Phy properties are expected to be found in the PHY OF node. However
this Micrel driver also allows them to be placed into the MAC OF node.
This is deprecated. Document it as such, and remove the example using
the deprecated method to prevent people copying it into new device
tree files.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT says:
====================
mvneta: Introduce RSS support and XPS configuration
this series is the first step add RSS support on mvneta.
It will allow associating an ethernet interface to a given CPU through
RSS by using "ethtool -X ethX weight". Indeed, currently I only enable
one entry in the RSS lookup table. Even if it is not really RSS, it
allows to get back the irq affinity feature we lost by using the
percpu interrupt.
The main change compared to the second version is the setup for the XPS
instead of using specific hack inside the driver in the forth
patch.
Th first patch make the default queue associate to each port and no
more a global variable.
The second patch really associates the RX queues with the CPUs instead
of masking the percpu interrupts for doing it. All the RX queues are
enabled and are statically associated with the CPUs by using a modulo
of the number of present CPUs. But at this stage only one RX queue
will receive the stream.
The third patch introduces a first level of RSS support through the
ethtool functions. As explained in the introduction there is only one
entry in the RSS lookup table which permits at the end to associate an
mvneta port to a CPU through the RX queues because the mapping is
static.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch each CPU is associated with its own set of TX queues.
It also setup the XPS with an initial configuration which set the
affinity matching the hardware configuration.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for the RSS related ethtool
function. Currently it only uses one entry in the indirection table which
allows associating an mvneta interface to a given CPU.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We enable the percpu interrupt for all the CPU and we just associate a
CPU to a few queue at the neta level. The mapping between the CPUs and
the queues is static. The queues are associated to the CPU module the
number of CPUs. However currently we only use on RX queue for a given
Ethernet port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the same default queue for all the port. Move it in the
port struct. It will allow have a different default queue for each port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets rid of the following compile warn:
net/mpls/mpls_iptunnel.c:40:5: warning: no previous prototype for
mpls_output [-Wmissing-prototypes]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a warn message when clip table overflows. If clip table isn't
allocated, return from cxgb4_clip_release() to avoid panic.
Disable offload if clip isn't enabled in the hardware.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already know "err" is zero so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "err = " assignment is missing here.
Fixes: 0d65fc1304 ('mlxsw: spectrum: Implement LAG port join/leave')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of epib and psdata remains a bit unclear in the driver,
as we access the same fields both as CPU-endian and through DMA
from the device.
Sparse warns about this:
ti/netcp_core.c:1147:21: warning: incorrect type in assignment (different base types)
ti/netcp_core.c:1147:21: expected unsigned int [usertype] *[assigned] epib
ti/netcp_core.c:1147:21: got restricted __le32 *<noident>
This uses __le32 types in a few places and uses __force where the code
looks fishy. The previous patch should really have produced the correct
behavior, but this second patch is needed to shut up the warnings about
it. Ideally it would be slightly rewritten to not need those casts,
but I don't dare do that without access to the hardware for proper
testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp driver produces tons of warnings when CONFIG_LPAE is enabled
on ARM:
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_tx_map_skb':
drivers/net/ethernet/ti/netcp_core.c:1084:13: warning: passing argument 1 of 'set_words' from incompatible pointer type [-Wincompatible-pointer-types]
This is the result of trying to pass a pointer to a dma_addr_t to
a function that expects a u32 pointer to copy that into a DMA descriptor.
Looking at that code in more detail to fix the warnings, I see multiple
related problems:
* The conversion functions are not endian-safe, as the DMA descriptors
are almost certainly fixed-endian, but the CPU is not.
* On 64-bit machines, passing a pointer through a u32 variable is a
bug, accessing an indirect pointer as a u32 pointer even more so.
* The handling of epib and psdata mixes native-endian and device-endian
data.
In this patch, I try to sort out the types for most accesses here,
adding le32_to_cpu/cpu_to_le32 where appropriate, and passing pointers
through two 32-bit words in the descriptor padding, to make it plausible
that the driver does the right thing if compiled for big-endian or
64-bit systems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has been sitting in the linux-zigbee[2] repository for a long
time. We updated it from time to time and made it available via our
github kernel repository. The Linux MAC802.15.4 support has improved a lot
since then. Thanks to all! So it’s finally time to upstream this driver.
The ADF7242 requires an add-on firmware for the automatic IEEE 802.15.4
operating modes. The firmware file is currently made available on the
ADF7242 wiki page here [1]
[1] http://wiki.analog.com/resources/tools-software/linux-drivers/networking-mac802154/adf7242
[2] http://sourceforge.net/p/linux-zigbee/kernel/ci/devel/tree/drivers/ieee802154/adf7242.c
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A Linux PC is connected with another device over Bluetooth PAN using a
BNEP interface.
Whenever a packet is tried to be sent over the BNEP interface, the
function "bnep_net_xmit()" in "net/bluetooth/bnep/netdev.c" is called.
This function calls "bnep_net_mc_filter()", which checks (if the
destination address is multicast) if the address is set in a certain
multicast filter (&s->mc_filter). If it is not, then it is not sent out.
This filter is only changed in two other functions, found in
net/bluetooth/bnep/core.c": in "bnep_ctrl_set_mc_filter()", which is
only called if a message of type "BNEP_FILTER_MULTI_ADDR_SET" is
received. Otherwise, it is set in "bnep_add_connection()", where it is
set to a default value which only adds the broadcast address to the
filter:
set_bit(bnep_mc_hash(dev->broadcast), (ulong *) &s->mc_filter);
To sum up, if the BNEP interface does not receive any message of type
"BNEP_FILTER_MULTI_ADDR_SET", it will not send out any messages with
multicast destination addresses except for broadcast.
However, in the BNEP specification (page 27 in
http://grouper.ieee.org/groups/802/15/Bluetooth/BNEP.pdf), it is said
that per default, all multicast addresses should not be filtered, i.e.
the BNEP interface should be able to send packets with any multicast
destination address.
It seems that the default case is wrong: the multicast filter should not
block almost all multicast addresses, but should not filter out any.
This leads to the problem that e.g. Neighbor Solicitation messages sent
with Bluetooth PAN over the BNEP interface to a multicast destination
address other than broadcast are blocked and not sent out.
Therefore, in the default case, we set the mc_filter to ~0LL to not
filter out any multicast addresses.
Signed-off-by: Danny Schweizer <danny.schweizer@proofnet.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The kfree_skb() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initializing Configuration field in H5 Config message to 0x01 gives
wrong impression that the value is used and needed. Later on the whole
field is rewritten with h5_cfg_field().
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reverts 6001d52 ("mac802154: tx: don't allow if down while
sync tx"). This has side effects with stop callback which flush the
transmit workqueue. The stop callback will wait until the workqueue is
flushed and holding the rtnl lock. That means it can happen that the stop
callback waits forever because it try to lock the rtnl mutex which is
already hold by stop callback.
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a static inline function ipv6_addr_prefix_copy which
copies a ipv6 address prefix(argument pfx) into the ipv6 address prefix.
The prefix len is given by plen as bits. This function mainly based on
ipv6_addr_prefix which copies one address prefix from address into a new
ipv6 address destination and zero all other address bits.
The difference is that ipv6_addr_prefix_copy don't get a prefix from an
ipv6 address, it sets a prefix to an ipv6 address with keeping other
address bits. The use case is for context based address compression
inside 6LoWPAN IPHC header which keeping ipv6 prefixes inside a context
table to lookup address-bits without sending them.
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Łukasz Duda <lukasz.duda@nordicsemi.no>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will introduce a 6lowpan entry into the debugfs if enabled.
Inside this 6lowpan directory we create a subdirectories of all 6lowpan
interfaces to offer a per interface debugfs support.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces register and unregister functionality for lowpan
interfaces. While register a lowpan interface there are several things
which need to be initialize by the 6lowpan subsystem. Upcoming
functionality need to register/unregister per interface components e.g.
debugfs entry.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel Version Read command is used to retrieve information
about hardware and firmware version/revision of Intel Bluetooth
controllers. This is an Intel generic command used in USB and
UART drivers.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're doing background scanning and connection attempts it's
possible we timeout trying to connect and go back to scanning again.
The timeout triggers a HCI_LE_Create_Connection_Cancel which will
trigger a Connection Complete with "Unknown Connection Identifier"
error status. Since we go back to scanning this isn't really a failure
and shouldn't be presented as such to user space through mgmt.
The exception to this is if the connection attempt was due to an
explicit request on an L2CAP socket (indicated by
params->explicit_connect being true). Since the socket will get an
error it's consistent to also notify the failure on mgmt in this case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All LE connections are now triggered through a preceding passive scan
and waiting for a connectable advertising report. This means we've got
the best possible guarantee that the device is within range and should
be able to request the controller to perform continuous scanning. This
way we minimize the risk that we miss out on any advertising packets.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.3+
Older Intel controllers need to enter manufacturing mode to perform
some vendor specific operations (patching, configuration...).
Add enter/exit manufaturing methods and refactor existing
manufacturing code.
Exit can be configured to perform a reset. Reset can be performed
either with patches activated or deactivated.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the standard HCI_CMD_TIMEOUT(1s) for HCI command instead of
HCI_INIT_TIMEOUT(10s) which is not justified in these cases.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The N_HCI ldisc does not define a flush_buffer() ldisc method, so
the check when opening the ldisc is always false.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can simplify a lot of code by making sure hdev->cur_adv_instance is
always up-to-date. This allows e.g. the removal of the
get_current_adv_instance() helper function and the special
HCI_ADV_CURRENT value. This patch also makes selecting instance 0x00
explicit in the various calls where advertising instances aren't
enabled, e.g. when HCI_ADVERTISING is set or we've just finished
enabling LE.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The logic in powered_update_hci() to initialize the advertising data &
state is a bit more complicated than it needs to be. It was previously
not doing anything if HCI_LE_ENABLED wasn't set, but this was not
obvious by quickly looking at the code. Now the conditions for the
various actions are more explicit. Another simplification is due to
the fact that __hci_req_schedule_adv_instance() takes care of setting
hdev->cur_adv_instance so there's no need to set it before calling the
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_req_run() function already checks for empty cmd_q and bails
out if necessary. Also, req.cmd_q should really be treated as private
data of the request and not accessed directly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The __hci_req_update_scan_rsp_data gets the instance to be updated
which should get passed to update_inst_scan_rsp_data() instead of
always enabling the current instance.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only Sliding Window Size is used at the moment for H5 Bluetooth
Configuration messages.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using hexadecimal notation for mask makes code easier to read
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag just tells us whether hdev->adv_instances is empty or not.
We can equally well use the list_empty() function to get this
information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The code in the Read Advertising Features mgmt command handler is
unnecessarily complicated. Clean it up and remove unnecessary
variables & branches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The request to update HCI during power on is always coming either from
hdev->req_workqueue or through an ioctl, so it's safe to use
hci_req_sync for it. This way we also eliminate potential races with
incoming mgmt commands or other actions while powering on.
Part of this refactoring is the splitting of mgmt_powered() into
mgmt_power_on() and __mgmt_power_off() functions. The main reason is
the different requirements as far as hdev locking is concerned, as
highlighted with the __ prefix of the power off API.
Since the power on in the case of clearing the AUTO_OFF flag cannot be
done synchronously in the set_powered mgmt handler, the hci_power_on
work callback is extended to cover this (which also simplifies the
set_powered helper a lot).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need this both in hci_request.c and mgmt.c so move it to
hci_request.c as a generic helper.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need to update the EIR both from hci_request.c and mgmt.c
so move update_eir() as a more generic request helper to
hci_request.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need this both from hci_request.c and mgmt.c so move it as
a request helper function to hci_request.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the other discoverable changes are behind req_workqueue now it
only makes sense to move the discoverable timeout there as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The discoverable mode is intrinsically linked with the connectable
mode e.g. through sharing the same HCI command (Write Scan Enable) for
BR/EDR. It makes therefore sense to move it to hci_request.c and run
the changes through the same hdev->req_workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Class of Device needs to be changed e.g. for limited discoverable
mode. In preparation of moving the discoverable mode to hci_request.c
and hdev->req_workqueue, move the Class of Device helpers there first.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
