Function mlx4_en_set_channels() stops running ports before performing the
requested action. In that case local variable 'port_up' is set so that the
port is restarted at the end of the function, however, in case the port was
not stopped, variable 'port_up' is left uninitialized and the behaviour is
undetermined. Detected by Coverity - CID 751497.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These "return 0;" uses seem wrong as there are
rc variables where error return values are set
but unused.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can end up with a freshly allocated tx_curr_skb with no frames
in it. In this case it does not make any sense to start the timer.
This avoids the timer periodically trying to start tx when there
is nothing in the queue.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling netif_carrier_{on,off} is sufficient. There is no need
to duplicate the carrier state in a driver specific flag.
Acked-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of devices request much larger buffers than reasonable. This
cause real problems for users of hosts with limited resources.
Reducing the default buffer size to 16kB for such devices is
a reasonable trade-off between allowing them to aggregate traffic
and avoiding memory exhaustion on resource restrained hosts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have an idea of the effects of the protocol coalescing
it's useful to have some counters showing the different
aspects.
Due to the asymmetrical usbnet interface the netdev
rx_bytes counter has been counting real received payload,
while the tx_bytes counter has included the NCM/MBIM
framing overhead. This overhead can be many times the
payload because of the aggressive padding strategy of
this driver, and will vary a lot depending on device
and traffic.
With very few exceptions, users are only interested in
the payload size. Having an somewhat accurate payload
byte counter is particularly important for mobile
broadband devices, which many NCM devices and of course
all MBIM devices are. Users and userspace applications
will use this counter to monitor account quotas.
Having protocol specific counters for the overhead, we are
now able to correct the tx_bytes netdev counter so that
it shows the real payload
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pad frames larger than X to maximum size for devices which
don't need a ZLP after maximum sized frames. This allows the
device to optimize its transfers for one fixed buffer size.
X was arbitrarily set at 512 bytes regardless of real buffer
maximum, causing extreme overheads due to excessive padding of
larger tx buffers. Limit the padding to at most 3 full USB
packets, still allowing the overhead to payload ratio of 3/1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many newer NCM and MBIM devices will request a maximum tx
datagram count which is much smaller than our hard-coded
absolute max. We can reduce the overhead without sacrificing
any of the simplicity for these devices, by simply using the
true negotiated count in when calculated the maximum NTH and
NDP header sizes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datagram coalescing is an integral part of the NCM and MBIM
protocols, intended to reduce the interrupt load primarily
on the device end of the USB link. As with all coalescing
solutions, there is a trade-off between buffering and
interrupts.
The current defaults are based on the assumption that device
side buffers should be the limiting factor. However, many
modern high speed LTE modems suffers from buffer-bloat,
making this assumption fail. This results in sub-optimal
performance due to excessive coalescing. And in cases where
such modems are connected to cheap embedded hosts there is
often severe buffer allocation issues, giving very noticeable
performance degradation .
A start on improving this is going from build time hard
coded limits to per device user configurable limits. The
ethtool coalescing API was selected as user interface
because, although the tuned values are buffer sizes, these
settings directly control datagram coalescing.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish the rx_max/tx_max setup by flushing buffers and
informing usbnet about the changes. This way, the settings
can be modified while the netdev is up and running.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have split out the part of the device setup
which MUST be done with the data interface in altsetting 0,
we can delay the rest of the initialization. This allows us
to move some of post-init buffer size config from bind to
the appropriate setup function.
The purpose of this refactoring is to collect all code
adjusting the rx_max and tx_max buffers in one place, so
that it is easier to call it from multiple call sites.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the parts of setup dealing with device initialization from
parts just setting defaults for attributes which might be
changed after initialization.
Some commands of the device initialization are only allowed when
the data interface is in its disabled altsetting, so we must
separate them out of we are to allow rerunning parts of setup.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the part of setup dealing with updating the rx_max
and tx_max buffer sizes so that this code can be reused for
dynamically updating the limits.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALB/TLB learning packets use all vlans configured on top
of the bond. This ends up being incorrect if we have a stack
of vlans on top of the bond. ALB/TLB should only use
first level/outer most vlans in its announcements.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit fbd929f2dce460456807a51e18d623db3db9f077
bonding: support QinQ for bond arp interval
the arp monitoring code allowed for proper detection of devices
stacked on top of vlans. Since the above commit, the
code can still detect a device stacked on top of single
vlan, but not a device stacked on top of Q-in-Q configuration.
The search will only set the inner vlan tag if the route
device is the vlan device. However, this is not always the
case, as it is possible to extend the stacked configuration.
With this patch it is possible to provision devices on
top Q-in-Q vlan configuration that should be used as
a source of ARP monitoring information.
For example:
ip link add link bond0 vlan10 type vlan proto 802.1q id 10
ip link add link vlan10 vlan100 type vlan proto 802.1q id 100
ip link add link vlan100 type macvlan
Note: This patch limites the number of stacked VLANs to 2,
just like before. The original, however had another issue
in that if we had more then 2 levels of VLANs, we would end
up generating incorrectly tagged traffic. This is no longer
possible.
Fixes: fbd929f2dce460456807a51e18d623db3db9f077 (bonding: support QinQ for bond arp interval)
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Patric McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the introduction of of_phy_register_fixed_link(), this patch
introduces fixed link support in the mvneta driver, for Marvell Armada
370/XP SOCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing fixed_phy_add() function has several drawbacks that
prevents it from being used as is for OF-based declaration of fixed
PHYs:
* The address of the PHY on the fake bus needs to be passed, while a
dynamic allocation is desired.
* Since the phy_device instantiation is post-poned until the next
mdiobus scan, there is no way to associate the fixed PHY with its
OF node, which later prevents of_phy_connect() from finding this
fixed PHY from a given OF node.
To solve this, this commit introduces fixed_phy_register(), which will
allocate an available PHY address, add the PHY using fixed_phy_add()
and instantiate the phy_device structure associated with the provided
OF node.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the fixed_phy_add() function was taking as argument
'phy_id', which was used both as the PHY address on the fake fixed
MDIO bus, and as the PHY id, as available in the MII_PHYSID1 and
MII_PHYSID2 registers. However, those two informations are completely
unrelated.
This patch decouples them. The PHY id of fixed PHYs is hardcoded to be
0x0. Ideally, a really reserved value would be nicer, but there
doesn't seem to be an easy of making sure a dummy value can be
assigned to the Linux kernel for such usage.
The PHY address remains passed by the caller of phy_fixed_add().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pch_gbe driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When umac_enable_set() is used to disable the UniMAC receiver or
transmitter, we need to make sure that we wait for a full-sized packet
to be processed because the UniMAC hardware stops on a packet boundary,
not immediately.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_unmap_single() was called with dma_unmap_len(cb, dma_len),
unfortunately we failed to assign this length field in
bcm_sysport_rx_refill() or bcm_sysport_alloc_rx_bufs() using
dma_unmap_len_set().
This causes packet contents corruption because are we not invoking the
cache invalidation routines with the proper length. Fix this by using
the full RX buffer size (RX_BUF_LENGTH) because the mappings for the RX
bufers are created with that size.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They're verifying the same thing (except of IFF_UP, which is implied for
netif_running(), which is also a prerequisite).
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, remove the IFF_UP verification cause we can't be netif_running() with
being also IFF_UP.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, use standard IP primitives to check the address.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name a bit to better reflect its scope, and update some
comments. Two functions added - one which takes bond as a param and the
other which takes the mode.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, change its name to better reflect its scope, and skip the "no"
part.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, make it accept bonding as a parameter and change the name a bit to
better reflect its scope.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's used only in an inline function and is useless.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the NAPI budget was not all used, xenvif_poll() would call
napi_complete() /after/ enabling the interrupt. This resulted in a
race between the napi_complete() and the napi_schedule() in the
interrupt handler. The use of local_irq_save/restore() avoided by
race iff the handler is running on the same CPU but not if it was
running on a different CPU.
Fix this properly by calling napi_complete() before reenabling
interrupts (in the xenvif_napi_schedule_or_enable_irq() call).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-05-15
Please pull this batch of fixes for the 3.15 stream...
For the mac80211 bits, Johannes says:
"One fix is to get better VHT performance and the other fixes tracing
garbage or other potential issues with the interface name tracing."
And...
"This has a fix from Emmanuel for a problem I failed to fix - when
association is in progress then it needs to be cancelled while
suspending (I had fixed the same for authentication). Also included a
fix from myself for a userspace API problem that hit the iw tool and a
fix to the remain-on-channel framework."
For the iwlwifi bits, Emmanuel says:
"Alex fixes the scan by disabling the fragmented scan. David prevents
scan offload while associated, the firmware seems not to like it. I
fix a stupid bug I made in BT Coex, and fix a bad #ifdef clause in rate
scaling. Along with that there is a fix for a NULL pointer exception
that can happen if we load the driver and our ISR gets called because
the interrupt line is shared. The fix has been tested by the reporter."
And...
"We have here a fix from David Spinadel that makes a previous fix more
complete, and an off-by-one issue fixed by Eliad in the same area.
I fix the monitor that broke on the way."
Beyond that...
Daniel Kim's one-liner fixes a brcmfmac regression caused by a typo
in an earlier commit..
Rajkumar Manoharan fixes an ath9k oops reported by David Herrmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f26604fb ("net: phy: suspend phydev when going
to HALTED"), an unused PHY device will be put in a low-power mode
using BMCR_PDOWN. Some Ethernet drivers might be calling phy_start()
and phy_stop() from ndo_open and ndo_close() respectively, while
calling phy_connect() and phy_disconnect() from probe and remove.
In such a case, the PHY will be powered down during the phy_stop()
call, but will fail to be powered up in phy_start().
This patch fixes this scenario.
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds UPDATE_QP SRIOV wrapper support.
The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've missed to add a NULL entry to the bond_intmax_tbl when I introduced
it with the conversion of arp_interval so add it now.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Fixes: 7bdb04ed0dbf ("bonding: convert arp_interval to use the new option API")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port->count was used to count the number of macvlan devs
in the same port, but the list vlans could play the same role
to do that, so free the port if the list vlans is empty and
no need to use the parameter count.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original series for reintroducing grant mapping for netback had a patch [1]
to handle receiving of packets from an another VIF. Grant copy on the receiving
side needs the grant ref of the page to set up the op.
The original patch assumed (wrongly) that the frags array haven't changed. In
the case reported by Sander, the sending guest sent a packet where the linear
buffer and the first frag were under PKT_PROT_LEN (=128) bytes.
xenvif_tx_submit() then pulled up the linear area to 128 bytes, and ditched the
first frag. The receiving side had an off-by-one problem when gathered the grant
refs.
This patch fixes that by checking whether the actual frag's page pointer is the
same as the page in the original frag list. It can handle any kind of changes on
the original frags array, like:
- removing granted frags from the array at any point
- adding local pages to the frags list anywhere
- reordering the frags
It's optimized to the most common case, when there is 1:1 relation between the
frags and the list, plus works optimal when frags are removed from the end or
the beginning.
[1]: 3e2234: xen-netback: Handle foreign mapped pages on the guest RX path
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the call to phy_init_hw failed in phy_attach_direct, phy_detach is called
to detach the phy device from its network device. If the attached driver is a
generic phy driver, this also detaches the driver. Subsequently phy_resume
is called, which assumes without checking that a driver is attached to the
device. This will result in a crash such as
Unable to handle kernel paging request for data at address 0xffffffffffffff90
Faulting instruction address: 0xc0000000003a0e18
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0000000003a0e18] .phy_attach_direct+0x68/0x17c
LR [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c
Call Trace:
[c0000003fc0475d0] [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c (unreliable)
[c0000003fc047670] [c0000000003a0ff8] .phy_connect_direct+0x28/0x98
[c0000003fc047700] [c0000000003f0074] .of_phy_connect+0x4c/0xa4
Only call phy_resume if phy_init_hw was successful.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdev_priv is an accessor function, and has no purpose if its result is
not used.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@ local idexpression x; @@
-x = netdev_priv(...);
... when != x
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdev_priv is an accessor function, and has no purpose if its result is
not used.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@ local idexpression x; @@
-x = netdev_priv(...);
... when != x
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets need to be at least 64 bytes to enter the switch port logic,
including the FCS, otherwise they will be discarded as RUNT packets.
With packets having Broadcom tags, the 4-bytes tag is first stripped
off the packet, and the packet length is then checked, so we need to
make sure that the packet length with FCS is at least 64 bytes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link adjustment callback can be called as frequently as desired by
the PHY library, as such, let's avoid doing a Read/Modify/Write sequence
if nothing changed, which is more than likely since we are interfaced
with a switch device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables multicast hash filtering if present in the hardware
and uses promiscuous mode instead until the problem with multicast
filtering has been debugged, integrated and tested.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the many sparse errors and warnings contained in the
initial submission of the Altera Triple Speed Ethernet driver, and a
few minor cppcheck warnings. Changes are tested on ARM and NIOS2
example designs, and compile tested against multiple architectures.
Typical issues addressed were as follows:
altera_tse_ethtool.c:136:19: warning: incorrect type in argument
1 (different address spaces)
altera_tse_ethtool.c:136:19: expected void const volatile
[noderef] <asn:2>*addr
altera_tse_ethtool.c:136:19: got unsigned int *<noident>
...
altera_sgdma.c:129:31: warning: cast removes address space of
expression
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These should not have trailing semicolons so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the behaviour with other network device drivers and
allows for a matching of the PCI device path in UDEV rules.
Signed-off-by: Markus Lottmann <markus.lottmann1986@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert kzalloc() to devm_kzalloc().
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the lone pr_err() to dev_err() call.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
