Those lines have two copies.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Avoid twl6040-codec PLL reconfiguration when not needed
mfd: Store twl6040-codec mclk configuration
Some devices (iwl5100) cannot connect to zd1211rw based AP. It appears that
zd1211 firmware messes up duration_id field if it is not set to zero by driver.
Sniffing traffic shows that zd1211 is transmitting frames with duration_id bits
14 and 15 set and other bits appearing random. Setting duration_id at driver to
zero results zd1211 outputting sane duration_id. This means that firmware is
setting correct values itself and expects duration_id to be zero in first
place.
Looking at vendor driver shows that only PSPoll frames have duration_id set by
driver, for other frames duration_id left zero.
Original bug-report and attached patch at:
http://sourceforge.net/mailarchive/message.php?msg_id=28759111
Reported-by: Tomas Vanek <Tomas.Vanek@fbl.cz>
[modified original patch from bug-report, added check for pspoll frame]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
8<----------------------------------------------------------------------
From: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Date: Wed, 16 Nov 2011 09:33:50 +0100
Subject: [PATCH] net: enable TC35815 for MIPS again
TX493[8,9] MIPS SoCs support 2 Ethernet channels of type TC35815
which are connected to the internal PCI controller.
And JMR3927 MIPS board has a TC35815 chip on board.
These dependencies were lost on movement to drivers/net/ethernet/toshiba.
Signed-off-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: stable@vger.kernel.org [3.2+]
Signed-off-by: David S. Miller <davem@davemloft.net>
When this GETHER controller received a large frame (about 1800 bytes
or more), skb_over_panic() happened. This is because the previous
driver set the RFLR to 0x1000 (4096 bytes) and the skb allocate size
is smaller than 4096 bytes. So, the controller accepted such a frame.
The controller can discard a large frame by the RFLR setting.
So, the patch modifies the value of RFLR to mtu + ETH_HLEN +
VLAN_HLEN + ETH_FCS_LEN.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate memory for 'new_data' with kmalloc(). If we get the memory
we then try to build_skb() and if that should fail (which it can) we
do not enter 'if (likely(skb)) {' and actually use 'new_data' but
instead fall through to the 'drop:' label and end up returning from
the function without ever assigning 'new'data' to anything or freeing
it. That leaks the memory allocated to 'new_data'.
This patch fixes the memory leak by doing a kfree(new_data) in the
case where build_skb() fails (or where allocation of 'new_data' itself
fails, but in taht case it's just a harmless kfree(NULL)).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, with PCI/ISA/MCA/CCW all set to n and PCMCIA set to m
setting TR to y will set LLC to m, with very unpleasant results -
net/802/psnap gets picked into obj-y, resulting in the kernel
that won't link - psnap calls functions from llc. The cause,
AFAICS, is that kconfig gets rev_dep for LLC containing
|| TR && (deps for TR)
and even though TR is boolean, both LLC and PCMCIA are tristate
and that thing becomes || y && (n || m), i.e. || m. The reason
for dependency on PCMCIA is that when none of PCI, ISA, MCA, CCW
or PCMCIA is set there'll be no tokenring drivers, so there's no
point building tokenring core. Proper fix probably belongs in
kconfig (we need strict and, such that y <strict_and> m would be
y, so that rev_deps added for tristate selected by bool would
use that instead of &&; we'd have || TR <strict_and> (deps for TR)
in this case), but it's a rather intrusive change. There's an
easy workaround in case of TR -> LLC select, namely to have a def_bool y
symbol sitting under if TR and have that symbol selecting LLC.
Kudos to johill for suggesting that one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by several people...
The code in rx_clean was panic'ing so revert
commit d0249e44432aa0ffcf710b64449b8eaa3722547e.
Will redo DMA mapping checks as new patches for a later release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Analogically to d7cb3dbd1 ("HID: wacom: Fix invalid power_supply_powers
calls"), fix also the same occurence in wiimote driver.
Reported-by: przemo@firszt.eu
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removed the following:
* irrelevant argument 'barrier' of mtip_hw_submit_io()
* unused member 'eh_active' of struct driver_data
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes a bug in target-core where unsupported WRITE_SAME ops
from a target_check_write_same_discard() failure was incorrectly
returning CHECK_CONDITION w/ TCM_INVALID_CDB_FIELD sense data.
This was causing some clients to not properly fall back, so go ahead
and use the correct TCM_UNSUPPORTED_SCSI_OPCODE sense for this case.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use IP_FREEBIND socket option so that iscsi portal configuration with
explicit IP addresses can happen during boot, before network interfaces
have been assigned IPs.
This is especially important on systemd based Linux boxes where system
boot happens asynchronously and non-trivial configuration must be done
to get targetcli.service to start synchronously after the network is
configured.
Reference:
http://lists.fedoraproject.org/pipermail/devel/2011-October/158025.html
Signed-off-by: Dax Kelson <dkelson@gurulabs.com>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: "Andy Grover" <agrover@redhat.com>
Cc: "Lennart Poettering" <lennart@poettering.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Requesting to many bvecs upsets bio_alloc_bioset, so limit the number we ask
for to the amount it can handle.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These are root only and we're not likely to hit the problem in practise,
but it makes the static checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fixes this error after a recent nfs cleanup:
drivers/target/iscsi/iscsi_target_configfs.c: In function 'lio_target_call_addnptotpg':
drivers/target/iscsi/iscsi_target_configfs.c:214:3: error: implicit declaration of function 'in6_pton' [-Werror=implicit-function-declaration]
drivers/target/iscsi/iscsi_target_configfs.c:239:3: error: implicit declaration of function 'in_aton' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The block layer keeps q->limits.discard_granularity in bytes, but iblock
(and the SCSI Block Limits VPD page) keep unmap_granularity in blocks.
Report the correct value when exporting block devices by dividing to
convert bytes to blocks.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in target_submit_cmd() where the failure path
for transport_generic_allocate_tasks() made a direct call to
transport_send_check_condition_and_sense() and not calling the
final target_put_sess_cmd() release callback.
For transport_generic_allocate_tasks() failures, use the proper call to
transport_generic_request_failure() to handle kref_put() along
with potential internal queue full response processing.
It also makes transport_lookup_cmd_lun() failures in
target_submit_cmd() use transport_send_check_condition_and_sense() and
target_put_sess_cmd() directly to avoid se_cmd->se_dev reference in
transport_generic_request_failure() handling.
Finally it drops the out_check_cond: label and use direct reference for
allocate task failures, and per-se_device queue_full handling is
currently not supported for transport_lookup_cmd_lun() failure
descriptors due to se_device dependency.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Retval not very useful, and may even be harmful. Once submitted, fabrics
should expect a sense error if anything goes wrong. All fabrics checking
of this retval are useless or broken:
fc checks it just to emit more debug output.
ib_srpt trickles retval up, then it is ignored.
qla2xxx trickles it up, which then causes a bug because the abort goto
in qla_target.c thinks cmd hasn't been sent to target.
Just returning nothing is best.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
WindowsXP+BOT issues a MODE_SENSE request with page 0x1c which is not
suppoerted by target. Target rejects that command with
TCM_INVALID_CDB_FIELD, so far so good. On BOT I can't send the SENSE
response back, instead I can only reply that an error occured. The next
thing happens is a REQUEST_SENSE request with 18 bytes length. Since the
check here is more than 18 bytes I have to NACK that request as well.
This is not really required: We check for some additional room, but we
never use it. The additional length is set to 0xa so the total length is
0xa + 8 = 18 which is fine with my 18 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It was originally missed in the __devinit/__devexit annotations.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
1/ If a resync is aborted we should record how far we got
(recovery_cp) the last request that we know has completed
(->curr_resync_completed) rather than the last request that was
submitted (->curr_resync).
2/ When a resync aborts we still want to update the metadata with
any changes, so set MD_CHANGE_DEVS even if we 'skip'.
Signed-off-by: NeilBrown <neilb@suse.de>
Straight forward bug fixes in this branch. A couple of x86 gpio drivers
missing spinlock initialization, an API change fixup for the samsung driver
and a name typo fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WQ/Y
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
GPIO fixes for v3.3-rc2
Straight forward bug fixes in this branch. A couple of x86 gpio drivers
missing spinlock initialization, an API change fixup for the samsung driver
and a name typo fix.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add missing spin_lock_init in gpio-ml-ioh driver
gpio: Add missing spin_lock_init in gpio-pch driver
gpio: samsung: adapt to changes in gpio specifier translator function declaration
Correct bad gpio naming
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQEcBAABAgAGBQJPLedwAAoJEANmWzN1g3l3F18IAJvV8cvTBDr/OV5wmEHx4v7t
s9l7wfXop2ilsNoAT8mdLwa6ilwatG9k9UhzsF8a2nUR1rNAWA9SFc2v6kLCIZpN
SVQzh9260X5jrRiUn7dKpLwwxDbepcvHFbpei9Xi/ON97ZjUnHEk27tf/s6MI8ad
EvCCJR+Lsw1ara6ZX+kQqznUME46dPZA6A5rxXFbRv8QTIe8++f+KSdXWBt8r3yK
pDfdEGyYwkDoqjUBv2EZ/XMCQdjmdgU9NRExKHJdOyHnea+0RbUik1viuXm7JNQV
Rd9DtC3vjq8qxCLBhJ1Ay5K8TmAbrgAGGjCo98mNY8D0F9NXL4sfyPW7qxCEa3E=
=tYxf
-----END PGP SIGNATURE-----
Merge tag 'hwmon-fixes-for-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
One patch to fix fan detection on NCT6776F.
* tag 'hwmon-fixes-for-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (w83627ehf) Fix number of fans for NCT6776F
It is never correct to use intel_crtc->bpp in intel_dp_link_required,
so instead pass an explicit bpp in to this function. This patch
only supports 18bpp and 24bpp modes, which means that 10bpc modes will
be computed incorrectly. Fixing that will require more extensive
changes, and so must be addressed separately from this bugfix.
intel_dp_link_required is called from intel_dp_mode_valid and
intel_dp_mode_fixup.
* intel_dp_mode_valid is called to list supported modes; in this case,
the current crtc values cannot be relevant as the modes in question
may never be selected. Thus, using intel_crtc->bpp is never right.
* intel_dp_mode_fixup is called during mode setting, but it is run
well before ironlake_crtc_mode_set is called to set intel_crtc->bpp,
so using intel_crtc-bpp in this path can only ever get a stale
value.
Cc: Lubos Kolouch <lubos.kolouch@gmail.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42263
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44881
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: camalot@picnicpark.org (Dell Latitude 6510)
Tested-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
mlx4_en_prepare_rx_desc does not correctly clean up after it finds an
allocation failure. It should unmap a page before calling put_page, but
it only calls the later.
This bug would prevent a device removal using hotplug after setting the
device MTU to 9000 and opening the network interface. After the fix, we
still see the allocation failure with MTU 9000, but we are able to
remove the device.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After opening the network interface, Mellanox ConnectX device cannot be
removed by hotplug because it has not properly unmapped all DMA memory.
It happens that mlx4_en_activate_rx_rings overrides the variable that
keeps the size of the memory mapped.
This is fixed by passing to mlx4_en_destroy_rx_ring the same size that is
given to mlx4_en_create_rx_ring.
After applying this patch, hot unplugging the device works after opening
the interface.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The brcmsmac driver is now using the bcma SPROM CRC check, which does
not recognize all chipsets that were functional prior to the switch. In
particular, the current code bails out on odd CRC errors in recent
Macbooks. This patch ignores those errors, with the argument that an
unrecognized SPROM should be treated similarly to a non-existing one.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use port number for correct steering (list per port).
Before the fix all steering entries (for both physical ports)
were managed in first port structures, so we had leakage of resources
for port 2.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MLX4_DEV_CAP_FLAG_VEP_UC_STEER for unicast_promisc_add/remove
Unicast entries were managed in wrong data structures.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform cleanup also in non-master flow.
The VFs use communication channel as well.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit adb5066 "ath9k_hw: do not apply the 2.4 ghz ack timeout
workaround to cts" reduced the hardware CTS timeout to the normal
values specified by the standard, but it turns out while it doesn't
need the same extra time that it needs for the ACK timeout, it
does need more than the value specified in the standard, but only
for 2.4 GHz.
This patch brings the CTS timeout value in sync with the initialization
values, while still allowing adjustment for bigger distances.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b4a82a0 "ath9k_hw: fix interpretation of the rx KeyMiss flag"
fixed the interpretation of the KeyMiss flag for keycache based lookups,
however WEP encryption uses a static index, so KeyMiss is always asserted
for it, even though frames are decrypted properly.
Fix this by clearing the ATH9K_RXERR_KEYMISS flag if no keycache based
lookup was performed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Laurent Bonnans <bonnans.l@gmail.com>
Reported-by: Jurica Vukadin <u.ra604@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If driver load is failed, sometimes few pointers may remain
uninitialized ex. priv->wdev, priv->netdev, adapter->sleep_cfm
This will cause NULL pointer dereferance while unloading the
driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
power_supply_powers calls added in 35b4c01e2 ("power_supply: add "powers" links
to self-powered HID devices") have to be called after power device is created.
This patch also fixes the second call - it has to be "ac" instead of "battery"
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sync with Linus' tree. This is necessary to have a base for
patch that fixes commit 35b4c01e29b ("power_supply: add "powers"
links to self-powered HID devices") which went in through Anton's
tree.
"nframes" comes from the user and "nframes * CD_FRAMESIZE_RAW" can wrap
on 32 bit systems. That would have been ok if we used the same wrapped
value for the copy, but we use a shifted value. We should just use the
checked version of copy_to_user() because it's not going to make a
difference to the speed.
Cc: stable@vger.kernel.com
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename static struct pci_driver pch_spi_pcidev to
pch_spi_pcidev_driver to get rid of warnings from modpost checks.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The spi-s3c64xx driver is also used on Exynos4 so update the dependency
to enable build on those platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[grant.likely: relax depends to ARCH_EXYNOS instead of ARCH_EXYNOS4]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Initially diagnosed on Ubuntu 11.04 with kernel 2.6.38.
velocity_close is not called during a suspend / resume cycle in this
driver and it has no business playing directly with power states.
Signed-off-by: David Lv <DavidLv@viatech.com.cn>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCT6776F can select fan input pins for fans 3 to 5 with a secondary set of
chip register bits. Check that second set of bits in addition to the first set
to detect if fans 3..5 are monitored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPLYzVAAoJEIwa5zzehBx3QSMP/17+6JYJEnzNgZAnrCNm03EK
4f72pLIh6SSKn85jrq+mYlUorakUhlkF26G7+IyYz96YsvvEjrp8mKqlnate4Svv
veROfNIa12AifX6H/0hr9xiRJLK+RLz933HAywh24x9GeKBAjoS72EcZRmThZWJ9
RssfzAXAUbAfwYJyczcEpLOLkg7HJIAx5w7mQLh/hkhWkDKAugO8z1tSKESN98F3
HJtSKE84Xg17y0c1SRoBTV3npSf3D2RptSX0r7H/nT3dpM1lSjoPvawtqdGf+ibT
plHmRY75ebGEq18CHOl177YXPq0iUyfCDLqsu/nbcTtWoY/Cdfdj5gmMHuCYItcY
8JJ758KUIJeHBpjbfeFbAPXJwa2FTnhgG9IQmCWuO47mquBCAi2TCWMmyNi1+kuZ
PB+RkoU8O99bIwI+9vza1apVjjqx7rW6+9IS56KXkKYq6FkSbkvtpuveYvkvuboT
D9o9GKmLL2Z4qE0XG7jsFi7RU1dymTaWow4chyx/iVvNvZnA/Yb9z1CmbydsyLV3
ND1e7Tt49OIjy764Vw1KNmnIhd2joFoqF4jcw/+ID+Hy7cFSuBjjIR6TkZrqYjNf
FhgqrRTl4iIw9zIroAJFuWOQOe82vxDDRVTe/7S7SrhvF5nTDF0AqHmeenBo6cLM
0CfOwbRxbpgXfDpaHbH9
=tFsG
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
arm-soc fixes for 3.3-rc
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcmring: fix build failure in mach-bcmring/arch.c
ARM: bcmring: remove unused DMA map code
ARM: davinci: update mdio bus name
ARM: OMAP2+: arch/arm/mach-omap2/smartreflex.c: add missing iounmap
ARM: OMAP2+: arch/arm/mach-omap2/devices.c: introduce missing kfree
ARM: OMAP: fix MMC2 loopback clock handling
ARM: OMAP: fix erroneous mmc2 clock change on mmc3 setup
ARM: OMAP2+: GPMC: fix device size setup
ARM: OMAP2+: timer: Fix crash due to wrong arg to __omap_dm_timer_read_counter
ARM: OMAP3: hwmod data: register dss hwmods after dss_core
ARM: OMAP2/3: PRM: fix missing plat/irqs.h build breakage
ARM: OMAP2+: io: fix compilation breakage on 2420-only configs
ARM: OMAP4: hwmod data: Add names for DMIC memory address space
ARM: OMAP3: hwmod data: add SYSC_HAS_ENAWAKEUP for dispc
ARM: OMAP2+: hwmod data: split omap2/3 dispc hwmod class
ARM: davinci: DA850: remove non-existing pll1_sysclk4-7 clocks
ARM: OMAP2: fix regulator warnings
ARM: OMAP2: fix omap3 touchbook kconfig warning
i2c: OMAP: Fix OMAP1 build error
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
i.MX SDMA: Fix burstsize settings
ARM: mach-shmobile: both USB DMAC instances on sh7372 are slave-only
dma: sh_dma: not all SH DMAC implementations support MEMCPY
at_hdmac: bugfix for enabling channel irq
dmaengine: fix missing 'cnt' in ?: in dmatest
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk8s6HsACgkQdwG7hYl686MIiACgxpNoUWFvq8z+2UGXxsLnNrio
hhcAn31H7TY3KUuIQBo4CqG2dEjNwpCw
=DRWp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.3' of git://git.infradead.org/~dwmw2/mtd-3.3
- Fix a regression in 16-bit Atmel NAND flash which was introduced in 3.1
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
* tag 'for-linus-3.3-20120204' of git://git.infradead.org/~dwmw2/mtd-3.3:
Revert "mtd: atmel_nand: optimize read/write buffer functions"
mtd: fix MTD suspend
jffs2: do not initialize variable unnecessarily
mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23
mtd: nand: fix typo in comment
This reverts commit fb5427508abbd635e877fabdf55795488119c2d6.
The reason is that it breaks 16 bits NAND flash as it was reported by
Nikolaus Voss and confirmed by Eric Bénard.
Nicolas Ferre <nicolas.ferre@atmel.com> alco confirmed:
"After double checking with designers, I must admit that I misunderstood
the way of optimizing accesses to SMC. 16 bit nand is not so common
those days..."
Reported-by: Nikolaus Voss <n.voss@weinmann.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.1+]
KDFONTOP(GET) currently fails with EIO when being run in a 32bit userland
with a 64bit kernel if the font width is not 8.
This is because of the setting of the KD_FONT_FLAG_OLD flag, which makes
con_font_get return EIO in such case.
This flag should *not* be set for KDFONTOP, since it's actually the whole
point of this flag (see comment in con_font_set for instance).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Arthur Taylor <art@ified.ca>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
