Normal mixed bag of new device support with continuing trend that most new
devices are supported by extending existing drivers - a positive sign perhaps
that device manufacturers have somewhat stabilized their interfaces across
product generations. The BNO055 driver was however a substantial addition
including several additions to the IIO core.
There are a number of significant patch sets under review, so if the 6.0
cycle runs long I may send a 3rd pull request.
New device support
* adi,adxl313
- Support for the ADXL312 and ADXL314 accelerometers.
* bosch,bmp280
- Support for the BMP380 family of pressures sensors.
Included considerable refactoring and modernization of the bmp280
driver.
* bosch,bno055
- New driver for this i2c/serial attached complex IMU.
* lltc,ltc2497
- Support for the LTC2499 16 channel, 24bit ADC.
* st,pressure
- Support for the LPS22DF pressure sensor
* st,lsm6dsx
- Support for the LSM6DSTX (Mainly adding the ID and WAI)
Features
* core - to support the bosch,bno055 requirements
- Support for linear acceleration channel type (effect of gravity removed)
- Pitch, yaw and roll modifiers for angle channels.
- Standard serialnumber attribute documentation.
- Binary attributes - to allow for calibration save and restore.
* adi,ad7923
- Support extended range (wider supported input voltage range).
* bosch,bmp280
- Add filter controls for some supported parts.
* microchip,mcp3911
- Buffered capture support for this ADC.
- Data ready interrupt support, including hiz control for line.
- Oversampling ratio support.
* st,stm32-adc
- Support ID registers on parts where they are present, providing
discoverability of some features.
Fixes - late breaking fixes that I judged could wait for the merge window.
* adi,ad5593r
- Add a missing STOP condition between address write and data read.
- Check for related i2c functionality.
* adi,ad7923
- Fix shift reporting for some variants supported by the driver.
* infinion,dps310
- Work around a hardware issue where a chip can hang by adding a
timeout and reset path.
Cleanups
* Continuing work to switch to new pm macros.
* MAINTAINERS
- Drop duplication of wild card covered entry in ADI block and
add missing entries to cover ltc294x binding files.
* bosch,bma400
- Fix trivial smatch warning.
* bosch,bmp280
- Fix broken links to datasheets
* lltc,ltc2497
- Fix missing entry for ltc2499
* mexelis,mlx90614
- Switch to get_avail() callback for _available attributes.
* microchip,mcp3911
- Move to devm_ resource management for all elements of probe()
-----BEGIN PGP SIGNATURE-----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=q/TD
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.1b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 6.1 cycle.
Normal mixed bag of new device support with continuing trend that most new
devices are supported by extending existing drivers - a positive sign perhaps
that device manufacturers have somewhat stabilized their interfaces across
product generations. The BNO055 driver was however a substantial addition
including several additions to the IIO core.
There are a number of significant patch sets under review, so if the 6.0
cycle runs long I may send a 3rd pull request.
New device support
* adi,adxl313
- Support for the ADXL312 and ADXL314 accelerometers.
* bosch,bmp280
- Support for the BMP380 family of pressures sensors.
Included considerable refactoring and modernization of the bmp280
driver.
* bosch,bno055
- New driver for this i2c/serial attached complex IMU.
* lltc,ltc2497
- Support for the LTC2499 16 channel, 24bit ADC.
* st,pressure
- Support for the LPS22DF pressure sensor
* st,lsm6dsx
- Support for the LSM6DSTX (Mainly adding the ID and WAI)
Features
* core - to support the bosch,bno055 requirements
- Support for linear acceleration channel type (effect of gravity removed)
- Pitch, yaw and roll modifiers for angle channels.
- Standard serialnumber attribute documentation.
- Binary attributes - to allow for calibration save and restore.
* adi,ad7923
- Support extended range (wider supported input voltage range).
* bosch,bmp280
- Add filter controls for some supported parts.
* microchip,mcp3911
- Buffered capture support for this ADC.
- Data ready interrupt support, including hiz control for line.
- Oversampling ratio support.
* st,stm32-adc
- Support ID registers on parts where they are present, providing
discoverability of some features.
Fixes - late breaking fixes that I judged could wait for the merge window.
* adi,ad5593r
- Add a missing STOP condition between address write and data read.
- Check for related i2c functionality.
* adi,ad7923
- Fix shift reporting for some variants supported by the driver.
* infinion,dps310
- Work around a hardware issue where a chip can hang by adding a
timeout and reset path.
Cleanups
* Continuing work to switch to new pm macros.
* MAINTAINERS
- Drop duplication of wild card covered entry in ADI block and
add missing entries to cover ltc294x binding files.
* bosch,bma400
- Fix trivial smatch warning.
* bosch,bmp280
- Fix broken links to datasheets
* lltc,ltc2497
- Fix missing entry for ltc2499
* mexelis,mlx90614
- Switch to get_avail() callback for _available attributes.
* microchip,mcp3911
- Move to devm_ resource management for all elements of probe()
* tag 'iio-for-6.1b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (57 commits)
iio: adc: mcp3911: add support for oversampling ratio
dt-bindings: iio: adc: mcp3911: add microchip,data-ready-hiz entry
iio: adc: mcp3911: add support for interrupts
iio: adc: mcp3911: add support for buffers
iio: adc: mcp3911: use resource-managed version of iio_device_register
iio: accel: bma400: Fix smatch warning based on use of unintialized value.
iio: light: st_uvis25: Use EXPORT_NS_SIMPLE_DEV_PM_OPS()
iio: accel: bmi088: Use EXPORT_NS_GPL_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: proximity: srf04: Use pm_ptr() to remove unused struct dev_pm_ops
iio: proximity: sx9360: Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
iio: proximity: sx9324: Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
iio: proximity: sx9310: Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
docs: iio: add documentation for BNO055 driver
iio: imu: add BNO055 I2C driver
iio: imu: add BNO055 serdev driver
dt-bindings: iio/imu: Add Bosch BNO055
iio: document "serialnumber" sysfs attribute
iio: document bno055 private sysfs attributes
iio: imu: add Bosch Sensortec BNO055 core driver
iio: add support for binary attributes
...
U-Boot stores its setup as environment variables. It's a list of
key-value pairs stored on flash device with a custom header.
This commit adds an NVMEM driver that:
1. Provides NVMEM access to environment vars binary data
2. Extracts variables as NVMEM cells
Current Linux's NVMEM sysfs API allows reading whole NVMEM data block.
It can be used by user-space tools for reading U-Boot env vars block
without the hassle of finding its location. Parsing will still need to
be re-done there.
Kernel-parsed NVMEM cells can be read however by Linux drivers. This may
be useful for Ethernet drivers for reading device MAC address which is
often stored as U-Boot env variable.
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220916122100.170016-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the MAINTAINERS file to include the path for the LTC2497
and LTC2496 devicetree bindings documentation.
Signed-off-by: Ciprian Regus <ciprian.regus@analog.com>
Link: https://lore.kernel.org/r/20220916140922.2506248-4-ciprian.regus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove the specific entry for ad5758, since
Documentation/devicetree/bindings/iio/*/adi,* already matches
the path.
Signed-off-by: Ciprian Regus <ciprian.regus@analog.com>
Link: https://lore.kernel.org/r/20220916140922.2506248-2-ciprian.regus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- Support new notifier event for device state change through eventfd.
- Add uAPI to retrieve device attestation information for Gaudi2.
- Add uAPI to retrieve the h/w status of all h/w blocks.
- Add uAPI to control the running mode of the engine cores in Gaudi2.
- Expose whether the device runs with secured firmware through the INFO ioctl
and sysfs.
- Support trace events in DMA allocations and MMU map/unmap operations.
- Notify firmware when the device was acquired by a user process and when it
was released. This is done as part of the RAS that the f/w performs.
- Multiple bug fixes, refactors and renames.
- Cleanup of error messages, moving some to debug level.
- Enhance log prints in case of h/w error events for Gaudi2.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE7TEboABC71LctBLFZR1NuKta54AFAmMq7cQACgkQZR1NuKta
54CXRAgAwU82gKSHHU9vFp1gavk9tfPl4OHAhPKk1rBDArzCTMZFynAVGdcx1eSX
XmsqKnjTIcP5dx3BYrHuUWdW79neHnoVvGKCg5+Lh0jG9xdKbeWapJZ6O0eWk3Mx
9VmoAQ/VlyizIoaxfNFi2ou5QhC6DL6AY1+2Vd1mMC1ru5L5Jzq/IIFdNENnxoAa
mTGD0P1EapmzztLbuxH7WYuOPBBhfrTuH1FpGo847QhLcSJ+TDYV7CK1y+uhtEZi
isCX2jigqbQ5UwGcesL80nJM1aYyH6AToCSMrmruIDjVbz1QRqW/s6/8hipOoMW6
o7LhHaoOPj20g2fs+R5Jy7ALXDuiOQ==
=TdfZ
-----END PGP SIGNATURE-----
Merge tag 'misc-habanalabs-next-2022-09-21' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux into char-misc-next
Oded writes:
"This tag contains habanalabs driver changes for v6.1:
- Support new notifier event for device state change through eventfd.
- Add uAPI to retrieve device attestation information for Gaudi2.
- Add uAPI to retrieve the h/w status of all h/w blocks.
- Add uAPI to control the running mode of the engine cores in Gaudi2.
- Expose whether the device runs with secured firmware through the INFO ioctl
and sysfs.
- Support trace events in DMA allocations and MMU map/unmap operations.
- Notify firmware when the device was acquired by a user process and when it
was released. This is done as part of the RAS that the f/w performs.
- Multiple bug fixes, refactors and renames.
- Cleanup of error messages, moving some to debug level.
- Enhance log prints in case of h/w error events for Gaudi2."
* tag 'misc-habanalabs-next-2022-09-21' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux: (68 commits)
habanalabs: eliminate aggregate use warning
habanalabs/gaudi: use 8KB aligned address for TPC kernels
habanalabs: remove some f/w descriptor validations
habanalabs: build ASICs from new to old
habanalabs/gaudi2: allow user to flush PCIE by read
habanalabs: failure to open device due to reset is debug level
habanalabs/gaudi2: Remove unnecessary (void*) conversions
habanalabs/gaudi2: add secured attestation info uapi
habanalabs/gaudi2: add handling to pmmu events in eqe handler
habanalabs/gaudi: change TPC Assert to use TPC DEC instead of QMAN err
habanalabs: rename error info structure
habanalabs/gaudi2: get f/w reset status register dynamically
habanalabs/gaudi2: increase hard-reset sleep time to 2 sec
habanalabs/gaudi2: print RAZWI info upon PCIe access error
habanalabs: MMU invalidation h/w is per device
habanalabs: new notifier events for device state
habanalabs/gaudi2: free event irq if init fails
habanalabs: fix resetting the DRAM BAR
habanalabs: add support for new cpucp return codes
habanalabs/gaudi2: read F/W security indication after hard reset
...
Coresight trace subsystem updates for v6.1 includes:
- Support for HiSilicon PTT trace
- Coresight cleanup of sysfs accessor functions, reduced
code size.
- Expose coresight timestamp source for ETMv4+
- DT binding updates to include missing properties
- Minor documentation, Kconfig text fixes.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
-----BEGIN PGP SIGNATURE-----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=rg+8
-----END PGP SIGNATURE-----
Merge tag 'coresight-next-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux into char-misc-next
Suzuki writes:
"coresight: Changes for v6.1
Coresight trace subsystem updates for v6.1 includes:
- Support for HiSilicon PTT trace
- Coresight cleanup of sysfs accessor functions, reduced
code size.
- Expose coresight timestamp source for ETMv4+
- DT binding updates to include missing properties
- Minor documentation, Kconfig text fixes.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>"
* tag 'coresight-next-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux:
hwtracing: hisi_ptt: Fix up for "iommu/dma: Make header private"
MAINTAINERS: Add maintainer for HiSilicon PTT driver
docs: trace: Add HiSilicon PTT device driver documentation
hwtracing: hisi_ptt: Add tune function support for HiSilicon PCIe Tune and Trace device
hwtracing: hisi_ptt: Add trace function support for HiSilicon PCIe Tune and Trace device
iommu/arm-smmu-v3: Make default domain type of HiSilicon PTT device to identity
coresight: cti-sysfs: Mark coresight_cti_reg_store() as __maybe_unused
coresight: Make new csdev_access offsets unsigned
coresight: cti-sysfs: Re-use same functions for similar sysfs register accessors
coresight: Re-use same function for similar sysfs register accessors
coresight: Simplify sysfs accessors by using csdev_access abstraction
coresight: Remove unused function parameter
coresight: etm4x: docs: Add documentation for 'ts_source' sysfs interface
coresight: etm4x: Expose default timestamp source in sysfs
dt-bindings: arm: coresight-tmc: Add 'iommu' property
dt-bindings: arm: coresight: Add 'power-domains' property
coresight: docs: Fix a broken reference
coresight: trbe: fix Kconfig "its" grammar
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
-----BEGIN PGP SIGNATURE-----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=fUm6
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 6.1
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
* tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (142 commits)
iio: pressure: icp10100: Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS().
iio: adc: max1363: Drop provision to provide an IIO channel map via platform data
iio: accel: bma400: Add support for single and double tap events
iio: Add new event type gesture and use direction for single and double tap
iio: Use per-device lockdep class for mlock
iio: adc: add max11205 adc driver
dt-bindings: iio: adc: Add max11205 documentation file
iio: magnetometer: yamaha-yas530: Use dev_err_probe()
iio: magnetometer: yamaha-yas530: Make strings const in chip info
iio: magnetometer: yamaha-yas530: Use pointers as driver data
iio: adc: tsc2046: silent spi_device_id warning
iio: adc: tsc2046: add vref support
dt-bindings: iio: adc: ti,tsc2046: add vref-supply property
iio: light: ltrf216a: Add raw attribute
dt-bindings: iio: Add missing (unevaluated|additional)Properties on child nodes
MAINTAINERS: fix Analog Devices forum links
iio/accel: fix repeated words in comments
dt-bindings: iio: accel: add dt-binding schema for msa311 accel driver
iio: add MEMSensing MSA311 3-axis accelerometer driver
dt-bindings: vendor-prefixes: add MEMSensing Microsystems Co., Ltd.
...
This patch adds trace events for habanalabs driver to gain all the
benefits such an infrastructure can supply.
The following events were added:
- MMU map/unmap: to be able to track driver's memory allocations
- DMA alloc/free: to track our DMA allocation
the above trace points in conjunction will help us map the device memory
usage as well as to be able to track memory violations.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Acked-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add maintainer for driver and documentation of HiSilicon PTT device.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220816114414.4092-6-yangyicong@huawei.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Add a new entry for VMWARE VSOCK VMCI TRANSPORT DRIVER in the
MAINTAINERS file.
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20220906172722.19862-4-vdasa@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the status from 'Maintained' to 'Supported' for VMWARE
BALLOON DRIVER, VMWARE PVRDMA DRIVER, VMWARE PVSCSI driver,
VMWARE VMCI DRIVER, VMWARE VMMOUSE SUBDRIVER and VMWARE VMXNET3
ETHERNET DRIVER.
This needs to be done to conform to the guidelines in [1].
Maintainers for these drivers are VMware employees.
[1] https://docs.kernel.org/process/maintainers.html
Acked-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20220906172722.19862-3-vdasa@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change 'VMware PVSCSI driver' entry to upper case.
This is a trivial change being done for uniformity.
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20220906172722.19862-2-vdasa@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- MAINTAINERS update
- fix resource leaks in gpio-mockup and gpio-pxa
- add missing locking in gpio-pca953x
- use 32-bit I/O in gpio-realtek-otto
- make irq_chip structures immutable in four more drivers
-----BEGIN PGP SIGNATURE-----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=VkA4
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A a set of fixes from the GPIO subsystem.
Most are small driver fixes except the realtek-otto driver patch which
is pretty big but addresses a significant flaw that can cause the CPU
to stay infinitely busy on uncleared ISR on some platforms.
Summary:
- MAINTAINERS update
- fix resource leaks in gpio-mockup and gpio-pxa
- add missing locking in gpio-pca953x
- use 32-bit I/O in gpio-realtek-otto
- make irq_chip structures immutable in four more drivers"
* tag 'gpio-fixes-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: ws16c48: Make irq_chip immutable
gpio: 104-idio-16: Make irq_chip immutable
gpio: 104-idi-48: Make irq_chip immutable
gpio: 104-dio-48e: Make irq_chip immutable
gpio: realtek-otto: switch to 32-bit I/O
gpio: pca953x: Add mutex_lock for regcache sync in PM
gpio: mockup: remove gpio debugfs when remove device
gpio: pxa: use devres for the clock struct
MAINTAINERS: rectify entry for XILINX GPIO DRIVER
- GT1158 ID added to Goodix touchscreen driver
- Boeder Force Feedback Wheel USB added to iforce joystick driver
- fixup for iforce driver to avoid hangups
- fix autoloading of rk805-pwrkey driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCYxOy5gAKCRBAj56VGEWX
nHe9AQDPTQk4YTBis6QJ6eVd/qnwiBiitKXkmQAKFliJFxrYAQEAs/ykRS3O0DPx
ptGEH2IGnjKSdtVBbfEMUllo52XohQQ=
=t3iB
-----END PGP SIGNATURE-----
Merge tag 'input-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- GT1158 ID added to Goodix touchscreen driver
- Boeder Force Feedback Wheel USB added to iforce joystick driver
- fixup for iforce driver to avoid hangups
- fix autoloading of rk805-pwrkey driver.
* tag 'input-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - add support for Boeder Force Feedback Wheel
Input: iforce - wake up after clearing IFORCE_XMIT_RUNNING flag
Input: goodix - add compatible string for GT1158
MAINTAINERS: add include/dt-bindings/input to INPUT DRIVERS
Input: rk805-pwrkey - fix module autoloading
Input: goodix - add support for GT1158
dt-bindings: input: touchscreen: add compatible string for Goodix GT1158
Add documentation for ublk subsystem. It was supposed to be documented when
merging the driver, but missing at that time.
Cc: Bagas Sanjaya <bagasdotme@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
[axboe: correct MAINTAINERS addition]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
PIO function's auxiliary bus driver enumerates separate child devices for
GPIO controller and OTP/EEPROM interface. This gpio driver implemented
based on the gpio framework is loaded for the gpio auxiliary device.
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220824200047.150308-3-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx is a PCIe switch with a multi-function endpoint on one of its
downstream ports. PIO function is one of the functions in the
multi-function endpoint. PIO function combines a GPIO controller and also
an interface to program pci1xxxx's OTP & EEPROM. This auxiliary bus driver
is loaded for the PIO function and separate child devices are enumerated
for GPIO controller and OTP/EEPROM interface.
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220824200047.150308-2-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0509b270a3 ("scripts/spdxcheck: Put excluded files and directories
into a separate file") moved excluded files to the new file
scripts/spdxexclude, but did not adjust the MAINTAINERS section. The file
scripts/spdxexclude clearly belongs to LICENSES and SPDX stuff.
Add a corresponding file entry.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220825152029.12660-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the links to redirect to the correct forum subsection for the latest
Analog Devices drivers added.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20220824170913.13411-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MSA311 is a tri-axial, low-g accelerometer with I2C digital output for
sensitivity consumer applications. It has dynamic user-selectable full
scales range of +-2g/+-4g/+-8g/+-16g and allows acceleration measurements
with output data rates from 1Hz to 1000Hz.
This driver supports following MSA311 features:
- IIO interface
- Different power modes: NORMAL and SUSPEND (using pm_runtime)
- ODR (Output Data Rate) selection
- Scale and samp_freq selection
- IIO triggered buffer, IIO reg access
- NEW_DATA interrupt + trigger
Below features to be done:
- Motion Events: ACTIVE, TAP, ORIENT, FREEFALL
- Low Power mode
Datasheet: https://cdn-shop.adafruit.com/product-files/5309/MSA311-V1.1-ENG.pdf
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220822175011.2886-4-ddrokosov@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Hi Linus,
Please pull (hopefully) the last portion of fixes from Sander for his
UP rework series. The original series came from -mm tree, and it was
not the latest version, that's why we need follow-ups. It fixes only
a test introduced by that series. The test fails under certain configs.
From Sander:
This series fixes the reported issues, and implements the suggested
improvements, for the version of the cpumask tests [1] that was merged
with commit c41e8866c2 ("lib/test: introduce cpumask KUnit test
suite").
These changes include fixes for the tests, and better alignment with the
KUnit style guidelines.
Thanks,
Yury
-----BEGIN PGP SIGNATURE-----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=oNmV
-----END PGP SIGNATURE-----
Merge tag 'bitmap-6.0-rc3' of github.com:/norov/linux
Pull bitmap fixes from Yury Norov:
"Fix the reported issues, and implements the suggested improvements,
for the version of the cpumask tests [1] that was merged with commit
c41e8866c2 ("lib/test: introduce cpumask KUnit test suite").
These changes include fixes for the tests, and better alignment with
the KUnit style guidelines"
* tag 'bitmap-6.0-rc3' of github.com:/norov/linux:
lib/cpumask_kunit: add tests file to MAINTAINERS
lib/cpumask_kunit: log mask contents
lib/test_cpumask: follow KUnit style guidelines
lib/test_cpumask: fix cpu_possible_mask last test
lib/test_cpumask: drop cpu_possible_mask full test
-----BEGIN PGP SIGNATURE-----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=mGLL
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.0-2022-08-26' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Add missing header file to the MAINTAINERS entry for io_uring (Ammar)
- liburing and the kernel ship the same io_uring.h header, but one
change we've had for a long time only in liburing is to ensure it's
C++ safe. Add extern C around it, so we can more easily sync them in
the future (Ammar)
- Fix an off-by-one in the sync cancel added in this merge window (me)
- Error handling fix for passthrough (Kanchan)
- Fix for address saving for async execution for the zc tx support
(Pavel)
- Fix ordering for TCP zc notifications, so we always have them ordered
correctly between "data was sent" and "data was acked". This isn't
strictly needed with the notification slots, but we've been pondering
disabling the slot support for 6.0 - and if we do, then we do require
the ordering to be sane. Regardless of that, it's the sane thing to
do in terms of API (Pavel)
- Minor cleanup for indentation and lockdep annotation (Pavel)
* tag 'io_uring-6.0-2022-08-26' of git://git.kernel.dk/linux-block:
io_uring/net: save address for sendzc async execution
io_uring: conditional ->async_data allocation
io_uring/notif: order notif vs send CQEs
io_uring/net: fix indentation
io_uring/net: fix zc send link failing
io_uring/net: fix must_hold annotation
io_uring: fix submission-failure handling for uring-cmd
io_uring: fix off-by-one in sync cancelation file check
io_uring: uapi: Add `extern "C"` in io_uring.h for liburing
MAINTAINERS: Add `include/linux/io_uring_types.h`
Current release - new code bugs:
- dsa: don't dereference NULL extack in dsa_slave_changeupper()
- dpaa: fix <1G ethernet on LS1046ARDB
- neigh: don't call kfree_skb() under spin_lock_irqsave()
Previous releases - regressions:
- r8152: fix the RX FIFO settings when suspending
- dsa: microchip: keep compatibility with device tree blobs with
no phy-mode
- Revert "net: macsec: update SCI upon MAC address change."
- Revert "xfrm: update SA curlft.use_time", comply with RFC 2367
Previous releases - always broken:
- netfilter: conntrack: work around exceeded TCP receive window
- ipsec: fix a null pointer dereference of dst->dev on a metadata
dst in xfrm_lookup_with_ifid
- moxa: get rid of asymmetry in DMA mapping/unmapping
- dsa: microchip: make learning configurable and keep it off
while standalone
- ice: xsk: prohibit usage of non-balanced queue id
- rxrpc: fix locking in rxrpc's sendmsg
Misc:
- another chunk of sysctl data race silencing
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=azH5
-----END PGP SIGNATURE-----
Merge tag 'net-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from ipsec and netfilter (with one broken Fixes tag).
Current release - new code bugs:
- dsa: don't dereference NULL extack in dsa_slave_changeupper()
- dpaa: fix <1G ethernet on LS1046ARDB
- neigh: don't call kfree_skb() under spin_lock_irqsave()
Previous releases - regressions:
- r8152: fix the RX FIFO settings when suspending
- dsa: microchip: keep compatibility with device tree blobs with no
phy-mode
- Revert "net: macsec: update SCI upon MAC address change."
- Revert "xfrm: update SA curlft.use_time", comply with RFC 2367
Previous releases - always broken:
- netfilter: conntrack: work around exceeded TCP receive window
- ipsec: fix a null pointer dereference of dst->dev on a metadata dst
in xfrm_lookup_with_ifid
- moxa: get rid of asymmetry in DMA mapping/unmapping
- dsa: microchip: make learning configurable and keep it off while
standalone
- ice: xsk: prohibit usage of non-balanced queue id
- rxrpc: fix locking in rxrpc's sendmsg
Misc:
- another chunk of sysctl data race silencing"
* tag 'net-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
net: lantiq_xrx200: restore buffer if memory allocation failed
net: lantiq_xrx200: fix lock under memory pressure
net: lantiq_xrx200: confirm skb is allocated before using
net: stmmac: work around sporadic tx issue on link-up
ionic: VF initial random MAC address if no assigned mac
ionic: fix up issues with handling EAGAIN on FW cmds
ionic: clear broken state on generation change
rxrpc: Fix locking in rxrpc's sendmsg
net: ethernet: mtk_eth_soc: fix hw hash reporting for MTK_NETSYS_V2
MAINTAINERS: rectify file entry in BONDING DRIVER
i40e: Fix incorrect address type for IPv6 flow rules
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
net: Fix a data-race around sysctl_somaxconn.
net: Fix a data-race around netdev_unregister_timeout_secs.
net: Fix a data-race around gro_normal_batch.
net: Fix data-races around sysctl_devconf_inherit_init_net.
net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
net: Fix a data-race around netdev_budget_usecs.
net: Fix data-races around sysctl_max_skb_frags.
net: Fix a data-race around netdev_budget.
...
Commit c078290a2b ("selftests: include bonding tests into the kselftest
infra") adds the bonding tests in the directory:
tools/testing/selftests/drivers/net/bonding/
The file entry in MAINTAINERS for the BONDING DRIVER however refers to:
tools/testing/selftests/net/bonding/
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken file pattern.
Repair this file entry in BONDING DRIVER.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220824072945.28606-1-lukas.bulwahn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cpumask related files are listed under the BITMAP API section, so the
file with tests for cpumask should be added to that list.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
File include/linux/io_uring_types.h doesn't have a maintainer, add it
to the io_uring section.
Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Maintainers of the directory Documentation/devicetree/bindings/input
are also the maintainers of the corresponding directory
include/dt-bindings/input.
Add the file entry for include/dt-bindings/input to the appropriate
section in MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220613115654.28117-1-lukas.bulwahn@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This creates a test collection in drivers/net/bonding for bonding
specific kernel selftests.
The first test is a reproducer that provisions a bond and given the
specific order in how the ip-link(8) commands are issued the bond never
transmits an LACPDU frame on any of its slaves.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCYwNkcwAKCRCRxhvAZXjc
ohHlAQC0Sb0jZxLDHeKXr6lHR+a+jOYTisM/8GkCygBhYBqlFgD+KclaIVJp9v/1
O88/iv91XfomkDSxNknv+MxoWE2i7Ao=
=hvvJ
-----END PGP SIGNATURE-----
Merge tag 'fs.idmapped.fixes.v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping
Pull idmapping fixes from Christian Brauner:
- Since Seth joined as co-maintainer for idmapped mounts we decided to
use a shared git tree. Konstantin suggested we use vfs/idmapping.git
on kernel.org under the vfs/ namespace. So this updates the tree in
the maintainers file.
- Ensure that POSIX ACLs checking, getting, and setting works correctly
for filesystems mountable with a filesystem idmapping that want to
support idmapped mounts.
Since no filesystems mountable with an fs_idmapping do yet support
idmapped mounts there is no problem. But this could change in the
future, so add a check to refuse to create idmapped mounts when the
mounter is not privileged over the mount's idmapping.
- Check that caller is privileged over the idmapping that will be
attached to a mount.
Currently no FS_USERNS_MOUNT filesystems support idmapped mounts,
thus this is not a problem as only CAP_SYS_ADMIN in init_user_ns is
allowed to set up idmapped mounts. But this could change in the
future, so add a check to refuse to create idmapped mounts when the
mounter is not privileged over the mount's idmapping.
- Fix POSIX ACLs for ntfs3. While looking at our current POSIX ACL
handling in the context of some overlayfs work I went through a range
of other filesystems checking how they handle them currently and
encountered a few bugs in ntfs3.
I've sent this some time ago and the fixes haven't been picked up
even though the pull request for other ntfs3 fixes got sent after.
This should really be fixed as right now POSIX ACLs are broken in
certain circumstances for ntfs3.
* tag 'fs.idmapped.fixes.v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping:
ntfs: fix acl handling
fs: require CAP_SYS_ADMIN in target namespace for idmapped mounts
MAINTAINERS: update idmapping tree
acl: handle idmapped mounts for idmapped filesystems
-----BEGIN PGP SIGNATURE-----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=dod2
-----END PGP SIGNATURE-----
Merge tag '6.0-rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
- memory leak fix
- two small cleanups
- trivial strlcpy removal
- update missing entry for cifs headers in MAINTAINERS file
* tag '6.0-rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: move from strlcpy with unused retval to strscpy
cifs: Fix memory leak on the deferred close
cifs: remove useless parameter 'is_fsctl' from SMB2_ioctl()
cifs: remove unused server parameter from calc_smb_size()
cifs: missing directory in MAINTAINERS file
Commit ba96b2e797 ("dt-bindings: gpio: gpio-xilinx: Convert Xilinx axi
gpio binding to YAML") converts gpio-xilinx.txt to xlnx,gpio-xilinx.yaml,
but missed to adjust its reference in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.
Repair this file reference in XILINX GPIO DRIVER.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Since Seth joined as a maintainer in ba40a57ff0 ("Add Seth Forshee as
co-maintainer for idmapped mounts") it was best to get a shared git tree
instead of using our personal repositories. So we requested and
Konstantin suggested and gave us a new "idmapping" repository under the
pre-existing but mainly unused vfs namespace. Just makes it easier for
Seth to send fixes in case I'm out or someone else ever takes over.
Cc: Seth Forshee <sforshee@digitalocean.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Link: https://lore.kernel.org/r/20220816113514.43304-2-brauner@kernel.org
A few fixes that came in since my pull request, the Meson fix is a
little large since it's fixing all possible cases of the problem that
was observed with the driver and clock API trying to share configuration
by integrating the device clocking fully with the clock API rather than
spot fixing the one instance that was observed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmL7fVUACgkQJNaLcl1U
h9DNIAf/ThNZXWK1+ujLkCe3VW2CfOWSBQMtL1jW7vrRI2qNMoEj478wUMUZJ83R
Sl5X7w3PW7OmiJTvTzqngS+OkUUR/8Hcp8Cvcz1DJYmBV0iYOwPjinNfbB/Z77B7
4HaBOdBdMSCq6nFX7obKc4tyNGb6ZBD3YJ+PW+CRhUozfvGPXAUDoh5Eq4q1efh3
UJW5lP88Lp4zwd9rh8y05ugLFzXdxWV1LwICj2cj3+KceRwObwNfSs8Qp60iOrC+
QuSIiaZJA77BbG6y/i6Y/lZo/06ZcYAU0QzdUdaffNk+V7aadfvz2IlTHuoe186A
bV3xv1ucL2FJlrx4DAZtWp4b5EcPmA==
=xXEL
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few fixes that came in since my pull request, the Meson fix is a
little large since it's fixing all possible cases of the problem that
was observed with the driver and clock API trying to share
configuration by integrating the device clocking fully with the clock
API rather than spot fixing the one instance that was observed"
* tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dt-bindings: Drop Pratyush Yadav
spi: meson-spicc: add local pow2 clock ops to preserve rate between messages
MAINTAINERS: rectify entry for ARM/HPE GXP ARCHITECTURE
spi: spi.c: Add missing __percpu annotations in users of spi_statistics
The actual status of the code is Maintained.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Cc: Kent Gustavsson <kent@minoris.se>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio <linux-iio@vger.kernel.org>
Link: https://lore.kernel.org/r/20220723092030.260812-1-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The include/uapi/linux/cifs directory (not just fs/cifs and
fs/smbfs_common) should be included in cifs entry in the
MAINTAINERS file.
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYvi0yQAKCRCAXGG7T9hj
vmikAQDWSrcWuxDkGnzut0A1tBQRUCWDMyKPqigWAA5tH2sPgAEAtWfBvT1xyl7T
gZ22I7o21WxxDGyvNUcA65pK7c2cpg8=
=UMbq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- fix the handling of the "persistent grants" feature negotiation
between Xen blkfront and Xen blkback drivers
- a cleanup of xen.config and adding xen.config to Xen section in
MAINTAINERS
- support HVMOP_set_evtchn_upcall_vector, which is more compliant to
"normal" interrupt handling than the global callback used up to now
- further small cleanups
* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
xen: remove XEN_SCRUB_PAGES in xen.config
xen/pciback: Fix comment typo
xen/xenbus: fix return type in xenbus_file_read()
xen-blkfront: Apply 'feature_persistent' parameter when connect
xen-blkback: Apply 'feature_persistent' parameter when connect
xen-blkback: fix persistent grants negotiation
x86/xen: Add support for HVMOP_set_evtchn_upcall_vector
and NTB EndPoint Function (EPF) support and the various fixes from that
being in -next for Linux v5.20
-----BEGIN PGP SIGNATURE-----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=DAah
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.20' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Non-Transparent Bridge updates.
Fix of heap data and clang warnings, support for a new Intel NTB
device, and NTB EndPoint Function (EPF) support and the various fixes
for that"
* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
NTB: EPF: Tidy up some bounds checks
NTB: EPF: Fix error code in epf_ntb_bind()
PCI: endpoint: pci-epf-vntb: reduce several globals to statics
PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
PCI: endpoint: Fix Kconfig dependency
NTB: EPF: set pointer addr to null using NULL rather than 0
Documentation: PCI: extend subheading underline for "lspci output" section
Documentation: PCI: Use code-block block for scratchpad registers diagram
Documentation: PCI: Add specification for the PCI vNTB function device
PCI: endpoint: Support NTB transfer between RC and EP
NTB: epf: Allow more flexibility in the memory BAR map method
PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
ntb: intel: add GNR support for Intel PCIe gen5 NTB
NTB: ntb_tool: uninitialized heap data in tool_fn_write()
ntb: idt: fix clang -Wformat warnings
The PCI Endpoint NTB drivers are under the NTB umbrella. Add an entry
there to allow for notification of changes for it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
