Currently there is a mx31ads BSP file in the kernel, but no default
config file.
This patch adds a basic default config for the imx31ads but it is for test
purposes only to ensure the i.MX2 patch stack doesn't break the i.MX3.
Note: For reference only. This configuration is untested as I have
no access to an mx31ads.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
The S3C2410 serial driver in drivers/serial/s3c2410.c has been
growing bigger with the addition of more variants of this hardware
with the growing Samsung SoCs range. As such, it would be
easier to split this code up into a core and per-cpu drivers to
make driver addition easier, and the core smaller.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Enable SCSI support, mainly to help with adding
USB storage support later and for the imminent
changes for libata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the following to the networking confgiuration:
1) Packet socket support (useful for userland dhcp)
2) Add bluetooth and USB bluetooth drivers as modules
3) Add basic IPv6 support as modules.
4) Add the wireless core as modules.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Enable new filesystem options, such as:
- JFFS2 summary nodes
- Ext2/3 externed options
- Standard CDROM filesystems
Also add NTFS as a module.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Combine cm_x270_defconfig and em_x270_defconfig to allow running the
same kernel on both machines
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the help text for RTC_DRV_AT91SAM9 to mention that the
option apply to AT91CAP9 processors too, and enable it in the
defconfig.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is patch 2 of 2 adding support for the USB High Speed Device Port
on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP
as the AVR32 and the AT91SAM9RL.
This patch declares the UDPHS ressources in the at91cap9 (cpu and
adk board) files, wires up the atmel_usba_udc driver to them,
and activates the driver in the defconfig.
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Default config files for the three AT91-based boards available from
Calao Systems: USB_A9260, USB_A9263 and QIL_A9260.
Signed-off-by: Grégory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dyntick is superseded by the clocksource/clockevent infrastructure,
using the NO_HZ configuration option. No one implements dyntick on
ARM anymore, so it's pointless keeping it around. Remove dyntick
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the include of the GPIO header needed to make gumstix
build. The defconfig is updated to 2.6.25 and disables PCMCIA since
that has not yet been implemented for gumstix.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables LEDs and the 1-wire bus (connected to
a DS2760 battery monitor) on the magician.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This enables rootfs on StrataFlash if the bootloader supplies the
partition list.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
needed for power management (audio, BT, charging, GSM, LCD, SD), GSM, flash and SD operation and audio routing.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements support for Gumstix-F flash, udc and mci. Fixes since the last time are:
- Steve Sakoman as maintainer
- cleanup for udc and mci setup
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the TinCanTools Hammer board to list of supported machines in the
arch/arm/mach-s3c2410 directory, as well as a default config entry. the
mach-tct_hammer.c file initializes basic i/o, clocks, irqs, as well as
the mtd flash layout if enabled in the kernel configuration.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the emQbit ECB_AT91 board.
<http://wiki.emqbit.com/free-ecb-at91>
Original patch from Nelson Castillo.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Olimex SAM9-L9260 board.
<http://www.olimex.com/dev/sam9-L9260.html>
Original patch from Ivan Vasilev.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Kwikbyte KB9260 (CAM60) board.
<http://www.kwikbyte.com/KB9260.html>
Original patch from Kwikbyte.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Updates the CSB637 platform's D1/PB2 LED to use gpio-led by default.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the default configuration for the following AT91-based boards:
Embest ATEB9200
Cogent CSB337
Cogent CSB637
Sperry-Sun KAFA
Picotux200
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the default configuration for the following AT91-based boards:
Atmel AT91RM9200 DK
Atmel AT91RM9200 EK
Atmel AT91SAM9260 EK
Atmel AT91SAM9261 EK
Atmel AT91SAM9263 EK
Atmel AT91SAM9RL EK
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Freecom-FSG3 is a small network-attached-storage device with the
following feature set:
* Intel IXP422
* 4MB Flash (ixp4xx flash driver)
* 64MB RAM
* 4 USB 2.0 host ports (ehci and ohci drivers)
* 1 WAN (eth1) and 3 LAN (eth0) ethernet ports
* Supported by the open source ixp4xx ethernet driver
* Via VT6421 disk controller (libata and sata-via drivers)
* Internal hard disk (PATA supported, SATA not yet supported)
* External SATA port (not yet supported)
* ISL1208 RTC chip
* Winbond 83782 temp sensor and fan controller
* MiniPCI slot
The ixp4xx_defconfig is also updated to support this device (the
leds-fsg driver is to be submitted separately via the leds tree after
this initial support is merged, as it depends on header gpio defines).
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- add all available mach types for ns9xxx even if the corresponding
variables don't exist yet.
- minimize such that only relevant variables are defined. For others the
default value is used.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
1. Configuration file for YL9200
2. Board file fro YL9200
Adds support for the UCdragon YL9200 board available widly in China
Signed-off-by: steve birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do a global s/orion/orion5x/ of the Orion 5x-specific bits (i.e.
not the plat-orion bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This allows monitoring compile issues with Kautobuild for
other omap1 boards until we have more board specific defconfig
files.
After 2.6.25, we can add a generic config_omap_generic16xx to
compile in support for all 16xx boards and then remove other
boards from OSK defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master:
[ARM] constify function pointer tables
[ARM] 4823/1: AT91 section fix
[ARM] 4824/1: pxa: clear RDH bit after any reset
[ARM] pxa: remove debugging PM: printk
* omap1-upstream:
ARM: OMAP1: Misc clean-up
ARM: OMAP1: Update defconfigs for omap1
ARM: OMAP1: Palm Tungsten E board clean-up
ARM: OMAP1: Use I2C bus registration helper for omap1
ARM: OMAP1: Remove omap_sram_idle()
ARM: OMAP1: PM fixes for OMAP1
ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
ARM: OMAP1: Make omap1 use MMC multislot structures
ARM: OMAP1: Change the comments to C style
ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
ARM: OMAP: Add helper module for board specific I2C bus registration
ARM: OMAP: Add dmtimer support for OMAP3
ARM: OMAP: Pre-3430 clean-up for dmtimer.c
ARM: OMAP: Add DMA support for chaining and 3430
ARM: OMAP: Add 24xx GPIO debounce support
ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
ARM: OMAP: Add 3430 gpio support
ARM: OMAP: Add 3430 CPU identification macros
ARM: OMAP: Request DSP memory for McBSP
* orion:
[ARM] Orion: Use the sata_mv driver for the TS-209 SATA
[ARM] Orion: Use the sata_mv driver for the Kurobox SATA
[ARM] Orion: free up kernel virtual address space
[ARM] Orion: distinguish between physical and virtual addresses
[ARM] Orion: kill orion_early_putstr()
[ARM] Orion: update defconfig
[ARM] Orion: Use the sata_mv driver for the integrated SATA controller
Make omap1 use new MMC multislot structures. The related MMC
patches will be sent separately.
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br>
Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: David Cohen <david.cohen@indt.org.br>
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enables the new ixp4xx qmgr and npe drivers in ixp4xx_defconfig.
Sets up the corresponding platform data for the nslu2 and nas100d
boards, and reads the ethernet MAC address from the internal flash.
Tested on both little-endian and big-endian kernels.
Tested-by: Tom King <tom@websb.net>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Michael Westerhof <mwester@dls.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
