[ Upstream commit f0410bbf7d0fb80149e3b17d11d31f5b5197873e ]
DW APB SSI DMA-part of the driver may need to perform the requested
SPI-transfer synchronously. In that case the dma_transfer() callback
will return 0 as a marker of the SPI transfer being finished so the
SPI core doesn't need to wait and may proceed with the SPI message
trasnfers pumping procedure. This will be needed to fix the problem
when DMA transactions are finished, but there is still data left in
the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer
to return 1 as the normal dw_spi_transfer_one() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dadde344d965566589cd82797893d5aa06557a3 ]
By unknown reason the commit 64bee4d28c9e
("spi / ACPI: add ACPI enumeration support")
missed the DataBitLength property to encounter when parse SPI slave
device data from ACPI.
Fill the gap here.
Fixes: 64bee4d28c9e ("spi / ACPI: add ACPI enumeration support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200413180406.1826-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46164fde6b7890e7a3982d54549947c8394c0192 ]
Tx-only DMA transfers are working perfectly fine since in this case
the code just ignores the Rx FIFO overflow interrupts. But it turns
out the SPI Rx-only transfers are broken since nothing pushing any
data to the shift registers, so the Rx FIFO is left empty and the
SPI core subsystems just returns a timeout error. Since DW DMAC
driver doesn't support something like cyclic write operations of
a single byte to a device register, the only way to support the
Rx-only SPI transfers is to fake it by using a dummy Tx-buffer.
This is what we intend to fix in this commit by setting the
SPI_CONTROLLER_MUST_TX flag for DMA-capable platform.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43dba9f3f98c2b184a19f856f06fe22817bfd9e0 ]
It's pointless to track the Tx overrun interrupts if Rx-only SPI
transfer is issued. Similarly there is no need in handling the Rx
overrun/underrun interrupts if Tx-only SPI transfer is executed.
So lets unmask the interrupts only if corresponding SPI
transactions are implied.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cb97e223d277f84171cc4ccecab31e08b2ee7b5 ]
Some DMA controller drivers do not tolerate non-zero values in
the DMA configuration structures. Zero them to avoid issues with
such DMA controller drivers. Even despite above this is a good
practice per se.
Fixes: 7063c0d942a1 ("spi/dw_spi: add DMA support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eefaee4f2d366a389da0eb95e524ba82bf358c4 ]
With a couple allies at Intel, and much badgering, I got confirmation
from Intel that at least BXT suffers from the same SPI chip-select
issue as Cannonlake (and beyond). The issue being that after going
through runtime suspend/resume, toggling the chip-select line without
also sending data does nothing.
Add the quirk to BXT to briefly toggle dynamic clock gating off and
on, forcing the fabric to wake up enough to notice the CS register
change.
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: Shobhit Srivastava <shobhit.srivastava@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200427163238.1.Ib1faaabe236e37ea73be9b8dcc6aa034cb3c8804@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80300a7d5f2d7178335652f41d2e55ba898b4ec1 ]
Currently buswidths 2 and 4 are rejected for a device that advertises
Octal capabilities. Allow these buswidths, just like is done for
buswidth 2 and Quad-capable devices.
Fixes: b12a084c8729ef42 ("spi: spi-mem: add support for octal mode I/O data transfer")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200416101418.14379-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4df3bea7f9d2ddd9ac2c29ba945c7c4db2def29c upstream.
Currently we set the tx/rx buffer to 0xff when NULL. This causes
problems with some spi slaves where 0xff is a valid command. Looking
at other drivers, the tx/rx buffer is usually set to 0x00 when NULL.
Following this convention solves the issue.
Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200420190853.45614-6-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0392727c261bab65a35cd4f82ee9459bc237591d upstream.
The clock provider may not be ready by the time spi-bcm-qspi gets
probed, handle probe deferral using devm_clk_get_optional().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200420190853.45614-2-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9dd3f6d417258ad0beeb292a1bc74200149f15d upstream.
The BCM2835aux SPI driver uses devm_spi_register_master() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835aux_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835aux_spi_remove() turns off the SPI
controller, including its interrupts and clock. The SPI controller
is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_master() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_master(). Note that the
struct spi_master as well as the driver-private data are not freed until
after bcm2835aux_spi_remove() has finished, so accessing them is safe.
Fixes: 1ea29b39f4c8 ("spi: bcm2835aux: add bcm2835 auxiliary spi device driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.4+
Cc: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/32f27f4d8242e4d75f9a53f7e8f1f77483b08669.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dd277ff92d06f6aa95b39936ad83981d781f49b upstream.
The BCM2835 SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835_spi_remove() tears down the DMA
channels and turns off the SPI controller, including its interrupts
and clock. The SPI controller is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_controller(). Note that
the struct spi_controller as well as the driver-private data are not
freed until after bcm2835_spi_remove() has finished, so accessing them
is safe.
Fixes: 247263dba208 ("spi: bcm2835: use devm_spi_register_master()")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Link: https://lore.kernel.org/r/2397dd70cdbe95e0bc4da2b9fca0f31cb94e5aed.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65e318e17358a3fd4fcb5a69d89b14016dee2f06 upstream.
The PXA2xx SPI driver releases a runtime PM ref in the probe error path
even though it hasn't acquired a ref earlier.
Apparently commit e2b714afee32 ("spi: pxa2xx: Disable runtime PM if
controller registration fails") sought to copy-paste the invocation of
pm_runtime_disable() from pxa2xx_spi_remove(), but erroneously copied
the call to pm_runtime_put_noidle() as well. Drop it.
Fixes: e2b714afee32 ("spi: pxa2xx: Disable runtime PM if controller registration fails")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v4.17+
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/58b2ac6942ca1f91aaeeafe512144bc5343e1d84.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32e5b57232c0411e7dea96625c415510430ac079 upstream.
The PXA2xx SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
pxa2xx_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: pxa2xx_spi_remove() disables the chip,
rendering the SPI bus inaccessible even though the SPI controller is
still registered. When the SPI controller is subsequently unregistered,
it unbinds all its slave devices. Because their drivers cannot access
the SPI bus, e.g. to quiesce interrupts, the slave devices may be left
in an improper state.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed after
unregistering the controller and specifically after unbinding of slaves.
Fix by reverting to the non-devm variant of spi_register_controller().
An alternative approach would be to use device-managed functions for all
steps in pxa2xx_spi_remove(), e.g. by calling devm_add_action_or_reset()
on probe. However that approach would add more LoC to the driver and
it wouldn't lend itself as well to backporting to stable.
The improper use of devm_spi_register_controller() was introduced in 2013
by commit a807fcd090d6 ("spi: pxa2xx: use devm_spi_register_master()"),
but all earlier versions of the driver going back to 2006 were likewise
broken because they invoked spi_unregister_master() at the end of
pxa2xx_spi_remove(), rather than at the beginning.
Fixes: e0c9905e87ac ("[PATCH] SPI: add PXA2xx SSP SPI Driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v2.6.17+
Cc: Tsuchiya Yuto <kitakar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206403#c1
Link: https://lore.kernel.org/r/834c446b1cf3284d2660f1bee1ebe3e737cd02a9.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84855678add8aba927faf76bc2f130a40f94b6f7 upstream.
When an SPI controller unregisters, it unbinds all its slave devices.
For this, their drivers may need to access the SPI bus, e.g. to quiesce
interrupts.
However since commit ffbbdd21329f ("spi: create a message queueing
infrastructure"), spi_destroy_queue() is executed before unbinding the
slaves. It sets ctlr->running = false, thereby preventing SPI bus
access and causing unbinding of slave devices to fail.
Fix by unbinding slaves before calling spi_destroy_queue().
Fixes: ffbbdd21329f ("spi: create a message queueing infrastructure")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.4+
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/8aaf9d44c153fe233b17bc2dec4eb679898d7e7b.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca8b19d61e3fce5d2d7790cde27a0b57bcb3f341 upstream.
The Designware SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
dw_spi_remove_host() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: dw_spi_remove_host() shuts down the chip,
rendering the SPI bus inaccessible even though the SPI controller is
still registered. When the SPI controller is subsequently unregistered,
it unbinds all its slave devices. Because their drivers cannot access
the SPI bus, e.g. to quiesce interrupts, the slave devices may be left
in an improper state.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed after
unregistering the controller and specifically after unbinding of slaves.
Fix by reverting to the non-devm variant of spi_register_controller().
An alternative approach would be to use device-managed functions for all
steps in dw_spi_remove_host(), e.g. by calling devm_add_action_or_reset()
on probe. However that approach would add more LoC to the driver and
it wouldn't lend itself as well to backporting to stable.
Fixes: 04f421e7b0b1 ("spi: dw: use managed resources")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v3.14+
Cc: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/3fff8cb8ae44a9893840d0688be15bb88c090a14.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9aea644ca17b94f82ad7fa767cbc4509642f4420 ]
Commit 6e0a32d6f376 ("spi: dw: Fix default polarity of native
chipselect") attempted to fix the problem when GPIO active-high
chip-select is utilized to communicate with some SPI slave. It fixed
the problem, but broke the normal native CS support. At the same time
the reversion commit ada9e3fcc175 ("spi: dw: Correct handling of native
chipselect") didn't solve the problem either, since it just inverted
the set_cs() polarity perception without taking into account that
CS-high might be applicable. Here is what is done to finally fix the
problem.
DW SPI controller demands any native CS being set in order to proceed
with data transfer. So in order to activate the SPI communications we
must set any bit in the Slave Select DW SPI controller register no
matter whether the platform requests the GPIO- or native CS. Preferably
it should be the bit corresponding to the SPI slave CS number. But
currently the dw_spi_set_cs() method activates the chip-select
only if the second argument is false. Since the second argument of the
set_cs callback is expected to be a boolean with "is-high" semantics
(actual chip-select pin state value), the bit in the DW SPI Slave
Select register will be set only if SPI core requests the driver
to set the CS in the low state. So this will work for active-low
GPIO-based CS case, and won't work for active-high CS setting
the bit when SPI core actually needs to deactivate the CS.
This commit fixes the problem for all described cases. So no matter
whether an SPI slave needs GPIO- or native-based CS with active-high
or low signal the corresponding bit will be set in SER.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Fixes: ada9e3fcc175 ("spi: dw: Correct handling of native chipselect")
Fixes: 6e0a32d6f376 ("spi: dw: Fix default polarity of native chipselect")
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200515104758.6934-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfda044533b213985bc62bd7ca96f2b984d21b80 ]
Because of out-of-order execution about some CPU architecture,
In this debug stage we find Completing spi interrupt enable ->
prodrucing TXEI interrupt -> running "interrupt_transfer" function
will prior to set "dw->rx and dws->rx_end" data, so this patch add
memory barrier to enable dw->rx and dw->rx_end to be visible and
solve to send SPI data error.
eg:
it will fix to this following low possibility error in testing environment
which using SPI control to connect TPM Modules
kernel: tpm tpm0: Operation Timed out
kernel: tpm tpm0: tpm_relinquish_locality: : error -1
Signed-off-by: fengsheng <fengsheng5@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Link: https://lore.kernel.org/r/1578019930-55858-1-git-send-email-kong.kongxinwei@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f5ee75ea1718a09149460b3df993f389a67b56a ]
Currently the driver puts the process in interruptible sleep waiting for
the interrupt train to finish transfer to/from the tx_buf and rx_buf.
But exiting the process with ctrl-c may make the kernel panic: the
wait_event_interruptible call will return -ERESTARTSYS, which a proper
driver implementation is perhaps supposed to handle, but nonetheless
this one doesn't, and aborts the transfer altogether.
Actually when the task is interrupted, there is still a high chance that
the dspi_interrupt is still triggering. And if dspi_transfer_one_message
returns execution all the way to the spi_device driver, that can free
the spi_message and spi_transfer structures, leaving the interrupts to
access a freed tx_buf and rx_buf.
hexdump -C /dev/mtd0
00000000 00 75 68 75 0a ff ff ff ff ff ff ff ff ff ff ff
|.uhu............|
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
|................|
*
^C[ 38.495955] fsl-dspi 2120000.spi: Waiting for transfer to complete failed!
[ 38.503097] spi_master spi2: failed to transfer one message from queue
[ 38.509729] Unable to handle kernel paging request at virtual address ffff800095ab3377
[ 38.517676] Mem abort info:
[ 38.520474] ESR = 0x96000045
[ 38.523533] EC = 0x25: DABT (current EL), IL = 32 bits
[ 38.528861] SET = 0, FnV = 0
[ 38.531921] EA = 0, S1PTW = 0
[ 38.535067] Data abort info:
[ 38.537952] ISV = 0, ISS = 0x00000045
[ 38.541797] CM = 0, WnR = 1
[ 38.544771] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000082621000
[ 38.551494] [ffff800095ab3377] pgd=00000020fffff003, p4d=00000020fffff003, pud=0000000000000000
[ 38.560229] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[ 38.565819] Modules linked in:
[ 38.568882] CPU: 0 PID: 2729 Comm: hexdump Not tainted 5.6.0-rc4-next-20200306-00052-gd8730cdc8a0b-dirty #193
[ 38.578834] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT)
[ 38.587129] pstate: 20000085 (nzCv daIf -PAN -UAO)
[ 38.591941] pc : ktime_get_real_ts64+0x3c/0x110
[ 38.596487] lr : spi_take_timestamp_pre+0x40/0x90
[ 38.601203] sp : ffff800010003d90
[ 38.604525] x29: ffff800010003d90 x28: ffff80001200e000
[ 38.609854] x27: ffff800011da9000 x26: ffff002079c40400
[ 38.615184] x25: ffff8000117fe018 x24: ffff800011daa1a0
[ 38.620513] x23: ffff800015ab3860 x22: ffff800095ab3377
[ 38.625841] x21: 000000000000146e x20: ffff8000120c3000
[ 38.631170] x19: ffff0020795f6e80 x18: ffff800011da9948
[ 38.636498] x17: 0000000000000000 x16: 0000000000000000
[ 38.641826] x15: ffff800095ab3377 x14: 0720072007200720
[ 38.647155] x13: 0720072007200765 x12: 0775076507750771
[ 38.652483] x11: 0720076d076f0772 x10: 0000000000000040
[ 38.657812] x9 : ffff8000108e2100 x8 : ffff800011dcabe8
[ 38.663139] x7 : 0000000000000000 x6 : ffff800015ab3a60
[ 38.668468] x5 : 0000000007200720 x4 : ffff800095ab3377
[ 38.673796] x3 : 0000000000000000 x2 : 0000000000000ab0
[ 38.679125] x1 : ffff800011daa000 x0 : 0000000000000026
[ 38.684454] Call trace:
[ 38.686905] ktime_get_real_ts64+0x3c/0x110
[ 38.691100] spi_take_timestamp_pre+0x40/0x90
[ 38.695470] dspi_fifo_write+0x58/0x2c0
[ 38.699315] dspi_interrupt+0xbc/0xd0
[ 38.702987] __handle_irq_event_percpu+0x78/0x2c0
[ 38.707706] handle_irq_event_percpu+0x3c/0x90
[ 38.712161] handle_irq_event+0x4c/0xd0
[ 38.716008] handle_fasteoi_irq+0xbc/0x170
[ 38.720115] generic_handle_irq+0x2c/0x40
[ 38.724135] __handle_domain_irq+0x68/0xc0
[ 38.728243] gic_handle_irq+0xc8/0x160
[ 38.732000] el1_irq+0xb8/0x180
[ 38.735149] spi_nor_spimem_read_data+0xe0/0x140
[ 38.739779] spi_nor_read+0xc4/0x120
[ 38.743364] mtd_read_oob+0xa8/0xc0
[ 38.746860] mtd_read+0x4c/0x80
[ 38.750007] mtdchar_read+0x108/0x2a0
[ 38.753679] __vfs_read+0x20/0x50
[ 38.757002] vfs_read+0xa4/0x190
[ 38.760237] ksys_read+0x6c/0xf0
[ 38.763471] __arm64_sys_read+0x20/0x30
[ 38.767319] el0_svc_common.constprop.3+0x90/0x160
[ 38.772125] do_el0_svc+0x28/0x90
[ 38.775449] el0_sync_handler+0x118/0x190
[ 38.779468] el0_sync+0x140/0x180
[ 38.782793] Code: 91000294 1400000f d50339bf f9405e80 (f90002c0)
[ 38.788910] ---[ end trace 55da560db4d6bef7 ]---
[ 38.793540] Kernel panic - not syncing: Fatal exception in interrupt
[ 38.799914] SMP: stopping secondary CPUs
[ 38.803849] Kernel Offset: disabled
[ 38.807344] CPU features: 0x10002,20006008
[ 38.811451] Memory Limit: none
[ 38.814513] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
So it is clear that the "interruptible" part isn't handled correctly.
When the process receives a signal, one could either attempt a clean
abort (which appears to be difficult with this hardware) or just keep
restarting the sleep until the wait queue really completes. But checking
in a loop for -ERESTARTSYS is a bit too complicated for this driver, so
just make the sleep uninterruptible, to avoid all that nonsense.
The wait queue was actually restructured as a completion, after polling
other drivers for the most "popular" approach.
Fixes: 349ad66c0ab0 ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-7-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9981d4f50b475d7dbb70f3022b87a3c8bba9fd6 ]
Some error paths leave the bus id allocated. As a result the IDR
allocation will fail after a deferred probe. Fix by freeing the bus id
always on error.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Message-Id: <20200304111740.27915-1-aaro.koskinen@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd8304981ecffa77bb72b1c57c4be5dfe6cfae9 ]
In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.
This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.
The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.
It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 683f65ded66a9a7ff01ed7280804d2132ebfdf7e ]
In some circumstances on Intel LPSS controllers, toggling the LPSS
CS control register doesn't actually cause the CS line to toggle.
This seems to be failure of dynamic clock gating that occurs after
going through a suspend/resume transition, where the controller
is sent through a reset transition. This ruins SPI transactions
that either rely on delay_usecs, or toggle the CS line without
sending data.
Whenever CS is toggled, momentarily set the clock gating register
to "Force On" to poke the controller into acting on CS.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200211223700.110252-1-rajatja@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 136b5cd2e2f97581ae560cff0db2a3b5369112da ]
spi_qup_suspend() will cause synchronous external abort when
runtime suspend is enabled and applied, as it tries to
access SPI controller register while clock is already disabled
in spi_qup_pm_suspend_runtime().
Signed-off-by: Yuji sasaki <sasakiy@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200214074340.2286170-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32f2fc5dc3992b4b60cc6b1a6a31be605cc9c3a2 ]
dma_request_channel() can return -EPROBE_DEFER, if DMA driver is not
ready. Currently driver just falls back to PIO mode on probe deferral.
Fix this by requesting all required channels during probe and
propagating EPROBE_DEFER error code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e093ea4d3593379be46b845b9e823179558047e upstream.
The QSPI controller memory space is limited to 128MB:
0x9000_00000-0x9800_00000/0XD000_0000--0XD800_0000.
There are nor flashes that are bigger in size than the memory size
supported by the controller: Micron MT25QL02G (256 MB).
Check if the address exceeds the MMIO window size. An improvement
would be to add support for regular SPI mode and fall back to it
when the flash memories overrun the controller's memory space.
Fixes: 0e6aae08e9ae ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200228155437.1558219-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51bddd4501bc414b8b1e8f4d096b4a5304068169 upstream.
The purpose of commit 0fd85869c2a9 ("spi/bcm63xx-hsspi: keep pll clk enabled")
was to keep the pll clk enabled through the lifetime of the device.
In order to do that, some 'clk_prepare_enable()'/'clk_disable_unprepare()'
calls have been added in the error handling path of the probe function, in
the remove function and in the suspend and resume functions.
However, a 'clk_disable_unprepare()' call has been unfortunately left in
the probe function. So the commit seems to be more or less a no-op.
Axe it now, so that the pll clk is left enabled through the lifetime of
the device, as described in the commit.
Fixes: 0fd85869c2a9 ("spi/bcm63xx-hsspi: keep pll clk enabled")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20200228213838.7124-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 138c9c32f090894614899eca15e0bb7279f59865 upstream.
Commit f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change broke userspace applications which issue an SPI_IOC_WR_MODE
ioctl() to an spidev: Chip Select polarity will be incorrect unless the
application is changed to set SPI_CS_HIGH. And once changed, it will be
incompatible with kernels not containing the commit.
Fix by setting SPI_CS_HIGH in spidev_ioctl() (under the same conditions
as in of_spi_parse_dt()).
Fixes: f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/fca3ba7cdc930cd36854666ceac4fbcf01b89028.1582027457.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0177aca7aea7e8917d4e463334b51facb293d02 ]
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 84d043185dbe ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc3a8b295e5bca9d1ec2622a6ba38289f9fd3d8a ]
Why it does not work at the moment:
- num_chipselect sets the number of cs-gpios that are in the DT.
This comes from drivers/spi/spi.c
- num_chipselect gets set with devm_spi_register_controller, that is
called in drivers/spi/spi.c
- devm_spi_register_controller got called after num_chipselect has
been used.
How this commit fixes the issue:
- devm_spi_register_controller gets called before num_chipselect is
being used.
Fixes: c7a402599504 ("spi: lpspi: use the core way to implement cs-gpio function")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20191204141312.1411251-1-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 057b8945f78f76d0b04eeb5c27cd9225e5e7ad86 upstream.
In fsl_lpspi_probe an SPI controller is allocated either via
spi_alloc_slave or spi_alloc_master. In all but one error cases this
controller is put by going to error handling code. This commit fixes the
case when pm_runtime_get_sync fails and it should go to the error
handling path.
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20190930034602.1467-1-navid.emamdoost@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2de860b4a7a0bd5a4b5bd3bff0e6a615495df4ba upstream.
As platform_get_irq_byname() now prints an error when the interrupt
does not exist, scary warnings may be printed for optional interrupts:
renesas_spi e6b10000.spi: IRQ rx not found
renesas_spi e6b10000.spi: IRQ mux not found
Fix this by calling platform_get_irq_byname_optional() instead.
Remove the no longer needed printing of platform_get_irq errors, as the
remaining calls to platform_get_irq() and platform_get_irq_byname() take
care of that.
Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191016143101.28738-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fed8d8c7a6dc2a76d7764842853d81c770b0788e upstream.
The driver does the wrong thing when cs_change is set on a non-last
xfer in a message. When cs_change is set, the driver deactivates the
CS and leaves it off until a later xfer again has cs_change set whereas
it should be briefly toggling CS off and on again.
This patch brings the behaviour of the driver back in line with the
documentation and common sense. The delay of 10 us is the same as is
used by the default spi_transfer_one_message() function in spi.c.
[gregory: rebased on for-5.5 from spi tree]
Fixes: 8090d6d1a415 ("spi: atmel: Refactor spi-atmel to use SPI framework queue")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018153504.4249-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2662a164f9dc48da8822e56600686d639056282 upstream.
In DMA mode we have a maximum transfer size, past that the driver
falls back to PIO (see the check at the top of pxa2xx_spi_transfer_one).
Falling back to PIO for big transfers defeats the point of a dma engine,
hence set the max transfer size to inform spi clients that they need
to do something smarter.
This was uncovered by the drm_mipi_dbi spi panel code, which does
large spi transfers, but stopped splitting them after:
commit e143364b4c1774f68e923a5a0bb0fca28ac25888
Author: Noralf Trønnes <noralf@tronnes.org>
Date: Fri Jul 19 17:59:10 2019 +0200
drm/tinydrm: Remove tinydrm_spi_max_transfer_size()
After this commit the code relied on the spi core to split transfers
into max dma-able blocks, which also papered over the PIO fallback issue.
Fix this by setting the overall max transfer size to the DMA limit,
but only when the controller runs in DMA mode.
Fixes: e143364b4c17 ("drm/tinydrm: Remove tinydrm_spi_max_transfer_size()")
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Reported-and-tested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20191017064426.30814-1-daniel.vetter@ffwll.ch
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e9c5236b7b86779b53b762f7e66240c3f18314b upstream.
The original code used an incorrect SPI register to initialize the SPI
controller in sprd_spi_init_hw(), thus fix it.
Fixes: e7d973a31c24 ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Huanpeng Xin <huanpeng.xin@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/b4f7f89ec0fdc595335687bfbd9f962213bc4a1d.1575443510.git.baolin.wang7@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 007773e16a6f3f49d1439554078c3ba8af131998 ]
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a90 ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c52c91bb9aa6bd8c38dbf9776158e33038aedd43 ]
When switching ChipSelect from default CS0 to any other CS, driver fails
to update the bits in system control module register that control which
CS is mapped for MMIO access. This causes reads to fail when driver
tries to access QSPI flash on CS1/2/3.
Fix this by updating appropriate bits whenever active CS changes.
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191211155216.30212-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a841e2853e1afecc2ee692b8cc5bff606bc84e4c ]
The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075500.18525-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7251953d784baf7e5416afabe030a0e81de1a938 ]
The Freescale MPC8xxx had a special quirk for handling a
single hardwired chipselect, the case when we're using neither
GPIO nor native chip select: when inspecting the device tree
and finding zero "cs-gpios" on the device node the code would
assume we have a single hardwired chipselect that leaves the
device always selected.
This quirk is not handled by the new core code, so we need
to check the "cs-gpios" explicitly in the driver and set
pdata->max_chipselect = 1 which will later fall through to
the SPI master ->num_chipselect.
Make sure not to assign the chip select handler in this
case: there is no handling needed since the chip is always
selected, and this is what the old code did as well.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> (No tested the
Link: https://lore.kernel.org/r/20191128083718.39177-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f106904968e2a075e64653b9b79dda9f0f070ab5 ]
This makes the driver actually support looking up GPIO
descriptor. A coding mistake in the initial descriptor
support patch was that it was failing to turn on the very
feature it was implementing. Mea culpa.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c7315c9fca5de203538163cf42699bb10328902 ]
LPSS SPI on Intel Jasper Lake is compatible with Intel Ice Lake which
follows Intel Cannon Lake. Add PCI IDs of Jasper Lake.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191125125159.15404-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9cd34efbd3012171c102910ce17ee632a3cccb44 upstream.
Rx threshold means the value to inform the receiver when the number of words
in Rx FIFO is equal to or more than the value. Similarly, Tx threshold means
the value to inform the sender when the number of words in Tx FIFO is equal
to or less than the value. The controller triggers the driver to start
the transfer.
In case of Rx, the driver wants to detect that the specified number of words
N are in Rx FIFO, so the value of Rx threshold should be N. In case of Tx,
the driver wants to detect that the same number of spaces as Rx are in
Tx FIFO, so the value of Tx threshold should be (FIFO size - N).
For example, in order for the driver to receive at least 3 words from
Rx FIFO, set 3 to Rx threshold.
+-+-+-+-+-+-+-+-+
| | | | | |*|*|*|
+-+-+-+-+-+-+-+-+
In order for the driver to send at least 3 words to Tx FIFO, because
it needs at least 3 spaces, set 8(FIFO size) - 3 = 5 to Tx threshold.
+-+-+-+-+-+-+-+-+
|*|*|*|*|*| | | |
+-+-+-+-+-+-+-+-+
This adds new function uniphier_spi_set_fifo_threshold() to set
threshold value to the register.
And more, FIFO counts by 'words', so this renames 'fill_bytes' with
'fill_words', and fixes the calculation using bytes_per_words.
Fixes: 37ffab817098 ("spi: uniphier: introduce polling mode")
Cc: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca59d5a51690d5b9340343dc36792a252e9414ae upstream.
When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.
In fact, the LS1021A reference manual says:
33.5.2.4.2 Draining the TX FIFO
When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.
So given the following TX buffer:
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 32-bit word 1 | 32-bit word 2 | 32-bit word 3 |
+-----------------------+-----------------------+-----------------------+
The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:
0x03020100
0x07060504
0x0b0a0908
But it is actually transmitted as following, as seen with a scope:
0x01000302
0x05040706
0x09080b0a
It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.
Fixes: 8fcd151d2619 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63aa6a692595d47a0785297b481072086b9272d2 upstream.
Unlike irq_of_parse_and_map() which has a dummy definition on SPARC,
of_irq_to_resource() hasn't.
But as platform_get_irq() can be used instead and is generic, use it.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Fixes: 3194d2533eff ("spi: fsl: don't map irq during probe")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/091a277fd0b3356dca1e29858c1c96983fc9cb25.1576172743.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61acd19f9c56fa0809285346bd0bd4a926ab0da0 ]
To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407ff0 ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada9e3fcc175db4538f5b5e05abf5dedf626e550 ]
This patch reverts commit 6e0a32d6f376 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd87669 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd050abeba2a95fe5374eec28ad2244617bcbab6 ]
The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118024848.21645-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04358e40ba96d687c0811c21d9dede73f5244a98 ]
The driver misses calling clk_unprepare in probe failure and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191115083122.12278-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eb263ef08b5014cfc2539a838f39d2fd3531423 ]
pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.
Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
