commit 314538041b5632ffaf64798faaeabaf2793fe029 upstream.
In AP mode WPA2-PSK connections were not established.
The reason was that the AP was sending the first message
of the 4 way handshake encrypted, even though no pairwise
key had (correctly) yet been set.
Encryption was enabled if the "security_enable" driver flag
was set and encryption was not explicitly disabled by
IEEE80211_TX_INTFL_DONT_ENCRYPT.
However security_enable was set when *any* key, including
the AP GTK key, had been set which was causing unwanted
encryption even if no key was avaialble for the unicast
packet to be sent.
Fix this by adding a check that we have a key and drop
the old security_enable driver flag which is insufficient
and redundant.
The Redpine downstream out of tree driver does it this way too.
Regarding the Fixes tag the actual code being modified was
introduced earlier, with the original driver submission, in
dad0d04fa7ba ("rsi: Add RS9113 wireless driver"), however
at that time AP mode was not yet supported so there was
no bug at that point.
So I have tagged the introduction of AP support instead
which was part of the patch set "rsi: support for AP mode" [1]
It is not clear whether AP WPA has ever worked, I can see nothing
on the kernel side that broke it afterwards yet the AP support
patch series says "Tests are performed to confirm aggregation,
connections in WEP and WPA/WPA2 security."
One possibility is that the initial tests were done with a modified
userspace (hostapd).
[1] https://www.spinics.net/lists/linux-wireless/msg165302.html
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Fixes: 38ef62353acb ("rsi: security enhancements for AP mode")
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1622564459-24430-1-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1c3a24897bd528f2f4fda9fea7da08a84ae25b6 upstream.
The RSI_RATE_x bits must be assigned to struct rsi_data_desc rate_info
field. The rest of the driver does it correctly, except this one place,
so fix it. This is also aligned with the RSI downstream vendor driver.
Without this patch, an AP operating at 5 GHz does not transmit any
beacons at all, this patch fixes that.
Fixes: d26a9559403c ("rsi: add beacon changes for AP mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210507213105.140138-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb312ac5ccb007e843f982b38d4d6886ba4b32f2 upstream.
I got this crash more times during debugging of PCIe controller and crash
happens somehow at the time when PCIe kernel code started link retraining (as
part of ASPM code) when at the same time PCIe link went down and ath9k probably
executed hw reset procedure.
Currently I'm not able to reproduce this issue as it looks like to be
some race condition between link training, ASPM, link down and reset
path. And as always, race conditions which depends on more input
parameters are hard to reproduce as it depends on precise timings.
But it is clear that pointers are zero in this case and should be
properly filled as same code pattern is used in ath9k_stop() function.
Anyway I was able to reproduce this crash by manually triggering ath
reset worker prior putting card up. I created simple patch to export
reset functionality via debugfs and use it to "simulate" of triggering
reset. s proved that NULL-pointer dereference issue is there.
Function ath9k_hw_reset() is dereferencing chan structure pointer, so it
needs to be non-NULL pointer.
Function ath9k_stop() already contains code which sets ah->curchan to valid
non-NULL pointer prior calling ath9k_hw_reset() function.
Add same code pattern also into ath_reset_internal() function to prevent
kernel NULL pointer dereference in ath9k_hw_reset() function.
This change fixes kernel NULL pointer dereference in ath9k_hw_reset() which
is caused by calling ath9k_hw_reset() from ath_reset_internal() with NULL
chan structure.
[ 45.334305] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
[ 45.344417] Mem abort info:
[ 45.347301] ESR = 0x96000005
[ 45.350448] EC = 0x25: DABT (current EL), IL = 32 bits
[ 45.356166] SET = 0, FnV = 0
[ 45.359350] EA = 0, S1PTW = 0
[ 45.362596] Data abort info:
[ 45.365756] ISV = 0, ISS = 0x00000005
[ 45.369735] CM = 0, WnR = 0
[ 45.372814] user pgtable: 4k pages, 39-bit VAs, pgdp=000000000685d000
[ 45.379663] [0000000000000008] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
[ 45.388856] Internal error: Oops: 96000005 [#1] SMP
[ 45.393897] Modules linked in: ath9k ath9k_common ath9k_hw
[ 45.399574] CPU: 1 PID: 309 Comm: kworker/u4:2 Not tainted 5.12.0-rc2-dirty #785
[ 45.414746] Workqueue: phy0 ath_reset_work [ath9k]
[ 45.419713] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--)
[ 45.425910] pc : ath9k_hw_reset+0xc4/0x1c48 [ath9k_hw]
[ 45.431234] lr : ath9k_hw_reset+0xc0/0x1c48 [ath9k_hw]
[ 45.436548] sp : ffffffc0118dbca0
[ 45.439961] x29: ffffffc0118dbca0 x28: 0000000000000000
[ 45.445442] x27: ffffff800dee4080 x26: 0000000000000000
[ 45.450923] x25: ffffff800df9b9d8 x24: 0000000000000000
[ 45.456404] x23: ffffffc0115f6000 x22: ffffffc008d0d408
[ 45.461885] x21: ffffff800dee5080 x20: ffffff800df9b9d8
[ 45.467366] x19: 0000000000000000 x18: 0000000000000000
[ 45.472846] x17: 0000000000000000 x16: 0000000000000000
[ 45.478326] x15: 0000000000000010 x14: ffffffffffffffff
[ 45.483807] x13: ffffffc0918db94f x12: ffffffc011498720
[ 45.489289] x11: 0000000000000003 x10: ffffffc0114806e0
[ 45.494770] x9 : ffffffc01014b2ec x8 : 0000000000017fe8
[ 45.500251] x7 : c0000000ffffefff x6 : 0000000000000001
[ 45.505733] x5 : 0000000000000000 x4 : 0000000000000000
[ 45.511213] x3 : 0000000000000000 x2 : ffffff801fece870
[ 45.516693] x1 : ffffffc00eded000 x0 : 000000000000003f
[ 45.522174] Call trace:
[ 45.524695] ath9k_hw_reset+0xc4/0x1c48 [ath9k_hw]
[ 45.529653] ath_reset_internal+0x1a8/0x2b8 [ath9k]
[ 45.534696] ath_reset_work+0x2c/0x40 [ath9k]
[ 45.539198] process_one_work+0x210/0x480
[ 45.543339] worker_thread+0x5c/0x510
[ 45.547115] kthread+0x12c/0x130
[ 45.550445] ret_from_fork+0x10/0x1c
[ 45.554138] Code: 910922c2 9117e021 95ff0398 b4000294 (b9400a61)
[ 45.560430] ---[ end trace 566410ba90b50e8b ]---
[ 45.565193] Kernel panic - not syncing: Oops: Fatal exception in interrupt
[ 45.572282] SMP: stopping secondary CPUs
[ 45.576331] Kernel Offset: disabled
[ 45.579924] CPU features: 0x00040002,0000200c
[ 45.584416] Memory Limit: none
[ 45.587564] Rebooting in 3 seconds..
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402122653.24014-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e41eb3e408de27982a5f8f50b2dd8002bed96908 upstream.
Sending nulldata packets is important for sw AP link probing and detecting
4-address mode links. The checks that dropped these packets were apparently
added to work around an iwlwifi firmware bug with multi-TID aggregation.
Fixes: 41cbb0f5a295 ("mac80211: add support for HE")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210619101517.90806-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b17233d385d0b6b43ecf81d43008cb1bbb008166 upstream.
Rather than just indicating that transmission can start, this patch
requires the explicit flushing of the network TX queue when the driver
is informed by the device that it can transmit, next to its
configuration.
In this way, if frames have already been written by the application,
they will actually be transmitted.
Fixes: ffd137f7043c ("can: peak/pcie_fd: remove useless code when interface starts")
Link: https://lore.kernel.org/r/20210623142600.149904-1-s.grosjean@peak-system.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6396341194234e9b01cd7538bc2c6ac4501ab14 ]
As documented in Documentation/networking/driver.rst, the ndo_start_xmit
method must not return NETDEV_TX_BUSY under any normal circumstances, and
as recommended, we simply stop the tx queue in advance, when there is a
risk that the next xmit would cause a NETDEV_TX_BUSY return.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28d9fab458b16bcd83f9dd07ede3d585c3e1a69e ]
Add a couple of memory-barriers to ensure correct ordering of read/write
access to TX BDs.
In xmit_done, we should ensure that reading the additional BD fields are
only done after STS_CTRL_APP0_CMPLT bit is set.
When xmit_done marks the BD as free by setting APP0=0, we need to ensure
that the other BD fields are reset first, so we avoid racing with the xmit
path, which writes to the same fields.
Finally, making sure to read APP0 of next BD after the current BD, ensures
that we see all available buffers.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c200f832e14420fa770193f9871f4ce2df00d07 ]
The source (&dcbx_info->operational.params) and dest
(&p_hwfn->p_dcbx_info->set.config.params) are both struct qed_dcbx_params
(560 bytes), not struct qed_dcbx_admin_params (564 bytes), which is used
as the memcpy() size.
However it seems that struct qed_dcbx_operational_params
(dcbx_info->operational)'s layout matches struct qed_dcbx_admin_params
(p_hwfn->p_dcbx_info->set.config)'s 4 byte difference (3 padding, 1 byte
for "valid").
On the assumption that the size is wrong (rather than the source structure
type), adjust the memcpy() size argument to be 4 bytes smaller and add
a BUILD_BUG_ON() to validate any changes to the structure sizes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da5ac772cfe2a03058b0accfac03fad60c46c24d ]
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 224004fbb033600715dbd626bceec10bfd9c58bc ]
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99718abdc00e86e4f286dd836408e2834886c16e ]
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58af3d3d54e87bfc1f936e16c04ade3369d34011 ]
Syzbot reported memory leak in tty_init_dev().
The problem was in unputted tty in ldisc_open()
static int ldisc_open(struct tty_struct *tty)
{
...
ser->tty = tty_kref_get(tty);
...
result = register_netdevice(dev);
if (result) {
rtnl_unlock();
free_netdev(dev);
return -ENODEV;
}
...
}
Ser pointer is netdev private_data, so after free_netdev()
this pointer goes away with unputted tty reference. So, fix
it by adding tty_kref_put() before freeing netdev.
Reported-and-tested-by: syzbot+f303e045423e617d2cad@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da9ef50f545f86ffe6ff786174d26500c4db737a ]
Current logic is performing hard reset and causing the programmed
registers to be wiped out.
as per datasheet: https://www.ti.com/lit/ds/symlink/dp83867cr.pdf
8.6.26 Control Register (CTRL)
do SW_RESTART to perform a reset not including the registers,
If performed when link is already present,
it will drop the link and trigger re-auto negotiation.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Geet Modi <geet.modi@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd18de517923903a177508fc8813f44e717b1c00 ]
Syzbot reports that we may be able to get into a situation where
mac80211 has pending ACK frames on shutdown with hwsim. It appears
that the reason for this is that syzbot uses the wmediumd hooks to
intercept/injection frames, and may shut down hwsim, removing the
radio(s), while frames are pending in the air simulation.
Clean out the pending queue when the interface is stopped, after
this the frames can't be reported back to mac80211 properly anyway.
Reported-by: syzbot+a063bbf0b15737362592@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210517170429.b0f85ab0eda1.Ie42a6ec6b940c971f3441286aeaaae2fe368e29a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8f269102baf788aecfcbbc6313b6bceb54c9b990 upstream.
Platform drivers may call stmmac_probe_config_dt() to parse dt, could
call stmmac_remove_config_dt() in error handing after dt parsed, so need
disable clocks in stmmac_remove_config_dt().
Go through all platforms drivers which use stmmac_probe_config_dt(),
none of them disable clocks manually, so it's safe to disable them in
stmmac_remove_config_dt().
Fixes: commit d2ed0a7755fe ("net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c364df2489b8ef2f5e3159b1dff1ff1fdb16040d upstream.
Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.
This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.
Fixes: 84823ff80f74 ("net: ll_temac: Fix race condition causing TX hang")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aa32217a9a446275440ee8724b1ecaf1838df47 upstream.
With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.
Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91c02557174be7f72e46ed7311e3bea1939840b0 upstream.
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.
In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.
Fail log:
| [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected
| [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem)
So, all allocated buffers should be freed with usb_free_coherent()
explicitly
NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9cca0c2d70149160407bda9a9446ce0c29b6e6c6 ]
static void ec_bhf_remove(struct pci_dev *dev)
{
...
struct ec_bhf_priv *priv = netdev_priv(net_dev);
unregister_netdev(net_dev);
free_netdev(net_dev);
pci_iounmap(dev, priv->dma_io);
pci_iounmap(dev, priv->io);
...
}
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls.
Fixes: 6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03400aaa69f916a376e11526cf591901a96a3a5c ]
bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.
Fixes: 7c3809181468 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0afd6a4e8028cc487c240b6cfe04094e45a306e4 ]
There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset. This can cause
some PHY related functionalities to fail after a firmware reset. For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.
Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3b26fdf1b32f91c7a3bc743384b4a298ab53ad7 ]
when usbnet transmit a skb, eem fixup it in eem_tx_fixup(),
if skb_copy_expand() failed, it return NULL,
usbnet_start_xmit() will have no chance to free original skb.
fix it by free orginal skb in eem_tx_fixup() first,
then check skb clone status, if failed, return NULL to usbnet.
Fixes: 9f722c0978b0 ("usbnet: CDC EEM support (v5)")
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c19c8c0e666f9259e2fc4d2fa4b9ff8e3b40ee5d ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: d6b6d9877878 ("be2net: use PCIe AER capability")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d23765646e71b43ed2b809930411ba5c0aadee7b ]
Commit da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.")
refactor the fec_devtype, need adjust ptp driver accordingly.
Fixes: da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56b786d86694e079d8aad9b314e015cd4ac02a3d ]
The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].
This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL.
Fixes: 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ea6cd16f1599c1eac6018751eadbc5fc736b99a ]
The previous commit didn't fix the bug properly. By mistake, it replaces
the pointer of the next skb in the descriptor ring instead of the current
one. As a result, the two descriptors are assigned the same SKB. The error
is seen during the iperf test when skb_put tries to insert a second packet
and exceeds the available buffer.
Fixes: c7718ee96dbc ("net: lantiq: fix memory corruption in RX ring ")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1a3d4067309451e68c33dbd356032549cc0bd8e ]
This is meant to make the host side cdc_ncm interface consistently
named just like the older CDC protocols: cdc_ether & cdc_ecm
(and even rndis_host), which all use 'FLAG_ETHER | FLAG_POINTTOPOINT'.
include/linux/usb/usbnet.h:
#define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */
#define FLAG_WLAN 0x0080 /* use "wlan%d" names */
#define FLAG_WWAN 0x0400 /* use "wwan%d" names */
#define FLAG_POINTTOPOINT 0x1000 /* possibly use "usb%d" names */
drivers/net/usb/usbnet.c @ line 1711:
strcpy (net->name, "usb%d");
...
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strcpy (net->name, "eth%d");
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strcpy(net->name, "wlan%d");
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strcpy(net->name, "wwan%d");
So by using ETHER | POINTTOPOINT the interface naming is
either usb%d or eth%d based on the global uniqueness of the
mac address of the device.
Without this 2.5gbps ethernet dongles which all seem to use the cdc_ncm
driver end up being called usb%d instead of eth%d even though they're
definitely not two-host. (All 1gbps & 5gbps ethernet usb dongles I've
tested don't hit this problem due to use of different drivers, primarily
r8152 and aqc111)
Fixes tag is based purely on git blame, and is really just here to make
sure this hits LTS branches newer than v4.5.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 4d06dd537f95 ("cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49a10c7b176295f8fafb338911cf028e97f65f4d ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: e87ad5539343 ("netxen: support pci error handlers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb3376604a676e0302258b01893911bdd7aa5278 ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 451724c821c1 ("qlcnic: aer support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1adb20f0d496b2c61e9aa1f4761b8d71f93d258e ]
The register starts from 0x800 is the 16th MAC address register rather
than the first one.
Fixes: cffb13f4d6fb ("stmmac: extend mac addr reg and fix perfect filering")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33e381448cf7a05d76ac0b47d4a6531ecd0e5c53 ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: ab69bde6b2e9 ("alx: add a simple AR816x/AR817x device driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d6727dddc7f93fcc155cb8d0c49c29ae0e71122 ]
The device is able to offload either the outer header csum or inner
header csum. The driver utilizes the inner csum offload. Hence, block
setting of tx-udp_tnl-csum-segmentation and set it to off[fixed].
Fixes: b49663c8fb49 ("net/mlx5e: Add support for UDP tunnel segmentation with outer checksum offload")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1718505d7f67ee0ab051322f1cbc7ac42b5da82 ]
since mlx5 hardware can segment correctly TSO packets on VXLAN over VLAN
topologies, CPU usage can improve significantly if we enable tunnel
offloads in dev->vlan_features, like it was done in the past with other
NIC drivers (e.g. mlx4, be2net and ixgbe).
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c189716b2a7c1d2d8658e269735273caa1c38b54 ]
Check if RoCE is supported by the device before enable it in
the vport context and create all the RDMA steering objects.
Fixes: 80f09dfc237f ("net/mlx5: Eswitch, enable RoCE loopback traffic")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ad893e516a77209a1818a2072d2027d87db809f ]
Currently, IPsec feature is disabled because mlx5e_build_nic_netdev
is required to be called after mlx5e_ipsec_init. This requirement is
invalid as mlx5e_build_nic_netdev and mlx5e_ipsec_init initialize
independent resources.
Remove ipsec pointer check in mlx5e_build_nic_netdev so that the
two functions can be called at any order.
Fixes: 547eede070eb ("net/mlx5e: IPSec, Innova IPSec offload infrastructure")
Signed-off-by: Huy Nguyen <huyn@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2386cf7c5f4ff5d7b584f5d92014edd7df6c676 ]
This patch fixes TX hangs with threaded NAPI enabled. The scheduled
NAPI seems to be executed in parallel with the interrupt on second
thread. Sometimes it happens that ltq_dma_disable_irq() is executed
after xrx200_tx_housekeeping(). The symptom is that TX interrupts
are disabled in the DMA controller. As a result, the TX hangs after
a few seconds of the iperf test. Scheduling NAPI after disabling
interrupts fixes this issue.
Tested on Lantiq xRX200 (BT Home Hub 5A).
Fixes: 9423361da523 ("net: lantiq: Disable IRQs only if NAPI gets scheduled ")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bb392f62447d73cc7dd7562413a2cd9104c82f8 ]
My initial goal was to fix the default MTU, which is set to 65536, ie above
the maximum defined in the driver: 65535 (ETH_MAX_MTU).
In fact, it's seems more consistent, wrt min_mtu, to set the max_mtu to
IP6_MAX_MTU (65535 + sizeof(struct ipv6hdr)) and use it by default.
Let's also, for consistency, set the mtu in vrf_setup(). This function
calls ether_setup(), which set the mtu to 1500. Thus, the whole mtu config
is done in the same function.
Before the patch:
$ ip link add blue type vrf table 1234
$ ip link list blue
9: blue: <NOARP,MASTER> mtu 65536 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether fa:f5:27:70:24:2a brd ff:ff:ff:ff:ff:ff
$ ip link set dev blue mtu 65535
$ ip link set dev blue mtu 65536
Error: mtu greater than device maximum.
Fixes: 5055376a3b44 ("net: vrf: Fix ping failed when vrf mtu is set to 0")
CC: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f336d0b93ae978f12c5e27199f828da89b91e56a ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'status'.
Eliminate the follow smatch warning:
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:3818 myri10ge_probe()
warn: missing error code 'status'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 404e5a12691fe797486475fe28cc0b80cb8bef2c upstream.
Currently when mlx4 maps the hca_core_clock page to the user space there
are read-modifiable registers, one of which is semaphore, on this page as
well as the clock counter. If user reads the wrong offset, it can modify
the semaphore and hang the device.
Do not map the hca_core_clock page to the user space unless the device has
been put in a backwards compatibility mode to support this feature.
After this patch, mlx4 core_clock won't be mapped to user space on the
majority of existing devices and the uverbs device time feature in
ibv_query_rt_values_ex() will be disabled.
Fixes: 52033cfb5aab ("IB/mlx4: Add mmap call to map the hardware clock")
Link: https://lore.kernel.org/r/9632304e0d6790af84b3b706d8c18732bc0d5e27.1622726305.git.leonro@nvidia.com
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c42a49738f16af0061f9ae5c2f5a955f268d9e3 ]
Also enable phy errata workaround on 9567 since has the same errata as
the 9477 according to the manufacture's documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4dd4fc6105e54393d637450a11d4cddb5fabc4f ]
In cops_probe1(), there is a write to dev->base_addr after requesting an
interrupt line and registering the interrupt handler cops_interrupt().
The handler might be called in parallel to handle an interrupt.
cops_interrupt() tries to read dev->base_addr leading to a potential
data race. So write to dev->base_addr before calling request_irq().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Saubhik Mukherjee <saubhik.mukherjee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eff1461a6dec84f04fafa9128548bad51d96147 ]
If runtime power menagement is enabled, the gigabit ethernet PLL would
be disabled after macb_probe(). During this period of time, the system
would hang up if we try to access GEMGXL control registers.
We can't put runtime_pm_get/runtime_pm_put/ there due to the issue of
sleep inside atomic section (7fa2955ff70ce453 ("sh_eth: Fix sleeping
function called from invalid context"). Add netif_running checking to
ensure the device is available before accessing GEMGXL device.
Changed in v2:
- Use netif_running instead of its own flag
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dde47a66d4fb181830d6fa000e5ea86907b639e ]
We spotted a bug recently during a review where a driver was
unregistering a bus that wasn't registered, which would trigger this
BUG_ON(). Let's handle that situation more gracefully, and just print
a warning and return.
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
