With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d946092000698fd204d82a9d239103c656fb63bf
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Tested on my Beagle XM.
v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
but have no place in the kernel proper.
This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.
We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.
Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.
Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.
Reported-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a4910b744486254cfa61995954c118fb2283c4fd has broken promiscuous
mode, which is never set. port->promisc just reflects the last setting
of PROMISCUOUS mode to avoid doing an extra hypercall when it's already
set.
However, since it may fail because of hypervisor permissions, we should
still respect the multicast settings and not simply exit after setting
promiscuous mode.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug in the mask of regtype parameter for registering a
multicast filter. It was ignoring the scope bit, which was wrongly being
used for all filters. The SCOPE_ALL value adds a filter that allows all
multicast packets and ignores the MAC parameter, just what allmulticast
needs. The normals filters, however, should not use SCOPE_ALL.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case. This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes this beauty into a statement that actually has an effect on amd64.
Tested-by: Per Jessen <per@opensuse.org>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the original patch from Ying Cai <ycai@google.com>
This change ensures that the itr/itr_setting adjustment logic is used,
even for the default/compiled-in value.
Context:
When we changed the default InterruptThrottleRate value from default
(3 = dynamic mode) to 8000 for example, only adapter->itr_setting
(which controls interrupt coalescing mode) was set to 8000, but
adapter->itr (which controls the value set in NIC register) was not
updated accordingly. So from ethtool, it seemed the interrupt
throttling is enabled at 8000 intr/s, but the NIC actually was
running in dynamic mode which has lower CPU efficiency especially
when throughput is not high.
CC: Ying Cai <ycai@google.com>
CC: David Decotigny <david.decotigny@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
This patch fixes this problem by increasing the msleep from 50 to 100.
Signed-off-by: Prasanna S Panchamukhi <ppanchamukhi@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.
Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.
Note that we don't use queues 20 and higher today and
doing so needs more work than this.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:
net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found
Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.
Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.
This causes crashes in some situations:
[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f7936c01d5b426c03a691eca082b03f2b9.
Tested on ARM/Beagle.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
From the code comment I understand that this something that can -
and does, quite frequently - happen.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution. Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:
Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.
After that you need to reload the driver to get it working again.
This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097https://bugzilla.redhat.com/show_bug.cgi?id=802106
This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.
This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852e4345d0a31af593c46738ca8614bff
(ath9k_hw: Cleanup TX power calculation for AR9287).
Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.
Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.
Fix this by adding the missing call of the helper
function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to unifying regulatory limit handling
commit ca2c68cc7bc80fc4504fb420df04cce99c9ee6ec
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.
This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.
This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refrain from attempting to free an interrupt line if the request
fails and hence, there is no IRQ to free.
CC: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_id parameter passed to free_irq needs to match the one passed
to the corresponding request_irq.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the network interface is down, the RX packets number which
could be observed by ifconfig may keep on increasing.
This is because the WORK scheduled in netvsc_set_multicast_list()
may be executed after netvsc_close(). That means the rndis filter
may be re-enabled by do_set_multicast() even if it was closed by
netvsc_close().
By canceling possible WORK before close the rndis filter, the issue
could be never happened.
Signed-off-by: Wenqi Ma <wenqi_ma@trendmicro.com.cn>
Reviewed-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential deadlock scenario when the ks8851 driver
is removed. The interrupt handler schedules a workqueue which
acquires a mutex that ks8851_net_stop() also acquires before
flushing the workqueue. Previously lockdep wouldn't be able
to find this problem but now that it has the support we can
trigger this lockdep warning by rmmoding the driver after
an ifconfig up.
Fix the possible deadlock by disabling the interrupts in
the chip and then release the lock across the workqueue
flushing. The mutex is only there to proect the registers
anyway so this should be ok.
=======================================================
[ INFO: possible circular locking dependency detected ]
3.0.21-00021-g8b33780-dirty #2911
-------------------------------------------------------
rmmod/125 is trying to acquire lock:
((&ks->irq_work)){+.+...}, at: [<c019e0b8>] flush_work+0x0/0xac
but task is already holding lock:
(&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&ks->lock){+.+...}:
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c083dbec>] mutex_lock_nested+0x68/0x3dc
[<bf00bd48>] ks8851_irq_work+0x24/0x46c [ks8851]
[<c019c580>] process_one_work+0x2d8/0x518
[<c019cb98>] worker_thread+0x220/0x3a0
[<c01a2ad4>] kthread+0x88/0x94
[<c0107008>] kernel_thread_exit+0x0/0x8
-> #0 ((&ks->irq_work)){+.+...}:
[<c01b7984>] validate_chain+0x914/0x1018
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c019e104>] flush_work+0x4c/0xac
[<bf00b858>] ks8851_net_stop+0x6c/0x138 [ks8851]
[<c06b209c>] __dev_close_many+0x98/0xcc
[<c06b2174>] dev_close_many+0x68/0xd0
[<c06b22ec>] rollback_registered_many+0xcc/0x2b8
[<c06b2554>] rollback_registered+0x28/0x34
[<c06b25b8>] unregister_netdevice_queue+0x58/0x7c
[<c06b25f4>] unregister_netdev+0x18/0x20
[<bf00c1f4>] ks8851_remove+0x64/0xb4 [ks8851]
[<c049ddf0>] spi_drv_remove+0x18/0x1c
[<c0468e98>] __device_release_driver+0x7c/0xbc
[<c0468f64>] driver_detach+0x8c/0xb4
[<c0467f00>] bus_remove_driver+0xb8/0xe8
[<c01c1d20>] sys_delete_module+0x1e8/0x27c
[<c0105ec0>] ret_fast_syscall+0x0/0x3c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ks->lock);
lock((&ks->irq_work));
lock(&ks->lock);
lock((&ks->irq_work));
*** DEADLOCK ***
4 locks held by rmmod/125:
#0: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f44>] driver_detach+0x6c/0xb4
#1: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f50>] driver_detach+0x78/0xb4
#2: (rtnl_mutex){+.+.+.}, at: [<c06b25e8>] unregister_netdev+0xc/0x20
#3: (&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC77xx devices can operate in two modes: "Direct IP" or "QMI",
switchable using a password protected AT command. Both product ID
and USB interface configuration will change when switched.
The "sierra_net" driver supports the "Direct IP" mode. This driver
supports the "QMI" mode.
There are also multiple possible USB interface configurations in each
mode, some providing more than one wwan interface. Like many other
devices made for Windows, different interface types are identified
using a static interface number. We define a Sierra specific
interface whitelist to support this.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sp_pri_to_cos[] array size depends on the config but lets say it is
BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also
DCBX_E3B0_MAX_NUM_COS_PORT0. In the original code
"pri == max_num_of_cos" was accepted but it is one past the end of the
array.
Also we used "pri" before capping it. It's a harmless read past the end
of the array, but it would affect which error message gets printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_ADDR_LEN is 32. ETH_ALEN is 6. mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array. I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free card->mem in the error-handling code since it was successfully
allocated just above.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy load (flood ping) it is possible for the MDIO timeout to
expire before the loop checks the GO bit again. This patch adds an
additional check whether the operation was done before actually
returning -ETIMEDOUT.
To reproduce this bug, flood ping the device, e.g., ping -f -l 1000
After some time, a "timed out waiting for user access" warning
may appear. And even worse, link may go down since the PHY reported a
timeout.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arcrimi_probe() calls BUGMSG() before register_netdev() happens. BUGMSG()
itself prints dev->name, but as the format string hasn't been expanded by
register_netdev() yet, the output contains bogus device name such as
arc%d: Given: node 00h, shmem 0h, irq 0
As we don't know the device name yet, just drop the prefix completely from
the debugging messages.
Reported-by: Steven Young <sdyoung@vt220.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that we identify FCoE rings earlier than
ixgbe_set_rx_buffer_len. Instead we identify the Rx FCoE rings at
allocation time in ixgbe_alloc_q_vector.
The motivation behind this change is to avoid memory corruption when FCoE
is enabled. Without this change we were initializing the rings at 0, and
2K on systems with 4K pages, then when we bumped the buffer size to 4K with
order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K.
This was resulting in memory corruptions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in
netif_set_real_num_tx_queues(). The call stack is:
netif_set_real_num_tx_queues
ixgbe_set_num_queues
ixgbe_init_interrupt_scheme
ixgbe_resume
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Assigning sequence number for frames without taking care
of the fragment field breaks transmission of fragmented frames.
Fix this by assigning the fragment number properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
