Using previously added infrastructure we can now extract a device's JEDEC
ID, compare it to a list of known and supported devices and make assumptions
based on known characteristics of a given chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Supply a lookup table of all the devices we intend to support. This table
is used to store device information such as; a human readable device name,
their JEDEC ID (plus the extended version), sector size and amount, a bit
store of a device's capabilities, its maximum running frequency and
possible use of a per-device configuration call-back.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
JEDEC have helped to standardise a great deal of the commands which
can be issued to a Serial Flash devices. Many of the Serial Flash
Discoverable Parameters (SFDP) commands are generic across devices.
This patch provides a shared point where these commands can be
defined.
Suggested-by: Mark Brown <broonie@kernel.org>
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Once we start supporting devices it will be handy go detect them
dynamically. This will be done using the chip's unique JEDEC ID. This
patch allows us to extract a device's JEDEC ID using the a predefined
FSM register write sequence.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When invoked the driver will attempt to read any available data from
the FSM's data register. Any data collected from this FIFO would have
originated from the flash chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM hardware works by setting a predetermined sequence of register
writes. Rather than open coding them inside each functional block we're
going to define them in a series of formatted 'sequence structures'.
This patch provides the framework which shall be used for every action.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch uses default values to initialise a connected flash chip. This
includes; a device soft reset, setting of a safe working frequency, a
switch into Fast Sequencing Mode, configuring of timing data and a purge
of the FIFO.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Here we provide the FSM's register addresses, register bit names/offsets
and some commands which will prove useful as we start bulk the FMS's
driver out with functionality.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is a new driver. It's used to communicate with a special type of
optimised Serial Flash Controller called the FSM. The FSM uses a subset
of the SPI protocol to communicate with supported NOR-Flash devices.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
