Because of some board issues, we need to disable parallel detect on
an HP blade. Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches to workaround the 5706S on an HP blade were not
sufficient. The link state still does not change properly in some
cases. This patch adds polling to make it completely reliable.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/bnx2.c:67: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking for the ASYM_PAUSE bit for 1000Base-X twice instead
checking for both the 1000Base-X bit and the 10/100/1000Base-T bit.
The purpose of the logic is to tell the firmware that ASYM_PAUSE is
set on either the Serdes or Copper interface.
Problem was discovered by Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the programmable high/low water marks in 5709 for
802.3 flow control.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CTX_WR macro is unnecessary and obfuscates the code.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REG_WR_IND/REG_RD_IND macros are unnecessary and obfuscate the
code. Many callers to these macros read and write shared memory from
the bp->shmem_base, so we add 2 similar functions that automatically
add the shared memory base.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the tx coalescing setup code independent of the MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Correct the MII expansion serdes control register definition.
2. Check an additional RUDI_INVALID bit when determining 5706S link.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix "bp->phy_flags" names with BNX2_PHY_FLAG_* for consistency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some blade systems using the 5706 serdes, the hardware sometimes
does not properly generate link down interrupts. We add a workaround
in the driver's timer to force a link-down when some PHY registers
report loss of SYNC.
The parallel detect logic is cleaned up slightly to better integrate
the workaround.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more correct to get the status block from the bnx2_napi struct
instead of the bnx2 struct. It happens that they are the same in this
case because we are using the first MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip has problem running in this mode and needs to be disabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_init_napi() to void.
Warning was noted by DaveM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable new tx ring and add new MSIX handler and NAPI poll function
for the new tx ring. Enable MSIX when the hardware supports it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To separate TX IRQs into a different MSIX vector, we need to
support a new tx ring. The original tx ring will still be used
when not using MSIX.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_napi struct into an array and add code to manage multiple
IRQs. MSIX hardware structures and new registers are also added.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bnx2_napi structure that will hold a napi_struct and
other fields to handle NAPI polling for the napi_struct. Various tx
and rx indexes and status block pointers will be moved from the main
bnx2 structure to this bnx2_napi structure.
Most NAPI path functions are modified to be passed this bnx2_napi
struct pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a table to keep track of multiple IRQs and restructure the IRQ
request and free functions so that they can be easily expanded to
handle multiple IRQs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code cleaner and easier to support different tx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MTU requires more than 1 page for the SKB, enable the page ring
and calculate the size of the page ring. This will guarantee order-0
allocation regardless of the MTU size.
Fixup loopback test packet size so that we don't deal with the pages
during loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to reuse a page in case of allocation or other errors.
Add code to construct the completed SKB with the additional data in
the pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields to keep track of the pages and the page rings.
Add functions to allocate and free pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the common functions that will be used to initialize the
normal RX rings and the page rings.
Change the copybreak constant RX_COPY_THRESH to 128. This same
constant will be used for the max. size of the linear SKB when pages
are used. Copybreak will be turned off when pages are used.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function to handle new SKB allocation and to prepare the
completed SKB. This makes it easier to add support for non-linear
SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the various ring constants to make the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets can be left in the RX ring if the NAPI budget is reached.
This is caused by storing the latest rx index at the beginning of
bnx2_rx_int(). We may not process all the work up to this index
if the budget is reached and so some packets in the RX ring may rot
when we later check for more work using this stored rx index.
The fix is to not store this latest hw index and only store the
processed rx index. We use a new function bnx2_get_hw_rx_cons()
to fetch the latest hw rx index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (51 commits)
[IPV6]: Fix again the fl6_sock_lookup() fixed locking
[NETFILTER]: nf_conntrack_tcp: fix connection reopening fix
[IPV6]: Fix race in ipv6_flowlabel_opt() when inserting two labels
[IPV6]: Lost locking in fl6_sock_lookup
[IPV6]: Lost locking when inserting a flowlabel in ipv6_fl_list
[NETFILTER]: xt_sctp: fix mistake to pass a pointer where array is required
[NET]: Fix OOPS due to missing check in dev_parse_header().
[TCP]: Remove lost_retrans zero seqno special cases
[NET]: fix carrier-on bug?
[NET]: Fix uninitialised variable in ip_frag_reasm()
[IPSEC]: Rename mode to outer_mode and add inner_mode
[IPSEC]: Disallow combinations of RO and AH/ESP/IPCOMP
[IPSEC]: Use the top IPv4 route's peer instead of the bottom
[IPSEC]: Store afinfo pointer in xfrm_mode
[IPSEC]: Add missing BEET checks
[IPSEC]: Move type and mode map into xfrm_state.c
[IPSEC]: Fix length check in xfrm_parse_spi
[IPSEC]: Move ip_summed zapping out of xfrm6_rcv_spi
[IPSEC]: Get nexthdr from caller in xfrm6_rcv_spi
[IPSEC]: Move tunnel parsing for IPv4 out of xfrm4_input
...
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bug is in the code in bnx2_set_power_state() that assumes copper
devices when setting up WoL. This is no longer true after adding WoL
support for Serdes devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to read and store sblk->status_idx before checking for more work.
The status idx is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When completing bnx2_poll(), we should always break out of the while
loop and return work_done instead of returning 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default WoL setting to match the NVRAM's setting. It
always defaulted to WoL disabled before and caused a lot of confusion
for users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote PHY media type and link status can change between
->probe() and ->open(). For correct operation, we need to get the
new status again during ->open().
The ethtool link test and loopback test are also fixed to work with
remote PHY. PHY loopback is simply skipped when remote PHY is
present.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
