Currently, firmware sends WMI_WLAN_FREQ_AVOID_EVENTID with set
of frequency ranges to be avoided when it finds LTE operating
around those frequencies. Host driver marks these frequencies
as unsafe and doesn't operate in SAP/P2P-GO mode.
There is a new requirement where SAP can be allowed to operate
in unsafe channels when below conditions are met,
1. Firmware advertises the capability fix_channel_priority in
WMI_COEX_FIX_CHANNEL_CAPABILITIES through ext2 event.
2. SAP is started in a fixed channel.
Fetch the capability fix_channel_priority sent by firmware and
cache it in wlan_psoc_host_service_ext2_param to support
this feature. Add APIs to cache value received from firmware in
psoc_info->info.service_ext2_param.sap_coex_fixed_chan_support
and to fetch the same.
Change-Id: I8ceb501240bc86d6b004446f9927f4402c487203
CRs-Fixed: 3381399
- Replace T2LM array in wlan_t2lm_context structure with established_t2lm
and upcoming_t2lm structures
- Mapping switch time is different for each AP vdevs. Hence, store the
value in vdev_mlme_proto_ap structure.
- Fix a few issues seen in mapping switch time expiry and expected duration
expiry.
Change-Id: Id69badc3f4bf5e5e741691348488369008ffc4e9
CRs-Fixed: 3369279
Special vap on AR9887 (ap_monitor) is used as both monitor and
AP mode. During channel change on DFS channels, vap is not up till DFS
CAC timer completes and hence cfg80211tool is not releasing the
rtnl_lock.
For Scan radio, CAC timer can be disabled on DFS channels.
Change-Id: I6142325892401e3a374760179ec7e4e206296f33
CRs-Fixed: 3341288
Add support for mlo groups in mlo soc/link setup and teardown
sequence participating in mlo.
Change-Id: I2b431b0ee1e5816b92ad183b52ad2998eb5bb46c
CRs-Fixed: 3343170
Initialize Spectral Scan detector ID to Spectral mode table for
QCA5332. Detector ID 1 and 2 are not supported for QCA5332.
CRs-Fixed: 3366784
Change-Id: I7fe9b53819c649455a67957827e4f900e39257e0
Mark srng_initialized to true when the DBR ring memory
allocation is completed.
Change-Id: Iacb4d5ac884bb575ad4b98201280527521906e63
CRs-Fixed: 3355169
Add ucfg and wmi changes to support for green ap low latency
power mode enable/disable command.
Change-Id: Ib9112e384c8354f1eff0f15610301225d51ef3ac
CRs-Fixed: 3265649
1. Change the names of parameters and functions related
to direct switch feature from ppe to ppeds
2. Remove the unused ppe_release_ring
Change-Id: I5a95b1273e338f354903af98158578ac65758a8a
CRs-Fixed: 3345097
Host and FW have agreement about using fixed pdev id for CFR on HMT.
Since it's different to legacy chip for concurrency case or get pdev
id base band.
Change-Id: I2b16876244cf8988e8855752844917fbf0154f54
CRs-Fixed: 3312489
To assist the Host in ML reconfiguration element construction for probe
responses, FW sends MLO link removal information as part of the MGMT Rx
event containing the corresponding probe request. This information is an
array of TLVs, one TLV for each link that is undergoing link removal from
the MLD for which this probe request is intended. The TLV carries the link
removal TBTT countdown value maintained by the FW for that link.
Add support to extract the same.
CRs-Fixed: 3335361
Change-Id: I16c6791a443ddb166da596d404a52ff2a38da291
WMI_MLO_LINK_REMOVAL_EVENTID will be sent by FW to update the Host on the
progress of the link removal operation. Add support to process this event.
Change-Id: I0c4d5b047cf062b421380f85717fac5a9bdea9c2
CRs-Fixed: 3334950
WMI_MLO_LINK_REMOVAL_CMDID is to be sent by the Host to initiate the
removal procedure for a given link from its MLD. This command will be sent
on the impacted link only. Add support to populate and send this command.
Change-Id: I8485d8c8897bb2bb891d50546d5fbfac2a69a4ce
CRs-Fixed: 3314430
Add API to parse the TID-to-link mapping event ID for the AP vaps.
As part of this event,
- Update the mapping switch time TSF value in host data structures.
- When mapping switch time or expected duration expires in the FW,
update the host data structure.
Change-Id: I93232429fe5c2aa12dc4bf9f6a2f014761b7df15
CRs-Fixed: 3350697
Set default value for 'offset' to fix the compile issue
'variables may be used uninitialized'.
Change-Id: Ib8db38140463fb543b1d98f19743b3a3a7fded4c
CRs-Fixed: 3345183
When AFC event come and update 6 GHz SP channels' state and power
attribution, SAP which already started on 5 GHz or 6 GHz channel
can move in or out from SP channel, which has higher tx power limit.
SAP target channel/bandwidth is decided by ACS channel select callback
register to SAP module, which will take channel max tx power limit
into account.
After target channel/bandwidth determined, SAPs move to same target
channel/bandwidth with eCSA process. If violate any concurrency
limitation, AFC DCS process should abort.
Add AFC component id and reference id.
Change-Id: Iba6933a30c0957eabf549fd6c8442bed547e8152
CRs-Fixed: 3204172
In case of split-phy radio, both the wmacs may belong to the
same PSOC. Hence in WMI_VDEV_SET_TPC_POWER_CMDID/
WMI_SET_INIT_COUNTRY_CMDID/WMI_AFC_CMDID, instead of
fetching the wmi_handle from psoc, find the WMI handle for the
corresponding pdev on which the cmd must be sent.
CRs-Fixed: 3333857
Change-Id: Ib38b15dbda4ea83edd6341d7732addbb1a563ad2
CFG section definitions for 6 GHz low & high band for
ini configurations. These new definitions enables us to
configure the unique INI parameters for 6 GHz low and
6 GHz high band, for new solution of Split-phy in 6 GHz.
Change-Id: I1417dee90f0aebe31f24a64017d9203b74dfc886
CRs-Fixed: 3332719
Using pdev_wmi_handle instead of wmi_handle in
target_if_peer_set_ppe_default_routing
Change-Id: I7eb94d2b92078c55f2c03f4ccd57d124d3229053
CRs-Fixed: 3341573
Currently if ENABLE_HOST_TO_TARGET_CONVERSION is defined,
host pdev/vdev set params can be translated to
target pdev/vdev set params through APIs
convert_host_pdev_param_tlv,convert_host_vdev_param_tlv.
If ENABLE_HOST_TO_TARGET_CONVERSION is not defined,
host pdev/vdev set params in
common code is sent to firmware directly, which is incorrect.
Define pdev/vdev set params in such away they represents
host params on ENABLE_HOST_TO_TARGET_CONVERSION enabled and
target params on ENABLE_HOST_TO_TARGET_CONVERSION disabled.
Change-Id: I5718c76c351b2d7904d8bf8b603073ffcb0a039d
CRs-Fixed: 3321556
Add void keyword to function definitions for
ce_service_srng() and target_if_get_ctx().
Change-Id: I4d74600da82a9f13285a496a2136589b698da017
CRs-Fixed: 3336700
Add common code to configure target AFC flags:
enable_6ghz_sp_pwrmode_supp, afc_disable_timer_check,
afc_disable_request_id_check.
Remove cfg_get set is_afc_reg_noaction code, add it to psoc regulatory
private data.
Add APIs to set and get these AFC configures.
Change-Id: Idf74b245113eee18b071a7fbb92bb151cd535ce8
CRs-Fixed: 3154185
Currently, only single pd_threshold is fetched and
treated as SRG and NON-SRG pd threshold instead of
handling both threshold separately.
Fix is to get SRG and NON-SRG pd threshold from
userspace instead of single pd threshold.
Change-Id: I414843dfd08068c81531d0e96d71fb68d8bfccd1
CRs-Fixed: 3328201
A new capability bit from FW is introduced that provides
ADFS 320 MHz support information. supports_adfs_320 signifies
chainmask capability service bit if FW supports ADFS on 320 MHz
channel width. Add this capability bit(supports_adfs_320) in host.
Change-Id: I09c689658ef495d8a8707425ecc9ba922fce4d41
CRs-Fixed: 3317795
Add reg txops to fetch min_psd for punctured SP channels.
min_psd is computed from afc response. Using the min_psd power value,
EIRP is computed for the non-punctured BW using the formula
EIRP = PSD + 10 * log10(non-punctured BW).
Add an entry in bw_to_10log10_map for all possible non-punctured
bandwidth.
CRs-Fixed: 3329625
Change-Id: I79707cb233640342c521e41e9c4d776e121c1d6d
This change is to populate the phase delta for the valid
chains as per rx_chainmask for scan radio in special
vap mode.
Change-Id: I3ff9a928d93b0e81221b2bf9a515c63150f04272
CRs-Fixed: 3316528
Log the time stamp corresponding to the start of processing
of multi vdev restart response event.
CRs-Fixed: 3308918
Change-Id: Ia00923b3a1033097429d3856047a4b639408aab8
In the current implementation, the Direct DMA completion event is getting
processed in the tasklet context. When the Direct DMA events land on the
same processor core as the one used by the WLAN data path events, the
Direct DMA events can pre-empt the data path events as the datapath
events usually run in NAPI context. This could impact the data path
throughput when there is a high volume of frequent Direct DMA events. To
fix this, Direct DMA events can be run in work queue context based on
user configuration. Add support for the same.
Change-Id: I1a89b185c6765addc7ee725e9324025f0318d9ed
CRs-Fixed: 3276157
Fix incompatible function pointer assignment.
Define a wrapper around mc timer callbacks to
make them compatible with standard scheduler
message callback function signatures.
Change-Id: I07829680d1758ccbd53e8b1fe10b0e30e100a2c6
CRs-Fixed: 3305719
Add input_punc_bitmap to struct ch_params.
Add input puncture bitmap to regualtory channel search APIs.
The non-SP channels will be punctured by ACS module so that AP
can come up in highest possible BW in Standard Power mode
with the given primary frequency. These punctured channels are not
validated (whether supported in the given power mode of operation) by
the regulatory.
CRs-Fixed: 3278013
Change-Id: I56b0495be902fd92fc6da26e1007d60f930ba687
Add target_if support to set EIRP as the preferred power in the
WMI_VDEV_SET_TPC_CMDID to the target.
Change-Id: I77850ce93a3561c9765b8d70ae84e940b2bbf4d4
CRs-Fixed: 3307372
This fixes a scheduler_msg CFI failure for function
target_if_vdev_mgr_del_rsp_post_cb().
Change-Id: I296fdfca228799de2d84c6c41eb7cd656d8f3c52
CRs-Fixed: 3316600
The RX REO functionality has numerous misspellings of "forwarded",
including multiple identifiers. Fix these to use the correct spelling.
Change-Id: Idc4e66e7356b978742fea30ae7ef0c9498c4f938
CRs-Fixed: 3313839
Send BSS color and partial BSSID bitmap to fw when SR
enable is sent to FW, so that FW can classify the srg
and non-srg colors.
Change-Id: I44711fd7e7cc05867d042a04e783ae29b04b388a
CRs-Fixed: 3304796
Handle SR enable vendor command as part of which
send PD threshold value provided by userspace
check the range of the provided threshold,
if threshold lies with in SRG or NON-SRG
range then provide the threshold sent by
userspace else send the MAX of SRG and NON-SRG
offset advertised by AP.
Change-Id: I428a933cc324446fdb4f18f535f1b78228d504fa
CRs-Fixed: 3304779
1.This change fixes the use of uninitialized
variable in host driver.
2.Adds NULL check for num_psocs in mlo_peer_calculate_avg_rssi to
avoid undefined behaviour.
Change-Id: Ifbfef42b5930dfe15736a75a74e81155c5f1fbce
CRs-Fixed: 3297794
Current issue:
During disconnect host sends RSO STOP command to FW
and expects a response from FW before continuing disconnect.
If roaming is disabled (from supplicant or due to race condition)
before sending RSO STOP cmd then FW does not respond to the request
and host will assert.
Solution:
To handle this case after rso timer stop expiry continue with
disconnect and clean up the rso state.
Change-Id: Iac7b25d881702b87f946fe0ecfba02b1d806f06b
CRs-Fixed: 3301394
While generating the scan entry for TX VAP, the decision to
strip MBSSID IE from the TX VAP beacon, will be taken if the
platform supports 11BE.
CRs-Fixed: 3300515
Change-Id: Ie45da7a02a2811172b2403d5fd1bc4b9271432d5
- target_if layer was calling UMAC layer wifi_pos_get_rx_ops(). This was
leading to compilation errror in WIN platform. Hence, added target_if
layer API target_if_wifi_pos_get_rx_ops().
- WMI_RX_SERIALIZER_CTX is used to register PASN peer create and delete.
WIN platform does not use the above context. Hence, use WMI_RX_UMAC_CTX
for WIN and WMI_RX_SERIALIZER_CTX for MCC.
- WIFI_POS rx_ops callbacks are registered in target_if layer. But, these
callbacks are called by UMAC component. Hence, move this registration
function to UMAC layer.
- Add an API to convert host PASN peer type value to target defined value.
Change-Id: I2a262121f959c2343e88158b94468d104b9e164c
CRs-Fixed: 3289852
Any error during ext/ext2 processing should stop normal init
path and return error. Without this, wrong values are passed
to firmware in WMI init which result in firmware assert.
Add proper handling to take care of failures during svc ready
message processing
Change-Id: Id22714a983d1dc2fe7300a178933cd05bf870a55
CRs-Fixed: 3290131
