Spidernet was the driver I original did all the node-aware netdevice
allocation for, but after a year it still hasn't hit mainline.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware must not see that is given ownership of a buffer until it is
completely written, and when the driver receives ownership of a buffer,
it must ensure that any other reads to the buffer reflect its final
state. Thus, I/O barriers are added where required.
Without this patch, I have observed GCC reordering the setting of
bdp->length and bdp->status in gfar_new_skb. Hardware reordering
was also theoretically possible.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix link speed detection change.
Thanks to Stefan Roese <sr@denx.de> for finding this bug.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Original patch is from Jeff Haran <jharan@brocade.com> with my minor style
fixes. His comments follow:
The first problem was in the function that configures the PHY for
autonegotiation, genmii_setup_aneg(). The original code does a
read/modify/write of the autonegotiation advertizement register (reg 4),
followed by a read/modify/write of the control register (reg 0). While
the original code follows the proper procedure as per reading the IEEE
specs, what I found is that on at least one PHY model (National DP83843)
the read of the control register comes back with the soft reset bit set
(bit 15). Because of the read/modify/write operation, this causes the
write to write a 1 back to the reset bit, which initiates a software
reset of the PHY. This software reset causes the PHY to return to its
power up state which advertizes all modes of operation, thus negating
the write to the autoneg advertizement register. The modification is to
spin reading the control register until the soft reset bit is clear
before doing the modify/write.
The second problem was in the function that configures the PHY for
forced operation, genmii_setup_forced(). The original code initiates a
software reset operation via a write of a 1 to bit 15 of the control
register (reg 0), but then proceeds to do a second write to that same
register without waiting until that reset bit is cleared by the PHY
itself (which according to the IEEE specs indicates that the PHY reset
is complete). This is a violation of how one is supposed to use this
software reset feature of these PHYs and I believe was the cause of
mysterious, difficult to reproduce link failures that we've observed on
some of our systems that use this driver. The fix is to modify the
function so that it spins waiting for the reset bit to clear after doing
the soft reset and before doing the subsequent write.
Signed-off-by: Jeff Haran <jharan@brocade.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.
Signed-off-by: Stephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The problems with Gigabyte motherboards are system configuration dependent.
Since it works fine for some users, it doesn't make sense to deprive
them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.
This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.
It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch add new sub-device-id to support new adapter and changed the
interrupt irq number for unsigned char to unsigned int.
[akpm@osdl.org: fix whitespace in device table]
Signed-off by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make drivers/rtc/Kconfig be clearer about what the various "interfaces"
actually mean, by showing path names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typo which breaks build. How did that happen?
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refine SCREEN_INFO sanity check for vgacon initialization.
Checking video mode field only to see whenever SCREEN_INFO is
initialized is not enougth, in some cases it is zero although
a vga card is present. Lets additionally check cols and lines.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Alan <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Strip __cpuinit[data] from Node <-> PXM routines and supporting data
structures. Also make pxm_to_node_map and node_to_pxm_map local to the
numa acpi module.
This fixes a bug triggered by the following conditions:
- boot on a machine with a SLIT table defined
- kernel is configured w/ CONFIG_HOTPLUG_CPU=n
- cat /sys/devices/system/node/node*/distance
This will cause an oops by calling into a freed memory section.
In particular, on x86_64, __node_distance calls node_to_pxm().
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/macintosh/windfarm_core.c: In function 'wf_register_control':
drivers/macintosh/windfarm_core.c:219: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/windfarm_core.c: In function 'wf_register_sensor':
drivers/macintosh/windfarm_core.c:329: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The early kernel parameter is wdt and not wdt_enable. according to
arch/powerpc/kernel/setup_32.c.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: track spindown status and skip spindown_compat if possible
libata: fix shutdown warning message printing
libata-acpi: add ATA_FLAG_ACPI_SATA port flag
libata: during revalidation, check n_sectors after device is configured
libata: separate out ata_dev_reread_id()
pata_scc had been missed by ata_std_prereset() switch
alpha:
drivers/parport/parport_pc.c: In function 'parport_pc_fifo_write_block_dma':
drivers/parport/parport_pc.c:636: warning: implicit declaration of function 'dma_map_single'
drivers/parport/parport_pc.c:637: error: 'DMA_TO_DEVICE' undeclared (first use in this function)
drivers/parport/parport_pc.c:637: error: (Each undeclared identifier is reported only once
drivers/parport/parport_pc.c:637: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
find_first_zero_bit accepts number of bits, not longs.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A fix for a really stupid typo in the KS8695 serial driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our assumption that most distros issue STANDBYNOW seems wrong. The
upstream sysvinit and thus many distros including gentoo and opensuse
don't take any action for libata disks on spindown. We can skip
compat handling for these distros so that they don't need to update
anything to take advantage of kernel-side shutdown.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unlocking ap->lock and ssleeping don't work because SCSI commands can
be issued from completion path without context. Reimplement delayed
completion by allowing translation functions to override
qc->scsidone(), storing the original completion function to
scmd->scsi_done() and overriding qc->scsidone() with a function which
schedules delayed invocation of scmd->scsi_done().
This isn't pretty at all but all the ugly parts are thankfully
contained in the stop translation path where the compat feature is
implemented.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Whether a controller needs IDE or SATA ACPI hierarchy is determined by
the programming interface of the controller not by whether the
controller is SATA or PATA, or it supports slave device or not. This
patch adds ATA_FLAG_ACPI_SATA port flags which tells libata-acpi that
the port needs SATA ACPI nodes, and sets the flag for ahci and
sata_sil24.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Device might be resized during ata_dev_configure() due to HPA or
(later) ACPI _GTF. Currently it's worked around by caching n_sectors
before turning off HPA. The cached original size is overwritten if
the device is reconfigured without being hardreset - which always
happens after configuring trasnfer mode. If the device gets hardreset
for some reason after that, revalidation fails with -ENODEV.
This patch makes size checking more robust by moving n_sectors check
from ata_dev_reread_id() to ata_dev_revalidate() after the device is
fully configured. No matter what happens during configuration, a
device must have the same n_sectors after fully configured to be
treated as the same device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_dev_reread_id() from ata_dev_revalidate().
ata_dev_reread_id() reads IDENTIFY page and determines whether the
same device is still there. ata_dev_revalidate() reconfigures after
reread completes. This will be used by ACPI update.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hypervisor interfaces need to be negotiated in order to use
some API calls reliably. So add a small set of interfaces
to request API versions and query current settings.
This allows us to fix some bugs in the hypervisor console:
1) If we can negotiate API group CORE of at least major 1
minor 1 we can use con_read and con_write which can improve
console performance quite a bit.
2) When we do a console write request, we should hold the
spinlock around the whole request, not a byte at a time.
What would happen is that it's easy for output from
different cpus to get mixed with each other.
3) Use consistent udelay() based polling, udelay(1) each
loop with a limit of 1000 polls to handle stuck hypervisor
console.
Signed-off-by: David S. Miller <davem@davemloft.net>
.. because video-buf.c requires PCI, and VIDEO_EM28XX selects it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
stuff that does select USB should depend on USB_ARCH_HAS_HCD, or we'll
end up with unbuildable configs.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
need it for page_private(), not all targets have it pulled indirectly
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
Use menuconfig objects: IDE
sl82c105: Switch to ref counting API
ide: remove ide_use_dma()
ide: add missing validity checks for identify words 62 and 63
ide: remove ide_dma_enable()
sl82c105: add speedproc() method and MWDMA0/1 support
cs5530/sc1200: add ->speedproc support
cs5530/sc1200: DMA support cleanup
ide: use ide_tune_dma() part #2
cs5530/sc1200: add ->udma_filter methods
ide: always disable DMA before tuning it
pdc202xx_new: use ide_tune_dma()
alim15x3: use ide_tune_dma()
sis5513: PIO mode setup fixes
serverworks: PIO mode setup fixes
pdc202xx_old: rewrite mode programming code (v2)
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Not sure how this one got missed in the great purge some time ago but it did.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add the speedproc() method for setting transfer modes, modify config_for_dma()
to call it and use ide_max_dma_mode() to select the best DMA mode.
Add support for the multiword DMA modes 0 and 1, using the upper half of the
'drive_data' field to store the DMA timings to program into the drive control
register when DMA is turned on for real.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add {cs5530,sc1200}_tunepio() for programming PIO timings
* add {cs5530,sc1200}_tune_chipset() (->speedproc method) for setting
transfer mode and convert {cs5530,sc1200}_config_dma() to use it
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
sc1200.c:
* remove open-coded variant of ide_dma_host_off() (== ->dma_host_off),
it is not needed because ->dma_off_quietly calls ->dma_host_off
* use ->dma_host_on (== ide_dma_host_on() for this driver) instead of
open-coded variant, call it from the users of sc1200_config_dma2()
[ there is no need to call ->dma_host_on in sc1200_config_dma() because
core code takes care of calling ->ide_dma_on on successful execution
of ->ide_dma_check ]
* add comment about ->tuneproc interface abuse
cs5530.c/sc1200.c:
* core code takes care of calling ->dma_off_quietly before calling
->ide_dma_check so there is no need to call it in ->ide_dma_check methods
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CS5530/SC1200 specifies that two drives on the same cable cannot mix
UDMA/MDMA. Add {cs5530,sc1200}_udma_filter() to handle this. This also
makes it possible to remove open-coded best DMA mode selection and use
standard ide_use_dma()/ide_max_dma_mode() helpers. While at it bump
version numbers.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_start_power_step() and set_using_dma() were missing ->dma_off_quietly
call (comment in probe_hwif() states that DMA should be always cleared before
tuning is attempted). Fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove code enabling IORDY and prefetch from config_chipset_for_dma(),
as the comment states it has no real effect because these settings are
overriden when the PIO mode is set (and for this driver ->autotune == 1
so PIO mode is always programmed)
* use ide_tune_dma() in pdcnew_config_drive_xfer_rate() and remove no longer
needed config_chipset_for_dma()
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_tune_dma() in ali15x3_config_drive_for_dma() and remove all the open
coded DMA tuning code and also config_chipset_for_dma(). Set ->atapi_dma flag
correctly in init_hwif_common_ali15x3() so ide_tune_dma() can take care of
checking if ATAPI DMA is allowed and remove open coded ATAPI DMA check from
ali15x3_config_drive_for_dma().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to program PIO5 by config_art_rwp_pio() could result in incorrect PIO
timings being programmed and possibly the data corruption (for < ATA100
family chipsets PIO0 timings were used, for ATA100 and ATA100a - the random
content of test1 variable was used, for ATA133 - MWDMA0 timings were used)
* BUG() in sis5513_tune_chipset() if somebody tries to force unsupported PIO5,
also cleanup this function a bit while at it
* add comment about PIO0 timings for < ATA100 family chipsets
* remove open-coded best PIO mode selection from config_art_rwp_pio(),
it contained numerous bugs:
- it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
before using them
- it tried to found out maximum PIO mode basing on minimum IORDY cycle time
(moreover wrong cycle times were used for PIO1/5)
- it was overriding PIO blacklist and conservative PIO "downgrade" done
by ide_get_best_pio_mode()
* use sis5513_tune_drive() instead of config_art_rwp_pio()
in sis5513_config_xfer_rate() so the correct PIO mode is also set
on drive even if the device is not IORDY/DMA capable
* config_art_rwp_pio() was always setting the best possible mode and not
the wanted one - fix it and move ide_get_best_pio_mode() call to
config_chipset_for_pio()
* don't use ide_find_best_mode() in config_chipset_for_pio(), it was being
overriden by config_art_rwp_pio() for the host timings anyway + we need to
set the same PIO mode on the device and the host
* pass correct "pio" argument (255 instead of 5) to sis5513_tune_drive() call
in sis5513_config_xfer_rate() so the best PIO mode is set on the drive
and not PIO4
* rename sis5513_tune_drive() to sis5513_tuneproc()
and config_chipset_for_pio() to sis5513_tune_driver()
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to program PIO5 by svwks_tune_chipset() could result in incorrect PIO
timings being programmed and possibly the data corruption (it seems that
the minimum possible values were used but I lack the datasheets to be sure)
* select best PIO mode in svwks_tune_drive() and not in svwks_tune_chipset()
when doing PIO autotuning (pio == 255)
* don't try to tune PIO in config_chipset_for_dma() as ide_dma_enable() could
return 1 if DMA was previously enabled (svwks_config_drive_xfer_rate()
takes care of PIO tuning if no suitable DMA mode is found)
* remove config_chipset_for_pio() and use svwks_tune_drive() instead,
config_chipset_for_pio() contained numerous bugs when selecting PIO mode
(luckily it was only used for devices limited to PIO by capabilities/BIOS):
- it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
before using them
- it tried to found out maximum PIO mode basing on minimum IORDY cycle time
(moreover wrong cycle times were used for PIO0/1/5)
- it was overriding PIO blacklist and conservative PIO "downgrade" done
by ide_get_best_pio_mode()
- if the max drive PIO was PIO5 then XFER_PIO_0/XFER_PIO_SLOW was selected
(XFER_PIO_SLOW is not supported by svwks_tune_chipset() so the result
was the same as if using XFER_PIO_5 => wrong PIO timings were set)
- it was overriding drive->current_speed
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.
Rewrite mode programming code:
* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
even if both devices on the channel are not DMA capable and after reset
* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
as they need to be setup correctly also for PIO only devices, plus IORDY
wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
ATAPI devices
* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
(driver sets ->autotune to 1 so PIO modes are always programmed => lower
nibble of register A never equals 4 => "chipset_is_set" is always true)
* enable PIO mode programming for all ATAPI devices
(it was limited to ->media == ide_cdrom devices)
* remove extra reads of registers A/B/C, don't read register D et all
* do clearing / programming of registers A/B/C in one go
(gets rid of extra PCI config space read/write cycle)
* set initial values of drive_conf/AP/BP/CP variables to zero
(paranoia for the case when PCI reads fail)
* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
(ide_rate_filter() takes care of it)
* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)
* fix bitmasks for clearing bits of register B:
- when programming DMA mode bit 0x10 of register B was cleared which
resulted in overclocked PIO timing setting (iff PIO0 was used)
- when programming PIO mode bits 0x18 weren't cleared so suboptimal
timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)
* add FIXME comment about missing locking for 66MHz clock register
Also while at it:
* remove unused defines
* do a few cosmetic / CodingStyle fixes
* bump driver version
v2:
* in pdc202xx_tune_chipset() the old content of drive configuration
registers is used only by the debugging code so cover "drive_conf"
PCI registers read by #if PDC202XX_DEBUG_DRIVE_INFO
(Noticed by Sergei Shtylyov)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It was agreed that phy-connection-type was a better name for
the interface-type property, so this patch renames it.
Also, the max-speed property name was determined too generic,
and is therefore eliminated in favour of phy-connection-type
derivation logic.
includes corrections to copyright text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Looks like the new version of this patch has been overlooked,
so I'm resending it.
It just adapts the driver to the new IRQ API
according to what Russell has pointed out.
drivers/net/smc911x.c | 6 ++----
1 files changed, 2 insertions(+), 4 deletions(-)
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turns out we have an old version of firmware that stores the mac address
in 'mac-address' as a string instead of a byte array. All versions that
use local-mac-address should have it as byte array, so no need to do
string parsing for that case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This caused some very interesting behaviour depending on what happened to
be built at the same time. Add terminating empty entry to the list of IDs.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Interrupt ack fixes
Fix the packet count resets at interrupt time, using the cacheable
packet count status to set number of processed/received packets, since
the ack count is the cumulative number of packets processed, and not
incremental.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some shift values were obviously wrong. Fix them to correspond with
the masks.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB/cm: Optimize stale connection detection
IB/mthca: Set cleaned CQEs back to HW ownership when cleaning CQ
IB/mthca: Fix posting >255 recv WRs for Tavor
RDMA/cma: Add check to validate that cm_id is bound to a device
RDMA/cma: Fix synchronization with device removal in cma_iw_handler
RDMA/cma: Simplify device removal handling code
IB/ehca: Disable scaling code by default, bump version number
IB/ehca: Beautify sysfs attribute code and fix compiler warnings
IB/ehca: Remove _irqsave, move #ifdef
IB/ehca: Fix AQP0/1 QP number
IB/ehca: Correctly set GRH mask bit in ehca_modify_qp()
IB/ehca: Serialize hypervisor calls in ehca_register_mr()
IB/ipath: Shadow the gpio_mask register
IB/mlx4: Fix uninitialized spinlock for 32-bit archs
mlx4_core: Remove unused doorbell_lock
net: Trivial MLX4_DEBUG dependency fix.
This reverts commit f64da958df.
Andi Kleen is unhappy with the changes, and they really do not seem
worth it. IPMI could use DIE_NMI_IPI instead of the new callback, even
though that ends up having its own set of problems too, mainly because
the IPMI code cannot really know the NMI was from IPMI or not.
Manually fix up conflicts in arch/x86_64/kernel/traps.c and
drivers/char/ipmi/ipmi_watchdog.c.
Cc: Andi Kleen <ak@suse.de>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Corey Minyard <minyard@acm.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the presence of some running RX connections, we repeat
queue_delayed_work calls each 4 RX WRs, which is a waste. It's enough
to start stale task when a first passive connection is added, and
rerun it every IPOIB_CM_RX_DELAY as long as there are outstanding
passive connections.
This removes some code from RX data path.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_cq_clean() updates the CQ consumer index without moving CQEs
back to HW ownership. As a result, the same WRID might get reported
twice, resulting in a use-after-free. This was observed in IPoIB CM.
Fix by moving all freed CQEs to HW ownership.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=617>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix posting lists of > 255 receive WRs for Tavor: rq.next_ind must
be updated each doorbell, otherwise the next doorbell will use an
incorrect index.
Found by Ronni Zimmermann at Mellanox.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Several checks in the rdma_cm check against the state of the
cm_id, but only to validate that the cm_id is bound to an underlying
transport specific CM and an RDMA device. Make the check explicit
in what we're trying to check for, since we're not synchronizing
against the cm_id state.
This will allow a user to disconnect a cm_id or reject a connection
after receiving a device removal event.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cma_iw_handler needs to validate the state of the rdma_cm_id before
processing a new connection request to ensure that a device removal is
not already being processed for the same rdma_cm_id. Without the state
check, the user can receive simultaneous callbacks for the same cm_id, or
a callback after they've destroyed the cm_id.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new routine and rename another to encapsulate common code for
synchronizing with device removal.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Scaling code is still considered experimental, so disable it by default
- Increase version to SVNEHCA_0023
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA's sysfs attributes are now being created via sysfs_create_group(),
making the process neatly table-driven. The return value is checked, thus
fixing a few compiler warnings.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- In ehca_process_eq(), we're IRQ safe throughout the whole function, so we
don't need another _irqsave in the middle of flight.
- take_over_work() is only called by comp_pool_callback(), so it can move
into the same #ifdef block.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
AQP0/1 should report qp_num={0|1} and the actual QP# should be stored
in struct ehca_qp, not the other way round.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver needs to always supply the "GRH present" flag to the
hypervisor, whether it's true or false. Not supplying it (i.e. not
setting the corresponding mask bit) amounts to a "perhaps", which we
don't want.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some pSeries hypervisor versions show a race condition in the allocate
MR hCall. Serialize this call per adapter to circumvent this problem.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Once upon a time, GPIO interrupts were rare. But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception. This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips. Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on. An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.
Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
uar_lock spinlock was used in mlx4_ib_cq_arm without being initialized
(this only affects 32-bit archs, because uar_lock is not used on
64-bit archs and MLX4_INIT_DOORBELL_LOCK() is a NOP).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: fix PXA27x MMC workaround for bad CRC with 136 bit response
mmc: use assigned major for block device
sdhci: handle dma boundary interrupts
mmc: au1xmmc command types check from data flags
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Update defconfig.
[VIDEO]: XVR-500 and XVR-2500 need FB=y.
[SPARC32]: asm/system.h needs asm/smp.h
[SPARC32]: Update defconfig.
[SPARC32]: Fix sparc32 kdebug changes.
[SPARC64]: Accept ebus_bus_type for generic DMA ops.
[SPARC64]: Add missing cpus_empty() check in hypervisor xcall handling.
[SCSI]: Add help text for SCSI_ESP_CORE.
[SPARC] SBUS: display7seg.c needs asm/io.h
[SPARC] SBUS: bbc_i2c.c needs asm/io.h
[SPARC64]: Be more resiliant with PCI I/O space regs.
[SERIAL] SUNHV: Add an ID string.
... and make it depend on the response flag instead of the command type.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When the device hits certain memory boundaries, it signals an
interrupt and expects to be serviced. We don't need the feature
but we need to make sure the device doesn't stall.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch has changed command types check from data flags.
MMC_STOP_TRANSMISSION is never passed to au1xmmc_send_command().
SEND_STOP() is used for MMC_STOP_TRANSMISSION.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
there is a wrong id in drivers/char/agp/via-agp.c
#define PCI_DEVICE_ID_VIA_CX700 0x8324
It must be 0x0324
Notice that PCI_DEVICE_ID_VIA_CX700 is also used in
drivers/i2c/busses/i2c-viapro.c and
drivers/ide/pci/via82cxxx.c
So, I think that constant must be renamed to avoid conflicting.
I attached a proposed patch.
Signed-off-by: Dave Jones <davej@redhat.com>
... doh
Jeremy Fitzhardinge noted that the recent loop.c cleanups worked, but
cause lockdep to complain.
Ouch. OK, the deadlock is real and yes, I'm an idiot. Speaking of which,
we probably want to s/lock/pin/ in drivers/base/map.c to avoid such
brainos again. And yes, this stuff needs clear documentation. Will try
to put one together once I get some sleep...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_MLX4_DEBUG works out to a def_bool y for those that have
CONFIG_EMBEDDED set. Make it depend on MLX4_CORE.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When trying to load the ipmi_si module on a powerpc with no BMC (baseboard
management controller) the driver failes to load correctly, but doesn't
unregister itself from of_platform. So, on a second modprobe the kernel
crashes. This patch adds the missing unregister call.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a rather obvious error that Patrick found in the setup routines. Need to
set the proper address space in the ACPI case.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On PPC64, we need to include asm/prom.h for function definitions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flush the tty flip buffer when the line discipline input queue is flushed,
including the user call tcflush(TCIFLUSH/TCIOFLUSH). This prevents
unexpected stale data after a user application calls tcflush().
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Antonino Ingargiola <tritemio@gmail.com>
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pm3fb_setup() should only compiled if pm3fb is built statically in the kernel.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
