Two of the Ethernet switches on this board have EEPROMs connected.
Add the eeprom-length property to the device tree, making it possible
to access the EEPROM using ethtool -e.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Currently the GPIO flag is GPIO_ACTIVE_HIGH. In order to make
the dts description accurate, pass the GPIO_ACTIVE_LOW flag instead.
This change is safe because the gpio regulator driver does not take the
GPIO flag polarity into account.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Currently the GPIO flag is 0, which means active-high. In order to make
the dts description accurate, pass the GPIO_ACTIVE_LOW flag instead.
This change is safe because the gpio regulator driver does not take the
GPIO flag polarity into account.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
On imx7d-pico the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-pico has the WDOG1_B pin connected to the PMIC, so add the
wdog1 node and use the 'fsl,ext-reset-output' property to
properly describe it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most of DT files in ARM use #include "..." to make pre-processor
include DT in the same directory, but we have some exceptional files
that use #include <...> for that.
Fix them to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts path from
dtc_cpp_flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"bcrmf" is a typo and "wifi" is the preferred form to describe
such node, so change it accordingly.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
mmc1: new MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
On imx7s-warp the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
With this change HS200 error is gone and another benefit is that the
card can operate in DDR52 mode now:
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
Suggested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial support for imx7d-pico board.
Add support for eMMC, USB host, USB device, PMIC, Ethernet and audio.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PWM driver has now capability to specify the PWM polarity
which is e.g. for backlight control. Allow to make use of PWM
polarity by specifying pwm-cells to be 3 in the base dt.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
List GPR block as compatible "fsl,imx6q-iomuxc-gpr" to support drivers
requesting it that way (PCIe driver is one example).
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that support for 'anatop-enable-bit' has been added to ANADIG
driver, reintroduce 'anatop-enable-bit' for all applicable LDOs.
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx6sx-sdb rev B/C the VDD_ARM_IN and VDD_SOC_IN supplies are connected
together and both are supplied by the SW1A PMIC output, so model this
correctly in the device tree.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When running a stress playback/stop loop test on a mx6colibri channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When running a stress playback/stop loop test on a mx6wandboard channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USDHC instances need the USDHC NAND and IPG clock in order to
operate. Reference them properly by replacing the dummy clocks with
the actual clocks.
Note that both clocks are currently implicitly enabled since they
are part of the i.MX 7 clock drivers init_on list. This might
change in the future.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 compatbile string is missing the vendor part, add it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 vendor is microcrystal, not ST.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 vendor is microcrystal, not ST.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the more specific QuadPlus compatible to the GPC node, to trigger the
required workarounds in the power domain code.
In regard to the interrupt mapping the QuadPlus controller is fully
compatible to the Quad one, so keep that compatible in place.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adopt the i.MX6Q/DL DT to the new and more flexible GPC binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the sky2 ethernet device node from the pcie controller which was
invalid to begin with.
The original intent was to allow the bootloader to populate the MAC via
dt but this requires the PCI bus topology to be complete in dt as well
and as these boards have an expansion connector that topology is dynamic
and can't be represented here.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull UML fixes from Richard Weinberger:
"No new stuff, just fixes"
* 'for-linus-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Add missing NR_CPUS include
um: Fix to call read_initrd after init_bootmem
um: Include kbuild.h instead of duplicating its macros
um: Fix PTRACE_POKEUSER on x86_64
um: Set number of CPUs
um: Fix _print_addr()
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm, docs: update memory.stat description with workingset* entries
mm: vmscan: scan until it finds eligible pages
mm, thp: copying user pages must schedule on collapse
dax: fix PMD data corruption when fault races with write
dax: fix data corruption when fault races with write
ext4: return to starting transaction in ext4_dax_huge_fault()
mm: fix data corruption due to stale mmap reads
dax: prevent invalidation of mapped DAX entries
Tigran has moved
mm, vmalloc: fix vmalloc users tracking properly
mm/khugepaged: add missed tracepoint for collapse_huge_page_swapin
gcov: support GCC 7.1
mm, vmstat: Remove spurious WARN() during zoneinfo print
time: delete current_fs_time()
hwpoison, memcg: forcibly uncharge LRU pages
Pull libnvdimm fixes from Dan Williams:
"Incremental fixes and a small feature addition on top of the main
libnvdimm 4.12 pull request:
- Geert noticed that tinyconfig was bloated by BLOCK selecting DAX.
The size regression is fixed by moving all dax helpers into the
dax-core and only specifying "select DAX" for FS_DAX and
dax-capable drivers. He also asked for clarification of the
NR_DEV_DAX config option which, on closer look, does not need to be
a config option at all. Mike also throws in a DEV_DAX_PMEM fixup
for good measure.
- Ben's attention to detail on -stable patch submissions caught a
case where the recent fixes to arch_copy_from_iter_pmem() missed a
condition where we strand dirty data in the cache. This is tagged
for -stable and will also be included in the rework of the pmem api
to a proposed {memcpy,copy_user}_flushcache() interface for 4.13.
- Vishal adds a feature that missed the initial pull due to pending
review feedback. It allows the kernel to clear media errors when
initializing a BTT (atomic sector update driver) instance on a pmem
namespace.
- Ross noticed that the dax_device + dax_operations conversion broke
__dax_zero_page_range(). The nvdimm unit tests fail to check this
path, but xfstests immediately trips over it. No excuse for missing
this before submitting the 4.12 pull request.
These all pass the nvdimm unit tests and an xfstests spot check. The
set has received a build success notification from the kbuild robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
filesystem-dax: fix broken __dax_zero_page_range() conversion
libnvdimm, btt: ensure that initializing metadata clears poison
libnvdimm: add an atomic vs process context flag to rw_bytes
x86, pmem: Fix cache flushing for iovec write < 8 bytes
device-dax: kill NR_DEV_DAX
block, dax: move "select DAX" from BLOCK to FS_DAX
device-dax: Tell kbuild DEV_DAX_PMEM depends on DEV_DAX
Pull perf updates/fixes from Ingo Molnar:
"Mostly tooling updates, but also two kernel fixes: a call chain
handling robustness fix and an x86 PMU driver event definition fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/callchain: Force USER_DS when invoking perf_callchain_user()
tools build: Fixup sched_getcpu feature test
perf tests kmod-path: Don't fail if compressed modules aren't supported
perf annotate: Fix AArch64 comment char
perf tools: Fix spelling mistakes
perf/x86: Fix Broadwell-EP DRAM RAPL events
perf config: Refactor a duplicated code for obtaining config file name
perf symbols: Allow user probes on versioned symbols
perf symbols: Accept symbols starting at address 0
tools lib string: Adopt prefixcmp() from perf and subcmd
perf units: Move parse_tag_value() to units.[ch]
perf ui gtk: Move gtk .so name to the only place where it is used
perf tools: Move HAS_BOOL define to where perl headers are used
perf memswap: Split the byteswap memory range wrappers from util.[ch]
perf tools: Move event prototypes from util.h to event.h
perf buildid: Move prototypes from util.h to build-id.h
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- two boot crash fixes
- unwinder fixes
- kexec related kernel direct mappings enhancements/fixes
- more Clang support quirks
- minor cleanups
- Documentation fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel_rdt: Fix a typo in Documentation
x86/build: Don't add -maccumulate-outgoing-args w/o compiler support
x86/boot/32: Fix UP boot on Quark and possibly other platforms
x86/mm/32: Set the '__vmalloc_start_set' flag in initmem_init()
x86/kexec/64: Use gbpages for identity mappings if available
x86/mm: Add support for gbpages to kernel_ident_mapping_init()
x86/boot: Declare error() as noreturn
x86/mm/kaslr: Use the _ASM_MUL macro for multiplication to work around Clang incompatibility
x86/mm: Fix boot crash caused by incorrect loop count calculation in sync_global_pgds()
x86/asm: Don't use RBP as a temporary register in csum_partial_copy_generic()
x86/microcode/AMD: Remove redundant NULL check on mc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJZFWTzAAoJELDendYovxMv24cIAJ3U2OZ64d7WTKD37AT2O6nF
6R3j+zJ6apoKX4zHvhWUOHZ6jpTASTnaisiIskVc52JcgAK0f8ZYTg5nhyWPceAD
Icf+JuXrI6uplD97qsjt7X9FbxUsRZninfsznoBkK6P8Cw8ZWlWIWIl6e3CrVwBD
geyKcbsKkVG8+bMjWvmQd94CFq5r8Ivup0sCECumx0lqw3RhxdhQvUix9eBULEoG
h/XAuPbMupdjU6phgqG4rvUjWd/R+9mIIDG1oY9Kpx4Kpn/7bHtoYZ//Qzs8bmuP
5ORujOedshdyAZqLGxQuQzo+/4E9gX3qVbaS6fPf1Ab+ra0k/iWtetUITZ0v2AQ=
=gWpG
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.12b-rc0c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains two fixes for booting under Xen introduced during this
merge window and two fixes for older problems, where one is just much
more probable due to another merge window change"
* tag 'for-linus-4.12b-rc0c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: adjust early dom0 p2m handling to xen hypervisor behavior
x86/amd: don't set X86_BUG_SYSRET_SS_ATTRS when running under Xen
xen/x86: Do not call xen_init_time_ops() until shared_info is initialized
x86/xen: fix xsave capability setting
Highlights include:
- rework the Linux page table geometry to lower memory usage on 64-bit Book3S
(IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features on future
firmwares.
- Freescale updates from Scott: "Includes a fix for a powerpc/next mm regression
on 64e, a fix for a kernel hang on 64e when using a debugger inside a
relocated kernel, a qman fix, and misc qe improvements."
Thanks to:
Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong, Nicholas Piggin, Roy
Pledge, Scott Wood, Valentin Longchamp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YOQs
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
- Silence module allocation failures when CONFIG_ARM*_MODULE_PLTS is
enabled. This requires a check for __GFP_NOWARN in alloc_vmap_area()
- Improve/sanitise user tagged pointers handling in the kernel
- Inline asm fixes/cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WZ6G
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
- Silence module allocation failures when CONFIG_ARM*_MODULE_PLTS is
enabled. This requires a check for __GFP_NOWARN in alloc_vmap_area()
- Improve/sanitise user tagged pointers handling in the kernel
- Inline asm fixes/cleanups
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Silence first allocation with CONFIG_ARM64_MODULE_PLTS=y
ARM: Silence first allocation with CONFIG_ARM_MODULE_PLTS=y
mm: Silence vmap() allocation failures based on caller gfp_flags
arm64: uaccess: suppress spurious clang warning
arm64: atomic_lse: match asm register sizes
arm64: armv8_deprecated: ensure extension of addr
arm64: uaccess: ensure extension of access_ok() addr
arm64: ensure extension of smp_store_release value
arm64: xchg: hazard against entire exchange variable
arm64: documentation: document tagged pointer stack constraints
arm64: entry: improve data abort handling of tagged pointers
arm64: hw_breakpoint: fix watchpoint matching for tagged pointers
arm64: traps: fix userspace cache maintenance emulation on a tagged pointer
NAND, from Boris:
"""
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
SPI NOR, from Cyrille:
"""
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
And a few fixes for Gemini and Versatile platforms on physmap-of
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dxj5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
When booted as pv-guest the p2m list presented by the Xen is already
mapped to virtual addresses. In dom0 case the hypervisor might make use
of 2M- or 1G-pages for this mapping. Unfortunately while being properly
aligned in virtual and machine address space, those pages might not be
aligned properly in guest physical address space.
So when trying to obtain the guest physical address of such a page
pud_pfn() and pmd_pfn() must be avoided as those will mask away guest
physical address bits not being zero in this special case.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
When running as Xen pv guest X86_BUG_SYSRET_SS_ATTRS must not be set
on AMD cpus.
This bug/feature bit is kind of special as it will be used very early
when switching threads. Setting the bit and clearing it a little bit
later leaves a critical window where things can go wrong. This time
window has enlarged a little bit by using setup_clear_cpu_cap() instead
of the hypervisor's set_cpu_features callback. It seems this larger
window now makes it rather easy to hit the problem.
The proper solution is to never set the bit in case of Xen.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Juergen Gross <jgross@suse.com>
When CONFIG_ARM64_MODULE_PLTS is enabled, the first allocation using the
module space fails, because the module is too big, and then the module
allocation is attempted from vmalloc space. Silence the first allocation
failure in that case by setting __GFP_NOWARN.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When CONFIG_ARM_MODULE_PLTS is enabled, the first allocation using the
module space fails, because the module is too big, and then the module
allocation is attempted from vmalloc space. Silence the first allocation
failure in that case by setting __GFP_NOWARN.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As of commits d8f347ba35cf ("nios2: enable earlycon support"),
0dcc0542a006 ("serial: altera_jtaguart: add earlycon support") and
4d9d7d896d77 ("serial: altera_uart: add earlycon support"), the nios2
architecture and the altera_uart/altera_jtaguart drivers support
earlycon. Thus, the custom early console implementation for nios2 is no
longer necessary to get early boot messages. Remove it and rely fully on
earlycon support.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Improvement of headers_install by Nicolas Dichtel.
It has been long since the introduction of uapi directories,
but the de-coupling of exported headers has not been completed.
Headers listed in header-y are exported whether they exist in
uapi directories or not. His work fixes this inconsistency.
All (and only) headers under uapi directories are now exported.
The asm-generic wrappers are still exceptions, but this is a big
step forward.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rqdo
-----END PGP SIGNATURE-----
Merge tag 'kbuild-uapi-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild UAPI updates from Masahiro Yamada:
"Improvement of headers_install by Nicolas Dichtel.
It has been long since the introduction of uapi directories, but the
de-coupling of exported headers has not been completed. Headers listed
in header-y are exported whether they exist in uapi directories or
not. His work fixes this inconsistency.
All (and only) headers under uapi directories are now exported. The
asm-generic wrappers are still exceptions, but this is a big step
forward"
* tag 'kbuild-uapi-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
arch/include: remove empty Kbuild files
uapi: export all arch specifics directories
uapi: export all headers under uapi directories
smc_diag.h: fix include from userland
btrfs_tree.h: fix include from userland
uapi: includes linux/types.h before exporting files
Makefile.headersinst: remove destination-y option
Makefile.headersinst: cleanup input files
x86: stop exporting msr-index.h to userland
nios2: put setup.h in uapi
h8300: put bitsperlong.h in uapi
- Clean up builddeb script
- Use full path for KBUILD_IMAGE to fix rpm-pkg build
- Fix objdiff tool to ignore debug info
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vptn
-----END PGP SIGNATURE-----
Merge tag 'kbuild-misc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull misc Kbuild updates from Masahiro Yamada:
- clean up builddeb script
- use full path for KBUILD_IMAGE to fix rpm-pkg build
- fix objdiff tool to ignore debug info
* tag 'kbuild-misc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
builddeb: fix typo
builddeb: Update a few outdated and hardcoded strings
deb-pkg: Remove the KBUILD_IMAGE workaround
unicore32: Use full path in KBUILD_IMAGE definition
sh: Use full path in KBUILD_IMAGE definition
arc: Use full path in KBUILD_IMAGE definition
arm: Use full path in KBUILD_IMAGE definition
arm64: Use full path in KBUILD_IMAGE definition
scripts: objdiff: Ignore debug info when comparing
- Improve Clang support
- Clean up various Makefiles
- Improve build log visibility (objtool, alpha, ia64)
- Improve compiler flag evaluation for better build performance
- Fix GCC version-dependent warning
- Fix genksyms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nka/
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- improve Clang support
- clean up various Makefiles
- improve build log visibility (objtool, alpha, ia64)
- improve compiler flag evaluation for better build performance
- fix GCC version-dependent warning
- fix genksyms
* tag 'kbuild-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (23 commits)
kbuild: dtbinst: remove unnecessary __dtbs_install_prep target
ia64: beatify build log for gate.so and gate-syms.o
alpha: make short build log available for division routines
alpha: merge build rules of division routines
alpha: add $(src)/ rather than $(obj)/ to make source file path
Makefile: evaluate LDFLAGS_BUILD_ID only once
objtool: make it visible in make V=1 output
kbuild: clang: add -no-integrated-as to KBUILD_[AC]FLAGS
kbuild: Add support to generate LLVM assembly files
kbuild: Add better clang cross build support
kbuild: drop -Wno-unknown-warning-option from clang options
kbuild: fix asm-offset generation to work with clang
kbuild: consolidate redundant sed script ASM offset generation
frv: Use OFFSET macro in DEF_*REG()
kbuild: avoid conflict between -ffunction-sections and -pg on gcc-4.7
kbuild: Consolidate header generation from ASM offset information
kbuild: use -Oz instead of -Os when using clang
kbuild, LLVMLinux: Add -Werror to cc-option to support clang
Kbuild: make designated_init attribute fatal
kbuild: drop unneeded patterns '.*.orig' and '.*.rej' from distclean
...
Subsystem:
- Add OF device ID table for i2c drivers
New driver:
- Motorola CPCAP PMIC RTC
Drivers:
- cmos: fix IRQ selection
- ds1307: Add ST m41t0 support
- ds1374: fix watchdog configuration
- sh: Add rza series support
-----BEGIN PGP SIGNATURE-----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=40TA
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC subsystem update:
- Add OF device ID table for i2c drivers
New RTC driver:
- Motorola CPCAP PMIC RTC
RTC driver updates:
- cmos: fix IRQ selection
- ds1307: Add ST m41t0 support
- ds1374: fix watchdog configuration
- sh: Add rza series support"
* tag 'rtc-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (33 commits)
rtc: gemini: add return value validation
rtc: snvs: fix an incorrect check of return value
rtc: ds1374: wdt: Fix stop/start ioctl always returning -EINVAL
rtc: ds1374: wdt: Fix issue with timeout scaling from secs to wdt ticks
rtc: sh: mark PM functions as unused
rtc: hid-sensor-time: remove some dead code
rtc: m41t80: Add proper compatible for rv4162
rtc: ds1307: Add m41t0 to OF device ID table
rtc: ds1307: support m41t0 variant
rtc: cpcap: fix improper use of IRQ_NONE for request_threaded_irq
rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs
x86: i8259: export legacy_pic symbol
dt-bindings: rtc: document the rtc-sh bindings
rtc: sh: add support for rza series
rtc: cpcap: kfreeing devm allocated memory
rtc: wm8350: Remove unused to_wm8350_from_rtc_dev
rtc: cpcap: new rtc driver
dt-bindings: Add vendor prefix for Motorola
rtc: omap: mark PM methods as __maybe_unused
rtc: omap: remove incorrect __exit markups
...
