tcp_make_synack().
4) Use proper locking in fib_dump_info(), from Florian Westphal.
5) Fix IPG encodings in systemport driver, from Florian Fainelli.
6) Fix division by zero in NV TCP congestion control module, from
Konstantin Khlebnikov.
7) Fix use after free in nf_reject_ipv4, from Tejaswi Tanikella"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: systemport: Correct IPG length settings
tcp: do not mangle skb->cb[] in tcp_make_synack()
fib: fib_dump_info can no longer use __in_dev_get_rtnl
stmmac: use of_property_read_u32 instead of read_u8
net_sched: hold netns refcnt for each action
net_sched: acquire RTNL in tc_action_net_exit()
net: vrf: correct FRA_L3MDEV encode type
tcp_nv: fix division by zero in tcpnv_acked()
netfilter: nf_reject_ipv4: Fix use-after-free in send_reset
netfilter: nft_set_hash: disable fast_ops for 2-len keys
Due to a documentation mistake, the IPG length was set to 0x12 while it
should have been 12 (decimal). This would affect short packet (64B
typically) performance since the IPG was bigger than necessary.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.
This causes it to always return 0 with little-endian
architectures.
Fix it by using of_property_read_u32() OF API.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FRA_L3MDEV is defined as U8, but is being added as a U32 attribute. On
big endian architecture, this results in the l3mdev entry not being
added to the FIB rules.
Fixes: 1aa6c4f6b8 ("net: vrf: Add l3mdev rules on first device create")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It fixes a problem for the last chunk where 'chunk_size' is smaller than
MLXSW_I2C_BLK_MAX and data is copied to the wrong offset, overriding
previous data.
Fixes: 6882b0aee1 ("mlxsw: Introduce support for I2C bus")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIC has the ability to generate events whenever a sensor indicates
the temperature goes above or below its high or low thresholds,
respectively.
In new firmware versions the firmware enforces a minimum of 5
degrees Celsius difference between both thresholds. Make the driver
conform to this requirement.
Note that this is required even when the events are disabled, as in
certain systems interrupts are generated via GPIO based on these
thresholds.
Fixes: 85926f8770 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function of_parse_phandle() returns a NULL pointer if it cannot
resolve a phandle property to a device_node pointer. In function
hns_nic_dev_probe(), its return value is passed to PTR_ERR to extract
the error code. However, in this case, the extracted error code will
always be zero, which is unexpected.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function netdev_priv() returns the private data of the device. The
memory to store the private data is allocated in alloc_netdev() and is
released in netdev_free(). Calling kfree() on the return value of
netdev_priv() after netdev_free() results in a double free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
uncovered another bug in the Marvell PHY driver, which broke the
Marvell OpenRD platform. It relies on the bootloader configuring the
RGMII delays and does not specify a phy-mode in its device tree. The
PHY driver should only configure RGMII delays if the phy mode
indicates it is using RGMII. Without anything in device tree, the
mv643xx Ethernet driver defaults to GMII.
Fixes: 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most important here is the security vulnerabitility fix for
ath10k.
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ+JEXAAoJEG4XJFUm622bxlYH/RVFveiBV/5v3Edj7bfQaonm
DrSO9fWNi+B3d2S0jpP/E9aPAZFfI6lrJ2zYbmyHEtIgLmWUsCgpkPbsTiE7Qa/7
VesLt5cDQyE25F9C3N2cNgaSI2VrHVml13GZ1f9329us/pUyPhzT7SKVO5c3SIjf
PcnyobgRtT42tJWYGDJ83tP9EaGQnIcxVcjrH5Bfp7SiOLlWh05owDBQKyxni+8Q
NAF/CAqaeXOTygL8f/A4mmp/qAolPzSp3XpyFWNOP3UdfI+sgLNbc8BDo1COzHMw
of9SF0RZi8Vy65x9xZKwxnzkmUmp0F7GX/MpkO2vI9Zhca8XlXCVb30t6pDqSLc=
=iqP1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
The most important here is the security vulnerabitility fix for
ath10k.
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git fixes for 4.14. Major changes:
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
Thorsten reported on <fa6e3ee2-91b5-a54b-afe3-87f30aac7a48@leemhuis.info> that
commit c9353bf483 made ath10k unstable with QCA6174 on his Dell XPS13 (9360)
with an error message:
ath10k_pci 0000:3a:00.0: failed to extract amsdu: -11
It only seemed to happen with certain APs, not all, but when it happened the
only way to get ath10k working was to switch the wifi off and on with a hotkey.
As this commit made things even worse (a warning vs breaking the whole
connection) let's revert the commit for now and while the issue is being fixed.
Link: http://lists.infradead.org/pipermail/ath10k/2017-October/010227.html
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx data frames notified through HTT_T2H_MSG_TYPE_RX_IND and
HTT_T2H_MSG_TYPE_RX_FRAG_IND expect PN/TSC check to be done
on host (mac80211) rather than firmware. Rebuild cipher header
in every received data frames (that are notified through those
HTT interfaces) from the rx_hdr_status tlv available in the
rx descriptor of the first msdu. Skip setting RX_FLAG_IV_STRIPPED
flag for the packets which requires mac80211 PN/TSC check support
and set appropriate RX_FLAG for stripped crypto tail. Hw QCA988X,
QCA9887, QCA99X0, QCA9984, QCA9888 and QCA4019 currently need the
rebuilding of cipher header to perform PN/TSC check for replay
attack.
Please note that removing crypto tail for CCMP-256, GCMP and GCMP-256 ciphers
in raw mode needs to be fixed. Since Rx with these ciphers in raw
mode does not work in the current form even without this patch and
removing crypto tail for these chipers needs clean up, raw mode related
issues in CCMP-256, GCMP and GCMP-256 can be addressed in follow up
patches.
Tested-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The commit 9a393b5d59 ("tap: tap as an independent module") created a
separate tap module that implements tap functionality and exports
interfaces that will be used by macvtap and ipvtap modules to create
create respective tap devices.
However, that patch introduced a regression wherein the modules macvtap
and ipvtap can be removed (through modprobe -r) while there are
applications using the respective /dev/tapX devices. These applications
cause kernel to hold reference to /dev/tapX through 'struct cdev
macvtap_cdev' and 'struct cdev ipvtap_dev' defined in macvtap and ipvtap
modules respectively. So, when the application is later closed the
kernel panics because we are referencing KVA that is present in the
unloaded modules.
----------8<------- Example ----------8<----------
$ sudo ip li add name mv0 link enp7s0 type macvtap
$ sudo ip li show mv0 |grep mv0| awk -e '{print $1 $2}'
14:mv0@enp7s0:
$ cat /dev/tap14 &
$ lsmod |egrep -i 'tap|vlan'
macvtap 16384 0
macvlan 24576 1 macvtap
tap 24576 3 macvtap
$ sudo modprobe -r macvtap
$ fg
cat /dev/tap14
^C
<...system panics...>
BUG: unable to handle kernel paging request at ffffffffa038c500
IP: cdev_put+0xf/0x30
----------8<-----------------8<----------
The fix is to set cdev.owner to the module that creates the tap device
(either macvtap or ipvtap). With this set, the operations (in
fs/char_dev.c) on char device holds and releases the module through
cdev_get() and cdev_put() and will not allow the module to unload
prematurely.
Fixes: 9a393b5d59 (tap: tap as an independent module)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An unaligned alloc_frag->offset caused by previous allocation will
result an unaligned skb->head. This will lead unaligned
skb_shared_info and then unaligned dataref which requires to be
aligned for accessing on some architecture. Fix this by aligning
alloc_frag->offset before the frag refilling.
Fixes: 0bbd7dad34 ("tun: make tun_build_skb() thread safe")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Wei Wei <dotweiba@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reported-by: Wei Wei <dotweiba@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-10-26
This series contains fixes to e1000, igb, ixgbe and i40e.
Vincenzo Maffione fixes a potential race condition which would result in
the interface being up but transmits are disabled in the hardware.
Colin Ian King fixes a possible NULL pointer dereference in e1000, which
was found by Coverity.
Jean-Philippe Brucker fixes a possible kernel panic when a driver cannot
map a transmit buffer, which is caused by an erroneous test.
Alex provides a fix for ixgbe, which is a partial revert of the commit
ffed21bcee ("ixgbe: Don't bother clearing buffer memory for descriptor rings")
because the previous commit messed up the exception handling path by
adding the count back in when we did not need to. Also fixed a typo,
where the transmit ITR setting was being used to determine if we were
using adaptive receive interrupt moderation or not. Lastly, fixed a
memory leak by including programming descriptors in the cleaned count.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to DWMAC databook the first queue operating mode
must always be in DCB.
As MTL_QUEUE_DCB = 1, we need to always set the first queue
operating mode to DCB otherwise driver will think that queue
is in AVB mode (because MTL_QUEUE_AVB = 0).
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to DT bindings documentation we are expecting a
property called "snps,read-requests" but we are parsing
instead a property called "read,read-requests".
This is clearly a typo. Fix it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No rcu_read_lock is called, but rcu_read_unlock is still called.
Thus rcu_read_unlock should be removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-10-26
The series includes some misc fixes for mlx5 core and etherent driver.
Please pull and let me know if there's any problem.
For -Stable:
net/mlx5e: Properly deal with encap flows add/del under neigh update (kernels >= 4.12)
net/mlx5: Fix health work queue spin lock to IRQ safe (kernels >= 4.13)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the i40e driver to include programming descriptors in
the cleaned_count. Without this change it becomes possible for us to leak
memory as we don't trigger a large enough allocation when the time comes to
allocate new buffers and we end up overwriting a number of rx_buffers equal
to the number of programming descriptors we encountered.
Fixes: 0e626ff7cc ("i40e: Fix support for flow director programming status")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It looks like there was either a copy/paste error or just a typo that
resulted in the Tx ITR setting being used to determine if we were using
adaptive Rx interrupt moderation or not.
This patch fixes the typo.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a partial revert of "ixgbe: Don't bother clearing buffer
memory for descriptor rings". Specifically I messed up the exception
handling path a bit and this resulted in us incorrectly adding the count
back in when we didn't need to.
In order to make this simpler I am reverting most of the exception handling
path change and instead just replacing the bit that was handled by the
unmap_and_free call.
Fixes: ffed21bcee ("ixgbe: Don't bother clearing buffer memory for descriptor rings")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver cannot map a TX buffer, instead of rolling back
gracefully and retrying later, we currently get a panic:
[ 159.885994] igb 0000:00:00.0: TX DMA map failed
[ 159.886588] Unable to handle kernel paging request at virtual address ffff00000a08c7a8
...
[ 159.897031] PC is at igb_xmit_frame_ring+0x9c8/0xcb8
Fix the erroneous test that leads to this situation.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the stat type is invalid then data[i] is being set
either by dereferencing a null pointer p, or it is reading from
an incorrect previous location if we had a valid stat type
previously. Fix this by skipping over the read of p on an invalid
stat type.
Detected by CoverityScan, CID#113385 ("Explicit null dereferenced")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a race condition that can result into the interface being
up and carrier on, but with transmits disabled in the hardware.
The bug may show up by repeatedly IFF_DOWN+IFF_UP the interface, which
allows e1000_watchdog() interleave with e1000_down().
CPU x CPU y
--------------------------------------------------------------------
e1000_down():
netif_carrier_off()
e1000_watchdog():
if (carrier == off) {
netif_carrier_on();
enable_hw_transmit();
}
disable_hw_transmit();
e1000_watchdog():
/* carrier on, do nothing */
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double free of skb_array in tap module is causing kernel panic. When
tap_set_queue() fails we free skb_array right away by calling
skb_array_cleanup(). However, later on skb_array_cleanup() is called
again by tap_sock_destruct through sock_put(). This patch fixes that
issue.
Fixes: 362899b872 (macvtap: switch to use skb array)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlnvHlATHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9tBJB/9sLLdYdtrp0L1KlJ+PNVjNcq993ai4
6wlh0ay+JKiMZzepkEEYjI8lFdFVxmvB9czOL3FgV6Cb2tW7/vTs3gtv1LuvA92o
9QsOXQtH/KO+bbuPiHPRvuSMO56OMZtxrJSK0prdkodOimDWwnkLZ4jHStNjvmIt
wuE4fYH8K9jp80qtyQ9Al0COvR+ePZtfaDWn3YhO0swEUfcClALl2OqUd2MRl3Ut
dkfbCoGCR7PNnFDNxPACoOu0FLUl01iLDf5fWx43SLKwFhnjf6eomkukyBTzrBT4
bHsPT4hYMkkA+YCQ5TmTDlK6IRwXfvIkgSimFItFE+t+0Rfr2XFIrnps
=IxfN
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.14-20171024' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-10-24
here's another pull request for net/master.
The patch by Gerhard Bertelsmann fixes the CAN_CTRLMODE_LOOPBACK in the
sun4i driver. Two patches by Jimmy Assarsson for the kvaser_usb driver
fix a print in the error path of the kvaser_usb_close() and remove a
wrong warning message with the Leaf v2 firmware version v4.1.844.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces GFP_KERNEL by GFP_ATOMIC to avoid sleeping in the
ndo_set_rx_mode() call which is called with BH disabled.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling mvpp2_prs_mac_multi_set() from mvpp2_prs_mac_init(), two
parameters (the port index and the table index) are inverted. Fixes
this.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo in the mvpp2_prs_tcam_data_cmp() function, as
the shift value is inverted with the data.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, tc with ets type and zero bandwidth is not accepted
by driver. This behavior does not follow the IEEE802.1qaz spec.
If there are tcs with ets type and zero bandwidth, these tcs are
assigned to the lowest priority tc_group #0. We equally distribute
100% bw of the tc_group #0 to these zero bandwidth ets tcs.
Also, the non zero bandwidth ets tcs are assigned to tc_group #1.
If there is no zero bandwidth ets tc, the non zero bandwidth ets tcs
are assigned to tc_group #0.
Fixes: cdcf11212b ("net/mlx5e: Validate BW weight values of ETS")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, the encap action offload is handled in the actions parse
function and not in mlx5e_tc_add_fdb_flow() where we deal with all
the other aspects of offloading actions (vlan, modify header) and
the rule itself.
When the neigh update code (mlx5e_tc_encap_flows_add()) recreates the
encap entry and offloads the related flows, we wrongly call again into
mlx5e_tc_add_fdb_flow(), this for itself would cause us to handle
again the offloading of vlans and header re-write which puts things
in non consistent state and step on freed memory (e.g the modify
header parse buffer which is already freed).
Since on error, mlx5e_tc_add_fdb_flow() detaches and may release the
encap entry, it causes a corruption at the neigh update code which goes
over the list of flows associated with this encap entry, or double free
when the tc flow is later deleted by user-space.
When neigh update (mlx5e_tc_encap_flows_del()) unoffloads the flows related
to an encap entry which is now invalid, we do a partial repeat of the eswitch
flow removal code which is wrong too.
To fix things up we do the following:
(1) handle the encap action offload in the eswitch flow add function
mlx5e_tc_add_fdb_flow() as done for the other actions and the rule itself.
(2) modify the neigh update code (mlx5e_tc_encap_flows_add/del) to only
deal with the encap entry and rules delete/add and not with any of
the other offloaded actions.
Fixes: 232c001398 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
