The calibration data for devices w/o a separate
EEPROM chip can be specified via the 'eeprom_data'
field of 'ath9k_platform_data'. The 'eeprom_data'
is usually filled from board specific setup
functions. It is easy if the EEPROM data is mapped
to the memory, but it can be complicated if it is
stored elsewhere.
The patch adds support for loading of the EEPROM
data via the firmware API to avoid this limitation.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_nvram_read' function takes a
'struct ath_common *' as its first argument.
Almost each of its caller has a 'struct ath_hw *'
parameter in their argument list, and that is
dereferenced in order to get the 'struct ath_common'
pointer.
Change the first argument of 'ath9k_hw_nvram_read'
to be a 'struct ath_hw *', and remove the dereference
calls from the callers.
Also change the type of the first argument of the
ar9300_eeprom_read_{byte,word} functions.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show the EEPROM offset of the failed read operation
in 'ath9k_hw_nvram_read'. The debug message is more
informative this way.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fill_eeprom functions are printing the same
debug message in case the 'ath9k_hw_nvram_read'
function fails. Remove the duplicated code from
fill_eeprom functions and add the ath_dbg call
directly into 'ath9k_hw_nvram_read'.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor
for a chip measured in clean air, it refers to the lowest expected reading.
Depending on the frequency, this measurement can vary by about 6db, thus
causing a higher reported channel noise and signal strength.
Factor in the 6db offset when converting internal noisefloor to channel noise.
This patch makes the reported values more accurate for all chips without
affecting NF calibration behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign the training power for PAPRD based on the chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a HW capability to indicate whether PAPRD is enabled
for the card, since PAPRD could be enabled in the EEPROM, but
disabled in the driver. This makes things clearer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retraining of PAPRD based on agc2_pwr is required for
chips other than AR9485.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Remove unneeded memset.
All the values in the PAPRD gain table are filled, so there
is no need to zero out the arrays.
* Use GFP_KERNEL in ar9003_paprd_create_curve
This is called from the PAPRD work, so the atomic variant
is not needed.
* Change return type of ar9003_paprd_setup_gain_table
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the PowerSave wrappers outside ath_paprd_activate(),
since they are already being used in ath_paprd_calibrate().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PAPRD training control registers have to be
programmed with values that depend on the chip. This patch
ensures that the correct values are chosen for the chip
in use.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various PAPRD registers are at addresses that are different
from those for the rest of the chips in the AR9003 family.
Fix them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
D-Link DWA-125/B1 is a relatively new USB Wi-Fi adapter, using a
Ralink chipset supported by the rt2800usb driver. Currently, to work
around the problem (it's missing in all present kernel versions,
up to and including 3.7.x), I had to add this to /etc/rc.local:
echo 2001 3c1e >> /sys/bus/usb/drivers/rt2800usb/new_id
After that, the device works without problems. Been using it for over
a week with no bugs in sight.
The attached patch is trivial and simply adds the new USB ID to the
list of devices handled by rt2800usb.
Signed-off-by: Maia Kozheva <sikon@ubuntu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression which was introduced by:
"carl9170: split up carl9170_handle_mpdu"
Previously, the ieee80211_rx_status was kept on the
stack of carl9170_handle_mpdu. Now it's passed into
the function as a pointer parameter. Hence, the old
memcpy call needs to be fixed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This device can be found on some embedded devices connected to a
Broadcom SoC like the BCM4718.
I tested this with my Netgear WNDR3400 v1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described in the documentation of bcma_wflush16 in drivers/net
/wireless/brcm80211/brcmsmac/types.h some PCIe controllers of Broadcom
SoCs are broken. The PCIe controller on these SoCs are mostly used to
connect some additional wifi device to the SoC and some of these wifi
devices are supported by brcmsmac.
For my BCM43224 connected to the broken PCIe controller of the BCM4718 I
need an extra read after write in brcms_b_write_objmem() to prevent a
Data bus error. This fixes the problem reading tsf_random later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k: Fix the 'xmit' debugfs file" changed the
the array size of ath_stats.txstats to IEEE80211_NUM_ACS,
which is wrong because the HW queue number is used to
update the statistics. Revert back to using ATH9K_NUM_TX_QUEUES.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent versions of udev cause synchronous firmware loading from the
probe routine to fail because the request to user space times out.
The original fix for b43legacy (commit a3ea2c7) moved the firmware
load from the probe routine to a work queue, but it still used synchronous
firmware loading. This method is OK when b43legacy is built as a module;
however, it fails when the driver is compiled into the kernel.
This version changes the code to load the initial firmware file
using request_firmware_nowait(). A completion event is used to
hold the work queue until that file is available. The remaining
firmware files are read synchronously.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> (V3.4+)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for bcma wifi core revision 17 which is found on
BCM4716/4717/4718 SoCs. The firmware version 610.812 for brcmsmac found
in linux-firmware does not support these cores, but a firmware
generated with b43-fwcutter from the proprietary broadcom wireless
driver works with these chips. This wifi core contains a revision 5
N-PHY and a revision 7 radio of type 0x2056.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit f74b9d365ddd33a375802b064f96a5d0e99af7c0.
Turns out reverting commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd
"ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to
bring the tx power back to normal levels on devices like the
Buffalo WZR-HP-G450H, this one needs to be reverted as well.
This revert improves tx power by ~10 db on that device
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of WL_CONN(...) macro in favor of brcmf_dbg(CONN,...)
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of WL_SCAN(...) macro in favor of brcmf_dbg(SCAN,...)
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of WL_TRACE(...) macro in favor of brcmf_dbg(TRACE,...)
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of WL_INFO() in favor of brcmf_dbg(INFO,...).
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The source file wl_cfg80211.c has its own debug macros and levels.
This patch maps the macros to the ones used in the rest of the
brcmfmac driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.
This patch replaces the usage of these string functions in the 8390
accessors with io{read,write}{8,16,32}_rep calls instead.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.
This patch replaces the usage of these string functions in the default
DM9000 accessors with io{read,write}{8,16,32}_rep calls instead. This
is required as the dm9000 driver is in use by the blackfin
architecture which uses the asm-generic io accessors.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The {read,write}s{b,w,l} operations are not defined by all architectures
and are being removed from the asm-generic/io.h interface.
This patch replaces the usage of these string functions in the default
SMC accessors with io{read,write}{8,16,32}_rep calls instead, which are
defined for all architectures.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to brcmf_dbg(ERROR, ...) only resulted in a log message
when compiled with -DDEBUG. Error messages are valuable for resolving
issues so this patch replaces it with brcmf_err(...) so they always
end up in the log.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, adding a new event requires modification in two source
files. Use macro definition to have one place and have better
maintainability.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using gcc v4.7.2 gave following warning:
CC [M] drivers/net/wireless/brcm80211/brcmsmac/aiutils.o
brcmsmac/aiutils.c: In function 'ai_deviceremoved':
brcmsmac/aiutils.c:733:9: error: 'w' may be used uninitialized
in this function [-Werror=uninitialized]
Inspection of the pci_read_config_dword() function showed it can
return without modifying the output variable 'w' so this patch
initializes it to 0.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework the bus interface between common driver part and bus-specific
driver part. It prepares for adding tracing in bus-specific callback
functions.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a missing endian conversion which results in the
interface failing to come up on BE platforms.
It also removes an unnecessary pointer dereference from this
function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the ethtool register dump for smsc95xx to dump
all 4 bytes of the final register (COE_CR) instead of just the
first byte.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes when we decide what the device's MAC address
is from per ifconfig up to once when the device is connected.
Without this patch, a manually forced device MAC is overwritten
on ifconfig down/up. Also devices that have no EEPROM are
assigned a new random address on ifconfig down/up instead of
persisting the same one.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Reported-by: Robert Cunningham <rcunningham@nsmsurveillance.com>
Cc: Bjorn Mork <bjorn@mork.no>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Obviously it should check !vi->rq.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the ethtool_{set|get}_channels method of virtio-net to
allow user to change the number of queues when the device is running on demand.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the multiqueue (VIRTIO_NET_F_MQ) support to virtio_net
driver. VIRTIO_NET_F_MQ capable device could allow the driver to do packet
transmission and reception through multiple queue pairs and does the packet
steering to get better performance. By default, one one queue pair is used, user
could change the number of queue pairs by ethtool in the next patch.
When multiple queue pairs is used and the number of queue pairs is equal to the
number of vcpus. Driver does the following optimizations to implement per-cpu
virt queue pairs:
- select the txq based on the smp processor id.
- smp affinity hint to the cpu that owns the queue pairs.
This could be used with the flow steering support of the device to guarantee the
packets of a single flow is handled by the same cpu.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support multiqueue transmitq/receiveq, the first step is to separate queue
related structure from virtnet_info. This patch introduce send_queue and
receive_queue structure and use the pointer to them as the parameter in
functions handling sending/receiving.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds capability in vxlan to identify received
checksummed inner packets and signal them to the upper layers of
the stack. The driver needs to set the skb->encapsulation bit
and also set the skb->ip_summed to CHECKSUM_UNNECESSARY.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow VXLAN to make use of Tx checksum offloading and Tx scatter-gather.
The advantage to these two changes is that it also allows the VXLAN to
make use of GSO.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GigaMAC registers have been reported left unitialized in several
situations:
- after cold boot from power-off state
- after S3 resume
Tweaking rtl_hw_phy_config takes care of both.
This patch removes an excess entry (",") at the end of the exgmac_reg
array as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2c60db037034 ('net: provide a default dev->ethtool_ops')
all devices have a non-null ethtool_ops. Test only
dev->ethtool_ops->get_link in both places where we care.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct a mistake made in the previous commit due to reckless
copy-and-pasting.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the standard #defines for PCIe Capability ASPM fields.
Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits. PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
