Removed the infinite loop in our arch_reset().
After calling arch_reset(), the kernel waits for 1 second before
printing a "reboot failed" message and then waits for ever itself.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The USB Device port registers are already defined in
drivers/usb/gadget/at91_udc.h. This file can therefore just be removed.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the 'is_b' variable with 'slot_b' in at91_mmc_data.
Also add the new 'chipselect' variable for CF/PCMCIA and 'bus_width_16'
variable for NAND.
This (and previous patches) will unfortunately break the current MMC,
USB Gadget and PCMCIA drivers. Updates and fixes for those drivers will
be submitted to the various subsystem maintainers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
XScale cores either have a DSP coprocessor (which contains a single
40 bit accumulator register), or an iWMMXt coprocessor (which contains
eight 64 bit registers.)
Because of the small amount of state in the DSP coprocessor, access to
the DSP coprocessor (CP0) is always enabled, and DSP context switching
is done unconditionally on every task switch. Access to the iWMMXt
coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is
first issued, and iWMMXt context switching is done lazily.
CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will
have iWMMXt support', but boards are supposed to select this config
symbol by hand, and at least one pxa27x board doesn't get this right,
so on that board, proc-xscale.S will incorrectly assume that we have a
DSP coprocessor, enable CP0 on boot, and we will then only save the
first iWMMXt register (wR0) on context switches, which is Bad.
This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on
might have iWMMXt support, and we will enable iWMMXt context switching
if it does.' This means that with this patch, running a CONFIG_IWMMXT=n
kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt
state over context switches, and running a CONFIG_IWMMXT=y kernel on a
non-iWMMXt capable CPU will still do DSP context save/restore.
These changes should make iWMMXt work on PXA3xx, and as a side effect,
enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such
as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined),
as well as setting and using HWCAP_IWMMXT properly.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* sanitize prototypes, annotate
* kill csum_partial_copy
* usual ntohs->shift, this time in assembler part
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge L_PTE_COHERENT with L_PTE_SHARED and free up a L_PTE_* bit.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add arch specific dev_archdata to struct device
Adds an arch specific struct dev_arch to struct device. This enables
architecture to add specific fields to every device in the system, like
DMA operation pointers, NUMA node ID, firmware specific data, etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andi Kleen <ak@suse.de>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Create include/asm-arm/arch-ixp4xx/udc.h and
add platfrom device ixp4xx_udc_device into
arch/arm/mach-ixp4xx/common.c.
This allows us to use pxa2xx-udc on
the ixp4xx platfrom. Both pxa2xx and
ixp4xx use the same device controller.
Signed-off-by:Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch includes a number of small changes for integrating the
AT91SAM9261 and AT91SAM0260 support.
* Can only select support for one AT91 processor at a time.
* Remove most of the remaining static memory mapping for the
AT91RM9200.
* Reserve 1Mb of memory below the IO for mapping the internal SRAM
and any custom board-specific devices (ie, FPGA).
* The SAM9260 has more serial ports, so increase the maximum to 7.
* Define the standard chipselect addresses, and define other
addresses relative to those.
* CLOCK_TICK_RATE is different on the SAM926x's.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the timer on the Atmel AT91SAM9261 and AT91SAM9260
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most architectures have fairly simple discontiguous memory - a
simple set of successive regions each containing some memory.
These can be described simply as a log2 of their maximum size,
along with the base address of the first region and the number
of regions.
The base address is already described by PHYS_PFN_OFFSET, and
the number of regions via the MAX_NUMNODES and the number of
online nodes.
If we then supply the log2 of their maximum size, all the other
discontigmem macros can move into generic code.
There is one exception: lh7a40x seems to have a more complicated
setup; this is left alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds definitions for the new peripherals integrated in the
AT91SAM9260 and AT91SAM9261 processors: ECC, LCD, RSTC, RTT, SHDWC,
WDT, MATRIX, SDRAMC, SMC.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the drivers (and other files) which include the
hardware headers. This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).
The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h. Renamed it to at91_pdc.h
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most of the AT91RM9200 user peripherals are also integrated into the
Atmel SAM9 range of processors. This patch renames the headers from
at91rm9200_xx.h to at91_xx.h to indicate they're not
at91rm9200-specific.
The new SAM9-specific registers and register bits have also been
defined.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91RM9200 system header file (at91rm9200_sys.h) has been split into
separate header files for each peripheral. This was necessary since
some of the system peripherals are also used on AT91SAM9260 and
AT91SAM9261.
The new SAM9-specific register bits have also been defined.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the initial support for the newer Atmel AT91SAM9261 and
AT91SAM9260 processors. The code is based on, and makes use of, the
existing AT91RM9200 support.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch replaces the arch_identify() in system.h with a set of
cpu_is_XXX() macro's. This allows for compile-time checking of the
target AT91 processor.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The external interrupt sources are different on the various AT91
processors. This patch introduces the global 'at91_extern_irq' variable
that contains a bitset of the available external interrupt sources.
The processor reset mechanism also differs on the various AT91
processors. This patch also adds a global 'at91_arch_reset' callback
(from system.h) into the processor-specific code to perform the reset.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove ARM local cache of 4 struct thread_info.
Can cause oops under certain circumstances.
Russell indicated the original optimization was
required on older kernels to avoid thread starvation
on memory fragmentation, but may no longer be
required. I've updated the patch to 19rc4 and
ensured no <config.h> dain-bramage slipped in this
time (sorry about that).
Original description follows:
I was given some test results which pointed to an
Oops in alloc_thread_info (happened 2x), and after
looking at the code, I see that ARM has its own
local cache of 4 struct thread_info. There wasn't
any clear (to me) synchronization between the
alloc_thread_info and the free_thread_info.
I looked over the other arch, and they all simply
allocate them on an as needed basis, so I simplified
the ARM to do the same, based on the other arch
(e.g. PPC) and the folks doing the testing have
indicated that this fixed the oops.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The "translated" io macros were never really used. Remove them.
Preserve the L7200 inb() and friends by defining the __io()
macro, so that the generic versions can be used instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the last definitions of this macros have been removed, we
can remove the warnings in asm/io.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These functions have been deprecated for quite some time, and in
fact are no longer used. They just add to clutter. Remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix warnings and errors in arch/arm/mm for nommu build.
Remove commented out function prototype in pgtable-nommu.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* We don't need this header anymore - there is no data we need to share this way. FB driver gets this data through a resources structure. MCU Driver api will go to a jornada720_mcu.h file.
Signed-off-by: Filip Zyzniewski <filip.zyzniewski@tefnet.pl>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates a bit definition name to align with the PXA27x
spec.EORINTR(End-Of-Receive Intr) bit in DCSR register (DMA Channel
Control/Status Register)
Signed-off-by: Stanley Cai <stanley.w.cai@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates several bit definitions name in UDCISR1 register.
Signed-off-by: Stanley Cai <stanley.w.cai@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move HWCAP_* definitions into asm/elf.h, where they should belong.
Since userspace wants to get at these definitions by including
asm/procinfo.h, include asm/elf.h from this file if __KERNEL__
is not defined, and issue a warning suggesting to fix the program
up to use asm/elf.h instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These files want to provide/access ELF hwcap information, so should
be including asm/elf.h rather than asm/procinfo.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move declaration of struct pxa2xx_udc_mach_info from
include/asm-arm/arch-pxa/udc.h to new file
include/asm-arm/mach/udc_pxa2xx.h.
This allow us to use this structure with
multiple platforms - pxa and ixp4xx. USB
device controller used in pxa25x is the same
as controller used in ixp4xx.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/*
* Note: Drivers should NOT use this function directly, as it will break
* platforms with CONFIG_DMABOUNCE.
* Use the driver DMA support - see dma-mapping.h (dma_sync_*)
*/
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove two warnings:
drivers/serial/8250_early.c:136: warning: unused variable 'mapsize'
include/linux/io.h:47: warning: passing argument 1 of '__readb' discards qualifiers from pointer target type
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixed definition of some CIF registers; see PXA27x Developer\'s Manual.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA255 has 84 GPIO lines available. This patch allows access to 81-84
Signed-off-by: Craig Hughes <craig@gumstix.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds relevant MCU commands for the j7xx chipset.
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a register bit definition for the pxa27x SSP port Frame
Sync Relative Timing (FSRT) bit.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's nothing arch-specific about check_signature(), so move it to
<linux/io.h>. Use a cross between the Alpha and i386 implementations as
the generic one.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename at91_register_uart_fns and associated structs and variables
to make it consistent with the atmel_ prefix used by the rest of
the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
