The root Flow Table for each Flow Table Type is defined,
by default, as the Flow Table with level 0.
In order not to use an empty flow tables and introduce new hops,
but still preserve space for flow-tables that have a priority
greater(lower number) than the current flow table, we introduce this
new set root flow table command.
This command tells the HW to start matching packets from the
assigned root flow table.
This command is used when we create new flow table with level lower than the
current lowest flow table or it is the first flow table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A preparation step which adds support for reading the hardware
internal timer and the hardware timestamping from the CQE.
In addition, advertize device_frequency_khz HCA capability.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new Flow Steering (FS) firmware commands,
in-order to support the new flow steering infrastructure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch vport context is unlike NIC vport context, managed by the
E-Switch manager or vport_group_manager and not by the NIC(VF) driver.
The E-Switch manager can access (read/modify) any of its vports
E-Switch context.
Currently E-Switch vport context includes only clietnt and server
vlan insertion and striping data (for later support of VST mode).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling E-Switch SRIOV for nvfs+1 vports.
Create E-Switch FDB for L2 UC/MC mac steering between VFs/PF and
external vport (Uplink).
FDB contains forwarding rules such as:
UC MAC0 -> vport0(PF).
UC MAC1 -> vport1.
UC MAC2 -> vport2.
MC MACX -> vport0, vport2, Uplink.
MC MACY -> vport1, Uplink.
For unmatched traffic FDB has the following default rules:
Unmached Traffic (src vport != Uplink) -> Uplink.
Unmached Traffic (src vport == Uplink) -> vport0(PF).
FDB rules population:
Each NIC vport (VF) will notify E-Switch manager of its UC/MC vport
context changes via modify vport context command, which will be
translated to an event that will be handled by E-Switch manager (PF)
which will update FDB table accordingly.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define needed hardware structures and capabilities needed
for E-Switch FDB flow tables and read them on driver load.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) vlan table changes.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) promisc mode changes.
Preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for SR-IOV we add here an API to enable each e-switch
manager (PF) to configure its VFs link states in e-switch
preparation for ethernet sriov.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update HCA capabilities and HW struct to include needed
capabilities for upcoming Ethernet Switch (SR-IOV E-Switch).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds SRIOV base support for mlx5 supported devices. The same
driver is used for both PFs and VFs; VFs are identified by the driver
through the flag MLX5_PCI_DEV_IS_VF added to the pci table entries.
Virtual functions are created as usual through writing a value to the
sriov_numvs sysfs file of the PF device. Upon instantiating VFs, they will
all be probed by the driver on the hypervisor. One can gracefully unbind
them through /sys/bus/pci/drivers/mlx5_core/unbind.
mlx5_wait_for_vf_pages() was added to ensure that when a VF dies without
executing proper teardown, the hypervisor driver waits till all of the
pages that were allocated at the hypervisor to maintain its operation
are returned.
In order for the VF to be operational, the PF needs to call enable_hca
for it. This can be done before the VFs are created through a call to
pci_enable_sriov.
If the there are VFs assigned to a VMs when the driver of the PF is
unloaded, all the VF will experience system error and PF driver unloads
cleanly; in this case pci_disable_sriov is not called and the devices
will show when running lspci. Once the PF driver is reloaded, it will
sync its data structures which maintain state on its VFs.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent outgoing multicast frames from looping back to the RX queue.
By introducing new HW capability self_lb_en_modifiable, which indicates
the support to modify self_lb_en bit in modify_tir command.
When this capability is set we can prevent TIRs from sending back
loopback multicast traffic to their own RQs, by "refreshing TIRs" with
modify_tir command, on every time new channels (SQs/RQs) are created at
device open.
This is needed since TIRs are static and only allocated once on driver
load, and the loopback decision is under their responsibility.
Fixes issues of the kind:
"IPv6: eth2: IPv6 duplicate address fe80::e61d:2dff:fe5c:f2e9 detected!"
The issue is seen since the IPv6 solicitations multicast messages are
loopedback and the network stack thinks they are coming from another host.
Fixes: 5c50368f38 ("net/mlx5e: Light-weight netdev open/stop")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX-4 HW implements inverted XOR8.
To make it act as XOR we re-order the HW RSS indirection table.
Set XOR to be the default RSS hash function and add ethtool API to
control it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_ifc.h was heavily modified here since it is now generated by a
script from the device specification (PRM rev 0.25). This specification
is backward compatible to existing hardware.
Some structures/fields were added here in order to enable the Ethernet
functionality of the driver.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transform device capabilities related commands to use set/get macros to
manipulate command mailboxes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an auto generated header file that describes hardware registers along with
set of macros that set/get values. The macros do static checks to avoid
overflow, handle endianess, and overall provide a clean way to code commands.
Currently the header file is small and we will add structs as we make use of
the macros.
A few commands were removed from the commands enum since they are not supported
currently and will be added when support is available.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
