Add support for drivers to report the total number of MPDUs received
and the number of MPDUs received with an FCS error from a specific
peer. These counters will be incremented only when the TA of the
frame matches the MAC address of the peer irrespective of FCS
error.
It should be noted that the TA field in the frame might be corrupted
when there is an FCS error and TA matching logic would fail in such
cases. Hence, FCS error counter might not be fully accurate, but it can
provide help in detecting bad RX links in significant number of cases.
This FCS error counter without full accuracy can be used, e.g., to
trigger a kick-out of a connected client with a bad link in AP mode to
force such a client to roam to another AP.
Signed-off-by: Ankita Bajaj <bankita@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous implementation of SAE authentication in infrastructure BSS was
somewhat restricting and not exactly clean way of handling the two
auth() operations. This ended up removing and re-adding the STA entry
for the AP in the middle of authentication and also messing up
authentication state tracking through the sequence of four
Authentication frames. Furthermore, this did not work if the AP ended up
sending out SAE Confirm (auth trans #2) immediately after SAE Commit
(auth trans #1) before the station had time to transmit its SAE Confirm.
Clean up authentication state handling for the SAE case to allow two
rounds of auth() calls without dropping all state between those
operations. Track peer Confirmed status and mark authentication
completed only once both ends have confirmed.
ieee80211_mgd_auth() check for EBUSY cases is now handling only the
pending association (ifmgd->assoc_data) while all pending authentication
(ifmgd->auth_data) cases are allowed to proceed to allow user space to
start a new connection attempt from scratch even if the previously
requested authentication is still waiting completion. This is needed to
avoid making SAE error cases with retries take excessive amount of time
with no means for the user space to stop that (apart from setting the
netdev down).
As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up
to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing
SAE authentication since the new ieee80211_mark_sta_auth() helper
function can handle both completion of authentication and updates to the
STA entry under the same condition and there is no need to return from
the function between those operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to conditionally replace full allocation of
auth_data to use reallocation for the case of continuing SAE
authentication. Furthermore, there was not really any point in having
this check done so late in the function after having already completed
number of steps that cannot be used anyway in the error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication exchange can be completed in both TX and RX paths for
SAE, so move this common functionality into a helper function to avoid
having to implement practically the same operations in two places when
extending SAE implementation in the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there are few packets (e.g. for sampling attempts), the exponentially
weighted variance is usually vastly overestimated, making the resulting data
essentially useless. As far as I know, there has not been any practical use
for this, so let's not waste any cycles on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are highly unlikely to be used quickly, even if the link
deteriorates rapidly. This improves throughput in cases where CCK rates
are not reliable enough to be skipped entirely during sampling.
Sampling these rates regularly can cost a lot of airtime.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Long/short preamble selection cannot be sampled separately, since it
depends on the BSS state. Because of that, sampling attempts to
currently not used preamble modes are not counted in the statistics,
which leads to CCK rates being sampled too often.
Fix statistics accounting for long/short preamble by increasing the
index where necessary.
Fix excessive CCK rate sampling by dropping unsupported sample attempts.
This improves throughput on 2.4 GHz channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a harmless underflow issue when CCK rates are actively being used
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mi->supported[MINSTREL_CCK_GROUP] needs to be updated
short preamble rates need to be marked as supported regardless of
whether it's currently enabled. Its state can change at any time without
a rate_update call.
Fixes: 782dda00ab ("mac80211: minstrel_ht: move short preamble check out of get_rate")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By storing a shift value for all duration values of a group, we can
reduce precision by a neglegible amount to make it fit into a u16 value.
This improves cache footprint and reduces size:
Before:
text data bss dec hex filename
10024 116 0 10140 279c rc80211_minstrel_ht.o
After:
text data bss dec hex filename
9368 116 0 9484 250c rc80211_minstrel_ht.o
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy-only devices are not very common and the overhead of the extra
code for HT and VHT rates is not big enough to justify all those extra
lines of code to make it optional.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
debugfs entries are cleaned up by debugfs_remove_recursive already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If peer support reception of STBC and LDPC, enable them for better
performance.
Signed-off-by: Chaitanya TK <chaitanya.mgit@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I'm not really sure exactly _why_ I've been carrying a note
for what's probably _years_ to check that we don't do this,
but we clearly do reflect frames back to the station itself
if it sends such.
One way or the other, it's useless since the station doesn't
really need the AP to talk to itself, so suppress it.
While at it, clarify some of the logic by removing skb->data
references in favour of the destination address (pointer) we
already have separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of open-coding a lot of calls to is_valid_ie_attr(),
add this validation directly to the policy, now that we can.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many range checks can be done in the policy, move them
there. A few in mesh are added in the code (taken out of
the macros) because they don't fit into the s16 range in
the policy validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using skcipher just makes the code longer, and mac80211
also "open-codes" the WEP encrypt/decrypt.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next, which pulled in net, so I can merge a few more
patches that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix 5 warnings and 14 checks issued by checkpatch.pl:
CHECK: Logical continuations should be on the previous line
+ if ((q->vars.qdelay < q->params.target / 2)
+ && (q->vars.prob < MAX_PROB / 5))
WARNING: line over 80 characters
+ q->params.tupdate = usecs_to_jiffies(nla_get_u32(tb[TCA_PIE_TUPDATE]));
CHECK: Blank lines aren't necessary after an open brace '{'
+{
+
CHECK: braces {} should be used on all arms of this statement
+ if (qlen < QUEUE_THRESHOLD)
[...]
+ else {
[...]
CHECK: Unbalanced braces around else statement
+ else {
CHECK: No space is necessary after a cast
+ if (delta > (s32) (MAX_PROB / (100 / 2)) &&
CHECK: Unnecessary parentheses around 'qdelay == 0'
+ if ((qdelay == 0) && (qdelay_old == 0) && update_prob)
CHECK: Unnecessary parentheses around 'qdelay_old == 0'
+ if ((qdelay == 0) && (qdelay_old == 0) && update_prob)
CHECK: Unnecessary parentheses around 'q->vars.prob == 0'
+ if ((q->vars.qdelay < q->params.target / 2) &&
+ (q->vars.qdelay_old < q->params.target / 2) &&
+ (q->vars.prob == 0) &&
+ (q->vars.avg_dq_rate > 0))
CHECK: Unnecessary parentheses around 'q->vars.avg_dq_rate > 0'
+ if ((q->vars.qdelay < q->params.target / 2) &&
+ (q->vars.qdelay_old < q->params.target / 2) &&
+ (q->vars.prob == 0) &&
+ (q->vars.avg_dq_rate > 0))
CHECK: Blank lines aren't necessary before a close brace '}'
+
+}
CHECK: Comparison to NULL could be written "!opts"
+ if (opts == NULL)
CHECK: No space is necessary after a cast
+ ((u32) PSCHED_TICKS2NS(q->params.target)) /
WARNING: line over 80 characters
+ nla_put_u32(skb, TCA_PIE_TUPDATE, jiffies_to_usecs(q->params.tupdate)) ||
CHECK: Blank lines aren't necessary before a close brace '}'
+
+}
CHECK: No space is necessary after a cast
+ .delay = ((u32) PSCHED_TICKS2NS(q->vars.qdelay)) /
WARNING: Missing a blank line after declarations
+ struct sk_buff *skb;
+ skb = qdisc_dequeue_head(sch);
WARNING: Missing a blank line after declarations
+ struct pie_sched_data *q = qdisc_priv(sch);
+ qdisc_reset_queue(sch);
WARNING: Missing a blank line after declarations
+ struct pie_sched_data *q = qdisc_priv(sch);
+ q->params.tupdate = 0;
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM commands and response handling. It also defines OEM
command and response structure as per NCSI specification along with its
handlers.
ncsi_cmd_handler_oem: This is a generic command request handler for OEM
commands
ncsi_rsp_handler_oem: This is a generic response handler for OEM commands
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move_addr_to_kernel() returns only negative values on error, or zero on
success. Rewrite the error check to an idiomatic form to avoid confusing
the reader.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of TC attributes are processed without proper validation
(e.g., length checks). Add a tca policy for all input attributes and use
when invoking nlmsg_parse.
The 2 Fixes tags below cover the latest additions. The other attributes
are a string (KIND), nested attribute (OPTIONS which does seem to have
validation in most cases), for dumps only or a flag.
Fixes: 5bc1701881 ("net: sched: introduce multichain support for filters")
Fixes: d47a6b0e7c ("net: sched: introduce ingress/egress block index attributes for qdisc")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, rtnl_fdb_dump() assumes the family header is 'struct ifinfomsg',
which is not always true -- 'struct ndmsg' is used by iproute2 ('ip neigh').
The problem is, the function bails out early if nlmsg_parse() fails, which
does occur for iproute2 usage of 'struct ndmsg' because the payload length
is shorter than the family header alone (as 'struct ifinfomsg' is assumed).
This breaks backward compatibility with userspace -- nothing is sent back.
Some examples with iproute2 and netlink library for go [1]:
1) $ bridge fdb show
33:33:00:00:00:01 dev ens3 self permanent
01:00:5e:00:00:01 dev ens3 self permanent
33:33:ff:15:98:30 dev ens3 self permanent
This one works, as it uses 'struct ifinfomsg'.
fdb_show() @ iproute2/bridge/fdb.c
"""
.n.nlmsg_len = NLMSG_LENGTH(sizeof(struct ifinfomsg)),
...
if (rtnl_dump_request(&rth, RTM_GETNEIGH, [...]
"""
2) $ ip --family bridge neigh
RTNETLINK answers: Invalid argument
Dump terminated
This one fails, as it uses 'struct ndmsg'.
do_show_or_flush() @ iproute2/ip/ipneigh.c
"""
.n.nlmsg_type = RTM_GETNEIGH,
.n.nlmsg_len = NLMSG_LENGTH(sizeof(struct ndmsg)),
"""
3) $ ./neighlist
< no output >
This one fails, as it uses 'struct ndmsg'-based.
neighList() @ netlink/neigh_linux.go
"""
req := h.newNetlinkRequest(unix.RTM_GETNEIGH, [...]
msg := Ndmsg{
"""
The actual breakage was introduced by commit 0ff50e83b5 ("net: rtnetlink:
bail out from rtnl_fdb_dump() on parse error"), because nlmsg_parse() fails
if the payload length (with the _actual_ family header) is less than the
family header length alone (which is assumed, in parameter 'hdrlen').
This is true in the examples above with struct ndmsg, with size and payload
length shorter than struct ifinfomsg.
However, that commit just intends to fix something under the assumption the
family header is indeed an 'struct ifinfomsg' - by preventing access to the
payload as such (via 'ifm' pointer) if the payload length is not sufficient
to actually contain it.
The assumption was introduced by commit 5e6d243587 ("bridge: netlink dump
interface at par with brctl"), to support iproute2's 'bridge fdb' command
(not 'ip neigh') which indeed uses 'struct ifinfomsg', thus is not broken.
So, in order to unbreak the 'struct ndmsg' family headers and still allow
'struct ifinfomsg' to continue to work, check for the known message sizes
used with 'struct ndmsg' in iproute2 (with zero or one attribute which is
not used in this function anyway) then do not parse the data as ifinfomsg.
Same examples with this patch applied (or revert/before the original fix):
$ bridge fdb show
33:33:00:00:00:01 dev ens3 self permanent
01:00:5e:00:00:01 dev ens3 self permanent
33:33:ff:15:98:30 dev ens3 self permanent
$ ip --family bridge neigh
dev ens3 lladdr 33:33:00:00:00:01 PERMANENT
dev ens3 lladdr 01:00:5e:00:00:01 PERMANENT
dev ens3 lladdr 33:33:ff:15:98:30 PERMANENT
$ ./neighlist
netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x33, 0x33, 0x0, 0x0, 0x0, 0x1}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}
netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x1, 0x0, 0x5e, 0x0, 0x0, 0x1}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}
netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x33, 0x33, 0xff, 0x15, 0x98, 0x30}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}
Tested on mainline (v4.19-rc6) and net-next (3bd09b05b0).
References:
[1] netlink library for go (test-case)
https://github.com/vishvananda/netlink
$ cat ~/go/src/neighlist/main.go
package main
import ("fmt"; "syscall"; "github.com/vishvananda/netlink")
func main() {
neighs, _ := netlink.NeighList(0, syscall.AF_BRIDGE)
for _, neigh := range neighs { fmt.Printf("%#v\n", neigh) }
}
$ export GOPATH=~/go
$ go get github.com/vishvananda/netlink
$ go build neighlist
$ ~/go/src/neighlist/neighlist
Thanks to David Ahern for suggestions to improve this patch.
Fixes: 0ff50e83b5 ("net: rtnetlink: bail out from rtnl_fdb_dump() on parse error")
Fixes: 5e6d243587 ("bridge: netlink dump interface at par with brctl")
Reported-by: Aidan Obley <aobley@pivotal.io>
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case ip_fib_metrics_init() returns an error, we better
rewrite rt->fib6_metrics with &dst_default_metrics so that
we do not crash later in ip_fib_metrics_put()
Fixes: 767a221753 ("net: common metrics init helper for FIB entries")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the socket lookup cost in udp_gro_receive if no socket has a
udp tunnel callback configured.
udp_sk(sk)->gro_receive requires a registration with
setup_udp_tunnel_sock, which enables the static key.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following Sparse warnings:
net/bpfilter/bpfilter_kern.c:62:21: warning: cast removes address space
of expression
net/bpfilter/bpfilter_kern.c:101:49: warning: Using plain integer as
NULL pointer
Signed-off-by: Shanthosh RK <shanthosh.rk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit ec3ed293e7 ("net_sched: change tcf_del_walker() to take idrinfo->lock")
we move fl_hw_destroy_tmplt() to a workqueue to avoid blocking
with the spinlock held. Unfortunately, this causes a lot of
troubles here:
1. tcf_chain_destroy() could be called right after we queue the work
but before the work runs. This is a use-after-free.
2. The chain refcnt is already 0, we can't even just hold it again.
We can check refcnt==1 but it is ugly.
3. The chain with refcnt 0 is still visible in its block, which means
it could be still found and used!
4. The block has a refcnt too, we can't hold it without introducing a
proper API either.
We can make it working but the end result is ugly. Instead of wasting
time on reviewing it, let's just convert the troubling spinlock to
a mutex, which allows us to use non-atomic allocations too.
Fixes: ec3ed293e7 ("net_sched: change tcf_del_walker() to take idrinfo->lock")
Reported-by: Ido Schimmel <idosch@idosch.org>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the attribute parsing from neigh_dump_table to neigh_dump_info, and
pass the filter arguments down to neigh_dump_table in a new struct. Add
the filter option to proxy neigh dumps as well to make them consistent.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we use raw socket as the vhost backend, a packet from virito with
gso offloading information, cannot be sent out in later validaton at
xmit path, as we did not set correct skb->protocol which is further used
for looking up the gso function.
To fix this, we set this field according to virito hdr information.
Fixes: e858fae2b0 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Jianfeng Tan <jianfeng.tan@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
for ipv4 and ipv6 to a common helper.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4 and ipv6 both use refcounted metrics if FIB entries have metrics set.
Move the common initialization code to a helper and use for both protocols.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
with a fib entry to a helper and use it in both ipv4 and ipv6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate initialization of ipv4 and ipv6 metrics when fib entries
are created into a single helper, ip_fib_metrics_init, that handles
the call to ip_metrics_convert.
If no metrics are defined for the fib entry, then the metrics is set
to dst_default_metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load the respective NAT helper module if the flow uses it.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This traffic scheduler allows traffic classes states (transmission
allowed/not allowed, in the simplest case) to be scheduled, according
to a pre-generated time sequence. This is the basis of the IEEE
802.1Qbv specification.
Example configuration:
tc qdisc replace dev enp3s0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
base-time 1528743495910289987 \
sched-entry S 01 300000 \
sched-entry S 02 300000 \
sched-entry S 04 300000 \
clockid CLOCK_TAI
The configuration format is similar to mqprio. The main difference is
the presence of a schedule, built by multiple "sched-entry"
definitions, each entry has the following format:
sched-entry <CMD> <GATE MASK> <INTERVAL>
The only supported <CMD> is "S", which means "SetGateStates",
following the IEEE 802.1Qbv-2015 definition (Table 8-6). <GATE MASK>
is a bitmask where each bit is a associated with a traffic class, so
bit 0 (the least significant bit) being "on" means that traffic class
0 is "active" for that schedule entry. <INTERVAL> is a time duration
in nanoseconds that specifies for how long that state defined by <CMD>
and <GATE MASK> should be held before moving to the next entry.
This schedule is circular, that is, after the last entry is executed
it starts from the first one, indefinitely.
The other parameters can be defined as follows:
- base-time: specifies the instant when the schedule starts, if
'base-time' is a time in the past, the schedule will start at
base-time + (N * cycle-time)
where N is the smallest integer so the resulting time is greater
than "now", and "cycle-time" is the sum of all the intervals of the
entries in the schedule;
- clockid: specifies the reference clock to be used;
The parameters should be similar to what the IEEE 802.1Q family of
specification defines.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
msix_vec_per_pf_min - This param sets the number of minimal MSIX
vectors required for the device initialization. This value is set
in the device which limits MSIX vectors per PF.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
msix_vec_per_pf_max - This param sets the number of MSIX vectors
that the device requests from the host on driver initialization.
This value is set in the device which is applicable per PF.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ignore_ari - Device ignores ARI(Alternate Routing ID) capability,
even when platforms has the support and creates same number of
partitions when platform does not support ARI capability.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix use-after-free in regulatory code
* fix rx-mgmt key flag in AP mode (mac80211)
* fix wireless extensions compat code memory leak
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAlu2bEUACgkQB8qZga/f
l8RAgw/7BfRpm3Kr7XW919naGkt/pQeJxUcuF9YggBpTCrp/DSLQYsjOBE5DyS/m
728oPD8jEDehUHasWKsbG7wit1S7ImExCHTPim8C1mbABhbqdhwD4ceUvBO7RYi2
p0+yN8X8z5D0qruMrNwhtxdE8iV9bBgmY6u1jubpJFkKLPf2euZyroH40b879CIn
aHqB42GNJCdwO2UFaPDH2cdx5DFWrDlfA1LGbrbuzrXMBfNGWYgen2JJH/5iDOyU
1rVXk/pUpVffp0Zde+66NtyCxxC0+hQwrTczEKXICb5qoWJpz6kugFGGO1oDQgdp
AbM7KNrV712h/qwTEnC1NG0KUXgocpwWIuf/cuTow0vGUJSl+O2pLS/3GLOwH2du
1u/FF4LiBc4NFXmWBPMN3LUN+Ica0/YWSbVwcv2c4guemV1EOGinlbFc+tnoue7M
fpLkQJUYCiEVFRXGWVaSl0Hr6z+zwgfa8qHYN2yq1qyB0dYHryYiVhgKLV7yisCm
RNy1hmVuV7rMsL3f4iUq/2xnL3U8qK1+19Mr+i58/kU4Tx2jMkWj0kivRdgYX4EN
XcBhJzWXrb3yMldACrCji6iRnrFMqg7osyEgFiMLMl4cZfs057+qsrJyR5xajVOi
Ws+hj3a1LukJ1nIhou4uOLAt9D7ohuJojQq6D2GLeBwfGPNkz4E=
=QyWK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-10-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three small fixes:
* fix use-after-free in regulatory code
* fix rx-mgmt key flag in AP mode (mac80211)
* fix wireless extensions compat code memory leak
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 core driver and ethernet netdev updates, please note there is a small
devlink releated update to allow extack argument to eswitch operations.
From Eli Britstein,
1) devlink: Add extack argument to the eswitch related operations
2) net/mlx5e: E-Switch, return extack messages for failures in the e-switch devlink callbacks
3) net/mlx5e: Add extack messages for TC offload failures
From Eran Ben Elisha,
4) mlx5e: Add counter for aRFS rule insertion failures
From Feras Daoud
5) Fast teardown support for mlx5 device
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the FW pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbtU45AAoJEEg/ir3gV/o+/C4H/RHA4KImrb476EdB3VNYMqAN
dgXb+bmh6sZP+jHWqQ4c3aVeh6/T8qm4gwiSn2nVTtHEnxtCdIYljzDC1Nswczeg
pSjD1eOP7M1LpAOmBb8xdnJcX7yM7r1bTklnp2sN853WShbsDRYgZBHsBwTzx25U
ZdzL4QTLuohlG/aLrbGXMntIy45ya2fVQrnK54s18nFlgsdFjEs0mi0xaUKNBC6+
P8CTohHAxuuxmL5b+6MIYLZCdgd8cLNQFdtqbckEVw7SvcRTxfraRlyqJ0YOgTGB
TdSWnqZz2JYH29wSFbpFG8qX6GCv8FoiZ+fKzldbolHk442rrktHv3+Y7qQuZVs=
=NVks
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-10-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-10-03
mlx5 core driver and ethernet netdev updates, please note there is a small
devlink releated update to allow extack argument to eswitch operations.
From Eli Britstein,
1) devlink: Add extack argument to the eswitch related operations
2) net/mlx5e: E-Switch, return extack messages for failures in the e-switch devlink callbacks
3) net/mlx5e: Add extack messages for TC offload failures
From Eran Ben Elisha,
4) mlx5e: Add counter for aRFS rule insertion failures
From Feras Daoud
5) Fast teardown support for mlx5 device
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the FW pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=b6yx
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-next-20181004' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Development
Here are some development patches for AF_RXRPC. The most significant points
are:
(1) Change the tracepoint that indicates a packet has been transmitted
into one that indicates a packet is about to be transmitted. Without
this, the response tracepoint may occur first if the round trip is
fast enough.
(2) Sort out AFS address list handling to better enforce maximum capacity
to use helper functions to fill them and to do an insertion sort to
order them. This is here to make (3) easier.
(3) Keep AF_INET addresses as AF_INET addresses rather than converting
them to AF_INET6 in both AF_RXRPC and kAFS. I hadn't realised that a
UDP6 socket would just call down into UDP4 if given an AF_INET
address.
(4) Allow the timestamp on the first DATA packet of a reply to be
retrieved by a kernel service. This will give the kAFS a more
accurate base from which to calculate the callback promise expiration.
(5) Allow the rxrpc protocol epoch value to be retrieved from an incoming
call. This will allow kAFS to determine if the fileserver restarted
and if two addresses apparently assigned to the same fileserver
actually are different boxes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the DNS resolver to retrieve a set of servers and their associated
addresses, ports, preference and weight ratings.
In terms of communication with userspace, "srv=1" is added to the callout
string (the '1' indicating the maximum data version supported by the
kernel) to ask the userspace side for this.
If the userspace side doesn't recognise it, it will ignore the option and
return the usual text address list.
If the userspace side does recognise it, it will return some binary data
that begins with a zero byte that would cause the string parsers to give an
error. The second byte contains the version of the data in the blob (this
may be between 1 and the version specified in the callout data). The
remainder of the payload is version-specific.
In version 1, the payload looks like (note that this is packed):
u8 Non-string marker (ie. 0)
u8 Content (0 => Server list)
u8 Version (ie. 1)
u8 Source (eg. DNS_RECORD_FROM_DNS_SRV)
u8 Status (eg. DNS_LOOKUP_GOOD)
u8 Number of servers
foreach-server {
u16 Name length (LE)
u16 Priority (as per SRV record) (LE)
u16 Weight (as per SRV record) (LE)
u16 Port (LE)
u8 Source (eg. DNS_RECORD_FROM_NSS)
u8 Status (eg. DNS_LOOKUP_GOT_NOT_FOUND)
u8 Protocol (eg. DNS_SERVER_PROTOCOL_UDP)
u8 Number of addresses
char[] Name (not NUL-terminated)
foreach-address {
u8 Family (AF_INET{,6})
union {
u8[4] ipv4_addr
u8[16] ipv6_addr
}
}
}
This can then be used to fetch a whole cell's VL-server configuration for
AFS, for example.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the epoch value to be queried on a server connection. This is in the
rxrpc header of every packet for use in routing and is derived from the
client's state. It's also not supposed to change unless the client gets
restarted.
AFS can make use of this information to deduce whether a fileserver has
been restarted because the fileserver makes client calls to the filesystem
driver's cache manager to send notifications (ie. callback breaks) about
conflicting changes from other clients. These convey the fileserver's own
epoch value back to the filesystem.
Signed-off-by: David Howells <dhowells@redhat.com>
Allow the timestamp on the sk_buff holding the first DATA packet of a reply
to be queried. This can then be used as a base for the expiry time
calculation on the callback promise duration indicated by an operation
result.
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_extract_addr_from_skb() doesn't use the argument that points to the
local endpoint, so remove the argument.
Signed-off-by: David Howells <dhowells@redhat.com>
AF_RXRPC opens an IPv6 socket through which to send and receive network
packets, both IPv6 and IPv4. It currently turns AF_INET addresses into
AF_INET-as-AF_INET6 addresses based on an assumption that this was
necessary; on further inspection of the code, however, it turns out that
the IPv6 code just farms packets aimed at AF_INET addresses out to the IPv4
code.
Fix AF_RXRPC to use AF_INET addresses directly when given them.
Fixes: 7b674e390e ("rxrpc: Fix IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Print the data Tx trace line before transmitting so that it appears before
the trace lines indicating success or failure of the transmission. This
makes the trace log less confusing.
Signed-off-by: David Howells <dhowells@redhat.com>
