Merge 6.1.16 into android14-6.1
Changes in 6.1.16
HID: asus: use spinlock to protect concurrent accesses
HID: asus: use spinlock to safely schedule workers
powerpc/mm: Rearrange if-else block to avoid clang warning
ata: ahci: Revert "ata: ahci: Add Tiger Lake UP{3,4} AHCI controller"
ARM: OMAP2+: Fix memory leak in realtime_counter_init()
arm64: dts: qcom: qcs404: use symbol names for PCIe resets
arm64: dts: qcom: msm8996-tone: Fix USB taking 6 minutes to wake up
arm64: dts: qcom: sm8150-kumano: Panel framebuffer is 2.5k instead of 4k
arm64: dts: qcom: sm6350: Fix up the ramoops node
arm64: dts: qcom: sm6125: Reorder HSUSB PHY clocks to match bindings
arm64: dts: qcom: sm6125-seine: Clean up gpio-keys (volume down)
arm64: dts: imx8m: Align SoC unique ID node unit address
ARM: zynq: Fix refcount leak in zynq_early_slcr_init
arm64: dts: mediatek: mt8195: Add power domain to U3PHY1 T-PHY
arm64: dts: mediatek: mt8183: Fix systimer 13 MHz clock description
arm64: dts: mediatek: mt8192: Fix systimer 13 MHz clock description
arm64: dts: mediatek: mt8195: Fix systimer 13 MHz clock description
arm64: dts: mediatek: mt8186: Fix systimer 13 MHz clock description
arm64: dts: qcom: sdm845-db845c: fix audio codec interrupt pin name
x86/acpi/boot: Do not register processors that cannot be onlined for x2APIC
arm64: dts: qcom: sc7180: correct SPMI bus address cells
arm64: dts: qcom: sc7280: correct SPMI bus address cells
arm64: dts: qcom: sc8280xp: correct SPMI bus address cells
arm64: dts: qcom: sc8280xp: Vote for CX in USB controllers
arm64: dts: meson-gxl: jethub-j80: Fix WiFi MAC address node
arm64: dts: meson-gxl: jethub-j80: Fix Bluetooth MAC node name
arm64: dts: meson-axg: jethub-j1xx: Fix MAC address node names
arm64: dts: meson-gx: Fix Ethernet MAC address unit name
arm64: dts: meson-g12a: Fix internal Ethernet PHY unit name
arm64: dts: meson-gx: Fix the SCPI DVFS node name and unit address
cpuidle, intel_idle: Fix CPUIDLE_FLAG_IRQ_ENABLE *again*
arm64: dts: ti: k3-am62: Enable SPI nodes at the board level
arm64: dts: ti: k3-am62-main: Fix clocks for McSPI
arm64: tegra: Fix duplicate regulator on Jetson TX1
arm64: dts: msm8992-bullhead: add memory hole region
arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem size
arm64: dts: qcom: msm8992-bullhead: Disable dfps_data_mem
arm64: dts: qcom: ipq8074: correct USB3 QMP PHY-s clock output names
arm64: dts: qcom: ipq8074: fix Gen2 PCIe QMP PHY
arm64: dts: qcom: ipq8074: fix Gen3 PCIe QMP PHY
arm64: dts: qcom: ipq8074: correct Gen2 PCIe ranges
arm64: dts: qcom: ipq8074: fix Gen3 PCIe node
arm64: dts: qcom: ipq8074: correct PCIe QMP PHY output clock names
arm64: dts: meson: remove CPU opps below 1GHz for G12A boards
ARM: OMAP1: call platform_device_put() in error case in omap1_dm_timer_init()
arm64: dts: mediatek: mt8192: Mark scp_adsp clock as broken
ARM: bcm2835_defconfig: Enable the framebuffer
ARM: s3c: fix s3c64xx_set_timer_source prototype
arm64: dts: ti: k3-j7200: Fix wakeup pinmux range
ARM: dts: exynos: correct wr-active property in Exynos3250 Rinato
ARM: imx: Call ida_simple_remove() for ida_simple_get
arm64: dts: amlogic: meson-gx: fix SCPI clock dvfs node name
arm64: dts: amlogic: meson-axg: fix SCPI clock dvfs node name
arm64: dts: amlogic: meson-gx: add missing SCPI sensors compatible
arm64: dts: amlogic: meson-axg-jethome-jethub-j1xx: fix supply name of USB controller node
arm64: dts: amlogic: meson-gxl-s905d-sml5442tw: drop invalid clock-names property
arm64: dts: amlogic: meson-gx: add missing unit address to rng node name
arm64: dts: amlogic: meson-gxl-s905w-jethome-jethub-j80: fix invalid rtc node name
arm64: dts: amlogic: meson-axg-jethome-jethub-j1xx: fix invalid rtc node name
arm64: dts: amlogic: meson-gxl: add missing unit address to eth-phy-mux node name
arm64: dts: amlogic: meson-gx-libretech-pc: fix update button name
arm64: dts: amlogic: meson-sm1-bananapi-m5: fix adc keys node names
arm64: dts: amlogic: meson-gxl-s905d-phicomm-n1: fix led node name
arm64: dts: amlogic: meson-gxbb-kii-pro: fix led node name
arm64: dts: amlogic: meson-sm1-odroid-hc4: fix active fan thermal trip
locking/rwsem: Disable preemption in all down_read*() and up_read() code paths
arm64: dts: renesas: beacon-renesom: Fix gpio expander reference
arm64: dts: meson: radxa-zero: allow usb otg mode
arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN
ARM: dts: sun8i: nanopi-duo2: Fix regulator GPIO reference
ublk_drv: remove nr_aborted_queues from ublk_device
ublk_drv: don't probe partitions if the ubq daemon isn't trusted
ARM: dts: imx7s: correct iomuxc gpr mux controller cells
sbitmap: remove redundant check in __sbitmap_queue_get_batch
sbitmap: Use single per-bitmap counting to wake up queued tags
sbitmap: correct wake_batch recalculation to avoid potential IO hung
arm64: dts: mt8195: Fix CPU map for single-cluster SoC
arm64: dts: mt8192: Fix CPU map for single-cluster SoC
arm64: dts: mt8186: Fix CPU map for single-cluster SoC
arm64: dts: mediatek: mt7622: Add missing pwm-cells to pwm node
arm64: dts: mediatek: mt8186: Fix watchdog compatible
arm64: dts: mediatek: mt8195: Fix watchdog compatible
arm64: dts: mediatek: mt7986: Fix watchdog compatible
ARM: dts: stm32: Update part number NVMEM description on stm32mp131
blk-mq: avoid sleep in blk_mq_alloc_request_hctx
blk-mq: remove stale comment for blk_mq_sched_mark_restart_hctx
blk-mq: wait on correct sbitmap_queue in blk_mq_mark_tag_wait
blk-mq: Fix potential io hung for shared sbitmap per tagset
blk-mq: correct stale comment of .get_budget
arm64: dts: qcom: msm8996: support using GPLL0 as kryocc input
arm64: dts: qcom: msm8996 switch from RPM_SMD_BB_CLK1 to RPM_SMD_XO_CLK_SRC
arm64: dts: qcom: sm8350: drop incorrect cells from serial
arm64: dts: qcom: sm8450: drop incorrect cells from serial
arm64: dts: qcom: msm8992-lg-bullhead: Correct memory overlaps with the SMEM and MPSS memory regions
arm64: dts: qcom: msm8953: correct TLMM gpio-ranges
arm64: dts: qcom: msm8992-*: Fix up comments
arm64: dts: qcom: msm8992-lg-bullhead: Enable regulators
s390/dasd: Fix potential memleak in dasd_eckd_init()
sched/rt: pick_next_rt_entity(): check list_entry
perf/x86/intel/ds: Fix the conversion from TSC to perf time
x86/perf/zhaoxin: Add stepping check for ZXC
KEYS: asymmetric: Fix ECDSA use via keyctl uapi
block: ublk: check IO buffer based on flag need_get_data
arm64: dts: qcom: pmk8350: Specify PBS register for PON
arm64: dts: qcom: pmk8350: Use the correct PON compatible
erofs: relinquish volume with mutex held
block: sync mixed merged request's failfast with 1st bio's
block: Fix io statistics for cgroup in throttle path
block: bio-integrity: Copy flags when bio_integrity_payload is cloned
block: use proper return value from bio_failfast()
wifi: mt76: mt7915: add missing of_node_put()
wifi: mt76: mt7921s: fix slab-out-of-bounds access in sdio host
wifi: mt76: mt7915: check return value before accessing free_block_num
wifi: mt76: mt7915: drop always true condition of __mt7915_reg_addr()
wifi: mt76: mt7915: fix unintended sign extension of mt7915_hw_queue_read()
wifi: mt76: fix coverity uninit_use_in_call in mt76_connac2_reverse_frag0_hdr_trans()
wifi: rsi: Fix memory leak in rsi_coex_attach()
wifi: rtlwifi: rtl8821ae: don't call kfree_skb() under spin_lock_irqsave()
wifi: rtlwifi: rtl8188ee: don't call kfree_skb() under spin_lock_irqsave()
wifi: rtlwifi: rtl8723be: don't call kfree_skb() under spin_lock_irqsave()
wifi: iwlegacy: common: don't call dev_kfree_skb() under spin_lock_irqsave()
wifi: libertas: fix memory leak in lbs_init_adapter()
wifi: rtl8xxxu: don't call dev_kfree_skb() under spin_lock_irqsave()
wifi: rtw89: 8852c: rfk: correct DACK setting
wifi: rtw89: 8852c: rfk: correct DPK settings
wifi: rtlwifi: Fix global-out-of-bounds bug in _rtl8812ae_phy_set_txpower_limit()
libbpf: Fix btf__align_of() by taking into account field offsets
wifi: ipw2x00: don't call dev_kfree_skb() under spin_lock_irqsave()
wifi: ipw2200: fix memory leak in ipw_wdev_init()
wifi: wilc1000: fix potential memory leak in wilc_mac_xmit()
wifi: wilc1000: add missing unregister_netdev() in wilc_netdev_ifc_init()
wifi: brcmfmac: fix potential memory leak in brcmf_netdev_start_xmit()
wifi: brcmfmac: unmap dma buffer in brcmf_msgbuf_alloc_pktid()
wifi: libertas_tf: don't call kfree_skb() under spin_lock_irqsave()
wifi: libertas: if_usb: don't call kfree_skb() under spin_lock_irqsave()
wifi: libertas: main: don't call kfree_skb() under spin_lock_irqsave()
wifi: libertas: cmdresp: don't call kfree_skb() under spin_lock_irqsave()
wifi: wl3501_cs: don't call kfree_skb() under spin_lock_irqsave()
libbpf: Fix invalid return address register in s390
crypto: x86/ghash - fix unaligned access in ghash_setkey()
ACPICA: Drop port I/O validation for some regions
genirq: Fix the return type of kstat_cpu_irqs_sum()
rcu-tasks: Improve comments explaining tasks_rcu_exit_srcu purpose
rcu-tasks: Remove preemption disablement around srcu_read_[un]lock() calls
rcu-tasks: Fix synchronize_rcu_tasks() VS zap_pid_ns_processes()
lib/mpi: Fix buffer overrun when SG is too long
crypto: ccp - Avoid page allocation failure warning for SEV_GET_ID2
platform/chrome: cros_ec_typec: Update port DP VDO
ACPICA: nsrepair: handle cases without a return value correctly
selftests/xsk: print correct payload for packet dump
selftests/xsk: print correct error codes when exiting
arm64/cpufeature: Fix field sign for DIT hwcap detection
kselftest/arm64: Fix syscall-abi for systems without 128 bit SME
workqueue: Protects wq_unbound_cpumask with wq_pool_attach_mutex
s390/early: fix sclp_early_sccb variable lifetime
s390/vfio-ap: fix an error handling path in vfio_ap_mdev_probe_queue()
x86/signal: Fix the value returned by strict_sas_size()
thermal/drivers/tsens: Drop msm8976-specific defines
thermal/drivers/tsens: Sort out msm8976 vs msm8956 data
thermal/drivers/tsens: fix slope values for msm8939
thermal/drivers/tsens: limit num_sensors to 9 for msm8939
wifi: rtw89: fix potential leak in rtw89_append_probe_req_ie()
wifi: rtw89: Add missing check for alloc_workqueue
wifi: rtl8xxxu: Fix memory leaks with RTL8723BU, RTL8192EU
wifi: orinoco: check return value of hermes_write_wordrec()
thermal/drivers/imx_sc_thermal: Drop empty platform remove function
thermal/drivers/imx_sc_thermal: Fix the loop condition
wifi: ath9k: htc_hst: free skb in ath9k_htc_rx_msg() if there is no callback function
wifi: ath9k: hif_usb: clean up skbs if ath9k_hif_usb_rx_stream() fails
wifi: ath9k: Fix potential stack-out-of-bounds write in ath9k_wmi_rsp_callback()
wifi: ath11k: Fix memory leak in ath11k_peer_rx_frag_setup
wifi: cfg80211: Fix extended KCK key length check in nl80211_set_rekey_data()
ACPI: battery: Fix missing NUL-termination with large strings
selftests/bpf: Fix build errors if CONFIG_NF_CONNTRACK=m
crypto: ccp - Failure on re-initialization due to duplicate sysfs filename
crypto: essiv - Handle EBUSY correctly
crypto: seqiv - Handle EBUSY correctly
powercap: fix possible name leak in powercap_register_zone()
x86/microcode: Add a parameter to microcode_check() to store CPU capabilities
x86/microcode: Check CPU capabilities after late microcode update correctly
x86/microcode: Adjust late loading result reporting message
selftests/bpf: Use consistent build-id type for liburandom_read.so
selftests/bpf: Fix vmtest static compilation error
crypto: xts - Handle EBUSY correctly
leds: led-class: Add missing put_device() to led_put()
s390/bpf: Add expoline to tail calls
wifi: iwlwifi: mei: fix compilation errors in rfkill()
kselftest/arm64: Fix enumeration of systems without 128 bit SME
can: rcar_canfd: Fix R-Car V3U GAFLCFG field accesses
selftests/bpf: Initialize tc in xdp_synproxy
crypto: ccp - Flush the SEV-ES TMR memory before giving it to firmware
bpftool: profile online CPUs instead of possible
wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work
wifi: mt76: mt7915: fix memory leak in mt7915_mcu_exit
wifi: mt76: mt7915: fix WED TxS reporting
wifi: mt76: add memory barrier to SDIO queue kick
wifi: mt76: mt7921: fix error code of return in mt7921_acpi_read
net/mlx5: Enhance debug print in page allocation failure
irqchip: Fix refcount leak in platform_irqchip_probe
irqchip/alpine-msi: Fix refcount leak in alpine_msix_init_domains
irqchip/irq-mvebu-gicp: Fix refcount leak in mvebu_gicp_probe
irqchip/ti-sci: Fix refcount leak in ti_sci_intr_irq_domain_probe
s390/mem_detect: fix detect_memory() error handling
s390/vmem: fix empty page tables cleanup under KASAN
s390/boot: cleanup decompressor header files
s390/mem_detect: rely on diag260() if sclp_early_get_memsize() fails
s390/boot: fix mem_detect extended area allocation
net: add sock_init_data_uid()
tun: tun_chr_open(): correctly initialize socket uid
tap: tap_open(): correctly initialize socket uid
OPP: fix error checking in opp_migrate_dentry()
cpufreq: davinci: Fix clk use after free
Bluetooth: hci_conn: Refactor hci_bind_bis() since it always succeeds
Bluetooth: L2CAP: Fix potential user-after-free
Bluetooth: hci_qca: get wakeup status from serdev device handle
net: ipa: generic command param fix
s390: vfio-ap: tighten the NIB validity check
s390/ap: fix status returned by ap_aqic()
s390/ap: fix status returned by ap_qact()
libbpf: Fix alen calculation in libbpf_nla_dump_errormsg()
xen/grant-dma-iommu: Implement a dummy probe_device() callback
rds: rds_rm_zerocopy_callback() correct order for list_add_tail()
crypto: rsa-pkcs1pad - Use akcipher_request_complete
m68k: /proc/hardware should depend on PROC_FS
RISC-V: time: initialize hrtimer based broadcast clock event device
clocksource/drivers/riscv: Patch riscv_clock_next_event() jump before first use
wifi: iwl3945: Add missing check for create_singlethread_workqueue
wifi: iwl4965: Add missing check for create_singlethread_workqueue()
wifi: mwifiex: fix loop iterator in mwifiex_update_ampdu_txwinsize()
selftests/bpf: Fix out-of-srctree build
ACPI: resource: Add IRQ overrides for MAINGEAR Vector Pro 2 models
ACPI: resource: Do IRQ override on all TongFang GMxRGxx
crypto: octeontx2 - Fix objects shared between several modules
crypto: crypto4xx - Call dma_unmap_page when done
wifi: mac80211: move color collision detection report in a delayed work
wifi: mac80211: make rate u32 in sta_set_rate_info_rx()
wifi: mac80211: fix non-MLO station association
wifi: mac80211: Don't translate MLD addresses for multicast
wifi: mac80211: avoid u32_encode_bits() warning
wifi: mac80211: fix off-by-one link setting
tools/lib/thermal: Fix thermal_sampling_exit()
thermal/drivers/hisi: Drop second sensor hi3660
selftests/bpf: Fix map_kptr test.
wifi: mac80211: pass 'sta' to ieee80211_rx_data_set_sta()
bpf: Zeroing allocated object from slab in bpf memory allocator
selftests/bpf: Fix xdp_do_redirect on s390x
can: esd_usb: Move mislocated storage of SJA1000_ECC_SEG bits in case of a bus error
can: esd_usb: Make use of can_change_state() and relocate checking skb for NULL
xsk: check IFF_UP earlier in Tx path
LoongArch, bpf: Use 4 instructions for function address in JIT
bpf: Fix global subprog context argument resolution logic
irqchip/irq-brcmstb-l2: Set IRQ_LEVEL for level triggered interrupts
irqchip/irq-bcm7120-l2: Set IRQ_LEVEL for level triggered interrupts
net/smc: fix potential panic dues to unprotected smc_llc_srv_add_link()
net/smc: fix application data exception
selftests/net: Interpret UDP_GRO cmsg data as an int value
l2tp: Avoid possible recursive deadlock in l2tp_tunnel_register()
net: bcmgenet: fix MoCA LED control
net: lan966x: Fix possible deadlock inside PTP
net/mlx4_en: Introduce flexible array to silence overflow warning
selftest: fib_tests: Always cleanup before exit
sefltests: netdevsim: wait for devlink instance after netns removal
drm: Fix potential null-ptr-deref due to drmm_mode_config_init()
drm/fourcc: Add missing big-endian XRGB1555 and RGB565 formats
drm/bridge: ti-sn65dsi83: Fix delay after reset deassert to match spec
drm: mxsfb: DRM_IMX_LCDIF should depend on ARCH_MXC
drm: mxsfb: DRM_MXSFB should depend on ARCH_MXS || ARCH_MXC
drm/bridge: megachips: Fix error handling in i2c_register_driver()
drm/vkms: Fix memory leak in vkms_init()
drm/vkms: Fix null-ptr-deref in vkms_release()
drm/vc4: dpi: Fix format mapping for RGB565
drm: tidss: Fix pixel format definition
gpu: ipu-v3: common: Add of_node_put() for reference returned by of_graph_get_port_by_id()
drm/vc4: drop all currently held locks if deadlock happens
hwmon: (ftsteutates) Fix scaling of measurements
drm/msm/dpu: check for null return of devm_kzalloc() in dpu_writeback_init()
drm/msm/hdmi: Add missing check for alloc_ordered_workqueue
pinctrl: qcom: pinctrl-msm8976: Correct function names for wcss pins
pinctrl: stm32: Fix refcount leak in stm32_pctrl_get_irq_domain
pinctrl: rockchip: Fix refcount leak in rockchip_pinctrl_parse_groups
drm/vc4: hvs: Set AXI panic modes
drm/vc4: hvs: SCALER_DISPBKGND_AUTOHS is only valid on HVS4
drm/vc4: hvs: Correct interrupt masking bit assignment for HVS5
drm/vc4: hvs: Fix colour order for xRGB1555 on HVS5
drm/vc4: hdmi: Correct interlaced timings again
drm/msm: clean event_thread->worker in case of an error
drm/panel-edp: fix name for IVO product id 854b
scsi: qla2xxx: Fix exchange oversubscription
scsi: qla2xxx: Fix exchange oversubscription for management commands
scsi: qla2xxx: edif: Fix clang warning
ASoC: fsl_sai: initialize is_dsp_mode flag
drm/bridge: tc358767: Set default CLRSIPO count
drm/msm/adreno: Fix null ptr access in adreno_gpu_cleanup()
ALSA: hda/ca0132: minor fix for allocation size
drm/amdgpu: Use the sched from entity for amdgpu_cs trace
drm/msm/gem: Add check for kmalloc
drm/msm/dpu: Disallow unallocated resources to be returned
drm/bridge: lt9611: fix sleep mode setup
drm/bridge: lt9611: fix HPD reenablement
drm/bridge: lt9611: fix polarity programming
drm/bridge: lt9611: fix programming of video modes
drm/bridge: lt9611: fix clock calculation
drm/bridge: lt9611: pass a pointer to the of node
regulator: tps65219: use IS_ERR() to detect an error pointer
drm/mipi-dsi: Fix byte order of 16-bit DCS set/get brightness
drm: exynos: dsi: Fix MIPI_DSI*_NO_* mode flags
drm/msm/dsi: Allow 2 CTRLs on v2.5.0
scsi: ufs: exynos: Fix DMA alignment for PAGE_SIZE != 4096
drm/msm/dpu: sc7180: add missing WB2 clock control
drm/msm: use strscpy instead of strncpy
drm/msm/dpu: Add check for cstate
drm/msm/dpu: Add check for pstates
drm/msm/mdp5: Add check for kzalloc
habanalabs: bugs fixes in timestamps buff alloc
pinctrl: bcm2835: Remove of_node_put() in bcm2835_of_gpio_ranges_fallback()
pinctrl: mediatek: Initialize variable pullen and pullup to zero
pinctrl: mediatek: Initialize variable *buf to zero
gpu: host1x: Fix mask for syncpoint increment register
gpu: host1x: Don't skip assigning syncpoints to channels
drm/tegra: firewall: Check for is_addr_reg existence in IMM check
pinctrl: renesas: rzg2l: Fix configuring the GPIO pins as interrupts
drm/msm/dpu: set pdpu->is_rt_pipe early in dpu_plane_sspp_atomic_update()
drm/mediatek: dsi: Reduce the time of dsi from LP11 to sending cmd
drm/mediatek: Use NULL instead of 0 for NULL pointer
drm/mediatek: Drop unbalanced obj unref
drm/mediatek: mtk_drm_crtc: Add checks for devm_kcalloc
drm/mediatek: Clean dangling pointer on bind error path
ASoC: soc-compress.c: fixup private_data on snd_soc_new_compress()
dt-bindings: display: mediatek: Fix the fallback for mediatek,mt8186-disp-ccorr
gpio: vf610: connect GPIO label to dev name
ASoC: topology: Properly access value coming from topology file
spi: dw_bt1: fix MUX_MMIO dependencies
ASoC: mchp-spdifrx: fix controls which rely on rsr register
ASoC: mchp-spdifrx: fix return value in case completion times out
ASoC: mchp-spdifrx: fix controls that works with completion mechanism
ASoC: mchp-spdifrx: disable all interrupts in mchp_spdifrx_dai_remove()
dm: improve shrinker debug names
regmap: apply reg_base and reg_downshift for single register ops
ASoC: rsnd: fixup #endif position
ASoC: mchp-spdifrx: Fix uninitialized use of mr in mchp_spdifrx_hw_params()
ASoC: dt-bindings: meson: fix gx-card codec node regex
regulator: tps65219: use generic set_bypass()
hwmon: (asus-ec-sensors) add missing mutex path
hwmon: (ltc2945) Handle error case in ltc2945_value_store
ALSA: hda: Fix the control element identification for multiple codecs
drm/amdgpu: fix enum odm_combine_mode mismatch
scsi: mpt3sas: Fix a memory leak
scsi: aic94xx: Add missing check for dma_map_single()
HID: multitouch: Add quirks for flipped axes
HID: retain initial quirks set up when creating HID devices
ASoC: qcom: q6apm-lpass-dai: unprepare stream if its already prepared
ASoC: qcom: q6apm-dai: fix race condition while updating the position pointer
ASoC: qcom: q6apm-dai: Add SNDRV_PCM_INFO_BATCH flag
ASoC: codecs: lpass: register mclk after runtime pm
ASoC: codecs: lpass: fix incorrect mclk rate
drm/amd/display: don't call dc_interrupt_set() for disabled crtcs
HID: logitech-hidpp: Hard-code HID++ 1.0 fast scroll support
spi: bcm63xx-hsspi: Fix multi-bit mode setting
hwmon: (mlxreg-fan) Return zero speed for broken fan
ASoC: tlv320adcx140: fix 'ti,gpio-config' DT property init
dm: remove flush_scheduled_work() during local_exit()
nfs4trace: fix state manager flag printing
NFS: fix disabling of swap
spi: synquacer: Fix timeout handling in synquacer_spi_transfer_one()
ASoC: soc-dapm.h: fixup warning struct snd_pcm_substream not declared
HID: bigben: use spinlock to protect concurrent accesses
HID: bigben_worker() remove unneeded check on report_field
HID: bigben: use spinlock to safely schedule workers
hid: bigben_probe(): validate report count
ALSA: hda/hdmi: Register with vga_switcheroo on Dual GPU Macbooks
drm/shmem-helper: Fix locking for drm_gem_shmem_get_pages_sgt()
NFSD: enhance inter-server copy cleanup
NFSD: fix leaked reference count of nfsd4_ssc_umount_item
nfsd: fix race to check ls_layouts
nfsd: clean up potential nfsd_file refcount leaks in COPY codepath
NFSD: fix problems with cleanup on errors in nfsd4_copy
nfsd: fix courtesy client with deny mode handling in nfs4_upgrade_open
nfsd: don't fsync nfsd_files on last close
NFSD: copy the whole verifier in nfsd_copy_write_verifier
cifs: Fix lost destroy smbd connection when MR allocate failed
cifs: Fix warning and UAF when destroy the MR list
cifs: use tcon allocation functions even for dummy tcon
gfs2: jdata writepage fix
perf llvm: Fix inadvertent file creation
leds: led-core: Fix refcount leak in of_led_get()
leds: is31fl319x: Wrap mutex_destroy() for devm_add_action_or_rest()
leds: simatic-ipc-leds-gpio: Make sure we have the GPIO providing driver
tools/tracing/rtla: osnoise_hist: use total duration for average calculation
perf inject: Use perf_data__read() for auxtrace
perf intel-pt: Do not try to queue auxtrace data on pipe
perf test bpf: Skip test if kernel-debuginfo is not present
perf tools: Fix auto-complete on aarch64
sparc: allow PM configs for sparc32 COMPILE_TEST
selftests: find echo binary to use -ne options
selftests/ftrace: Fix bash specific "==" operator
selftests: use printf instead of echo -ne
perf record: Fix segfault with --overwrite and --max-size
printf: fix errname.c list
perf tests stat_all_metrics: Change true workload to sleep workload for system wide check
objtool: add UACCESS exceptions for __tsan_volatile_read/write
mfd: cs5535: Don't build on UML
mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
dmaengine: idxd: Set traffic class values in GRPCFG on DSA 2.0
RDMA/erdma: Fix refcount leak in erdma_mmap
dmaengine: HISI_DMA should depend on ARCH_HISI
RDMA/hns: Fix refcount leak in hns_roce_mmap
iio: light: tsl2563: Do not hardcode interrupt trigger type
usb: gadget: fusb300_udc: free irq on the error path in fusb300_probe()
i2c: designware: fix i2c_dw_clk_rate() return size to be u32
soundwire: cadence: Don't overflow the command FIFOs
driver core: fix potential null-ptr-deref in device_add()
kobject: modify kobject_get_path() to take a const *
kobject: Fix slab-out-of-bounds in fill_kobj_path()
alpha/boot/tools/objstrip: fix the check for ELF header
media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible()
media: uvcvideo: Implement mask for V4L2_CTRL_TYPE_MENU
media: uvcvideo: Refactor uvc_ctrl_mappings_uvcXX
media: uvcvideo: Refactor power_line_frequency_controls_limited
coresight: etm4x: Fix accesses to TRCSEQRSTEVR and TRCSEQSTR
coresight: cti: Prevent negative values of enable count
coresight: cti: Add PM runtime call in enable_store
usb: typec: intel_pmc_mux: Don't leak the ACPI device reference count
PCI/IOV: Enlarge virtfn sysfs name buffer
PCI: switchtec: Return -EFAULT for copy_to_user() errors
PCI: endpoint: pci-epf-vntb: Clean up kernel_doc warning
PCI: endpoint: pci-epf-vntb: Add epf_ntb_mw_bar_clear() num_mws kernel-doc
hwtracing: hisi_ptt: Only add the supported devices to the filters list
tty: serial: fsl_lpuart: disable Rx/Tx DMA in lpuart32_shutdown()
tty: serial: fsl_lpuart: clear LPUART Status Register in lpuart32_shutdown()
serial: tegra: Add missing clk_disable_unprepare() in tegra_uart_hw_init()
Revert "char: pcmcia: cm4000_cs: Replace mdelay with usleep_range in set_protocol"
eeprom: idt_89hpesx: Fix error handling in idt_init()
applicom: Fix PCI device refcount leak in applicom_init()
firmware: stratix10-svc: add missing gen_pool_destroy() in stratix10_svc_drv_probe()
firmware: stratix10-svc: fix error handle while alloc/add device failed
VMCI: check context->notify_page after call to get_user_pages_fast() to avoid GPF
mei: pxp: Use correct macros to initialize uuid_le
misc/mei/hdcp: Use correct macros to initialize uuid_le
misc: fastrpc: Fix an error handling path in fastrpc_rpmsg_probe()
driver core: fix resource leak in device_add()
driver core: location: Free struct acpi_pld_info *pld before return false
drivers: base: transport_class: fix possible memory leak
drivers: base: transport_class: fix resource leak when transport_add_device() fails
firmware: dmi-sysfs: Fix null-ptr-deref in dmi_sysfs_register_handle
fotg210-udc: Add missing completion handler
dmaengine: dw-edma: Fix missing src/dst address of interleaved xfers
fpga: microchip-spi: move SPI I/O buffers out of stack
fpga: microchip-spi: rewrite status polling in a time measurable way
usb: early: xhci-dbc: Fix a potential out-of-bound memory access
tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case
RDMA/cxgb4: add null-ptr-check after ip_dev_find()
usb: musb: mediatek: don't unregister something that wasn't registered
usb: gadget: configfs: Restrict symlink creation is UDC already binded
phy: mediatek: remove temporary variable @mask_
PCI: mt7621: Delay phy ports initialization
iommu: dart: Add suspend/resume support
iommu: dart: Support >64 stream IDs
iommu/dart: Fix apple_dart_device_group for PCI groups
iommu/vt-d: Set No Execute Enable bit in PASID table entry
power: supply: remove faulty cooling logic
RDMA/cxgb4: Fix potential null-ptr-deref in pass_establish()
usb: max-3421: Fix setting of I/O pins
RDMA/irdma: Cap MSIX used to online CPUs + 1
serial: fsl_lpuart: fix RS485 RTS polariy inverse issue
tty: serial: imx: Handle RS485 DE signal active high
tty: serial: imx: disable Ageing Timer interrupt request irq
driver core: fw_devlink: Add DL_FLAG_CYCLE support to device links
driver core: fw_devlink: Don't purge child fwnode's consumer links
driver core: fw_devlink: Allow marking a fwnode link as being part of a cycle
driver core: fw_devlink: Consolidate device link flag computation
driver core: fw_devlink: Improve check for fwnode with no device/driver
driver core: fw_devlink: Make cycle detection more robust
mtd: mtdpart: Don't create platform device that'll never probe
usb: host: fsl-mph-dr-of: reuse device_set_of_node_from_dev
dmaengine: dw-edma: Fix readq_ch() return value truncation
PCI: Fix dropping valid root bus resources with .end = zero
phy: rockchip-typec: fix tcphy_get_mode error case
PCI: qcom: Fix host-init error handling
iw_cxgb4: Fix potential NULL dereference in c4iw_fill_res_cm_id_entry()
iommu: Fix error unwind in iommu_group_alloc()
iommu/amd: Do not identity map v2 capable device when snp is enabled
dmaengine: sf-pdma: pdma_desc memory leak fix
dmaengine: dw-axi-dmac: Do not dereference NULL structure
dmaengine: ptdma: check for null desc before calling pt_cmd_callback
iommu/vt-d: Fix error handling in sva enable/disable paths
iommu/vt-d: Allow to use flush-queue when first level is default
RDMA/rxe: cleanup some error handling in rxe_verbs.c
RDMA/rxe: Fix missing memory barriers in rxe_queue.h
IB/hfi1: Fix math bugs in hfi1_can_pin_pages()
IB/hfi1: Fix sdma.h tx->num_descs off-by-one errors
Revert "remoteproc: qcom_q6v5_mss: map/unmap metadata region before/after use"
remoteproc: qcom_q6v5_mss: Use a carveout to authenticate modem headers
media: ti: cal: fix possible memory leak in cal_ctx_create()
media: platform: ti: Add missing check for devm_regulator_get
media: imx: imx7-media-csi: fix missing clk_disable_unprepare() in imx7_csi_init()
powerpc: Remove linker flag from KBUILD_AFLAGS
s390/vdso: Drop '-shared' from KBUILD_CFLAGS_64
builddeb: clean generated package content
media: max9286: Fix memleak in max9286_v4l2_register()
media: ov2740: Fix memleak in ov2740_init_controls()
media: ov5675: Fix memleak in ov5675_init_controls()
media: ov5640: Fix soft reset sequence and timings
media: ov5640: Handle delays when no reset_gpio set
media: mc: Get media_device directly from pad
media: i2c: ov772x: Fix memleak in ov772x_probe()
media: i2c: imx219: Split common registers from mode tables
media: i2c: imx219: Fix binning for RAW8 capture
media: platform: mtk-mdp3: Fix return value check in mdp_probe()
media: camss: csiphy-3ph: avoid undefined behavior
media: platform: mtk-mdp3: remove unused VIDEO_MEDIATEK_VPU config
media: platform: mtk-mdp3: fix Kconfig dependencies
media: v4l2-jpeg: correct the skip count in jpeg_parse_app14_data
media: v4l2-jpeg: ignore the unknown APP14 marker
media: hantro: Fix JPEG encoder ENUM_FRMSIZE on RK3399
media: imx-jpeg: Apply clk_bulk api instead of operating specific clk
media: amphion: correct the unspecified color space
media: drivers/media/v4l2-core/v4l2-h264 : add detection of null pointers
media: rc: Fix use-after-free bugs caused by ene_tx_irqsim()
media: atomisp: Only set default_run_mode on first open of a stream/asd
media: i2c: ov7670: 0 instead of -EINVAL was returned
media: usb: siano: Fix use after free bugs caused by do_submit_urb
media: saa7134: Use video_unregister_device for radio_dev
rpmsg: glink: Avoid infinite loop on intent for missing channel
rpmsg: glink: Release driver_override
ARM: OMAP2+: omap4-common: Fix refcount leak bug
arm64: dts: qcom: msm8996: Add additional A2NoC clocks
udf: Define EFSCORRUPTED error code
context_tracking: Fix noinstr vs KASAN
exit: Detect and fix irq disabled state in oops
ARM: dts: exynos: Use Exynos5420 compatible for the MIPI video phy
fs: Use CHECK_DATA_CORRUPTION() when kernel bugs are detected
blk-iocost: fix divide by 0 error in calc_lcoefs()
blk-cgroup: dropping parent refcount after pd_free_fn() is done
blk-cgroup: synchronize pd_free_fn() from blkg_free_workfn() and blkcg_deactivate_policy()
trace/blktrace: fix memory leak with using debugfs_lookup()
btrfs: scrub: improve tree block error reporting
arm64: zynqmp: Enable hs termination flag for USB dwc3 controller
cpuidle, intel_idle: Fix CPUIDLE_FLAG_INIT_XSTATE
x86/fpu: Don't set TIF_NEED_FPU_LOAD for PF_IO_WORKER threads
cpuidle: drivers: firmware: psci: Dont instrument suspend code
cpuidle: lib/bug: Disable rcu_is_watching() during WARN/BUG
perf/x86/intel/uncore: Add Meteor Lake support
wifi: ath9k: Fix use-after-free in ath9k_hif_usb_disconnect()
wifi: ath11k: fix monitor mode bringup crash
wifi: brcmfmac: Fix potential stack-out-of-bounds in brcmf_c_preinit_dcmds()
rcu: Make RCU_LOCKDEP_WARN() avoid early lockdep checks
rcu: Suppress smp_processor_id() complaint in synchronize_rcu_expedited_wait()
srcu: Delegate work to the boot cpu if using SRCU_SIZE_SMALL
rcu-tasks: Make rude RCU-Tasks work well with CPU hotplug
rcu-tasks: Handle queue-shrink/callback-enqueue race condition
wifi: ath11k: debugfs: fix to work with multiple PCI devices
thermal: intel: Fix unsigned comparison with less than zero
timers: Prevent union confusion from unexpected restart_syscall()
x86/bugs: Reset speculation control settings on init
bpftool: Always disable stack protection for BPF objects
wifi: brcmfmac: ensure CLM version is null-terminated to prevent stack-out-of-bounds
wifi: mt7601u: fix an integer underflow
inet: fix fast path in __inet_hash_connect()
ice: restrict PTP HW clock freq adjustments to 100, 000, 000 PPB
ice: add missing checks for PF vsi type
ACPI: Don't build ACPICA with '-Os'
bpf, docs: Fix modulo zero, division by zero, overflow, and underflow
thermal: intel: intel_pch: Add support for Wellsburg PCH
clocksource: Suspend the watchdog temporarily when high read latency detected
crypto: hisilicon: Wipe entire pool on error
net: bcmgenet: Add a check for oversized packets
m68k: Check syscall_trace_enter() return code
s390/mm,ptdump: avoid Kasan vs Memcpy Real markers swapping
netfilter: nf_tables: NULL pointer dereference in nf_tables_updobj()
can: isotp: check CAN address family in isotp_bind()
gcc-plugins: drop -std=gnu++11 to fix GCC 13 build
tools/power/x86/intel-speed-select: Add Emerald Rapid quirk
wifi: mt76: dma: free rx_head in mt76_dma_rx_cleanup
ACPI: video: Fix Lenovo Ideapad Z570 DMI match
net/mlx5: fw_tracer: Fix debug print
coda: Avoid partial allocation of sig_inputArgs
uaccess: Add minimum bounds check on kernel buffer size
s390/idle: mark arch_cpu_idle() noinstr
time/debug: Fix memory leak with using debugfs_lookup()
PM: domains: fix memory leak with using debugfs_lookup()
PM: EM: fix memory leak with using debugfs_lookup()
Bluetooth: Fix issue with Actions Semi ATS2851 based devices
Bluetooth: btusb: Add new PID/VID 0489:e0f2 for MT7921
Bluetooth: btusb: Add VID:PID 13d3:3529 for Realtek RTL8821CE
wifi: rtw89: debug: avoid invalid access on RTW89_DBG_SEL_MAC_30
hv_netvsc: Check status in SEND_RNDIS_PKT completion message
s390/kfence: fix page fault reporting
devlink: Fix TP_STRUCT_entry in trace of devlink health report
scm: add user copy checks to put_cmsg()
drm: panel-orientation-quirks: Add quirk for Lenovo Yoga Tab 3 X90F
drm: panel-orientation-quirks: Add quirk for DynaBook K50
drm/amd/display: Reduce expected sdp bandwidth for dcn321
drm/amd/display: Revert Reduce delay when sink device not able to ACK 00340h write
drm/amd/display: Fix potential null-deref in dm_resume
drm/omap: dsi: Fix excessive stack usage
HID: Add Mapping for System Microphone Mute
drm/tiny: ili9486: Do not assume 8-bit only SPI controllers
drm/amd/display: Defer DIG FIFO disable after VID stream enable
drm/radeon: free iio for atombios when driver shutdown
drm/amd: Avoid BUG() for case of SRIOV missing IP version
drm/amdkfd: Page aligned memory reserve size
scsi: lpfc: Fix use-after-free KFENCE violation during sysfs firmware write
Revert "fbcon: don't lose the console font across generic->chip driver switch"
drm/amd: Avoid ASSERT for some message failures
drm: amd: display: Fix memory leakage
drm/amd/display: fix mapping to non-allocated address
HID: uclogic: Add frame type quirk
HID: uclogic: Add battery quirk
HID: uclogic: Add support for XP-PEN Deco Pro SW
HID: uclogic: Add support for XP-PEN Deco Pro MW
drm/msm/dsi: Add missing check for alloc_ordered_workqueue
drm: rcar-du: Add quirk for H3 ES1.x pclk workaround
drm: rcar-du: Fix setting a reserved bit in DPLLCR
drm/drm_print: correct format problem
drm/amd/display: Set hvm_enabled flag for S/G mode
habanalabs: extend fatal messages to contain PCI info
habanalabs: fix bug in timestamps registration code
docs/scripts/gdb: add necessary make scripts_gdb step
drm/msm/dpu: Add DSC hardware blocks to register snapshot
ASoC: soc-compress: Reposition and add pcm_mutex
ASoC: kirkwood: Iterate over array indexes instead of using pointer math
regulator: max77802: Bounds check regulator id against opmode
regulator: s5m8767: Bounds check id indexing into arrays
Revert "drm/amdgpu: TA unload messages are not actually sent to psp when amdgpu is uninstalled"
drm/amd/display: fix FCLK pstate change underflow
gfs2: Improve gfs2_make_fs_rw error handling
hwmon: (coretemp) Simplify platform device handling
hwmon: (nct6775) Directly call ASUS ACPI WMI method
hwmon: (nct6775) B650/B660/X670 ASUS boards support
pinctrl: at91: use devm_kasprintf() to avoid potential leaks
drm/amd/display: Do not commit pipe when updating DRR
scsi: snic: Fix memory leak with using debugfs_lookup()
scsi: ufs: core: Fix device management cmd timeout flow
HID: logitech-hidpp: Don't restart communication if not necessary
drm/amd/display: Enable P-state validation checks for DCN314
drm: panel-orientation-quirks: Add quirk for Lenovo IdeaPad Duet 3 10IGL5
drm/amd/display: Disable HUBP/DPP PG on DCN314 for now
dm thin: add cond_resched() to various workqueue loops
dm cache: add cond_resched() to various workqueue loops
nfsd: zero out pointers after putting nfsd_files on COPY setup error
nfsd: don't hand out delegation on setuid files being opened for write
cifs: prevent data race in smb2_reconnect()
drm/shmem-helper: Revert accidental non-GPL export
driver core: fw_devlink: Avoid spurious error message
wifi: rtl8xxxu: fixing transmisison failure for rtl8192eu
scsi: mpt3sas: Remove usage of dma_get_required_mask() API
firmware: coreboot: framebuffer: Ignore reserved pixel color bits
block: don't allow multiple bios for IOCB_NOWAIT issue
block: clear bio->bi_bdev when putting a bio back in the cache
block: be a bit more careful in checking for NULL bdev while polling
rtc: pm8xxx: fix set-alarm race
ipmi: ipmb: Fix the MODULE_PARM_DESC associated to 'retry_time_ms'
ipmi:ssif: resend_msg() cannot fail
ipmi_ssif: Rename idle state and check
io_uring: Replace 0-length array with flexible array
io_uring: use user visible tail in io_uring_poll()
io_uring: handle TIF_NOTIFY_RESUME when checking for task_work
io_uring: add a conditional reschedule to the IOPOLL cancelation loop
io_uring: add reschedule point to handle_tw_list()
io_uring/rsrc: disallow multi-source reg buffers
io_uring: remove MSG_NOSIGNAL from recvmsg
io_uring: fix fget leak when fs don't support nowait buffered read
s390/extmem: return correct segment type in __segment_load()
s390: discard .interp section
s390/kprobes: fix irq mask clobbering on kprobe reenter from post_handler
s390/kprobes: fix current_kprobe never cleared after kprobes reenter
KVM: s390: disable migration mode when dirty tracking is disabled
cifs: Fix uninitialized memory read in smb3_qfs_tcon()
cifs: Fix uninitialized memory reads for oparms.mode
cifs: fix mount on old smb servers
cifs: introduce cifs_io_parms in smb2_async_writev()
cifs: split out smb3_use_rdma_offload() helper
cifs: don't try to use rdma offload on encrypted connections
cifs: Check the lease context if we actually got a lease
cifs: return a single-use cfid if we did not get a lease
scsi: mpi3mr: Fix missing mrioc->evtack_cmds initialization
scsi: mpi3mr: Fix issues in mpi3mr_get_all_tgt_info()
scsi: mpi3mr: Remove unnecessary memcpy() to alltgt_info->dmi
btrfs: hold block group refcount during async discard
locking/rwsem: Prevent non-first waiter from spinning in down_write() slowpath
ksmbd: fix wrong data area length for smb2 lock request
ksmbd: do not allow the actual frame length to be smaller than the rfc1002 length
ksmbd: fix possible memory leak in smb2_lock()
torture: Fix hang during kthread shutdown phase
ARM: dts: exynos: correct HDMI phy compatible in Exynos4
io_uring: mark task TASK_RUNNING before handling resume/task work
hfs: fix missing hfs_bnode_get() in __hfs_bnode_create
fs: hfsplus: fix UAF issue in hfsplus_put_super
exfat: fix reporting fs error when reading dir beyond EOF
exfat: fix unexpected EOF while reading dir
exfat: redefine DIR_DELETED as the bad cluster number
exfat: fix inode->i_blocks for non-512 byte sector size device
fs: dlm: don't set stop rx flag after node reset
fs: dlm: move sending fin message into state change handling
fs: dlm: send FIN ack back in right cases
f2fs: fix information leak in f2fs_move_inline_dirents()
f2fs: retry to update the inode page given data corruption
f2fs: fix cgroup writeback accounting with fs-layer encryption
f2fs: fix kernel crash due to null io->bio
ocfs2: fix defrag path triggering jbd2 ASSERT
ocfs2: fix non-auto defrag path not working issue
fs/cramfs/inode.c: initialize file_ra_state
selftests/landlock: Skip overlayfs tests when not supported
selftests/landlock: Test ptrace as much as possible with Yama
udf: Truncate added extents on failed expansion
udf: Do not bother merging very long extents
udf: Do not update file length for failed writes to inline files
udf: Preserve link count of system files
udf: Detect system inodes linked into directory hierarchy
udf: Fix file corruption when appending just after end of preallocated extent
md: don't update recovery_cp when curr_resync is ACTIVE
RDMA/siw: Fix user page pinning accounting
KVM: Destroy target device if coalesced MMIO unregistration fails
KVM: VMX: Fix crash due to uninitialized current_vmcs
KVM: Register /dev/kvm as the _very_ last thing during initialization
KVM: x86: Purge "highest ISR" cache when updating APICv state
KVM: x86: Blindly get current x2APIC reg value on "nodecode write" traps
KVM: x86: Don't inhibit APICv/AVIC on xAPIC ID "change" if APIC is disabled
KVM: x86: Don't inhibit APICv/AVIC if xAPIC ID mismatch is due to 32-bit ID
KVM: SVM: Flush the "current" TLB when activating AVIC
KVM: SVM: Process ICR on AVIC IPI delivery failure due to invalid target
KVM: SVM: Don't put/load AVIC when setting virtual APIC mode
KVM: x86: Inject #GP if WRMSR sets reserved bits in APIC Self-IPI
KVM: x86: Inject #GP on x2APIC WRMSR that sets reserved bits 63:32
KVM: SVM: Fix potential overflow in SEV's send|receive_update_data()
KVM: SVM: hyper-v: placate modpost section mismatch error
selftests: x86: Fix incorrect kernel headers search path
x86/virt: Force GIF=1 prior to disabling SVM (for reboot flows)
x86/crash: Disable virt in core NMI crash handler to avoid double shootdown
x86/reboot: Disable virtualization in an emergency if SVM is supported
x86/reboot: Disable SVM, not just VMX, when stopping CPUs
x86/kprobes: Fix __recover_optprobed_insn check optimizing logic
x86/kprobes: Fix arch_check_optimized_kprobe check within optimized_kprobe range
x86/microcode/amd: Remove load_microcode_amd()'s bsp parameter
x86/microcode/AMD: Add a @cpu parameter to the reloading functions
x86/microcode/AMD: Fix mixed steppings support
x86/speculation: Allow enabling STIBP with legacy IBRS
Documentation/hw-vuln: Document the interaction between IBRS and STIBP
virt/sev-guest: Return -EIO if certificate buffer is not large enough
brd: mark as nowait compatible
brd: return 0/-error from brd_insert_page()
brd: check for REQ_NOWAIT and set correct page allocation mask
ima: fix error handling logic when file measurement failed
ima: Align ima_file_mmap() parameters with mmap_file LSM hook
selftests/powerpc: Fix incorrect kernel headers search path
selftests/ftrace: Fix eprobe syntax test case to check filter support
selftests: sched: Fix incorrect kernel headers search path
selftests: core: Fix incorrect kernel headers search path
selftests: pid_namespace: Fix incorrect kernel headers search path
selftests: arm64: Fix incorrect kernel headers search path
selftests: clone3: Fix incorrect kernel headers search path
selftests: pidfd: Fix incorrect kernel headers search path
selftests: membarrier: Fix incorrect kernel headers search path
selftests: kcmp: Fix incorrect kernel headers search path
selftests: media_tests: Fix incorrect kernel headers search path
selftests: gpio: Fix incorrect kernel headers search path
selftests: filesystems: Fix incorrect kernel headers search path
selftests: user_events: Fix incorrect kernel headers search path
selftests: ptp: Fix incorrect kernel headers search path
selftests: sync: Fix incorrect kernel headers search path
selftests: rseq: Fix incorrect kernel headers search path
selftests: move_mount_set_group: Fix incorrect kernel headers search path
selftests: mount_setattr: Fix incorrect kernel headers search path
selftests: perf_events: Fix incorrect kernel headers search path
selftests: ipc: Fix incorrect kernel headers search path
selftests: futex: Fix incorrect kernel headers search path
selftests: drivers: Fix incorrect kernel headers search path
selftests: dmabuf-heaps: Fix incorrect kernel headers search path
selftests: vm: Fix incorrect kernel headers search path
selftests: seccomp: Fix incorrect kernel headers search path
irqdomain: Fix association race
irqdomain: Fix disassociation race
irqdomain: Look for existing mapping only once
irqdomain: Drop bogus fwspec-mapping error handling
irqdomain: Refactor __irq_domain_alloc_irqs()
irqdomain: Fix mapping-creation race
irqdomain: Fix domain registration race
crypto: qat - fix out-of-bounds read
mm/damon/paddr: fix missing folio_put()
ALSA: ice1712: Do not left ice->gpio_mutex locked in aureon_add_controls()
ALSA: hda/realtek: Add quirk for HP EliteDesk 800 G6 Tower PC
jbd2: fix data missing when reusing bh which is ready to be checkpointed
ext4: optimize ea_inode block expansion
ext4: refuse to create ea block when umounted
cxl/pmem: Fix nvdimm registration races
mtd: spi-nor: sfdp: Fix index value for SCCR dwords
mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
dm: send just one event on resize, not two
dm: add cond_resched() to dm_wq_work()
dm: add cond_resched() to dm_wq_requeue_work()
wifi: rtw88: use RTW_FLAG_POWERON flag to prevent to power on/off twice
wifi: rtl8xxxu: Use a longer retry limit of 48
wifi: ath11k: allow system suspend to survive ath11k
wifi: cfg80211: Fix use after free for wext
wifi: cfg80211: Set SSID if it is not already set
cpuidle: add ARCH_SUSPEND_POSSIBLE dependencies
qede: fix interrupt coalescing configuration
thermal: intel: powerclamp: Fix cur_state for multi package system
dm flakey: fix logic when corrupting a bio
dm cache: free background tracker's queued work in btracker_destroy
dm flakey: don't corrupt the zero page
dm flakey: fix a bug with 32-bit highmem systems
hwmon: (peci/cputemp) Fix off-by-one in coretemp_label allocation
hwmon: (nct6775) Fix incorrect parenthesization in nct6775_write_fan_div()
ARM: dts: qcom: sdx65: Add Qcom SMMU-500 as the fallback for IOMMU node
ARM: dts: qcom: sdx55: Add Qcom SMMU-500 as the fallback for IOMMU node
ARM: dts: exynos: correct TMU phandle in Exynos4210
ARM: dts: exynos: correct TMU phandle in Exynos4
ARM: dts: exynos: correct TMU phandle in Odroid XU3 family
ARM: dts: exynos: correct TMU phandle in Exynos5250
ARM: dts: exynos: correct TMU phandle in Odroid XU
ARM: dts: exynos: correct TMU phandle in Odroid HC1
arm64: mm: hugetlb: Disable HUGETLB_PAGE_OPTIMIZE_VMEMMAP
fuse: add inode/permission checks to fileattr_get/fileattr_set
rbd: avoid use-after-free in do_rbd_add() when rbd_dev_create() fails
ceph: update the time stamps and try to drop the suid/sgid
regulator: core: Use ktime_get_boottime() to determine how long a regulator was off
panic: fix the panic_print NMI backtrace setting
mm/hwpoison: convert TTU_IGNORE_HWPOISON to TTU_HWPOISON
alpha: fix FEN fault handling
dax/kmem: Fix leak of memory-hotplug resources
mips: fix syscall_get_nr
media: ipu3-cio2: Fix PM runtime usage_count in driver unbind
remoteproc/mtk_scp: Move clk ops outside send_lock
docs: gdbmacros: print newest record
mm: memcontrol: deprecate charge moving
mm/thp: check and bail out if page in deferred queue already
ktest.pl: Give back console on Ctrt^C on monitor
kprobes: Fix to handle forcibly unoptimized kprobes on freeing_list
ktest.pl: Fix missing "end_monitor" when machine check fails
ktest.pl: Add RUN_TIMEOUT option with default unlimited
memory tier: release the new_memtier in find_create_memory_tier()
ring-buffer: Handle race between rb_move_tail and rb_check_pages
tools/bootconfig: fix single & used for logical condition
tracing/eprobe: Fix to add filter on eprobe description in README file
iommu/amd: Add a length limitation for the ivrs_acpihid command-line parameter
iommu/amd: Improve page fault error reporting
scsi: aacraid: Allocate cmd_priv with scsicmd
scsi: qla2xxx: Fix link failure in NPIV environment
scsi: qla2xxx: Check if port is online before sending ELS
scsi: qla2xxx: Fix DMA-API call trace on NVMe LS requests
scsi: qla2xxx: Remove unintended flag clearing
scsi: qla2xxx: Fix erroneous link down
scsi: qla2xxx: Remove increment of interface err cnt
scsi: ses: Don't attach if enclosure has no components
scsi: ses: Fix slab-out-of-bounds in ses_enclosure_data_process()
scsi: ses: Fix possible addl_desc_ptr out-of-bounds accesses
scsi: ses: Fix possible desc_ptr out-of-bounds accesses
scsi: ses: Fix slab-out-of-bounds in ses_intf_remove()
RISC-V: add a spin_shadow_stack declaration
riscv: Avoid enabling interrupts in die()
riscv: mm: fix regression due to update_mmu_cache change
riscv: jump_label: Fixup unaligned arch_static_branch function
riscv, mm: Perform BPF exhandler fixup on page fault
riscv: ftrace: Remove wasted nops for !RISCV_ISA_C
riscv: ftrace: Reduce the detour code size to half
MIPS: DTS: CI20: fix otg power gpio
PCI/PM: Observe reset delay irrespective of bridge_d3
PCI: Unify delay handling for reset and resume
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: Avoid FLR for AMD FCH AHCI adapters
PCI/DPC: Await readiness of secondary bus after reset
bus: mhi: ep: Only send -ENOTCONN status if client driver is available
bus: mhi: ep: Move chan->lock to the start of processing queued ch ring
bus: mhi: ep: Save channel state locally during suspend and resume
iommu/vt-d: Avoid superfluous IOTLB tracking in lazy mode
iommu/vt-d: Fix PASID directory pointer coherency
vfio/type1: exclude mdevs from VFIO_UPDATE_VADDR
vfio/type1: prevent underflow of locked_vm via exec()
vfio/type1: track locked_vm per dma
vfio/type1: restore locked_vm
drm/amd: Fix initialization for nbio 7.5.1
drm/i915/quirks: Add inverted backlight quirk for HP 14-r206nv
drm/radeon: Fix eDP for single-display iMac11,2
drm/i915: Don't use stolen memory for ring buffers with LLC
drm/i915: Don't use BAR mappings for ring buffers with LLC
drm/gud: Fix UBSAN warning
drm/edid: fix AVI infoframe aspect ratio handling
drm/edid: fix parsing of 3D modes from HDMI VSDB
qede: avoid uninitialized entries in coal_entry array
brd: use radix_tree_maybe_preload instead of radix_tree_preload
sbitmap: Advance the queue index before waking up a queue
wait: Return number of exclusive waiters awaken
sbitmap: Try each queue to wake up at least one waiter
kbuild: Port silent mode detection to future gnu make.
net: avoid double iput when sock_alloc_file fails
Linux 6.1.16
Change-Id: I705caf70ee547e6d55f38d133bdcd50713aed745
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This commit is contained in:
Greg Kroah-Hartman
commit
2cb73a87e4
@ -86,6 +86,8 @@ Brief summary of control files.
|
||||
memory.swappiness set/show swappiness parameter of vmscan
|
||||
(See sysctl's vm.swappiness)
|
||||
memory.move_charge_at_immigrate set/show controls of moving charges
|
||||
This knob is deprecated and shouldn't be
|
||||
used.
|
||||
memory.oom_control set/show oom controls.
|
||||
memory.numa_stat show the number of memory usage per numa
|
||||
node
|
||||
@ -716,8 +718,15 @@ NOTE2:
|
||||
It is recommended to set the soft limit always below the hard limit,
|
||||
otherwise the hard limit will take precedence.
|
||||
|
||||
8. Move charges at task migration
|
||||
=================================
|
||||
8. Move charges at task migration (DEPRECATED!)
|
||||
===============================================
|
||||
|
||||
THIS IS DEPRECATED!
|
||||
|
||||
It's expensive and unreliable! It's better practice to launch workload
|
||||
tasks directly from inside their target cgroup. Use dedicated workload
|
||||
cgroups to allow fine-grained policy adjustments without having to
|
||||
move physical pages between control domains.
|
||||
|
||||
Users can move charges associated with a task along with task migration, that
|
||||
is, uncharge task's pages from the old cgroup and charge them to the new cgroup.
|
||||
|
||||
@ -479,8 +479,16 @@ Spectre variant 2
|
||||
On Intel Skylake-era systems the mitigation covers most, but not all,
|
||||
cases. See :ref:`[3] <spec_ref3>` for more details.
|
||||
|
||||
On CPUs with hardware mitigation for Spectre variant 2 (e.g. Enhanced
|
||||
IBRS on x86), retpoline is automatically disabled at run time.
|
||||
On CPUs with hardware mitigation for Spectre variant 2 (e.g. IBRS
|
||||
or enhanced IBRS on x86), retpoline is automatically disabled at run time.
|
||||
|
||||
Systems which support enhanced IBRS (eIBRS) enable IBRS protection once at
|
||||
boot, by setting the IBRS bit, and they're automatically protected against
|
||||
Spectre v2 variant attacks, including cross-thread branch target injections
|
||||
on SMT systems (STIBP). In other words, eIBRS enables STIBP too.
|
||||
|
||||
Legacy IBRS systems clear the IBRS bit on exit to userspace and
|
||||
therefore explicitly enable STIBP for that
|
||||
|
||||
The retpoline mitigation is turned on by default on vulnerable
|
||||
CPUs. It can be forced on or off by the administrator
|
||||
@ -504,9 +512,12 @@ Spectre variant 2
|
||||
For Spectre variant 2 mitigation, individual user programs
|
||||
can be compiled with return trampolines for indirect branches.
|
||||
This protects them from consuming poisoned entries in the branch
|
||||
target buffer left by malicious software. Alternatively, the
|
||||
programs can disable their indirect branch speculation via prctl()
|
||||
(See :ref:`Documentation/userspace-api/spec_ctrl.rst <set_spec_ctrl>`).
|
||||
target buffer left by malicious software.
|
||||
|
||||
On legacy IBRS systems, at return to userspace, implicit STIBP is disabled
|
||||
because the kernel clears the IBRS bit. In this case, the userspace programs
|
||||
can disable indirect branch speculation via prctl() (See
|
||||
:ref:`Documentation/userspace-api/spec_ctrl.rst <set_spec_ctrl>`).
|
||||
On x86, this will turn on STIBP to guard against attacks from the
|
||||
sibling thread when the user program is running, and use IBPB to
|
||||
flush the branch target buffer when switching to/from the program.
|
||||
|
||||
@ -312,10 +312,10 @@ define dmesg
|
||||
set var $prev_flags = $info->flags
|
||||
end
|
||||
|
||||
set var $id = ($id + 1) & $id_mask
|
||||
if ($id == $end_id)
|
||||
loop_break
|
||||
end
|
||||
set var $id = ($id + 1) & $id_mask
|
||||
end
|
||||
end
|
||||
document dmesg
|
||||
|
||||
@ -99,19 +99,26 @@ code value description
|
||||
BPF_ADD 0x00 dst += src
|
||||
BPF_SUB 0x10 dst -= src
|
||||
BPF_MUL 0x20 dst \*= src
|
||||
BPF_DIV 0x30 dst /= src
|
||||
BPF_DIV 0x30 dst = (src != 0) ? (dst / src) : 0
|
||||
BPF_OR 0x40 dst \|= src
|
||||
BPF_AND 0x50 dst &= src
|
||||
BPF_LSH 0x60 dst <<= src
|
||||
BPF_RSH 0x70 dst >>= src
|
||||
BPF_NEG 0x80 dst = ~src
|
||||
BPF_MOD 0x90 dst %= src
|
||||
BPF_MOD 0x90 dst = (src != 0) ? (dst % src) : dst
|
||||
BPF_XOR 0xa0 dst ^= src
|
||||
BPF_MOV 0xb0 dst = src
|
||||
BPF_ARSH 0xc0 sign extending shift right
|
||||
BPF_END 0xd0 byte swap operations (see `Byte swap instructions`_ below)
|
||||
======== ===== ==========================================================
|
||||
|
||||
Underflow and overflow are allowed during arithmetic operations, meaning
|
||||
the 64-bit or 32-bit value will wrap. If eBPF program execution would
|
||||
result in division by zero, the destination register is instead set to zero.
|
||||
If execution would result in modulo by zero, for ``BPF_ALU64`` the value of
|
||||
the destination register is unchanged whereas for ``BPF_ALU`` the upper
|
||||
32 bits of the destination register are zeroed.
|
||||
|
||||
``BPF_ADD | BPF_X | BPF_ALU`` means::
|
||||
|
||||
dst_reg = (u32) dst_reg + (u32) src_reg;
|
||||
@ -128,6 +135,11 @@ BPF_END 0xd0 byte swap operations (see `Byte swap instructions`_ below)
|
||||
|
||||
src_reg = src_reg ^ imm32
|
||||
|
||||
Also note that the division and modulo operations are unsigned. Thus, for
|
||||
``BPF_ALU``, 'imm' is first interpreted as an unsigned 32-bit value, whereas
|
||||
for ``BPF_ALU64``, 'imm' is first sign extended to 64 bits and the result
|
||||
interpreted as an unsigned 64-bit value. There are no instructions for
|
||||
signed division or modulo.
|
||||
|
||||
Byte swap instructions
|
||||
~~~~~~~~~~~~~~~~~~~~~~
|
||||
|
||||
@ -39,6 +39,10 @@ Setup
|
||||
this mode. In this case, you should build the kernel with
|
||||
CONFIG_RANDOMIZE_BASE disabled if the architecture supports KASLR.
|
||||
|
||||
- Build the gdb scripts (required on kernels v5.1 and above)::
|
||||
|
||||
make scripts_gdb
|
||||
|
||||
- Enable the gdb stub of QEMU/KVM, either
|
||||
|
||||
- at VM startup time by appending "-s" to the QEMU command line
|
||||
|
||||
@ -32,7 +32,7 @@ properties:
|
||||
- items:
|
||||
- enum:
|
||||
- mediatek,mt8186-disp-ccorr
|
||||
- const: mediatek,mt8183-disp-ccorr
|
||||
- const: mediatek,mt8192-disp-ccorr
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
@ -62,7 +62,7 @@ patternProperties:
|
||||
description: phandle of the CPU DAI
|
||||
|
||||
patternProperties:
|
||||
"^codec-[0-9]+$":
|
||||
"^codec(-[0-9]+)?$":
|
||||
type: object
|
||||
additionalProperties: false
|
||||
description: |-
|
||||
|
||||
@ -22,6 +22,10 @@ enhancements. It can monitor up to 4 voltages, 16 temperatures and
|
||||
8 fans. It also contains an integrated watchdog which is currently
|
||||
implemented in this driver.
|
||||
|
||||
The 4 voltages require a board-specific multiplier, since the BMC can
|
||||
only measure voltages up to 3.3V and thus relies on voltage dividers.
|
||||
Consult your motherboard manual for details.
|
||||
|
||||
To clear a temperature or fan alarm, execute the following command with the
|
||||
correct path to the alarm file::
|
||||
|
||||
|
||||
@ -4483,6 +4483,18 @@ not holding a previously reported uncorrected error).
|
||||
:Parameters: struct kvm_s390_cmma_log (in, out)
|
||||
:Returns: 0 on success, a negative value on error
|
||||
|
||||
Errors:
|
||||
|
||||
====== =============================================================
|
||||
ENOMEM not enough memory can be allocated to complete the task
|
||||
ENXIO if CMMA is not enabled
|
||||
EINVAL if KVM_S390_CMMA_PEEK is not set but migration mode was not enabled
|
||||
EINVAL if KVM_S390_CMMA_PEEK is not set but dirty tracking has been
|
||||
disabled (and thus migration mode was automatically disabled)
|
||||
EFAULT if the userspace address is invalid or if no page table is
|
||||
present for the addresses (e.g. when using hugepages).
|
||||
====== =============================================================
|
||||
|
||||
This ioctl is used to get the values of the CMMA bits on the s390
|
||||
architecture. It is meant to be used in two scenarios:
|
||||
|
||||
@ -4563,12 +4575,6 @@ mask is unused.
|
||||
|
||||
values points to the userspace buffer where the result will be stored.
|
||||
|
||||
This ioctl can fail with -ENOMEM if not enough memory can be allocated to
|
||||
complete the task, with -ENXIO if CMMA is not enabled, with -EINVAL if
|
||||
KVM_S390_CMMA_PEEK is not set but migration mode was not enabled, with
|
||||
-EFAULT if the userspace address is invalid or if no page table is
|
||||
present for the addresses (e.g. when using hugepages).
|
||||
|
||||
4.108 KVM_S390_SET_CMMA_BITS
|
||||
----------------------------
|
||||
|
||||
|
||||
@ -302,6 +302,10 @@ Allows userspace to start migration mode, needed for PGSTE migration.
|
||||
Setting this attribute when migration mode is already active will have
|
||||
no effects.
|
||||
|
||||
Dirty tracking must be enabled on all memslots, else -EINVAL is returned. When
|
||||
dirty tracking is disabled on any memslot, migration mode is automatically
|
||||
stopped.
|
||||
|
||||
:Parameters: none
|
||||
:Returns: -ENOMEM if there is not enough free memory to start migration mode;
|
||||
-EINVAL if the state of the VM is invalid (e.g. no memory defined);
|
||||
|
||||
15
Makefile
15
Makefile
@ -1,7 +1,7 @@
|
||||
# SPDX-License-Identifier: GPL-2.0
|
||||
VERSION = 6
|
||||
PATCHLEVEL = 1
|
||||
SUBLEVEL = 15
|
||||
SUBLEVEL = 16
|
||||
EXTRAVERSION =
|
||||
NAME = Hurr durr I'ma ninja sloth
|
||||
|
||||
@ -93,10 +93,17 @@ endif
|
||||
|
||||
# If the user is running make -s (silent mode), suppress echoing of
|
||||
# commands
|
||||
# make-4.0 (and later) keep single letter options in the 1st word of MAKEFLAGS.
|
||||
|
||||
ifneq ($(findstring s,$(filter-out --%,$(MAKEFLAGS))),)
|
||||
quiet=silent_
|
||||
KBUILD_VERBOSE = 0
|
||||
ifeq ($(filter 3.%,$(MAKE_VERSION)),)
|
||||
silence:=$(findstring s,$(firstword -$(MAKEFLAGS)))
|
||||
else
|
||||
silence:=$(findstring s,$(filter-out --%,$(MAKEFLAGS)))
|
||||
endif
|
||||
|
||||
ifeq ($(silence),s)
|
||||
quiet=silent_
|
||||
KBUILD_VERBOSE = 0
|
||||
endif
|
||||
|
||||
export quiet Q KBUILD_VERBOSE
|
||||
|
||||
@ -148,7 +148,7 @@ main (int argc, char *argv[])
|
||||
#ifdef __ELF__
|
||||
elf = (struct elfhdr *) buf;
|
||||
|
||||
if (elf->e_ident[0] == 0x7f && str_has_prefix((char *)elf->e_ident + 1, "ELF")) {
|
||||
if (memcmp(&elf->e_ident[EI_MAG0], ELFMAG, SELFMAG) == 0) {
|
||||
if (elf->e_type != ET_EXEC) {
|
||||
fprintf(stderr, "%s: %s is not an ELF executable\n",
|
||||
prog_name, inname);
|
||||
|
||||
@ -233,7 +233,21 @@ do_entIF(unsigned long type, struct pt_regs *regs)
|
||||
{
|
||||
int signo, code;
|
||||
|
||||
if ((regs->ps & ~IPL_MAX) == 0) {
|
||||
if (type == 3) { /* FEN fault */
|
||||
/* Irritating users can call PAL_clrfen to disable the
|
||||
FPU for the process. The kernel will then trap in
|
||||
do_switch_stack and undo_switch_stack when we try
|
||||
to save and restore the FP registers.
|
||||
|
||||
Given that GCC by default generates code that uses the
|
||||
FP registers, PAL_clrfen is not useful except for DoS
|
||||
attacks. So turn the bleeding FPU back on and be done
|
||||
with it. */
|
||||
current_thread_info()->pcb.flags |= 1;
|
||||
__reload_thread(¤t_thread_info()->pcb);
|
||||
return;
|
||||
}
|
||||
if (!user_mode(regs)) {
|
||||
if (type == 1) {
|
||||
const unsigned int *data
|
||||
= (const unsigned int *) regs->pc;
|
||||
@ -366,20 +380,6 @@ do_entIF(unsigned long type, struct pt_regs *regs)
|
||||
}
|
||||
break;
|
||||
|
||||
case 3: /* FEN fault */
|
||||
/* Irritating users can call PAL_clrfen to disable the
|
||||
FPU for the process. The kernel will then trap in
|
||||
do_switch_stack and undo_switch_stack when we try
|
||||
to save and restore the FP registers.
|
||||
|
||||
Given that GCC by default generates code that uses the
|
||||
FP registers, PAL_clrfen is not useful except for DoS
|
||||
attacks. So turn the bleeding FPU back on and be done
|
||||
with it. */
|
||||
current_thread_info()->pcb.flags |= 1;
|
||||
__reload_thread(¤t_thread_info()->pcb);
|
||||
return;
|
||||
|
||||
case 5: /* illoc */
|
||||
default: /* unexpected instruction-fault type */
|
||||
;
|
||||
|
||||
@ -250,7 +250,7 @@ &fimd {
|
||||
i80-if-timings {
|
||||
cs-setup = <0>;
|
||||
wr-setup = <0>;
|
||||
wr-act = <1>;
|
||||
wr-active = <1>;
|
||||
wr-hold = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -10,7 +10,7 @@
|
||||
/ {
|
||||
thermal-zones {
|
||||
cpu_thermal: cpu-thermal {
|
||||
thermal-sensors = <&tmu 0>;
|
||||
thermal-sensors = <&tmu>;
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
trips {
|
||||
|
||||
@ -605,7 +605,7 @@ i2c_8: i2c@138e0000 {
|
||||
status = "disabled";
|
||||
|
||||
hdmi_i2c_phy: hdmiphy@38 {
|
||||
compatible = "exynos4210-hdmiphy";
|
||||
compatible = "samsung,exynos4210-hdmiphy";
|
||||
reg = <0x38>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -393,7 +393,6 @@ &cpu_alert2 {
|
||||
&cpu_thermal {
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
thermal-sensors = <&tmu 0>;
|
||||
};
|
||||
|
||||
&gic {
|
||||
|
||||
@ -1107,7 +1107,7 @@ timer {
|
||||
&cpu_thermal {
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
thermal-sensors = <&tmu 0>;
|
||||
thermal-sensors = <&tmu>;
|
||||
|
||||
cooling-maps {
|
||||
map0 {
|
||||
|
||||
@ -120,7 +120,6 @@ &clock_audss {
|
||||
};
|
||||
|
||||
&cpu0_thermal {
|
||||
thermal-sensors = <&tmu_cpu0 0>;
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
|
||||
|
||||
@ -592,7 +592,7 @@ dp_phy: dp-video-phy {
|
||||
};
|
||||
|
||||
mipi_phy: mipi-video-phy {
|
||||
compatible = "samsung,s5pv210-mipi-video-phy";
|
||||
compatible = "samsung,exynos5420-mipi-video-phy";
|
||||
syscon = <&pmu_system_controller>;
|
||||
#phy-cells = <1>;
|
||||
};
|
||||
|
||||
@ -31,7 +31,7 @@ led-1 {
|
||||
|
||||
thermal-zones {
|
||||
cpu0_thermal: cpu0-thermal {
|
||||
thermal-sensors = <&tmu_cpu0 0>;
|
||||
thermal-sensors = <&tmu_cpu0>;
|
||||
trips {
|
||||
cpu0_alert0: cpu-alert-0 {
|
||||
temperature = <70000>; /* millicelsius */
|
||||
@ -86,7 +86,7 @@ map1 {
|
||||
};
|
||||
};
|
||||
cpu1_thermal: cpu1-thermal {
|
||||
thermal-sensors = <&tmu_cpu1 0>;
|
||||
thermal-sensors = <&tmu_cpu1>;
|
||||
trips {
|
||||
cpu1_alert0: cpu-alert-0 {
|
||||
temperature = <70000>;
|
||||
@ -130,7 +130,7 @@ map1 {
|
||||
};
|
||||
};
|
||||
cpu2_thermal: cpu2-thermal {
|
||||
thermal-sensors = <&tmu_cpu2 0>;
|
||||
thermal-sensors = <&tmu_cpu2>;
|
||||
trips {
|
||||
cpu2_alert0: cpu-alert-0 {
|
||||
temperature = <70000>;
|
||||
@ -174,7 +174,7 @@ map1 {
|
||||
};
|
||||
};
|
||||
cpu3_thermal: cpu3-thermal {
|
||||
thermal-sensors = <&tmu_cpu3 0>;
|
||||
thermal-sensors = <&tmu_cpu3>;
|
||||
trips {
|
||||
cpu3_alert0: cpu-alert-0 {
|
||||
temperature = <70000>;
|
||||
@ -218,7 +218,7 @@ map1 {
|
||||
};
|
||||
};
|
||||
gpu_thermal: gpu-thermal {
|
||||
thermal-sensors = <&tmu_gpu 0>;
|
||||
thermal-sensors = <&tmu_gpu>;
|
||||
trips {
|
||||
gpu_alert0: gpu-alert-0 {
|
||||
temperature = <70000>;
|
||||
|
||||
@ -50,7 +50,7 @@ fan0: pwm-fan {
|
||||
|
||||
thermal-zones {
|
||||
cpu0_thermal: cpu0-thermal {
|
||||
thermal-sensors = <&tmu_cpu0 0>;
|
||||
thermal-sensors = <&tmu_cpu0>;
|
||||
polling-delay-passive = <250>;
|
||||
polling-delay = <0>;
|
||||
trips {
|
||||
@ -139,7 +139,7 @@ cpu0_cooling_map4: map4 {
|
||||
};
|
||||
};
|
||||
cpu1_thermal: cpu1-thermal {
|
||||
thermal-sensors = <&tmu_cpu1 0>;
|
||||
thermal-sensors = <&tmu_cpu1>;
|
||||
polling-delay-passive = <250>;
|
||||
polling-delay = <0>;
|
||||
trips {
|
||||
@ -212,7 +212,7 @@ cpu1_cooling_map4: map4 {
|
||||
};
|
||||
};
|
||||
cpu2_thermal: cpu2-thermal {
|
||||
thermal-sensors = <&tmu_cpu2 0>;
|
||||
thermal-sensors = <&tmu_cpu2>;
|
||||
polling-delay-passive = <250>;
|
||||
polling-delay = <0>;
|
||||
trips {
|
||||
@ -285,7 +285,7 @@ cpu2_cooling_map4: map4 {
|
||||
};
|
||||
};
|
||||
cpu3_thermal: cpu3-thermal {
|
||||
thermal-sensors = <&tmu_cpu3 0>;
|
||||
thermal-sensors = <&tmu_cpu3>;
|
||||
polling-delay-passive = <250>;
|
||||
polling-delay = <0>;
|
||||
trips {
|
||||
@ -358,7 +358,7 @@ cpu3_cooling_map4: map4 {
|
||||
};
|
||||
};
|
||||
gpu_thermal: gpu-thermal {
|
||||
thermal-sensors = <&tmu_gpu 0>;
|
||||
thermal-sensors = <&tmu_gpu>;
|
||||
polling-delay-passive = <250>;
|
||||
polling-delay = <0>;
|
||||
trips {
|
||||
|
||||
@ -513,7 +513,7 @@ gpr: iomuxc-gpr@30340000 {
|
||||
|
||||
mux: mux-controller {
|
||||
compatible = "mmio-mux";
|
||||
#mux-control-cells = <0>;
|
||||
#mux-control-cells = <1>;
|
||||
mux-reg-masks = <0x14 0x00000010>;
|
||||
};
|
||||
|
||||
|
||||
@ -577,7 +577,7 @@ pil-reloc@94c {
|
||||
};
|
||||
|
||||
apps_smmu: iommu@15000000 {
|
||||
compatible = "qcom,sdx55-smmu-500", "arm,mmu-500";
|
||||
compatible = "qcom,sdx55-smmu-500", "qcom,smmu-500", "arm,mmu-500";
|
||||
reg = <0x15000000 0x20000>;
|
||||
#iommu-cells = <2>;
|
||||
#global-interrupts = <1>;
|
||||
|
||||
@ -455,7 +455,7 @@ pil-reloc@94c {
|
||||
};
|
||||
|
||||
apps_smmu: iommu@15000000 {
|
||||
compatible = "qcom,sdx65-smmu-500", "arm,mmu-500";
|
||||
compatible = "qcom,sdx65-smmu-500", "qcom,smmu-500", "arm,mmu-500";
|
||||
reg = <0x15000000 0x40000>;
|
||||
#iommu-cells = <2>;
|
||||
#global-interrupts = <1>;
|
||||
|
||||
@ -405,6 +405,7 @@ bsec: efuse@5c005000 {
|
||||
|
||||
part_number_otp: part_number_otp@4 {
|
||||
reg = <0x4 0x2>;
|
||||
bits = <0 12>;
|
||||
};
|
||||
ts_cal1: calib@5c {
|
||||
reg = <0x5c 0x2>;
|
||||
|
||||
@ -57,7 +57,7 @@ reg_vdd_cpux: vdd-cpux-regulator {
|
||||
regulator-ramp-delay = <50>; /* 4ms */
|
||||
|
||||
enable-active-high;
|
||||
enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
|
||||
enable-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
|
||||
gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
|
||||
gpios-states = <0x1>;
|
||||
states = <1100000 0>, <1300000 1>;
|
||||
|
||||
@ -107,6 +107,7 @@ CONFIG_MEDIA_CAMERA_SUPPORT=y
|
||||
CONFIG_DRM=y
|
||||
CONFIG_DRM_V3D=y
|
||||
CONFIG_DRM_VC4=y
|
||||
CONFIG_FB=y
|
||||
CONFIG_FB_SIMPLE=y
|
||||
CONFIG_FRAMEBUFFER_CONSOLE=y
|
||||
CONFIG_SOUND=y
|
||||
|
||||
@ -99,6 +99,7 @@ struct mmdc_pmu {
|
||||
cpumask_t cpu;
|
||||
struct hrtimer hrtimer;
|
||||
unsigned int active_events;
|
||||
int id;
|
||||
struct device *dev;
|
||||
struct perf_event *mmdc_events[MMDC_NUM_COUNTERS];
|
||||
struct hlist_node node;
|
||||
@ -433,8 +434,6 @@ static enum hrtimer_restart mmdc_pmu_timer_handler(struct hrtimer *hrtimer)
|
||||
static int mmdc_pmu_init(struct mmdc_pmu *pmu_mmdc,
|
||||
void __iomem *mmdc_base, struct device *dev)
|
||||
{
|
||||
int mmdc_num;
|
||||
|
||||
*pmu_mmdc = (struct mmdc_pmu) {
|
||||
.pmu = (struct pmu) {
|
||||
.task_ctx_nr = perf_invalid_context,
|
||||
@ -452,15 +451,16 @@ static int mmdc_pmu_init(struct mmdc_pmu *pmu_mmdc,
|
||||
.active_events = 0,
|
||||
};
|
||||
|
||||
mmdc_num = ida_simple_get(&mmdc_ida, 0, 0, GFP_KERNEL);
|
||||
pmu_mmdc->id = ida_simple_get(&mmdc_ida, 0, 0, GFP_KERNEL);
|
||||
|
||||
return mmdc_num;
|
||||
return pmu_mmdc->id;
|
||||
}
|
||||
|
||||
static int imx_mmdc_remove(struct platform_device *pdev)
|
||||
{
|
||||
struct mmdc_pmu *pmu_mmdc = platform_get_drvdata(pdev);
|
||||
|
||||
ida_simple_remove(&mmdc_ida, pmu_mmdc->id);
|
||||
cpuhp_state_remove_instance_nocalls(cpuhp_mmdc_state, &pmu_mmdc->node);
|
||||
perf_pmu_unregister(&pmu_mmdc->pmu);
|
||||
iounmap(pmu_mmdc->mmdc_base);
|
||||
@ -474,7 +474,6 @@ static int imx_mmdc_perf_init(struct platform_device *pdev, void __iomem *mmdc_b
|
||||
{
|
||||
struct mmdc_pmu *pmu_mmdc;
|
||||
char *name;
|
||||
int mmdc_num;
|
||||
int ret;
|
||||
const struct of_device_id *of_id =
|
||||
of_match_device(imx_mmdc_dt_ids, &pdev->dev);
|
||||
@ -497,14 +496,14 @@ static int imx_mmdc_perf_init(struct platform_device *pdev, void __iomem *mmdc_b
|
||||
cpuhp_mmdc_state = ret;
|
||||
}
|
||||
|
||||
mmdc_num = mmdc_pmu_init(pmu_mmdc, mmdc_base, &pdev->dev);
|
||||
pmu_mmdc->mmdc_ipg_clk = mmdc_ipg_clk;
|
||||
if (mmdc_num == 0)
|
||||
name = "mmdc";
|
||||
else
|
||||
name = devm_kasprintf(&pdev->dev,
|
||||
GFP_KERNEL, "mmdc%d", mmdc_num);
|
||||
ret = mmdc_pmu_init(pmu_mmdc, mmdc_base, &pdev->dev);
|
||||
if (ret < 0)
|
||||
goto pmu_free;
|
||||
|
||||
name = devm_kasprintf(&pdev->dev,
|
||||
GFP_KERNEL, "mmdc%d", ret);
|
||||
|
||||
pmu_mmdc->mmdc_ipg_clk = mmdc_ipg_clk;
|
||||
pmu_mmdc->devtype_data = (struct fsl_mmdc_devtype_data *)of_id->data;
|
||||
|
||||
hrtimer_init(&pmu_mmdc->hrtimer, CLOCK_MONOTONIC,
|
||||
@ -525,6 +524,7 @@ static int imx_mmdc_perf_init(struct platform_device *pdev, void __iomem *mmdc_b
|
||||
|
||||
pmu_register_err:
|
||||
pr_warn("MMDC Perf PMU failed (%d), disabled\n", ret);
|
||||
ida_simple_remove(&mmdc_ida, pmu_mmdc->id);
|
||||
cpuhp_state_remove_instance_nocalls(cpuhp_mmdc_state, &pmu_mmdc->node);
|
||||
hrtimer_cancel(&pmu_mmdc->hrtimer);
|
||||
pmu_free:
|
||||
|
||||
@ -158,7 +158,7 @@ static int __init omap1_dm_timer_init(void)
|
||||
kfree(pdata);
|
||||
|
||||
err_free_pdev:
|
||||
platform_device_unregister(pdev);
|
||||
platform_device_put(pdev);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
@ -140,6 +140,7 @@ static int __init omap4_sram_init(void)
|
||||
__func__);
|
||||
else
|
||||
sram_sync = (void __iomem *)gen_pool_alloc(sram_pool, PAGE_SIZE);
|
||||
of_node_put(np);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
@ -76,6 +76,7 @@ static void __init realtime_counter_init(void)
|
||||
}
|
||||
|
||||
rate = clk_get_rate(sys_clk);
|
||||
clk_put(sys_clk);
|
||||
|
||||
if (soc_is_dra7xx()) {
|
||||
/*
|
||||
|
||||
@ -173,7 +173,8 @@ static struct samsung_pwm_variant s3c64xx_pwm_variant = {
|
||||
.tclk_mask = (1 << 7) | (1 << 6) | (1 << 5),
|
||||
};
|
||||
|
||||
void __init s3c64xx_set_timer_source(unsigned int event, unsigned int source)
|
||||
void __init s3c64xx_set_timer_source(enum s3c64xx_timer_mode event,
|
||||
enum s3c64xx_timer_mode source)
|
||||
{
|
||||
s3c64xx_pwm_variant.output_mask = BIT(SAMSUNG_PWM_NUM) - 1;
|
||||
s3c64xx_pwm_variant.output_mask &= ~(BIT(event) | BIT(source));
|
||||
|
||||
@ -213,6 +213,7 @@ int __init zynq_early_slcr_init(void)
|
||||
zynq_slcr_regmap = syscon_regmap_lookup_by_compatible("xlnx,zynq-slcr");
|
||||
if (IS_ERR(zynq_slcr_regmap)) {
|
||||
pr_err("%s: failed to find zynq-slcr\n", __func__);
|
||||
of_node_put(np);
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
|
||||
@ -101,7 +101,6 @@ config ARM64
|
||||
select ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT
|
||||
select ARCH_WANT_FRAME_POINTERS
|
||||
select ARCH_WANT_HUGE_PMD_SHARE if ARM64_4K_PAGES || (ARM64_16K_PAGES && !ARM64_VA_BITS_36)
|
||||
select ARCH_WANT_HUGETLB_PAGE_OPTIMIZE_VMEMMAP
|
||||
select ARCH_WANT_LD_ORPHAN_WARN
|
||||
select ARCH_WANTS_NO_INSTR
|
||||
select ARCH_WANTS_THP_SWAP if ARM64_4K_PAGES
|
||||
|
||||
@ -168,15 +168,15 @@ sn: sn@32 {
|
||||
reg = <0x32 0x20>;
|
||||
};
|
||||
|
||||
eth_mac: eth_mac@0 {
|
||||
eth_mac: eth-mac@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
|
||||
bt_mac: bt_mac@6 {
|
||||
bt_mac: bt-mac@6 {
|
||||
reg = <0x6 0x6>;
|
||||
};
|
||||
|
||||
wifi_mac: wifi_mac@c {
|
||||
wifi_mac: wifi-mac@c {
|
||||
reg = <0xc 0x6>;
|
||||
};
|
||||
|
||||
@ -217,7 +217,7 @@ &i2c1 {
|
||||
pinctrl-names = "default";
|
||||
|
||||
/* RTC */
|
||||
pcf8563: pcf8563@51 {
|
||||
pcf8563: rtc@51 {
|
||||
compatible = "nxp,pcf8563";
|
||||
reg = <0x51>;
|
||||
status = "okay";
|
||||
@ -303,7 +303,7 @@ &uart_AO_B {
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
phy-supply = <&usb_pwr>;
|
||||
vbus-supply = <&usb_pwr>;
|
||||
};
|
||||
|
||||
&spicc1 {
|
||||
|
||||
@ -152,7 +152,7 @@ scpi {
|
||||
scpi_clocks: clocks {
|
||||
compatible = "arm,scpi-clocks";
|
||||
|
||||
scpi_dvfs: clock-controller {
|
||||
scpi_dvfs: clocks-0 {
|
||||
compatible = "arm,scpi-dvfs-clocks";
|
||||
#clock-cells = <1>;
|
||||
clock-indices = <0>;
|
||||
@ -161,7 +161,7 @@ scpi_dvfs: clock-controller {
|
||||
};
|
||||
|
||||
scpi_sensors: sensors {
|
||||
compatible = "amlogic,meson-gxbb-scpi-sensors";
|
||||
compatible = "amlogic,meson-gxbb-scpi-sensors", "arm,scpi-sensors";
|
||||
#thermal-sensor-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -1694,7 +1694,7 @@ int_mdio: mdio@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
internal_ephy: ethernet_phy@8 {
|
||||
internal_ephy: ethernet-phy@8 {
|
||||
compatible = "ethernet-phy-id0180.3301",
|
||||
"ethernet-phy-ieee802.3-c22";
|
||||
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
@ -401,5 +401,4 @@ &uart_AO {
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
dr_mode = "host";
|
||||
};
|
||||
|
||||
@ -57,26 +57,6 @@ cpu_opp_table: opp-table {
|
||||
compatible = "operating-points-v2";
|
||||
opp-shared;
|
||||
|
||||
opp-100000000 {
|
||||
opp-hz = /bits/ 64 <100000000>;
|
||||
opp-microvolt = <731000>;
|
||||
};
|
||||
|
||||
opp-250000000 {
|
||||
opp-hz = /bits/ 64 <250000000>;
|
||||
opp-microvolt = <731000>;
|
||||
};
|
||||
|
||||
opp-500000000 {
|
||||
opp-hz = /bits/ 64 <500000000>;
|
||||
opp-microvolt = <731000>;
|
||||
};
|
||||
|
||||
opp-667000000 {
|
||||
opp-hz = /bits/ 64 <666666666>;
|
||||
opp-microvolt = <731000>;
|
||||
};
|
||||
|
||||
opp-1000000000 {
|
||||
opp-hz = /bits/ 64 <1000000000>;
|
||||
opp-microvolt = <731000>;
|
||||
|
||||
@ -17,7 +17,7 @@ adc-keys {
|
||||
io-channel-names = "buttons";
|
||||
keyup-threshold-microvolt = <1800000>;
|
||||
|
||||
update-button {
|
||||
button-update {
|
||||
label = "update";
|
||||
linux,code = <KEY_VENDOR>;
|
||||
press-threshold-microvolt = <1300000>;
|
||||
|
||||
@ -232,7 +232,7 @@ sn: sn@14 {
|
||||
reg = <0x14 0x10>;
|
||||
};
|
||||
|
||||
eth_mac: eth_mac@34 {
|
||||
eth_mac: eth-mac@34 {
|
||||
reg = <0x34 0x10>;
|
||||
};
|
||||
|
||||
@ -249,7 +249,7 @@ scpi {
|
||||
scpi_clocks: clocks {
|
||||
compatible = "arm,scpi-clocks";
|
||||
|
||||
scpi_dvfs: scpi_clocks@0 {
|
||||
scpi_dvfs: clocks-0 {
|
||||
compatible = "arm,scpi-dvfs-clocks";
|
||||
#clock-cells = <1>;
|
||||
clock-indices = <0>;
|
||||
@ -531,7 +531,7 @@ periphs: bus@c8834000 {
|
||||
#size-cells = <2>;
|
||||
ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
|
||||
|
||||
hwrng: rng {
|
||||
hwrng: rng@0 {
|
||||
compatible = "amlogic,meson-rng";
|
||||
reg = <0x0 0x0 0x0 0x4>;
|
||||
};
|
||||
|
||||
@ -16,7 +16,7 @@ / {
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
status {
|
||||
led {
|
||||
gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
|
||||
@ -18,7 +18,7 @@ cvbs-connector {
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
status {
|
||||
led {
|
||||
label = "n1:white:status";
|
||||
gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
|
||||
@ -79,6 +79,5 @@ bluetooth {
|
||||
enable-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
|
||||
max-speed = <2000000>;
|
||||
clocks = <&wifi32k>;
|
||||
clock-names = "lpo";
|
||||
};
|
||||
};
|
||||
|
||||
@ -86,11 +86,11 @@ sdio_pwrseq: sdio-pwrseq {
|
||||
};
|
||||
|
||||
&efuse {
|
||||
bt_mac: bt_mac@6 {
|
||||
bt_mac: bt-mac@6 {
|
||||
reg = <0x6 0x6>;
|
||||
};
|
||||
|
||||
wifi_mac: wifi_mac@C {
|
||||
wifi_mac: wifi-mac@c {
|
||||
reg = <0xc 0x6>;
|
||||
};
|
||||
};
|
||||
@ -239,7 +239,7 @@ &i2c_B {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c_b_pins>;
|
||||
|
||||
pcf8563: pcf8563@51 {
|
||||
pcf8563: rtc@51 {
|
||||
compatible = "nxp,pcf8563";
|
||||
reg = <0x51>;
|
||||
status = "okay";
|
||||
|
||||
@ -759,7 +759,7 @@ mux {
|
||||
};
|
||||
};
|
||||
|
||||
eth-phy-mux {
|
||||
eth-phy-mux@55c {
|
||||
compatible = "mdio-mux-mmioreg", "mdio-mux";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
@ -17,13 +17,13 @@ / {
|
||||
compatible = "bananapi,bpi-m5", "amlogic,sm1";
|
||||
model = "Banana Pi BPI-M5";
|
||||
|
||||
adc_keys {
|
||||
adc-keys {
|
||||
compatible = "adc-keys";
|
||||
io-channels = <&saradc 2>;
|
||||
io-channel-names = "buttons";
|
||||
keyup-threshold-microvolt = <1800000>;
|
||||
|
||||
key {
|
||||
button-sw3 {
|
||||
label = "SW3";
|
||||
linux,code = <BTN_3>;
|
||||
press-threshold-microvolt = <1700000>;
|
||||
@ -123,7 +123,7 @@ vddio_c: regulator-vddio_c {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
|
||||
enable-gpio = <&gpio_ao GPIOE_2 GPIO_ACTIVE_HIGH>;
|
||||
enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
|
||||
|
||||
@ -76,9 +76,17 @@ sound {
|
||||
};
|
||||
|
||||
&cpu_thermal {
|
||||
trips {
|
||||
cpu_active: cpu-active {
|
||||
temperature = <60000>; /* millicelsius */
|
||||
hysteresis = <2000>; /* millicelsius */
|
||||
type = "active";
|
||||
};
|
||||
};
|
||||
|
||||
cooling-maps {
|
||||
map {
|
||||
trip = <&cpu_passive>;
|
||||
trip = <&cpu_active>;
|
||||
cooling-device = <&fan0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -562,7 +562,7 @@ ocotp: efuse@30350000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
imx8mm_uid: unique-id@410 {
|
||||
imx8mm_uid: unique-id@4 {
|
||||
reg = <0x4 0x8>;
|
||||
};
|
||||
|
||||
|
||||
@ -563,7 +563,7 @@ ocotp: efuse@30350000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
imx8mn_uid: unique-id@410 {
|
||||
imx8mn_uid: unique-id@4 {
|
||||
reg = <0x4 0x8>;
|
||||
};
|
||||
|
||||
|
||||
@ -424,7 +424,7 @@ ocotp: efuse@30350000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
imx8mp_uid: unique-id@420 {
|
||||
imx8mp_uid: unique-id@8 {
|
||||
reg = <0x8 0x8>;
|
||||
};
|
||||
|
||||
|
||||
@ -592,7 +592,7 @@ ocotp: efuse@30350000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
imx8mq_uid: soc-uid@410 {
|
||||
imx8mq_uid: soc-uid@4 {
|
||||
reg = <0x4 0x8>;
|
||||
};
|
||||
|
||||
|
||||
@ -435,6 +435,7 @@ uart3: serial@11005000 {
|
||||
pwm: pwm@11006000 {
|
||||
compatible = "mediatek,mt7622-pwm";
|
||||
reg = <0 0x11006000 0 0x1000>;
|
||||
#pwm-cells = <2>;
|
||||
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_LOW>;
|
||||
clocks = <&topckgen CLK_TOP_PWM_SEL>,
|
||||
<&pericfg CLK_PERI_PWM_PD>,
|
||||
|
||||
@ -125,8 +125,7 @@ topckgen: topckgen@1001b000 {
|
||||
};
|
||||
|
||||
watchdog: watchdog@1001c000 {
|
||||
compatible = "mediatek,mt7986-wdt",
|
||||
"mediatek,mt6589-wdt";
|
||||
compatible = "mediatek,mt7986-wdt";
|
||||
reg = <0 0x1001c000 0 0x1000>;
|
||||
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#reset-cells = <1>;
|
||||
|
||||
@ -585,6 +585,15 @@ psci {
|
||||
method = "smc";
|
||||
};
|
||||
|
||||
clk13m: fixed-factor-clock-13m {
|
||||
compatible = "fixed-factor-clock";
|
||||
#clock-cells = <0>;
|
||||
clocks = <&clk26m>;
|
||||
clock-div = <2>;
|
||||
clock-mult = <1>;
|
||||
clock-output-names = "clk13m";
|
||||
};
|
||||
|
||||
clk26m: oscillator {
|
||||
compatible = "fixed-clock";
|
||||
#clock-cells = <0>;
|
||||
@ -968,8 +977,7 @@ systimer: timer@10017000 {
|
||||
"mediatek,mt6765-timer";
|
||||
reg = <0 0x10017000 0 0x1000>;
|
||||
interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&topckgen CLK_TOP_CLK13M>;
|
||||
clock-names = "clk13m";
|
||||
clocks = <&clk13m>;
|
||||
};
|
||||
|
||||
iommu: iommu@10205000 {
|
||||
|
||||
@ -47,14 +47,12 @@ core4 {
|
||||
core5 {
|
||||
cpu = <&cpu5>;
|
||||
};
|
||||
};
|
||||
|
||||
cluster1 {
|
||||
core0 {
|
||||
core6 {
|
||||
cpu = <&cpu6>;
|
||||
};
|
||||
|
||||
core1 {
|
||||
core7 {
|
||||
cpu = <&cpu7>;
|
||||
};
|
||||
};
|
||||
@ -211,10 +209,12 @@ l3_0: l3-cache {
|
||||
};
|
||||
};
|
||||
|
||||
clk13m: oscillator-13m {
|
||||
compatible = "fixed-clock";
|
||||
clk13m: fixed-factor-clock-13m {
|
||||
compatible = "fixed-factor-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-frequency = <13000000>;
|
||||
clocks = <&clk26m>;
|
||||
clock-div = <2>;
|
||||
clock-mult = <1>;
|
||||
clock-output-names = "clk13m";
|
||||
};
|
||||
|
||||
@ -330,8 +330,7 @@ pio: pinctrl@10005000 {
|
||||
};
|
||||
|
||||
watchdog: watchdog@10007000 {
|
||||
compatible = "mediatek,mt8186-wdt",
|
||||
"mediatek,mt6589-wdt";
|
||||
compatible = "mediatek,mt8186-wdt";
|
||||
mediatek,disable-extrst;
|
||||
reg = <0 0x10007000 0 0x1000>;
|
||||
#reset-cells = <1>;
|
||||
|
||||
@ -29,6 +29,15 @@ aliases {
|
||||
rdma4 = &rdma4;
|
||||
};
|
||||
|
||||
clk13m: fixed-factor-clock-13m {
|
||||
compatible = "fixed-factor-clock";
|
||||
#clock-cells = <0>;
|
||||
clocks = <&clk26m>;
|
||||
clock-div = <2>;
|
||||
clock-mult = <1>;
|
||||
clock-output-names = "clk13m";
|
||||
};
|
||||
|
||||
clk26m: oscillator0 {
|
||||
compatible = "fixed-clock";
|
||||
#clock-cells = <0>;
|
||||
@ -149,19 +158,16 @@ core2 {
|
||||
core3 {
|
||||
cpu = <&cpu3>;
|
||||
};
|
||||
};
|
||||
|
||||
cluster1 {
|
||||
core0 {
|
||||
core4 {
|
||||
cpu = <&cpu4>;
|
||||
};
|
||||
core1 {
|
||||
core5 {
|
||||
cpu = <&cpu5>;
|
||||
};
|
||||
core2 {
|
||||
core6 {
|
||||
cpu = <&cpu6>;
|
||||
};
|
||||
core3 {
|
||||
core7 {
|
||||
cpu = <&cpu7>;
|
||||
};
|
||||
};
|
||||
@ -531,8 +537,7 @@ systimer: timer@10017000 {
|
||||
"mediatek,mt6765-timer";
|
||||
reg = <0 0x10017000 0 0x1000>;
|
||||
interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH 0>;
|
||||
clocks = <&topckgen CLK_TOP_CSW_F26M_D2>;
|
||||
clock-names = "clk13m";
|
||||
clocks = <&clk13m>;
|
||||
};
|
||||
|
||||
pwrap: pwrap@10026000 {
|
||||
@ -575,6 +580,8 @@ scp_adsp: clock-controller@10720000 {
|
||||
compatible = "mediatek,mt8192-scp_adsp";
|
||||
reg = <0 0x10720000 0 0x1000>;
|
||||
#clock-cells = <1>;
|
||||
/* power domain dependency not upstreamed */
|
||||
status = "fail";
|
||||
};
|
||||
|
||||
uart0: serial@11002000 {
|
||||
|
||||
@ -150,22 +150,20 @@ core2 {
|
||||
core3 {
|
||||
cpu = <&cpu3>;
|
||||
};
|
||||
};
|
||||
|
||||
cluster1 {
|
||||
core0 {
|
||||
core4 {
|
||||
cpu = <&cpu4>;
|
||||
};
|
||||
|
||||
core1 {
|
||||
core5 {
|
||||
cpu = <&cpu5>;
|
||||
};
|
||||
|
||||
core2 {
|
||||
core6 {
|
||||
cpu = <&cpu6>;
|
||||
};
|
||||
|
||||
core3 {
|
||||
core7 {
|
||||
cpu = <&cpu7>;
|
||||
};
|
||||
};
|
||||
@ -244,6 +242,15 @@ sound: mt8195-sound {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
clk13m: fixed-factor-clock-13m {
|
||||
compatible = "fixed-factor-clock";
|
||||
#clock-cells = <0>;
|
||||
clocks = <&clk26m>;
|
||||
clock-div = <2>;
|
||||
clock-mult = <1>;
|
||||
clock-output-names = "clk13m";
|
||||
};
|
||||
|
||||
clk26m: oscillator-26m {
|
||||
compatible = "fixed-clock";
|
||||
#clock-cells = <0>;
|
||||
@ -683,8 +690,7 @@ power-domain@MT8195_POWER_DOMAIN_AUDIO {
|
||||
};
|
||||
|
||||
watchdog: watchdog@10007000 {
|
||||
compatible = "mediatek,mt8195-wdt",
|
||||
"mediatek,mt6589-wdt";
|
||||
compatible = "mediatek,mt8195-wdt";
|
||||
mediatek,disable-extrst;
|
||||
reg = <0 0x10007000 0 0x100>;
|
||||
#reset-cells = <1>;
|
||||
@ -701,7 +707,7 @@ systimer: timer@10017000 {
|
||||
"mediatek,mt6765-timer";
|
||||
reg = <0 0x10017000 0 0x1000>;
|
||||
interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH 0>;
|
||||
clocks = <&topckgen CLK_TOP_CLK26M_D2>;
|
||||
clocks = <&clk13m>;
|
||||
};
|
||||
|
||||
pwrap: pwrap@10024000 {
|
||||
@ -1410,6 +1416,7 @@ u3phy1: t-phy@11e30000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges = <0 0 0x11e30000 0xe00>;
|
||||
power-domains = <&spm MT8195_POWER_DOMAIN_SSUSB_PCIE_PHY>;
|
||||
status = "disabled";
|
||||
|
||||
u2port1: usb-phy@0 {
|
||||
|
||||
@ -1666,7 +1666,7 @@ vdd_hdmi: regulator-vdd-hdmi {
|
||||
vin-supply = <&vdd_5v0_sys>;
|
||||
};
|
||||
|
||||
vdd_cam_1v2: regulator-vdd-cam-1v8 {
|
||||
vdd_cam_1v2: regulator-vdd-cam-1v2 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vdd-cam-1v2";
|
||||
regulator-min-microvolt = <1200000>;
|
||||
|
||||
@ -137,7 +137,7 @@ usb1_ssphy: phy@58200 {
|
||||
#clock-cells = <0>;
|
||||
clocks = <&gcc GCC_USB1_PIPE_CLK>;
|
||||
clock-names = "pipe0";
|
||||
clock-output-names = "gcc_usb1_pipe_clk_src";
|
||||
clock-output-names = "usb3phy_1_cc_pipe_clk";
|
||||
};
|
||||
};
|
||||
|
||||
@ -180,7 +180,7 @@ usb0_ssphy: phy@78200 {
|
||||
#clock-cells = <0>;
|
||||
clocks = <&gcc GCC_USB0_PIPE_CLK>;
|
||||
clock-names = "pipe0";
|
||||
clock-output-names = "gcc_usb0_pipe_clk_src";
|
||||
clock-output-names = "usb3phy_0_cc_pipe_clk";
|
||||
};
|
||||
};
|
||||
|
||||
@ -197,9 +197,9 @@ qusb_phy_0: phy@79000 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pcie_qmp0: phy@86000 {
|
||||
compatible = "qcom,ipq8074-qmp-pcie-phy";
|
||||
reg = <0x00086000 0x1c4>;
|
||||
pcie_qmp0: phy@84000 {
|
||||
compatible = "qcom,ipq8074-qmp-gen3-pcie-phy";
|
||||
reg = <0x00084000 0x1bc>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
@ -213,15 +213,16 @@ pcie_qmp0: phy@86000 {
|
||||
"common";
|
||||
status = "disabled";
|
||||
|
||||
pcie_phy0: phy@86200 {
|
||||
reg = <0x86200 0x16c>,
|
||||
<0x86400 0x200>,
|
||||
<0x86800 0x4f4>;
|
||||
pcie_phy0: phy@84200 {
|
||||
reg = <0x84200 0x16c>,
|
||||
<0x84400 0x200>,
|
||||
<0x84800 0x1f0>,
|
||||
<0x84c00 0xf4>;
|
||||
#phy-cells = <0>;
|
||||
#clock-cells = <0>;
|
||||
clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
|
||||
clock-names = "pipe0";
|
||||
clock-output-names = "pcie_0_pipe_clk";
|
||||
clock-output-names = "pcie20_phy0_pipe_clk";
|
||||
};
|
||||
};
|
||||
|
||||
@ -242,14 +243,14 @@ pcie_qmp1: phy@8e000 {
|
||||
status = "disabled";
|
||||
|
||||
pcie_phy1: phy@8e200 {
|
||||
reg = <0x8e200 0x16c>,
|
||||
reg = <0x8e200 0x130>,
|
||||
<0x8e400 0x200>,
|
||||
<0x8e800 0x4f4>;
|
||||
<0x8e800 0x1f8>;
|
||||
#phy-cells = <0>;
|
||||
#clock-cells = <0>;
|
||||
clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
|
||||
clock-names = "pipe0";
|
||||
clock-output-names = "pcie_1_pipe_clk";
|
||||
clock-output-names = "pcie20_phy1_pipe_clk";
|
||||
};
|
||||
};
|
||||
|
||||
@ -750,9 +751,9 @@ pcie1: pci@10000000 {
|
||||
phy-names = "pciephy";
|
||||
|
||||
ranges = <0x81000000 0 0x10200000 0x10200000
|
||||
0 0x100000 /* downstream I/O */
|
||||
0x82000000 0 0x10300000 0x10300000
|
||||
0 0xd00000>; /* non-prefetchable memory */
|
||||
0 0x10000>, /* downstream I/O */
|
||||
<0x82000000 0 0x10220000 0x10220000
|
||||
0 0xfde0000>; /* non-prefetchable memory */
|
||||
|
||||
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "msi";
|
||||
@ -795,16 +796,18 @@ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
|
||||
};
|
||||
|
||||
pcie0: pci@20000000 {
|
||||
compatible = "qcom,pcie-ipq8074";
|
||||
compatible = "qcom,pcie-ipq8074-gen3";
|
||||
reg = <0x20000000 0xf1d>,
|
||||
<0x20000f20 0xa8>,
|
||||
<0x00080000 0x2000>,
|
||||
<0x20001000 0x1000>,
|
||||
<0x00080000 0x4000>,
|
||||
<0x20100000 0x1000>;
|
||||
reg-names = "dbi", "elbi", "parf", "config";
|
||||
reg-names = "dbi", "elbi", "atu", "parf", "config";
|
||||
device_type = "pci";
|
||||
linux,pci-domain = <0>;
|
||||
bus-range = <0x00 0xff>;
|
||||
num-lanes = <1>;
|
||||
max-link-speed = <3>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
|
||||
@ -812,9 +815,9 @@ pcie0: pci@20000000 {
|
||||
phy-names = "pciephy";
|
||||
|
||||
ranges = <0x81000000 0 0x20200000 0x20200000
|
||||
0 0x100000 /* downstream I/O */
|
||||
0x82000000 0 0x20300000 0x20300000
|
||||
0 0xd00000>; /* non-prefetchable memory */
|
||||
0 0x10000>, /* downstream I/O */
|
||||
<0x82000000 0 0x20220000 0x20220000
|
||||
0 0xfde0000>; /* non-prefetchable memory */
|
||||
|
||||
interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "msi";
|
||||
@ -832,28 +835,30 @@ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
|
||||
clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
|
||||
<&gcc GCC_PCIE0_AXI_M_CLK>,
|
||||
<&gcc GCC_PCIE0_AXI_S_CLK>,
|
||||
<&gcc GCC_PCIE0_AHB_CLK>,
|
||||
<&gcc GCC_PCIE0_AUX_CLK>;
|
||||
|
||||
<&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
|
||||
<&gcc GCC_PCIE0_RCHNG_CLK>;
|
||||
clock-names = "iface",
|
||||
"axi_m",
|
||||
"axi_s",
|
||||
"ahb",
|
||||
"aux";
|
||||
"axi_bridge",
|
||||
"rchng";
|
||||
|
||||
resets = <&gcc GCC_PCIE0_PIPE_ARES>,
|
||||
<&gcc GCC_PCIE0_SLEEP_ARES>,
|
||||
<&gcc GCC_PCIE0_CORE_STICKY_ARES>,
|
||||
<&gcc GCC_PCIE0_AXI_MASTER_ARES>,
|
||||
<&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
|
||||
<&gcc GCC_PCIE0_AHB_ARES>,
|
||||
<&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>;
|
||||
<&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
|
||||
<&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
|
||||
reset-names = "pipe",
|
||||
"sleep",
|
||||
"sticky",
|
||||
"axi_m",
|
||||
"axi_s",
|
||||
"ahb",
|
||||
"axi_m_sticky";
|
||||
"axi_m_sticky",
|
||||
"axi_s_sticky";
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
@ -455,7 +455,7 @@ tlmm: pinctrl@1000000 {
|
||||
reg = <0x1000000 0x300000>;
|
||||
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
|
||||
gpio-controller;
|
||||
gpio-ranges = <&tlmm 0 0 155>;
|
||||
gpio-ranges = <&tlmm 0 0 142>;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
|
||||
@ -1,5 +1,6 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-only
|
||||
/* Copyright (c) Jean Thomas <virgule@jeanthomas.me>
|
||||
/*
|
||||
* Copyright (c) Jean Thomas <virgule@jeanthomas.me>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,5 +1,6 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-only
|
||||
/* Copyright (c) Jean Thomas <virgule@jeanthomas.me>
|
||||
/*
|
||||
* Copyright (c) Jean Thomas <virgule@jeanthomas.me>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,7 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-only
|
||||
/* Copyright (c) 2015, LGE Inc. All rights reserved.
|
||||
/*
|
||||
* Copyright (c) 2015, LGE Inc. All rights reserved.
|
||||
* Copyright (c) 2016, The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2021, Petr Vorel <petr.vorel@gmail.com>
|
||||
* Copyright (c) 2021-2022, Petr Vorel <petr.vorel@gmail.com>
|
||||
* Copyright (c) 2022, Dominik Kobinski <dominikkobinski314@gmail.com>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
@ -13,6 +15,9 @@
|
||||
/* cont_splash_mem has different memory mapping */
|
||||
/delete-node/ &cont_splash_mem;
|
||||
|
||||
/* disabled on downstream, conflicts with cont_splash_mem */
|
||||
/delete-node/ &dfps_data_mem;
|
||||
|
||||
/ {
|
||||
model = "LG Nexus 5X";
|
||||
compatible = "lg,bullhead", "qcom,msm8992";
|
||||
@ -47,7 +52,17 @@ ramoops@1ff00000 {
|
||||
};
|
||||
|
||||
cont_splash_mem: memory@3400000 {
|
||||
reg = <0 0x03400000 0 0x1200000>;
|
||||
reg = <0 0x03400000 0 0xc00000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
reserved@5000000 {
|
||||
reg = <0x0 0x05000000 0x0 0x1a00000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
reserved@6c00000 {
|
||||
reg = <0x0 0x06c00000 0x0 0x400000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
@ -79,8 +94,8 @@ pm8994_regulators: pm8994-regulators {
|
||||
/* S1, S2, S6 and S12 are managed by RPMPD */
|
||||
|
||||
pm8994_s1: s1 {
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <800000>;
|
||||
regulator-min-microvolt = <1025000>;
|
||||
regulator-max-microvolt = <1025000>;
|
||||
};
|
||||
|
||||
pm8994_s2: s2 {
|
||||
@ -236,9 +251,8 @@ pm8994_l25: l25 {
|
||||
};
|
||||
|
||||
pm8994_l26: l26 {
|
||||
/* TODO: value from downstream
|
||||
regulator-min-microvolt = <987500>;
|
||||
fails to apply */
|
||||
regulator-max-microvolt = <987500>;
|
||||
};
|
||||
|
||||
pm8994_l27: l27 {
|
||||
@ -252,19 +266,13 @@ pm8994_l28: l28 {
|
||||
};
|
||||
|
||||
pm8994_l29: l29 {
|
||||
/* TODO: Unsupported voltage range.
|
||||
regulator-min-microvolt = <2800000>;
|
||||
regulator-max-microvolt = <2800000>;
|
||||
qcom,init-voltage = <2800000>;
|
||||
*/
|
||||
};
|
||||
|
||||
pm8994_l30: l30 {
|
||||
/* TODO: get this verified
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
qcom,init-voltage = <1800000>;
|
||||
*/
|
||||
};
|
||||
|
||||
pm8994_l31: l31 {
|
||||
@ -273,11 +281,8 @@ pm8994_l31: l31 {
|
||||
};
|
||||
|
||||
pm8994_l32: l32 {
|
||||
/* TODO: get this verified
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
qcom,init-voltage = <1800000>;
|
||||
*/
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
@ -1,5 +1,6 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-only
|
||||
/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
|
||||
/*
|
||||
* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
|
||||
*/
|
||||
|
||||
#include "msm8994.dtsi"
|
||||
|
||||
@ -944,10 +944,6 @@ touch_int_sleep: touch-int-sleep {
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* For reasons that are currently unknown (but probably related to fusb301), USB takes about
|
||||
* 6 minutes to wake up (nothing interesting in kernel logs), but then it works as it should.
|
||||
*/
|
||||
&usb3 {
|
||||
status = "okay";
|
||||
qcom,select-utmi-as-pipe-clk;
|
||||
@ -956,6 +952,7 @@ &usb3 {
|
||||
&usb3_dwc3 {
|
||||
extcon = <&usb3_id>;
|
||||
dr_mode = "peripheral";
|
||||
maximum-speed = "high-speed";
|
||||
phys = <&hsusb_phy1>;
|
||||
phy-names = "usb2-phy";
|
||||
snps,hird-threshold = /bits/ 8 <0>;
|
||||
|
||||
@ -712,7 +712,7 @@ gcc: clock-controller@300000 {
|
||||
#power-domain-cells = <1>;
|
||||
reg = <0x00300000 0x90000>;
|
||||
|
||||
clocks = <&rpmcc RPM_SMD_BB_CLK1>,
|
||||
clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
|
||||
<&rpmcc RPM_SMD_LN_BB_CLK>,
|
||||
<&sleep_clk>,
|
||||
<&pciephy_0>,
|
||||
@ -829,9 +829,11 @@ a2noc: interconnect@583000 {
|
||||
compatible = "qcom,msm8996-a2noc";
|
||||
reg = <0x00583000 0x7000>;
|
||||
#interconnect-cells = <1>;
|
||||
clock-names = "bus", "bus_a";
|
||||
clock-names = "bus", "bus_a", "aggre2_ufs_axi", "ufs_axi";
|
||||
clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>,
|
||||
<&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>;
|
||||
<&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>,
|
||||
<&gcc GCC_AGGRE2_UFS_AXI_CLK>,
|
||||
<&gcc GCC_UFS_AXI_CLK>;
|
||||
};
|
||||
|
||||
mnoc: interconnect@5a4000 {
|
||||
@ -1050,7 +1052,7 @@ dsi0_phy: dsi-phy@994400 {
|
||||
#clock-cells = <1>;
|
||||
#phy-cells = <0>;
|
||||
|
||||
clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_BB_CLK1>;
|
||||
clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
|
||||
clock-names = "iface", "ref";
|
||||
status = "disabled";
|
||||
};
|
||||
@ -1118,7 +1120,7 @@ dsi1_phy: dsi-phy@996400 {
|
||||
#clock-cells = <1>;
|
||||
#phy-cells = <0>;
|
||||
|
||||
clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_BB_CLK1>;
|
||||
clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
|
||||
clock-names = "iface", "ref";
|
||||
status = "disabled";
|
||||
};
|
||||
@ -2932,8 +2934,8 @@ kryocc: clock-controller@6400000 {
|
||||
compatible = "qcom,msm8996-apcc";
|
||||
reg = <0x06400000 0x90000>;
|
||||
|
||||
clock-names = "xo";
|
||||
clocks = <&rpmcc RPM_SMD_BB_CLK1>;
|
||||
clock-names = "xo", "sys_apcs_aux";
|
||||
clocks = <&rpmcc RPM_SMD_XO_A_CLK_SRC>, <&apcs_glb>;
|
||||
|
||||
#clock-cells = <1>;
|
||||
};
|
||||
@ -3052,7 +3054,7 @@ sdhc1: mmc@7464900 {
|
||||
clock-names = "iface", "core", "xo";
|
||||
clocks = <&gcc GCC_SDCC1_AHB_CLK>,
|
||||
<&gcc GCC_SDCC1_APPS_CLK>,
|
||||
<&rpmcc RPM_SMD_BB_CLK1>;
|
||||
<&rpmcc RPM_SMD_XO_CLK_SRC>;
|
||||
resets = <&gcc GCC_SDCC1_BCR>;
|
||||
|
||||
pinctrl-names = "default", "sleep";
|
||||
@ -3076,7 +3078,7 @@ sdhc2: mmc@74a4900 {
|
||||
clock-names = "iface", "core", "xo";
|
||||
clocks = <&gcc GCC_SDCC2_AHB_CLK>,
|
||||
<&gcc GCC_SDCC2_APPS_CLK>,
|
||||
<&rpmcc RPM_SMD_BB_CLK1>;
|
||||
<&rpmcc RPM_SMD_XO_CLK_SRC>;
|
||||
resets = <&gcc GCC_SDCC2_BCR>;
|
||||
|
||||
pinctrl-names = "default", "sleep";
|
||||
@ -3383,7 +3385,7 @@ adsp_pil: remoteproc@9300000 {
|
||||
interrupt-names = "wdog", "fatal", "ready",
|
||||
"handover", "stop-ack";
|
||||
|
||||
clocks = <&rpmcc RPM_SMD_BB_CLK1>;
|
||||
clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
|
||||
clock-names = "xo";
|
||||
|
||||
memory-region = <&adsp_mem>;
|
||||
|
||||
@ -16,8 +16,9 @@ pmk8350: pmic@0 {
|
||||
#size-cells = <0>;
|
||||
|
||||
pmk8350_pon: pon@1300 {
|
||||
compatible = "qcom,pm8998-pon";
|
||||
reg = <0x1300>;
|
||||
compatible = "qcom,pmk8350-pon";
|
||||
reg = <0x1300>, <0x800>;
|
||||
reg-names = "hlos", "pbs";
|
||||
|
||||
pon_pwrkey: pwrkey {
|
||||
compatible = "qcom,pmk8350-pwrkey";
|
||||
|
||||
@ -792,7 +792,7 @@ pcie_phy: phy@7786000 {
|
||||
|
||||
clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
|
||||
resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
|
||||
<&gcc 21>;
|
||||
<&gcc GCC_PCIE_0_PIPE_ARES>;
|
||||
reset-names = "phy", "pipe";
|
||||
|
||||
clock-output-names = "pcie_0_pipe_clk";
|
||||
@ -1322,12 +1322,12 @@ pcie: pci@10000000 {
|
||||
<&gcc GCC_PCIE_0_SLV_AXI_CLK>;
|
||||
clock-names = "iface", "aux", "master_bus", "slave_bus";
|
||||
|
||||
resets = <&gcc 18>,
|
||||
<&gcc 17>,
|
||||
<&gcc 15>,
|
||||
<&gcc 19>,
|
||||
resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
|
||||
<&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
|
||||
<&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
|
||||
<&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
|
||||
<&gcc GCC_PCIE_0_BCR>,
|
||||
<&gcc 16>;
|
||||
<&gcc GCC_PCIE_0_AHB_ARES>;
|
||||
reset-names = "axi_m",
|
||||
"axi_s",
|
||||
"axi_m_sticky",
|
||||
|
||||
@ -3238,8 +3238,8 @@ spmi_bus: spmi@c440000 {
|
||||
interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
qcom,ee = <0>;
|
||||
qcom,channel = <0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
#address-cells = <2>;
|
||||
#size-cells = <0>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <4>;
|
||||
cell-index = <0>;
|
||||
|
||||
@ -4242,8 +4242,8 @@ spmi_bus: spmi@c440000 {
|
||||
interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
qcom,ee = <0>;
|
||||
qcom,channel = <0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
#address-cells = <2>;
|
||||
#size-cells = <0>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <4>;
|
||||
};
|
||||
|
||||
@ -1287,6 +1287,7 @@ usb_0: usb@a6f8800 {
|
||||
"ss_phy_irq";
|
||||
|
||||
power-domains = <&gcc USB30_PRIM_GDSC>;
|
||||
required-opps = <&rpmhpd_opp_nom>;
|
||||
|
||||
resets = <&gcc GCC_USB30_PRIM_BCR>;
|
||||
|
||||
@ -1341,6 +1342,7 @@ usb_1: usb@a8f8800 {
|
||||
"ss_phy_irq";
|
||||
|
||||
power-domains = <&gcc USB30_SEC_GDSC>;
|
||||
required-opps = <&rpmhpd_opp_nom>;
|
||||
|
||||
resets = <&gcc GCC_USB30_SEC_BCR>;
|
||||
|
||||
@ -1470,8 +1472,8 @@ spmi_bus: spmi@c440000 {
|
||||
interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
qcom,ee = <0>;
|
||||
qcom,channel = <0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
#address-cells = <2>;
|
||||
#size-cells = <0>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <4>;
|
||||
};
|
||||
|
||||
@ -969,7 +969,7 @@ sdc2_card_det_n: sd-card-det-n {
|
||||
};
|
||||
|
||||
wcd_intr_default: wcd_intr_default {
|
||||
pins = <54>;
|
||||
pins = "gpio54";
|
||||
function = "gpio";
|
||||
|
||||
input-enable;
|
||||
|
||||
@ -40,17 +40,18 @@ extcon_usb: extcon-usb {
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
status = "okay";
|
||||
compatible = "gpio-keys";
|
||||
autorepeat;
|
||||
|
||||
key-vol-dn {
|
||||
pinctrl-0 = <&vol_down_n>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
key-volume-down {
|
||||
label = "Volume Down";
|
||||
gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
|
||||
linux,input-type = <1>;
|
||||
linux,code = <KEY_VOLUMEDOWN>;
|
||||
gpio-key,wakeup;
|
||||
debounce-interval = <15>;
|
||||
linux,can-disable;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
@ -108,6 +109,14 @@ &sdhc_1 {
|
||||
|
||||
&tlmm {
|
||||
gpio-reserved-ranges = <22 2>, <28 6>;
|
||||
|
||||
vol_down_n: vol-down-n-state {
|
||||
pins = "gpio47";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
input-enable;
|
||||
};
|
||||
};
|
||||
|
||||
&usb3 {
|
||||
|
||||
@ -442,9 +442,9 @@ hsusb_phy1: phy@1613000 {
|
||||
reg = <0x01613000 0x180>;
|
||||
#phy-cells = <0>;
|
||||
|
||||
clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
|
||||
<&gcc GCC_AHB2PHY_USB_CLK>;
|
||||
clock-names = "ref", "cfg_ahb";
|
||||
clocks = <&gcc GCC_AHB2PHY_USB_CLK>,
|
||||
<&rpmcc RPM_SMD_XO_CLK_SRC>;
|
||||
clock-names = "cfg_ahb", "ref";
|
||||
|
||||
resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
|
||||
status = "disabled";
|
||||
|
||||
@ -342,13 +342,12 @@ last_log_region: memory@ffbc0000 {
|
||||
};
|
||||
|
||||
ramoops: ramoops@ffc00000 {
|
||||
compatible = "removed-dma-pool", "ramoops";
|
||||
reg = <0 0xffc00000 0 0x00100000>;
|
||||
compatible = "ramoops";
|
||||
reg = <0 0xffc00000 0 0x100000>;
|
||||
record-size = <0x1000>;
|
||||
console-size = <0x40000>;
|
||||
ftrace-size = <0x0>;
|
||||
msg-size = <0x20000 0x20000>;
|
||||
cc-size = <0x0>;
|
||||
ecc-size = <16>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
|
||||
@ -33,9 +33,10 @@ chosen {
|
||||
framebuffer: framebuffer@9c000000 {
|
||||
compatible = "simple-framebuffer";
|
||||
reg = <0 0x9c000000 0 0x2300000>;
|
||||
width = <1644>;
|
||||
height = <3840>;
|
||||
stride = <(1644 * 4)>;
|
||||
/* Griffin BL initializes in 2.5k mode, not 4k */
|
||||
width = <1096>;
|
||||
height = <2560>;
|
||||
stride = <(1096 * 4)>;
|
||||
format = "a8r8g8b8";
|
||||
/*
|
||||
* That's (going to be) a lot of clocks, but it's necessary due
|
||||
|
||||
@ -1043,8 +1043,6 @@ uart2: serial@98c000 {
|
||||
interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
|
||||
power-domains = <&rpmhpd SM8350_CX>;
|
||||
operating-points-v2 = <&qup_opp_table_100mhz>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
|
||||
@ -991,8 +991,6 @@ uart20: serial@894000 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&qup_uart20_default>;
|
||||
interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
@ -1387,8 +1385,6 @@ uart7: serial@99c000 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
|
||||
interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
@ -437,20 +437,6 @@ wm8962_endpoint: endpoint {
|
||||
};
|
||||
};
|
||||
|
||||
/* 0 - lcd_reset */
|
||||
/* 1 - lcd_pwr */
|
||||
/* 2 - lcd_select */
|
||||
/* 3 - backlight-enable */
|
||||
/* 4 - Touch_shdwn */
|
||||
/* 5 - LCD_H_pol */
|
||||
/* 6 - lcd_V_pol */
|
||||
gpio_exp1: gpio@20 {
|
||||
compatible = "onnn,pca9654";
|
||||
reg = <0x20>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
touchscreen@26 {
|
||||
compatible = "ilitek,ili2117";
|
||||
reg = <0x26>;
|
||||
@ -482,6 +468,16 @@ hd3ss3220_out_ep: endpoint {
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gpio_exp1: gpio@70 {
|
||||
compatible = "nxp,pca9538";
|
||||
reg = <0x70>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
gpio-line-names = "lcd_reset", "lcd_pwr", "lcd_select",
|
||||
"backlight-enable", "Touch_shdwn",
|
||||
"LCD_H_pol", "lcd_V_pol";
|
||||
};
|
||||
};
|
||||
|
||||
&lvds0 {
|
||||
|
||||
@ -306,7 +306,8 @@ main_spi0: spi@20100000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
|
||||
clocks = <&k3_clks 172 0>;
|
||||
clocks = <&k3_clks 141 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
main_spi1: spi@20110000 {
|
||||
@ -316,7 +317,8 @@ main_spi1: spi@20110000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
|
||||
clocks = <&k3_clks 173 0>;
|
||||
clocks = <&k3_clks 142 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
main_spi2: spi@20120000 {
|
||||
@ -326,7 +328,8 @@ main_spi2: spi@20120000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
|
||||
clocks = <&k3_clks 174 0>;
|
||||
clocks = <&k3_clks 143 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
main_gpio_intr: interrupt-controller@a00000 {
|
||||
|
||||
@ -42,6 +42,7 @@ mcu_spi0: spi@4b00000 {
|
||||
#size-cells = <0>;
|
||||
power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
|
||||
clocks = <&k3_clks 147 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
mcu_spi1: spi@4b10000 {
|
||||
@ -52,6 +53,7 @@ mcu_spi1: spi@4b10000 {
|
||||
#size-cells = <0>;
|
||||
power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
|
||||
clocks = <&k3_clks 148 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
mcu_gpio_intr: interrupt-controller@4210000 {
|
||||
|
||||
@ -80,7 +80,7 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
|
||||
};
|
||||
};
|
||||
|
||||
&wkup_pmx0 {
|
||||
&wkup_pmx2 {
|
||||
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
|
||||
pinctrl-single,pins = <
|
||||
J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
|
||||
|
||||
@ -56,7 +56,34 @@ chipid@43000014 {
|
||||
wkup_pmx0: pinctrl@4301c000 {
|
||||
compatible = "pinctrl-single";
|
||||
/* Proxy 0 addressing */
|
||||
reg = <0x00 0x4301c000 0x00 0x178>;
|
||||
reg = <0x00 0x4301c000 0x00 0x34>;
|
||||
#pinctrl-cells = <1>;
|
||||
pinctrl-single,register-width = <32>;
|
||||
pinctrl-single,function-mask = <0xffffffff>;
|
||||
};
|
||||
|
||||
wkup_pmx1: pinctrl@0x4301c038 {
|
||||
compatible = "pinctrl-single";
|
||||
/* Proxy 0 addressing */
|
||||
reg = <0x00 0x4301c038 0x00 0x8>;
|
||||
#pinctrl-cells = <1>;
|
||||
pinctrl-single,register-width = <32>;
|
||||
pinctrl-single,function-mask = <0xffffffff>;
|
||||
};
|
||||
|
||||
wkup_pmx2: pinctrl@0x4301c068 {
|
||||
compatible = "pinctrl-single";
|
||||
/* Proxy 0 addressing */
|
||||
reg = <0x00 0x4301c068 0x00 0xec>;
|
||||
#pinctrl-cells = <1>;
|
||||
pinctrl-single,register-width = <32>;
|
||||
pinctrl-single,function-mask = <0xffffffff>;
|
||||
};
|
||||
|
||||
wkup_pmx3: pinctrl@0x4301c174 {
|
||||
compatible = "pinctrl-single";
|
||||
/* Proxy 0 addressing */
|
||||
reg = <0x00 0x4301c174 0x00 0x20>;
|
||||
#pinctrl-cells = <1>;
|
||||
pinctrl-single,register-width = <32>;
|
||||
pinctrl-single,function-mask = <0xffffffff>;
|
||||
|
||||
@ -825,6 +825,7 @@ dwc3_0: usb@fe200000 {
|
||||
clock-names = "bus_early", "ref";
|
||||
iommus = <&smmu 0x860>;
|
||||
snps,quirk-frame-length-adjustment = <0x20>;
|
||||
snps,resume-hs-terminations;
|
||||
/* dma-coherent; */
|
||||
};
|
||||
};
|
||||
@ -851,6 +852,7 @@ dwc3_1: usb@fe300000 {
|
||||
clock-names = "bus_early", "ref";
|
||||
iommus = <&smmu 0x861>;
|
||||
snps,quirk-frame-length-adjustment = <0x20>;
|
||||
snps,resume-hs-terminations;
|
||||
/* dma-coherent; */
|
||||
};
|
||||
};
|
||||
|
||||
@ -2757,7 +2757,7 @@ static const struct arm64_cpu_capabilities arm64_elf_hwcaps[] = {
|
||||
HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_FP_SHIFT, 4, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FPHP),
|
||||
HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_AdvSIMD_SHIFT, 4, FTR_SIGNED, 0, CAP_HWCAP, KERNEL_HWCAP_ASIMD),
|
||||
HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_AdvSIMD_SHIFT, 4, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDHP),
|
||||
HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_DIT_SHIFT, 4, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DIT),
|
||||
HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_DIT_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DIT),
|
||||
HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_DPB_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DCPOP),
|
||||
HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_DPB_SHIFT, 4, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_DCPODP),
|
||||
HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_JSCVT_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_JSCVT),
|
||||
|
||||
@ -782,7 +782,7 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx, bool ext
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
move_imm(ctx, t1, func_addr, is32);
|
||||
move_addr(ctx, t1, func_addr);
|
||||
emit_insn(ctx, jirl, t1, LOONGARCH_GPR_RA, 0);
|
||||
move_reg(ctx, regmap[BPF_REG_0], LOONGARCH_GPR_A0);
|
||||
break;
|
||||
|
||||
@ -80,6 +80,27 @@ static inline void emit_sext_32(struct jit_ctx *ctx, enum loongarch_gpr reg, boo
|
||||
emit_insn(ctx, addiw, reg, reg, 0);
|
||||
}
|
||||
|
||||
static inline void move_addr(struct jit_ctx *ctx, enum loongarch_gpr rd, u64 addr)
|
||||
{
|
||||
u64 imm_11_0, imm_31_12, imm_51_32, imm_63_52;
|
||||
|
||||
/* lu12iw rd, imm_31_12 */
|
||||
imm_31_12 = (addr >> 12) & 0xfffff;
|
||||
emit_insn(ctx, lu12iw, rd, imm_31_12);
|
||||
|
||||
/* ori rd, rd, imm_11_0 */
|
||||
imm_11_0 = addr & 0xfff;
|
||||
emit_insn(ctx, ori, rd, rd, imm_11_0);
|
||||
|
||||
/* lu32id rd, imm_51_32 */
|
||||
imm_51_32 = (addr >> 32) & 0xfffff;
|
||||
emit_insn(ctx, lu32id, rd, imm_51_32);
|
||||
|
||||
/* lu52id rd, rd, imm_63_52 */
|
||||
imm_63_52 = (addr >> 52) & 0xfff;
|
||||
emit_insn(ctx, lu52id, rd, rd, imm_63_52);
|
||||
}
|
||||
|
||||
static inline void move_imm(struct jit_ctx *ctx, enum loongarch_gpr rd, long imm, bool is32)
|
||||
{
|
||||
long imm_11_0, imm_31_12, imm_51_32, imm_63_52, imm_51_0, imm_51_31;
|
||||
|
||||
@ -45,6 +45,8 @@ do_trace:
|
||||
jbsr syscall_trace_enter
|
||||
RESTORE_SWITCH_STACK
|
||||
addql #4,%sp
|
||||
addql #1,%d0
|
||||
jeq ret_from_exception
|
||||
movel %sp@(PT_OFF_ORIG_D0),%d1
|
||||
movel #-ENOSYS,%d0
|
||||
cmpl #NR_syscalls,%d1
|
||||
|
||||
@ -19,6 +19,7 @@ config HEARTBEAT
|
||||
# We have a dedicated heartbeat LED. :-)
|
||||
config PROC_HARDWARE
|
||||
bool "/proc/hardware support"
|
||||
depends on PROC_FS
|
||||
help
|
||||
Say Y here to support the /proc/hardware file, which gives you
|
||||
access to information about the machine you're running on,
|
||||
|
||||
@ -90,6 +90,8 @@ ENTRY(system_call)
|
||||
jbsr syscall_trace_enter
|
||||
RESTORE_SWITCH_STACK
|
||||
addql #4,%sp
|
||||
addql #1,%d0
|
||||
jeq ret_from_exception
|
||||
movel %d3,%a0
|
||||
jbsr %a0@
|
||||
movel %d0,%sp@(PT_OFF_D0) /* save the return value */
|
||||
|
||||
@ -184,9 +184,12 @@ do_trace_entry:
|
||||
jbsr syscall_trace_enter
|
||||
RESTORE_SWITCH_STACK
|
||||
addql #4,%sp
|
||||
addql #1,%d0 | optimization for cmpil #-1,%d0
|
||||
jeq ret_from_syscall
|
||||
movel %sp@(PT_OFF_ORIG_D0),%d0
|
||||
cmpl #NR_syscalls,%d0
|
||||
jcs syscall
|
||||
jra ret_from_syscall
|
||||
badsys:
|
||||
movel #-ENOSYS,%sp@(PT_OFF_D0)
|
||||
jra ret_from_syscall
|
||||
|
||||
@ -113,7 +113,7 @@ otg_power: fixedregulator@2 {
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
|
||||
gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpf 15 GPIO_ACTIVE_LOW>;
|
||||
enable-active-high;
|
||||
};
|
||||
};
|
||||
|
||||
@ -38,7 +38,7 @@ static inline bool mips_syscall_is_indirect(struct task_struct *task,
|
||||
static inline long syscall_get_nr(struct task_struct *task,
|
||||
struct pt_regs *regs)
|
||||
{
|
||||
return current_thread_info()->syscall;
|
||||
return task_thread_info(task)->syscall;
|
||||
}
|
||||
|
||||
static inline void mips_syscall_update_nr(struct task_struct *task,
|
||||
|
||||
@ -90,7 +90,7 @@ aflags-$(CONFIG_CPU_LITTLE_ENDIAN) += -mlittle-endian
|
||||
|
||||
ifeq ($(HAS_BIARCH),y)
|
||||
KBUILD_CFLAGS += -m$(BITS)
|
||||
KBUILD_AFLAGS += -m$(BITS) -Wl,-a$(BITS)
|
||||
KBUILD_AFLAGS += -m$(BITS)
|
||||
KBUILD_LDFLAGS += -m elf$(BITS)$(LDEMULATION)
|
||||
endif
|
||||
|
||||
|
||||
@ -1179,15 +1179,12 @@ static inline void __radix__flush_tlb_range(struct mm_struct *mm,
|
||||
}
|
||||
}
|
||||
} else {
|
||||
bool hflush = false;
|
||||
bool hflush;
|
||||
unsigned long hstart, hend;
|
||||
|
||||
if (IS_ENABLED(CONFIG_TRANSPARENT_HUGEPAGE)) {
|
||||
hstart = (start + PMD_SIZE - 1) & PMD_MASK;
|
||||
hend = end & PMD_MASK;
|
||||
if (hstart < hend)
|
||||
hflush = true;
|
||||
}
|
||||
hstart = (start + PMD_SIZE - 1) & PMD_MASK;
|
||||
hend = end & PMD_MASK;
|
||||
hflush = IS_ENABLED(CONFIG_TRANSPARENT_HUGEPAGE) && hstart < hend;
|
||||
|
||||
if (type == FLUSH_TYPE_LOCAL) {
|
||||
asm volatile("ptesync": : :"memory");
|
||||
|
||||
@ -11,7 +11,11 @@ LDFLAGS_vmlinux :=
|
||||
ifeq ($(CONFIG_DYNAMIC_FTRACE),y)
|
||||
LDFLAGS_vmlinux := --no-relax
|
||||
KBUILD_CPPFLAGS += -DCC_USING_PATCHABLE_FUNCTION_ENTRY
|
||||
CC_FLAGS_FTRACE := -fpatchable-function-entry=8
|
||||
ifeq ($(CONFIG_RISCV_ISA_C),y)
|
||||
CC_FLAGS_FTRACE := -fpatchable-function-entry=4
|
||||
else
|
||||
CC_FLAGS_FTRACE := -fpatchable-function-entry=2
|
||||
endif
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_CMODEL_MEDLOW),y)
|
||||
|
||||
@ -42,6 +42,14 @@ struct dyn_arch_ftrace {
|
||||
* 2) jalr: setting low-12 offset to ra, jump to ra, and set ra to
|
||||
* return address (original pc + 4)
|
||||
*
|
||||
*<ftrace enable>:
|
||||
* 0: auipc t0/ra, 0x?
|
||||
* 4: jalr t0/ra, ?(t0/ra)
|
||||
*
|
||||
*<ftrace disable>:
|
||||
* 0: nop
|
||||
* 4: nop
|
||||
*
|
||||
* Dynamic ftrace generates probes to call sites, so we must deal with
|
||||
* both auipc and jalr at the same time.
|
||||
*/
|
||||
@ -52,25 +60,43 @@ struct dyn_arch_ftrace {
|
||||
#define AUIPC_OFFSET_MASK (0xfffff000)
|
||||
#define AUIPC_PAD (0x00001000)
|
||||
#define JALR_SHIFT 20
|
||||
#define JALR_BASIC (0x000080e7)
|
||||
#define AUIPC_BASIC (0x00000097)
|
||||
#define JALR_RA (0x000080e7)
|
||||
#define AUIPC_RA (0x00000097)
|
||||
#define JALR_T0 (0x000282e7)
|
||||
#define AUIPC_T0 (0x00000297)
|
||||
#define NOP4 (0x00000013)
|
||||
|
||||
#define make_call(caller, callee, call) \
|
||||
#define to_jalr_t0(offset) \
|
||||
(((offset & JALR_OFFSET_MASK) << JALR_SHIFT) | JALR_T0)
|
||||
|
||||
#define to_auipc_t0(offset) \
|
||||
((offset & JALR_SIGN_MASK) ? \
|
||||
(((offset & AUIPC_OFFSET_MASK) + AUIPC_PAD) | AUIPC_T0) : \
|
||||
((offset & AUIPC_OFFSET_MASK) | AUIPC_T0))
|
||||
|
||||
#define make_call_t0(caller, callee, call) \
|
||||
do { \
|
||||
call[0] = to_auipc_insn((unsigned int)((unsigned long)callee - \
|
||||
(unsigned long)caller)); \
|
||||
call[1] = to_jalr_insn((unsigned int)((unsigned long)callee - \
|
||||
(unsigned long)caller)); \
|
||||
unsigned int offset = \
|
||||
(unsigned long) callee - (unsigned long) caller; \
|
||||
call[0] = to_auipc_t0(offset); \
|
||||
call[1] = to_jalr_t0(offset); \
|
||||
} while (0)
|
||||
|
||||
#define to_jalr_insn(offset) \
|
||||
(((offset & JALR_OFFSET_MASK) << JALR_SHIFT) | JALR_BASIC)
|
||||
#define to_jalr_ra(offset) \
|
||||
(((offset & JALR_OFFSET_MASK) << JALR_SHIFT) | JALR_RA)
|
||||
|
||||
#define to_auipc_insn(offset) \
|
||||
#define to_auipc_ra(offset) \
|
||||
((offset & JALR_SIGN_MASK) ? \
|
||||
(((offset & AUIPC_OFFSET_MASK) + AUIPC_PAD) | AUIPC_BASIC) : \
|
||||
((offset & AUIPC_OFFSET_MASK) | AUIPC_BASIC))
|
||||
(((offset & AUIPC_OFFSET_MASK) + AUIPC_PAD) | AUIPC_RA) : \
|
||||
((offset & AUIPC_OFFSET_MASK) | AUIPC_RA))
|
||||
|
||||
#define make_call_ra(caller, callee, call) \
|
||||
do { \
|
||||
unsigned int offset = \
|
||||
(unsigned long) callee - (unsigned long) caller; \
|
||||
call[0] = to_auipc_ra(offset); \
|
||||
call[1] = to_jalr_ra(offset); \
|
||||
} while (0)
|
||||
|
||||
/*
|
||||
* Let auipc+jalr be the basic *mcount unit*, so we make it 8 bytes here.
|
||||
|
||||
@ -18,6 +18,7 @@ static __always_inline bool arch_static_branch(struct static_key * const key,
|
||||
const bool branch)
|
||||
{
|
||||
asm_volatile_goto(
|
||||
" .align 2 \n\t"
|
||||
" .option push \n\t"
|
||||
" .option norelax \n\t"
|
||||
" .option norvc \n\t"
|
||||
@ -39,6 +40,7 @@ static __always_inline bool arch_static_branch_jump(struct static_key * const ke
|
||||
const bool branch)
|
||||
{
|
||||
asm_volatile_goto(
|
||||
" .align 2 \n\t"
|
||||
" .option push \n\t"
|
||||
" .option norelax \n\t"
|
||||
" .option norvc \n\t"
|
||||
|
||||
Some files were not shown because too many files have changed in this diff Show More
Loading…
Reference in New Issue
Block a user