[ Upstream commit 89382022b370dfd34eaae9c863baa123fcd4d132 ]
Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.
Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.
Move the place where reset_control_deassert() is called so that the
recommended order of reset release/clock enable steps is kept.
A64 manual states that:
3.3.6.4. Gating and reset
Make sure that the reset signal has been released before the release of
module clock gating;
This fixes the issue and removes some LoC at the same time.
Fixes: dccc5c3b6f ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/a8ae84bd2dc4b55fe428f8e20f31438bf8bb6762.1684089931.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 86edac7d3888c715fe3a81bd61f3617ecfe2e1dd upstream.
This reverts commit f05c7b7d9ea9477fcc388476c6f4ade8c66d2d26.
That change was causing a regression in the generic-adc-thermal-probed
bootrr test as reported in the kernelci-results list [1].
A proper rework will take longer, so revert it for now.
[1] https://groups.io/g/kernelci-results/message/42660
Fixes: f05c7b7d9ea9 ("thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe")
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230525121811.3360268-1-ricardo.canuelo@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f05c7b7d9ea9477fcc388476c6f4ade8c66d2d26 ]
Smatch reports:
1. mtk_thermal_probe() warn: 'apmixed_base' from of_iomap() not released.
2. mtk_thermal_probe() warn: 'auxadc_base' from of_iomap() not released.
The original code forgets to release iomap resource when handling errors,
fix it by switch to devm_of_iomap.
Fixes: 89945047b1 ("thermal: mediatek: Add tsensor support for V2 thermal system")
Signed-off-by: Kang Chen <void0red@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230419020749.621257-1-void0red@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1467fb960349dfa5e300658f1a409dde2cfb0c51 ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: b474303ffd ("thermal: add Intel BXT WhiskeyCove PMIC thermal driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1b930e740811d416de4d2074da48b6633a672c8 ]
If alloc_soc_dts() fails, then we can just return. Trying to free
"soc_dts" will lead to an Oops.
Fixes: 8c18769396 ("thermal: intel Quark SoC X1000 DTS thermal driver")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e47363588377e1bdb65e2b020b409cfb44dd260 upstream.
The powerclamp cooling device cur_state shows actual idle observed by
package C-state idle counters. But the implementation is not sufficient
for multi package or multi die system. The cur_state value is incorrect.
On these systems, these counters must be read from each package/die and
somehow aggregate them. But there is no good method for aggregation.
It was not a problem when explicit CPU model addition was required to
enable intel powerclamp. In this way certain CPU models could have
been avoided. But with the removal of CPU model check with the
availability of Package C-state counters, the driver is loaded on most
of the recent systems.
For multi package/die systems, just show the actual target idle state,
the system is trying to achieve. In powerclamp this is the user set
state minus one.
Also there is no use of starting a worker thread for polling package
C-state counters and applying any compensation for multiple package
or multiple die systems.
Fixes: b721ca0d19 ("thermal/powerclamp: remove cpu whitelist")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40dc1929089fc844ea06d9f8bdb6211ed4517c2e ]
Add the PCI ID for the Wellsburg C610 series chipset PCH.
The driver can read the temperature from the Wellsburg PCH with only
the PCI ID added and no other modifications.
Signed-off-by: Tim Zimmermann <tim@linux4.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7fcfe67f9f410736b758969477b17ea285e8e6c ]
The return value from the call to intel_tcc_get_tjmax() is int, which can
be a negative error code. However, the return value is being assigned to
an u32 variable 'tj_max', so making 'tj_max' an int.
Eliminate the following warning:
./drivers/thermal/intel/intel_soc_dts_iosf.c:394:5-11: WARNING: Unsigned expression compared with zero: tj_max < 0
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3637
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15cc25829a97c3957e520e971868aacc84341317 ]
The commit 74c8e6bffbe1 ("driver core: Add __alloc_size hint to devm
allocators") exposes a panic "BRK handler: Fatal exception" on the
hi3660_thermal_probe funciton.
This is because the function allocates memory for only one
sensors array entry, but tries to fill up a second one.
Fix this by removing the unneeded second access.
Fixes: 7d3a2a2bba ("thermal/drivers/hisi: Fix number of sensors on hi3660")
Signed-off-by: Yongqin Liu <yongqin.liu@linaro.org>
Link: https://lore.kernel.org/linux-mm/20221101223321.1326815-5-keescook@chromium.org/
Link: https://lore.kernel.org/r/20230210141507.71014-1-yongqin.liu@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b26b7c9cdefdcb478047c30901d2379ef9e50fc ]
The minimal resource ID is 0: IMX_SC_R_AP_0=0, so fix
the loop condition. Aside of this - constify the array.
Fixes: 31fd4b9db1 ("thermal/drivers/imx_sc: Rely on the platform data to get the resource id")
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Dong Aisheng <Aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20230117091956.61729-1-viorel.suman@oss.nxp.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5011a110295d25418f5918a6af7bfcdb00dd4e34 ]
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221212220217.3777176-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
Stable-dep-of: 4b26b7c9cdef ("thermal/drivers/imx_sc_thermal: Fix the loop condition")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 903238a33c116edf5f64f7a3fd246e6169cccfa6 ]
On msm8939 last (hwid=10) sensor was added in the hw revision 3.0.
Calibration data for it was placed outside of the main calibration data
blob, so it is not accessible by the current blob-parsing code.
Moreover data for the sensor's p2 is not contiguous in the fuses. This
makes it hard to use nvmem_cell API to parse calibration data in a
generic way.
Since the sensor doesn't seem to be actually used by the existing
hardware, disable the sensor for now.
Fixes: 332bc8ebab ("thermal: qcom: tsens-v0_1: Add support for MSM8939")
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230101194034.831222-9-dmitry.baryshkov@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7d3006be5ca7b04e4b84b5ceaae55a700e511bd ]
Tsens driver mentions that msm8976 data should be used for both msm8976
and msm8956 SoCs. This is not quite correct, as according to the
vendor kernels, msm8976 should use standard slope values (3200), while
msm8956 really uses the slope values found in the driver.
Add separate compatibility string for msm8956, move slope value
overrides to the corresponding init function and use the standard
compute_intercept_slope() function for both platforms.
Fixes: 0e58029017 ("thermal: qcom: tsens-v1: Add support for MSM8956 and MSM8976")
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230101194034.831222-7-dmitry.baryshkov@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acd7e9ee57c880b99671dd99680cb707b7b5b0ee ]
In order to prevent int340x_thermal_get_trip_type() from possibly
racing with int340x_thermal_read_trips() invoked by int3403_notify()
add locking to it in analogy with int340x_thermal_get_trip_temp().
Fixes: 6757a7abe47b ("thermal: intel: int340x: Protect trip temperature from concurrent updates")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6757a7abe47bcb12cb2d45661067e182424b0ee3 upstream.
Trip temperatures are read using ACPI methods and stored in the memory
during zone initializtion and when the firmware sends a notification for
change. This trip temperature is returned when the thermal core calls via
callback get_trip_temp().
But it is possible that while updating the memory copy of the trips when
the firmware sends a notification for change, thermal core is reading the
trip temperature via the callback get_trip_temp(). This may return invalid
trip temperature.
To address this add a mutex to protect the invalid temperature reads in
the callback get_trip_temp() and int340x_thermal_read_trips().
Fixes: 5fbf7f27fa ("Thermal/int340x: Add common thermal zone handler")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.0+ <stable@vger.kernel.org> # 5.0+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c54b7bc8a31ce0f7cc7f8deef05067df414f1d8 ]
put_device() shouldn't be called before a prior call to
device_register(). __thermal_cooling_device_register() doesn't follow
that properly and needs fixing. Also
thermal_cooling_device_destroy_sysfs() is getting called unnecessarily
on few error paths.
Fix all this by placing the calls at the right place.
Based on initial work done by Caleb Connolly.
Fixes: 4748f9687caa ("thermal: core: fix some possible name leaks in error paths")
Fixes: c408b3d1d9bb ("thermal: Validate new state in cur_state_store()")
Reported-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Frank Rowand <frowand.list@gmail.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e49a1e1ee078aee21006192076a8d93335e0daa9 ]
Return an error pointer if ->get_max_state() fails. The current code
returns NULL which will cause an oops in the callers.
Fixes: c408b3d1d9bb ("thermal: Validate new state in cur_state_store()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 6c54b7bc8a31 ("thermal: core: call put_device() only after device_register() fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c408b3d1d9bbc7de5fb0304fea424ef2539da616 ]
In cur_state_store(), the new state of the cooling device is received
from user-space and is not validated by the thermal core but the same is
left for the individual drivers to take care of. Apart from duplicating
the code it leaves possibility for introducing bugs where a driver may
not do it right.
Lets make the thermal core check the new state itself and store the max
value in the cooling device structure.
Link: https://lore.kernel.org/all/Y0ltRJRjO7AkawvE@kili/
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 6c54b7bc8a31 ("thermal: core: call put_device() only after device_register() fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c6b30060777352e7881383bab726046d8c3c610 ]
Calls to thermal_zone_get_temp() are not protected against thermal zone
device removal. As result, it is possible that the thermal zone operations
callbacks are no longer valid when thermal_zone_get_temp() is called.
This may result in crashes such as
BUG: unable to handle page fault for address: ffffffffc04ef420
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 5d60e067 P4D 5d60e067 PUD 5d610067 PMD 110197067 PTE 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 3209 Comm: cat Tainted: G W 5.10.136-19389-g615abc6eb807 #1 02df41ac0b12f3a64f4b34245188d8875bb3bce1
Hardware name: Google Coral/Coral, BIOS Google_Coral.10068.92.0 11/27/2018
RIP: 0010:thermal_zone_get_temp+0x26/0x73
Code: 89 c3 eb d3 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 53 48 85 ff 74 50 48 89 fb 48 81 ff 00 f0 ff ff 77 44 48 8b 83 98 03 00 00 <48> 83 78 10 00 74 36 49 89 f6 4c 8d bb d8 03 00 00 4c 89 ff e8 9f
RSP: 0018:ffffb3758138fd38 EFLAGS: 00010287
RAX: ffffffffc04ef410 RBX: ffff98f14d7fb000 RCX: 0000000000000000
RDX: ffff98f17cf90000 RSI: ffffb3758138fd64 RDI: ffff98f14d7fb000
RBP: ffffb3758138fd50 R08: 0000000000001000 R09: ffff98f17cf90000
R10: 0000000000000000 R11: ffffffff8dacad28 R12: 0000000000001000
R13: ffff98f1793a7d80 R14: ffff98f143231708 R15: ffff98f14d7fb018
FS: 00007ec166097800(0000) GS:ffff98f1bbd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffc04ef420 CR3: 000000010ee9a000 CR4: 00000000003506e0
Call Trace:
temp_show+0x31/0x68
dev_attr_show+0x1d/0x4f
sysfs_kf_seq_show+0x92/0x107
seq_read_iter+0xf5/0x3f2
vfs_read+0x205/0x379
__x64_sys_read+0x7c/0xe2
do_syscall_64+0x43/0x55
entry_SYSCALL_64_after_hwframe+0x61/0xc6
if a thermal device is removed while accesses to its device attributes
are ongoing.
The problem is exposed by code in iwl_op_mode_mvm_start(), which registers
a thermal zone device only to unregister it shortly afterwards if an
unrelated failure is encountered while accessing the hardware.
Check if the thermal zone device is registered after acquiring the
thermal zone device mutex to ensure this does not happen.
The code was tested by triggering the failure in iwl_op_mode_mvm_start()
on purpose. Without this patch, the kernel crashes reliably. The crash
is no longer observed after applying this and the preceding patches.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46a891e45be97c6781ac34f5ec777d69370e252b ]
After enough invocations the LMh irq is eventually reported as bad, because the
handler doesn't return IRQ_HANDLED, fix this.
Fixes: 53bca371cd ("thermal/drivers/qcom: Add support for LMh driver")
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220316180322.88132-1-bjorn.andersson@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8763f8acbf8aef22a2321d4c978cd078aa3b8f64 ]
On gen2 chips the stage2 threshold is not 140 degC but 125 degC.
Make the warning message clearer by using this variable and also by
including the temperature that was checked for.
Fixes: aa92b3310c ("thermal/drivers/qcom-spmi-temp-alarm: Add support for GEN2 rev 1 PMIC peripherals")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Amit Kucheria <amitk@kernel.org>
Link: https://lore.kernel.org/r/20221020145237.942146-1-luca.weiss@fairphone.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d37edc7370273306d8747097fafa62436c1cfe16 ]
Check against the upper temperature limit (125 degrees C) before
consider the temperature valid.
Fixes: 5eed800a68 ("thermal: imx8mm: Add support for i.MX8MM thermal monitoring unit")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Link: https://lore.kernel.org/r/20221014073507.1594844-1-marcus.folkesson@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4748f9687caaeefab8578285b97b2f30789fc4b4 ]
In some error paths before device_register(), the names allocated
by dev_set_name() are not freed. Move dev_set_name() front to
device_register(), so the name can be freed while calling
put_device().
Fixes: 1dd7128b83 ("thermal/core: Fix null pointer dereference in thermal_release()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 68b99e94a4 ("thermal: intel_powerclamp: Use get_cpu() instead
of smp_processor_id() to avoid crash") fixed an issue related to using
smp_processor_id() in preemptible context by replacing it with a pair
of get_cpu()/put_cpu(), but what is needed there really is any online
CPU and not necessarily the one currently running the code. Arguably,
getting the one that's running the code in there is confusing.
For this reason, simply give the control CPU role to the first online
one which automatically will be CPU0 if it is online, so one check
can be dropped from the code for an added benefit.
Link: https://lore.kernel.org/linux-pm/20221011113646.GA12080@duo.ucw.cz/
Fixes: 68b99e94a4 ("thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Chen Yu <yu.c.chen@intel.com>
- Use platform data to get the sensor ID instead of parsing the device
in imx_sc thermal driver and remove the dedicated OF function from
the core code (Daniel Lezcano).
- Fix Kconfig dependency for the QCom tsens thermal driver (Jonathan
Cameron).
- Add missing const annotation to the RCar ops thermal driver (Lad
Prabhakar).
- Drop duplicate parameter check from
thermal_zone_device_register_with_trips() (Lad Prabhakar).
- Fix NULL pointer dereference in trip_point_temp_store() by making it
check if the ->set_trip_temp() operation is present (Lad Prabhakar).
- Fix the MSM8939 fourth sensor hardware ID in the QCom tsens thermal
driver (Vincent Knecht).
-----BEGIN PGP SIGNATURE-----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=BrtK
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These fix assorted issues in the thermal core and ARM thermal drivers.
Specifics:
- Use platform data to get the sensor ID instead of parsing the
device in imx_sc thermal driver and remove the dedicated OF
function from the core code (Daniel Lezcano).
- Fix Kconfig dependency for the QCom tsens thermal driver (Jonathan
Cameron).
- Add missing const annotation to the RCar ops thermal driver (Lad
Prabhakar).
- Drop duplicate parameter check from
thermal_zone_device_register_with_trips() (Lad Prabhakar).
- Fix NULL pointer dereference in trip_point_temp_store() by making
it check if the ->set_trip_temp() operation is present (Lad
Prabhakar).
- Fix the MSM8939 fourth sensor hardware ID in the QCom tsens thermal
driver (Vincent Knecht)"
* tag 'thermal-6.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/drivers/qcom/tsens-v0_1: Fix MSM8939 fourth sensor hw_id
thermal/core: Add a check before calling set_trip_temp()
thermal/core: Drop valid pointer check for type
thermal/drivers/rcar_thermal: Constify static thermal_zone_device_ops
thermal/drivers/qcom: Drop false build dependency of all QCOM drivers on QCOM_TSENS
thermal/of: Remove the thermal_zone_of_get_sensor_id() function
thermal/drivers/imx_sc: Rely on the platform data to get the resource id
Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and features,
the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0GQmA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylyVQCeNJjZ3hy+Wz8WkPSY+NkehuIhyCIAnjXMOJP8
5G/JQ+rpcclr7VOXlS66
=zVkU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
Core
----
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO.
This significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF
---
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions.
Expose crash_kexec() to allow BPF to trigger a kernel dump.
Use CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs.
Only structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols
---------
- WiFi: more Extremely High Throughput (EHT) and Multi-Link
Operation (MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state
and RST packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API
----------
- Allow selecting the conduit interface used by each port
in DSA switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting
per traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one
of the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much
as possible. It's one of those magic knobs which seemed like
a good idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers
----------------------
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers
-------
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay
window offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Gsio
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO. This
significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF:
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions. Expose
crash_kexec() to allow BPF to trigger a kernel dump. Use
CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs. Only
structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols:
- WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation
(MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state and RST
packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API:
- Allow selecting the conduit interface used by each port in DSA
switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting per
traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one of
the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much as
possible. It's one of those magic knobs which seemed like a good
idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers:
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers:
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay window
offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support"
* tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits)
eth: pse: add missing static inlines
once: rename _SLOW to _SLEEPABLE
net: pse-pd: add regulator based PSE driver
dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller
ethtool: add interface to interact with Ethernet Power Equipment
net: mdiobus: search for PSE nodes by parsing PHY nodes.
net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
net: add framework to support Ethernet PSE and PDs devices
dt-bindings: net: phy: add PoDL PSE property
net: marvell: prestera: Propagate nh state from hw to kernel
net: marvell: prestera: Add neighbour cache accounting
net: marvell: prestera: add stub handler neighbour events
net: marvell: prestera: Add heplers to interact with fib_notifier_info
net: marvell: prestera: Add length macros for prestera_ip_addr
net: marvell: prestera: add delayed wq and flush wq on deinit
net: marvell: prestera: Add strict cleanup of fib arbiter
net: marvell: prestera: Add cleanup of allocated fib_nodes
net: marvell: prestera: Add router nexthops ABI
eth: octeon: fix build after netif_napi_add() changes
net/mlx5: E-Switch, Return EBUSY if can't get mode lock
...
Drop the valid pointer check for type in
thermal_zone_device_register_with_trips() as we already have it confirmed
for != NULL from the previous if block.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220909181322.10933-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The only usage of rcar_thermal_zone_of_ops is to pass its address to
devm_thermal_of_zone_register(), which takes a pointer to const struct
thermal_zone_device_ops. Make it const to allow the compiler to put
it in read-only memory.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20220909182838.11154-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The SPMI QCOM drivers have no dependency in Kconfig, but the Makefile
will not be included without QCOM_TSENS. This unnecessarily reduces
build coverage.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Acked-by: Amit Kucheria <amitk@kernel.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20220821160032.2206349-1-jic23@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Currently the imx_sc driver is reimplementing part of the thermal zone
parsing from the thermal OF tree code to get the sensor id associated
with a thermal zone sensor.
The driver platform specific code should know what sensor is present
and not rely on the thermal zone description to do a discovery. Well
that is arguable but all the other drivers have a per platform data
telling what sensor id to use.
The imx_sc thermal driver is the only one using a different
approach. Not invalid but forcing to keep a specific function
'thermal_zone_of_get_sensor_id()' to get the sensor id for a specific
thermal zone as the self-explanatory function tells and having device
tree code inside the driver.
The thermal OF code had a rework and remains now self-encapsulated
with a register/unregister functions and their 'devm' variants, except
for the function mentioned above.
After investigating, it appears the imx_sc sensor is defined in
arch/arm64/boot/dts/freescale/imx8qxp.dtsi:
which defines the cpu-thermal zone with the id: IMX_SC_R_SYSTEM
This dtsi is included by:
- imx8qxp-ai_ml.dts
- imx8qxp-colibri.dtsi
- imx8qxp-mek.dts
The two first ones do not define more thermal zones
The third one adds the pmic-thermal0 zone with id: IMX_SC_R_PMIC_0
The thermal OF code returns -ENODEV if the thermal zone registration
with a specific id fails because the description is not available in
the DT for such a sensor id. In this case we continue with the other
ids without bailing out with an error.
So we can build for the 'fsl,imx-sc-thermal' a compatible data, an
array of sensor ids containing IMX_SC_R_SYSTEM and IMX_SC_R_PMIC_0.
The latter won't be found but that will not result in an error but a
normal case where we continue the initialization with other ids.
Just to clarify, it is what the thermal framework does and what the
other drivers are expecting: when a registration fails with -ENODEV
this is not an error but a case where the description is not found in
the device tree, that be can the entire thermal zones description or a
specific thermal zone with an unknown id.
There is one small functional change but without impact. When there is
no 'thermal-zones' description the probe function was returning
'-ENODEV', now it returns zero. When a thermal zone fails to register
with an error different from '-ENODEV', the error is detected and
returned.
Change the code accordingly and remove the OF code from the driver.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20220818082316.2717095-1-daniel.lezcano@linaro.org
Merge thermal control driver changes for 6.1-rc1:
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing).
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada).
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki).
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan).
- Drop redundant error message from da9062-thermal (zhaoxiao).
- Drop of_match_ptr() from thermal_mmio (Jean Delvare).
* thermal-intel:
thermal: int340x: processor_thermal: Use module_pci_driver() macro
thermal: intel_powerclamp: Remove accounting for IRQ wakes
thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash
thermal: int340x_thermal: Consolidate priv->data_vault checks
* thermal-drivers:
thermal: cpufreq_cooling: Check the policy first in cpufreq_cooling_register()
thermal: da9062-thermal: Drop redundant error message
thermal/drivers/thermal_mmio: Drop of_match_ptr()
Merge core thermal control changes for 6.1-rc1:
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar).
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang).
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki)
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after
free when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already showed in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
* thermal-core: (47 commits)
thermal: core: Increase maximum number of trip points
thermal: move from strlcpy() with unused retval to strscpy()
thermal: gov_user_space: Do not lock thermal zone mutex
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
thermal/core: Move set_trip_temp ops to the sysfs code
thermal/drivers/samsung: Switch to new of thermal API
regulator/drivers/max8976: Switch to new of thermal API
Input: sun4i-ts - switch to new of thermal API
iio/drivers/sun4i_gpadc: Switch to new of thermal API
hwmon/drivers/core: Switch to new of thermal API
hwmon: pm_bus: core: Switch to new of thermal API
ata/drivers/ahci_imx: Switch to new of thermal API
...
On one of the Chrome system, if we define more than 12 trip points,
probe for thermal sensor fails with
"int3403 thermal: probe of INTC1046:03 failed with error -22"
and throws an error as
"thermal_sys: Error: Incorrect number of thermal trips".
The thermal_zone_device_register() interface needs maximum
number of trip points supported in a zone as an argument.
This number can't exceed THERMAL_MAX_TRIPS, which is currently
set to 12. To address this issue, THERMAL_MAX_TRIPS value
has to be increased.
This interface also has an argument to specify a mask of trips
which are writable. This mask is defined as an int.
This mask sets the ceiling for increasing maximum number of
supported trips. With the current implementation, maximum number
of trips can be supported is 31.
Also, THERMAL_MAX_TRIPS macro is used in one place only.
So, remove THERMAL_MAX_TRIPS macro and compare num_trips
directly with using a macro BITS_PER_TYPE(int)-1.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since PCI provides helper macro module_pci_driver(), the
module_init/exit code can be replaced with it.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a static variable "idle_wakeup_counter", which accounts for
number of wake ups because of IRQs and take actions to compensate idle
injection. This is now read and reset to 0, but never incremented.
So all the usage of this counter for idle injection has no use.
Also another static variable "reduce_irq", which depends on
"idle_wakeup_counter", so remove usage of "reduce_irq" also.
Commit feb6cd6a0f ("thermal/intel_powerclamp: stop sched tick in
forced idle") replaced the local use of "mwait_idle_with_hints" with
play_idle(). This removed possibility of updating "idle_wakeup_counter"
without change in play_idle(). This change was made in Linux 4.10.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When CPU 0 is offline and intel_powerclamp is used to inject
idle, it generates kernel BUG:
BUG: using smp_processor_id() in preemptible [00000000] code: bash/15687
caller is debug_smp_processor_id+0x17/0x20
CPU: 4 PID: 15687 Comm: bash Not tainted 5.19.0-rc7+ #57
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x63
dump_stack+0x10/0x16
check_preemption_disabled+0xdd/0xe0
debug_smp_processor_id+0x17/0x20
powerclamp_set_cur_state+0x7f/0xf9 [intel_powerclamp]
...
...
Here CPU 0 is the control CPU by default and changed to the current CPU,
if CPU 0 offlined. This check has to be performed under cpus_read_lock(),
hence the above warning.
Use get_cpu() instead of smp_processor_id() to avoid this BUG.
Suggested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
-----BEGIN PGP SIGNATURE-----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=fUm6
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 6.1
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
* tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (142 commits)
iio: pressure: icp10100: Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS().
iio: adc: max1363: Drop provision to provide an IIO channel map via platform data
iio: accel: bma400: Add support for single and double tap events
iio: Add new event type gesture and use direction for single and double tap
iio: Use per-device lockdep class for mlock
iio: adc: add max11205 adc driver
dt-bindings: iio: adc: Add max11205 documentation file
iio: magnetometer: yamaha-yas530: Use dev_err_probe()
iio: magnetometer: yamaha-yas530: Make strings const in chip info
iio: magnetometer: yamaha-yas530: Use pointers as driver data
iio: adc: tsc2046: silent spi_device_id warning
iio: adc: tsc2046: add vref support
dt-bindings: iio: adc: ti,tsc2046: add vref-supply property
iio: light: ltrf216a: Add raw attribute
dt-bindings: iio: Add missing (unevaluated|additional)Properties on child nodes
MAINTAINERS: fix Analog Devices forum links
iio/accel: fix repeated words in comments
dt-bindings: iio: accel: add dt-binding schema for msa311 accel driver
iio: add MEMSensing MSA311 3-axis accelerometer driver
dt-bindings: vendor-prefixes: add MEMSensing Microsystems Co., Ltd.
...
It is sufficient to check priv->data_vault once in the error code path
of int3400_thermal_probe(), so do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since the policy needs to be accessed first when obtaining cpu devices,
first check whether the policy is legal before this.
Fixes: 5130802ddb ("thermal: cpu_cooling: Switch to QoS requests for freq limits")
Signed-off-by: Xuewen Yan <xuewen.yan@unisoc.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drop duplicate words from two kerneldoc comments in the thermal
subsystem.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
[ rjw: Subject edits and changelog rewrite ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
